The Development of the Evolutionary BWR

2006 ◽  
Author(s):  
A. Murase ◽  
M. Nakamaru ◽  
M. Kuroki ◽  
Y. Kojima ◽  
S. Yokoyama
Keyword(s):  
Cooling System ◽  
Reactor Core ◽  
Heat Removal ◽  
Safety Performance ◽  
Severe Accident ◽  
Main Role ◽  
Isolation System ◽  
Near Term ◽  
Core Cooling ◽  
Control Rods

Considering the delay of the fast breeding reactor (FBR) development, it is expected that the light water reactor will still play the main role of the electric power generation in the 2030’s. Accordingly, Toshiba has been developing a new conceptual ABWR as the near-term BWR. We tentatively call it AB1600. The AB1600 has introduced the hybrid active/passive safety system in order to improve countermeasure against severe accident (SA). At the same time, we have made the simplification of the overall plant systems in order to improve economy. The simplification of the AB1600 is based on the proven technologies. To retain the safety performance superior or equivalent to the current ABWR and to strengthen the countermeasure against SA, the AB1600 has introduced the passive systems such as the passive containment cooling system (PCCS), the gravity driven core cooling system (GDCS) and the isolation condenser (IC). While we retain the safety performance superior or equivalent to the current ABWR, we have made the simplification of the safety systems. We could eliminate the high pressure core flooder system (HPCF) and the reactor core isolation system (RCIC) by extending the height of reactor pressure vessel (RPV) two meters. To achieve simplification of reactor systems, we have reduced the number of fuel bundles and the number of control rods by adopting large bundle that has a bundle pitch 1.2 times wider than that of the current ABWR. In the 1600MWe class, the number of fuel bundles could be reduced to 600 from 872 of the current ABWR, and the number of control rods could be reduced to 137 from 205 of the current ABWR. Because the reactor internal pump (RIP) of the current ABWR has sufficient performance capacity and the improvement of fuel characteristics from the current fuel enables the operation at lower core flow, the number of RIPs could be decreased from ten to eight. Furthermore, we have reduced the number of divisions of emergency core cooling system (ECCS)/heat removal system to two from three of the current ABWR. This configuration change contributes to reduce the amount of resources of not only reactor systems but also auxiliary systems. In the previous paper, the AB1600 had four low pressure flooder systems (LPFLs). We have studied about the possibility of reduction of LPFLs to two from four by providing the LPFL with alternative injection lines. This change is expected to contribute to reduce the total number of ECCS pumps and the capacity of emergency AC power.

scholarly journals Evaluation of Heat Removal from RBMK-1500 Core Using Control Rods Cooling Circuit

2008 ◽  
Vol 2008 ◽  
pp. 1-8
Author(s):  
A. Kaliatka ◽  
E. Uspuras ◽  
M. Vaisnoras
Keyword(s):  
Nuclear Power ◽  
Cooling System ◽  
Reactor Core ◽  
Heat Removal ◽  
Thermal Inertia ◽  
Severe Accident ◽  
Cooling Circuit ◽  
High Thermal Inertia ◽  
The Moment ◽  
Control Rods

The Ignalina nuclear power plant is a twin unit with two RBMK-1500, graphite moderated, boiling water, multichannel reactors. After the decision was made to decommission the Ignalina NPP, Unit 1 was shut down on December 31, 2004, and Unit 2 is to be operated until the end of 2009. Despite of this fact, severe accident management guidelines for RBMK-1500 reactor at Ignalina NPP are prepared. In case of beyond design basis accidents, it can occur that no water sources are available at the moment for heat removal from fuel channels. Specificity of RBMK reactor is such that the channels with control rods are cooled with water supplied by the system totally independent from the reactor cooling system. Therefore, the heat removal from RBMK-1500 reactor core using circuit for cooling of rods in control and protection system can be used as nonregular mean for reactor cooldown in case of BDBA. The heat from fuel channels, where heat is generated, through graphite bricks is transferred in radial direction to cooled CPS channels. This article presents the analysis of possibility to remove heat from reactor core in case of large LOCA by employing CPS channels cooling circuit. The analysis was performed for Ignalina NPP with RBMK-1500 reactor using RELAP5-3D and RELAP5 codes. Results of the analysis have shown that, in spite of high thermal inertia of graphite, this heat removal from CPS channels allows to slow down effectively the core heat-up process.

Test and Evaluation of a Filtering System for Retention of Fibres in a Coolant Flow After Loss-of-Coolant Accident

2012 ◽  
Author(s):  
T. Gocht ◽  
W. Kästner ◽  
A. Kratzsch ◽  
M. Strasser
Keyword(s):  
Cooling System ◽  
Reactor Core ◽  
Heat Removal ◽  
Test Facility ◽  
Experimental Investigations ◽  
Time Interval ◽  
Insulation Material ◽  
Loss Of Coolant Accident ◽  
Loss Of Coolant ◽  
Core Cooling

In case of an accident the safe heat removal from the reactor core with the installed emergency core cooling system (ECCS) is one of the main features in reactor safety. During a loss-of-coolant accident (LOCA) the release of insulation material fragments in the reactor containment can lead to malfunctions of ECCS. Therefore, the retention of particles by strainers or filtering systems in the ECCS is one of the major tasks. The aim of the presented experimental investigations was the evaluation of a filtering system for the retention of fiber-shaped particles in a fluid flow. The filtering system consists of a filter case with a special lamellar filter unit. The tests were carried out at a test facility with filtering units of different mesh sizes. Insulation material (mineral rock wool) was fragmented to fiber-shaped particles. To simulate the distribution of particle concentration at real plants with large volumes the material was divided into single portions and introduced into the loop with a defined time interval. Material was transported to the filter by the fluid and agglomerated there. The assessment of functionality of the filtering system was made by differential pressure between inlet and outlet of the filtering system and by mass of penetrated particles. It can be concluded that for the tested filtering system no penetration of insulation particles occurred.

Reinforcement of Emergency Power Supply System for Next Generation SFR

2017 ◽  
Author(s):  
Nobuyuki Ishikawa ◽  
Yoshitaka Chikazawa ◽  
Daisuke Sato ◽  
Risako Ikari
Keyword(s):  
Power Supply ◽  
Power Supply System ◽  
Cooling System ◽  
Load Capacity ◽  
Reactor Core ◽  
Heat Removal ◽  
Supply System ◽  
Next Generation ◽  
Emergency Power ◽  
Core Cooling

In this paper, the emergency power supply system for next generation sodium fast reactor (SFR) is investigated to target the latest system design with such as optimized equipment for measure of loss of heat removal system (LOHRS) events, taking into account for strengthening diversity and multiplicity. In addition to diversity and multiplicity, optimization in terms of amount of equipment is also taken into account. The emergency power supply system is consist of emergency generators for design based accident (DBA) and emergency generators to cope with the design extension condition (DEC) in order to power the additional cooling equipment of fuel handling system and reactor core cooling system as a measure for LOHRS event. Base on the load capacity and system operation, the configuration of emergency power supply system was examined aiming optimization of amount of equipment in accordance with some shared use taking into account the reliability. As a result, the emergency power supply system with 4 fixed-type gas turbine generators, 4 portable-type diesel generators and batteries was established.

Application of Thermal Hydraulic and Severe Accident Code SOCRAT/V3 to Bottom Water Reflood Experiment QUENCH-LOCA-1

2016 ◽  
Vol 2 (2) ◽  
Author(s):  
Alexander Vasiliev ◽  
Juri Stuckert
Keyword(s):  
Nuclear Power ◽  
Hydrogen Generation ◽  
Cooling System ◽  
Reactor Core ◽  
Severe Accident ◽  
Loss Of Coolant Accident ◽  
Post Test ◽  
Core Cooling ◽  
Modeling Code ◽  
Code Quality

This study aims to (1) use the thermal hydraulic and severe fuel damage (SFD) best-estimate computer modeling code SOCRAT/V3 for post-test calculation of QUENCH-LOCA-1 experiment and (2) estimate the SOCRAT code quality of modeling. The new QUENCH-LOCA bundle tests with different cladding materials will simulate a representative scenario for a loss-of-coolant-accident (LOCA) nuclear power plant (NPP) accident sequence in which the overheated (up to 1050°C) reactor core would be reflooded from the bottom by the emergency core cooling system (ECCS). The test QUENCH-LOCA-1 was successfully performed at the KIT, Karlsruhe, Germany, on February 2, 2012, and was the first test for this series after the commissioning test QUENCH-LOCA-0 conducted earlier. The SOCRAT/V3-calculated results describing thermal hydraulic, hydrogen generation, and thermomechanical behavior including rods ballooning and burst are in reasonable agreement with the experimental data. The results demonstrate the SOCRAT code’s ability for realistic calculation of complicated LOCA scenarios.

Investigation of Countermeasure Against Local Temperature Rise in Vessel Cooling System in Loss of Core Cooling Test Without Nuclear Heating

2016 ◽  
Vol 2 (4) ◽  
Author(s):  
Masato Ono ◽  
Atsushi Shimizu ◽  
Makoto Kondo ◽  
Yosuke Shimazaki ◽  
Masanori Shinohara ◽  
...  
Keyword(s):  
High Temperature ◽  
Cooling System ◽  
Natural Circulation ◽  
Reactor Core ◽  
Severe Accident ◽  
Local Temperature ◽  
Water Cooling ◽  
The Core ◽  
Cooling Tube ◽  
Core Cooling

In the loss of core cooling test using High Temperature engineering Test Reactor (HTTR), the forced cooling of the reactor core is stopped without inserting control rods into the core and, furthermore, without cooling by the vessel cooling system (VCS) to verify safety evaluation codes to investigate the inherent safety of high-temperature gas-cooled reactor (HTGR) be secured by natural phenomena to make it possible to design a severe accident-free reactor. The VCS passively removes the retained residual heat and the decay heat from the core via the reactor pressure vessel (RPV) by natural convection and thermal radiation. In the test, the local temperature was supposed to exceed the limit from the viewpoint of long-term use at the uncovered water-cooling tube without thermal reflectors in the VCS, although the safety of reactor is kept. Through a cold test, which was carried out by non-nuclear heat input from helium gas circulators (HGCs) by stopping water flow in the VCS, the local higher temperature position was specified in the uncovered water-cooling tube of the VCS, although the temperature was sufficiently lower than the maximum allowable working temperature, and the natural circulation of water had an insufficient cooling effect on the temperature of the water-cooling tube below 1°C. Then, a new safe and secured procedure for the loss of core cooling test was established, which will be carried out soon after the restart of HTTR.

scholarly journals Simulation of a severe accident at a typical PWR due to break of a hot leg ECCS injection line using MELCOR code.

2019 ◽  
Vol 7 (2B) ◽  
Author(s):  
Seung Min Lee ◽  
Nelbia Da Silva Lapa ◽  
Gaianê Sabundjian
Keyword(s):  
Cooling System ◽  
Severe Accident ◽  
Time Intervals ◽  
Severe Accidents ◽  
Independent Analysis ◽  
Accident Management ◽  
Injection Line ◽  
Core Cooling ◽  
Control Volumes ◽  
Physical Phenomena

The aim of this work was to simulate a severe accident at a typical PWR, initiated with a break in Emergency Core Cooling System line of a hot leg, using the MELCOR code. The model of this typical PWR was elaborated by the Global Research for Safety and provided to the CNEN for independent analysis of the severe accidents at Angra 2, which is similar to this typical PWR. Although both of them are not identical, the results obtained of that typical PWR may be valuable because of the lack of officially published simulation of severe accident at Angra 2. Relevant parameters such as pressure, temperature and water level in various control volumes, after the break at the hot leg, were calculated as well as degree of core degradation and hydrogen production within the containment. The result obtained in this work could be considered satisfactory in the sense that the physical phenomena reproduced by the simulation were in general very reasonable, and most of the events occurred within acceptable time intervals. However, the uncertainty analysis was not carried out in this work. Furthermore, this scenario could be used as a base for the study of the effectiveness of some preventive or/and mitigating measures of Severe Accident Management by implementing each measure in this model.

scholarly journals Thermal Hydraulic Analysis of a Nuclear Reactor due to Loss of Coolant Accident with and without Emergency Core Cooling System

2020 ◽  
Vol 01 (02) ◽  
pp. 53-60
Author(s):  
Pronob Deb Nath ◽  
Kazi Mostafijur Rahman ◽  
Md. Abdullah Al Bari
Keyword(s):  
Nuclear Reactor ◽  
Cooling System ◽  
Computational Study ◽  
Reactor Core ◽  
Primary Circuit ◽  
Feed Water ◽  
Pressurized Water ◽  
Loss Of Coolant Accident ◽  
Loss Of Coolant ◽  
Core Cooling

This paper evaluates the thermal hydraulic behavior of a pressurized water reactor (PWR) when subjected to the event of Loss of Coolant Accident (LOCA) in any channel surrounding the core. The accidental break in a nuclear reactor may occur to circulation pipe in the main coolant system in a form of small fracture or equivalent double-ended rupture of largest pipe connected to primary circuit line resulting potential threat to other systems, causing pressure difference between internal parts, unwanted core shut down, explosion and radioactivity release into environment. In this computational study, LOCA for generation III+ VVER-1200 reactor has been carried out for arbitrary break at cold leg section with and without Emergency Core Cooling System (ECCS). PCTRAN, a thermal hydraulic model-based software developed using real data and computational approach incorporating reactor physics and control system was employed in this study. The software enables to test the consequences related to reactor core operations by monitoring different operating variables in the system control bar. Two types of analysis were performed -500% area break at cold leg pipe due to small break LOCA caused by malfunction of the system with and without availability of ECCS. Thermal hydraulic parameters like, coolant dynamics, heat transfer, reactor pressure, critical heat flux, temperature distribution in different sections of reactor core have also been investigated in the simulation. The flow in the reactor cooling system, steam generators steam with feed-water flow, coolant steam flow through leak level of water in different section, power distribution in core and turbine were plotted to analyze their behavior during the operations. The simulation showed that, LOCA with unavailability of Emergency Core Cooling System (ECCS) resulted in core meltdown and release of radioactivity after a specific time.

The Development of the Evolutionary BWR (AB1600)

2008 ◽  
Author(s):  
Akira Murase ◽  
Mikihide Nakamaru ◽  
Ryoichi Hamazaki ◽  
Masahiko Kuroki ◽  
Munetaka Takahashi
Keyword(s):  
Fuel Cycle ◽  
Safety System ◽  
Safety Performance ◽  
Passive Safety ◽  
Main Role ◽  
Core Diameter ◽  
The Core ◽  
Passive Safety System ◽  
Bundle Size ◽  
Near Term

Considering the delay of the first breeding reactor (FBR), it is expected that the light water reactor will still play the main role of the electric power generation in the 2030’s. Accordingly, Toshiba has been developing a new conceptual ABWR as the near-term BWR. We tentatively call it AB1600. The AB1600 has introduced the hybrid active/passive safety system in order to have independent countermeasure for severe accidents and better probability of core damage frequency (CDF) considered external events such as earthquake. On the other hand, we have another goal of the AB1600, which is to retain the safety performance superior or equivalent to the current ABWR without deterioration of economy. In order to achieve both economy and safety performance, we have optimized the safety system configuration of the AB1600 by partly introducing passive safety system to design basis event (DBEs). At the same time, we have adopted the simplification of the overall plant systems in order to improve economy. In order to reduce capital cost, to shorten refueling period and to reduce maintenance effort, the AB1600 introduces the large fuel bundle size. The bundle size is 1.2 times as large as that of the ABWR and the fuel rod array is 12 by 12. And then by progressing the core design, we can reduce the number of reactor internal pumps (RIPs) to eight from the current ABWR of ten. The core power density, the number of fuel bundles, and the core diameter of AB1600 are decided in order to achieve 24 months fuel cycle length on the condition with below 5wt% enrichment of fuel and with eight RIPs.

Severe Accident Analysis for BWR With Containment Outer Pool

2012 ◽  
Author(s):  
Koki Yoshimura ◽  
Kohei Hisamochi
Keyword(s):  
Cooling System ◽  
Water Injection ◽  
Heat Removal ◽  
Severe Accident ◽  
Gas Temperature ◽  
Passive System ◽  
Active Components ◽  
Active System ◽  
Station Blackout ◽  
Materials Used

Newly designed plants, e.g., next-generation light water reactor or ESBWR, employ a passive containment cooling system and have an enhanced safety with RHRs (Residual Heat Removal system) including active components. Passive containment cooling systems have the advantage of a simple mechanism, while materials used for the systems are too large to employ these systems to existing plants. Combination of passive system and active system is considered to decrease amount of material for existing plants. In this study, alternatives of applying containment outer pool as a passive system have been developed for existing BWRs, and effects of outer pool on BDBA (Beyond Design Basis Accident) have been evaluated. For the evaluation of containment outer pool, it is assumed that there would be no on-site power at the loss of off-site power event, so called “SBO (Station BlackOut)”. Then, the core of this plant would be uncovered, heated up, and damaged. Finally, the reactor pressure vessel would be breached. Containment gas temperature reached the containment failure temperature criteria without water injection. With water injection, containment pressure reached the failure pressure criteria. With this situation, using outer pool is one of the candidates to mitigate the accident. Several case studies for the outer pool have been carried out considering several parts of containment surface area, which are PCV (Pressure Containment vessel) head, W/W (Wet Well), and PCV shell. As a result of these studies, the characteristics of each containment outer pool strategies have become clear. Cooling PCV head can protect it from over-temperature, although its effect is limited and W/W venting can not be delayed. Cooling suppression pool has an effect of pressure suppressing effect when RPV is intact. Cooling PCV shell has both effect of decreasing gas temperature and suppressing pressure.

Preliminary Severe Accident Analysis of Fusion-Fission Hybrid Reactor Using the MELCOR Code

2014 ◽  
Author(s):  
Zhang Dabin ◽  
Zhiwei Zhou ◽  
Heng Xie ◽  
Tang Yang
Keyword(s):  
Cooling System ◽  
Safety Performance ◽  
Severe Accident ◽  
Hybrid Reactor ◽  
Accident Analysis ◽  
Analysis Model ◽  
Decay Heat ◽  
Calculation Results ◽  
Core Meltdown ◽  
Dry Out

The fusion-fission hybrid conceptual reactor is a proposed means of generating power, which adopts a water cooled fission blanket based on ITER. Due to the water cooled fission blanket, safety performance of the hybrid reactor should be considered, including decay heat remove, core uncovered, core meltdown, core degradation, radioactivity releases, etc., similar with the PWRs. The main goal of this work is to develop the fission blanket model by using MELCOR code, and to evaluate the safety performance under severe accidents preliminarily. Based on MELCOR 1.8.5, some modification is made for the severe accident analysis of fission blanket. Using modified MELCOR code, an analysis model is developed for the fission blanket and the cooling loop. The strategy of the In-Vessel Retention (IVR) using the ex-vessel cooling method is evaluated during a large break LOCA. The calculation results describes the main phenomena during the severe accident progression, including core dry out, meltdown, relocation, etc.. Simulation result is shown that the decay heat in the fission zone can be removed out by the ex-vessel cooling system merely, and the fuel max temperature will not reach the melting point.

Sign in / Sign up

Export Citation Format

Share Document