Two-Phase Boiling Flow in Microchannels: Instabilities Issues and Flow Regime Mapping

Author(s):  
Y. Peles

The design, fabrication, and evaluation of forced convection boiling two-phase flow, micro scale heat exchanger are described. The micro heat exchanger consist of a heater, and 16 mm long multiple parallel triangular micro channels, with hydraulic diameter ranging from 50 μm to 200 μm. The system allowed simultaneously visualizing the flow regime, to measure the resistor temperature distribution, the pressure drop, and input power levels. Experiments were conducted using water with mass flow rate of 1–10 g/min and heat fluxes ranging from 10–60 W/cm2 in order to better understand the flow mechanism associated with micro scale forced convection boiling two-phase flow. The pressure drop, temperature, fluctuation and flow regimes map were obtained. The results are consistent with newly reported studies and show that flow fluctuation at that scale is exaggerated with respect to conventional size channels. A unique flow regime was observed and was named “rapid bubble growth”.

Author(s):  
Namwon Kim ◽  
Estelle T. Evans ◽  
Steven A. Soper ◽  
Michael C. Murphy ◽  
Dimitris E. Nikitopoulos

This study addresses air-water, two-phase flows in micro-channels fabricated on poly-methyl-methacrylate (PMMA) with walls that are partially non-wetting (typical static contact angle 65° in stock form) and not molecularly smooth. Two different types of chips were prepared: Micro-milled micro-channels of aspect ratios 1, 2 and 3 with fixed hydraulic diameter on PMMA and micro-channels of unity aspect ratio replicated using hot embossing of PMMA with a micro-milled brass mold insert. Flow-maps obtained using the same gas-liquid injection geometry and method for the three aspect ratio micro-channels are presented, and regime boundaries are compared with those found by other investigations. The results indicate that the bubbly flow regime boundary is shifted to higher liquid and/or lower gas superficial velocities for the higher aspect ratio channels, while transition to the Annular and Annular-Dry regimes remains the same to within experimental uncertainty. The emphasis of what is presented is on the Segmented flow regime. Regular and irregular Segmented flow regimes of three types are assessed on the basis of the statistical variation in the associated phase length scales from flow observations over a substantial channel length. Comparison between results of the two different injection geometries and micro-channel manufacturing techniques indicate that feedback effects are a significant but not the only cause of segmented flow irregularity. The variability in the size of the liquid plug separating gas bubbles in Segmented flow is found to be substantially higher than that of the bubbles even when the flow is regular (low variability of bubble size). The average bubble length associated with a part of Segmented flows, regular and irregular alike is shown to scale approximately with the capillary number to the 2/3 power (liquid volumetric flow ratio to the −2/3). Irregular Segmented flow is favored by higher liquid superficial velocities, lower liquid volumetric flow ratios and lower channel aspect ratios. Of the three aspect ratios examined, the microchannel with aspect-ratio 3 displayed the broadest window of regular Segmented flow. Two-phase flow pressure drop was measured for test channels of unity aspect ratio. Each flow regime identified on the basis of topological observations is associated with different trends of the pressure drop variation with respect to volumetric flow ratio.


Micromachines ◽  
2021 ◽  
Vol 12 (5) ◽  
pp. 510
Author(s):  
Yan Huang ◽  
Bifen Shu ◽  
Shengnan Zhou ◽  
Qi Shi

In this paper, two-phase pressure drop data were obtained for boiling in horizontal rectangular microchannels with a hydraulic diameter of 0.55 mm for R-134a over mass velocities from 790 to 1122, heat fluxes from 0 to 31.08 kW/m2 and vapor qualities from 0 to 0.25. The experimental results show that the Chisholm parameter in the separated flow model relies heavily on the vapor quality, especially in the low vapor quality region (from 0 to 0.1), where the two-phase flow pattern is mainly bubbly and slug flow. Then, the measured pressure drop data are compared with those from six separated flow models. Based on the comparison result, the superficial gas flux is introduced in this paper to consider the comprehensive influence of mass velocity and vapor quality on two-phase flow pressure drop, and a new equation for the Chisholm parameter in the separated flow model is proposed as a function of the superficial gas flux . The mean absolute error (MAE ) of the new flow correlation is 16.82%, which is significantly lower than the other correlations. Moreover, the applicability of the new expression has been verified by the experimental data in other literatures.


Author(s):  
Weilin Qu ◽  
Seok-Mann Yoon ◽  
Issam Mudawar

Knowledge of flow pattern and flow pattern transitions is essential to the development of reliable predictive tools for pressure drop and heat transfer in two-phase micro-channel heat sinks. In the present study, experiments were conducted with adiabatic nitrogen-water two-phase flow in a rectangular micro-channel having a 0.406 × 2.032 mm cross-section. Superficial velocities of nitrogen and water ranged from 0.08 to 81.92 m/s and 0.04 to 10.24 m/s, respectively. Flow patterns were first identified using high-speed video imaging, and still photos were then taken for representative patterns. Results reveal that the dominant flow patterns are slug and annular, with bubbly flow occurring only occasionally; stratified and churn flow were never observed. A flow pattern map was constructed and compared with previous maps and predictions of flow pattern transition models. Annual flow is identified as the dominant flow pattern for conditions relevant to two-phase micro-channel heat sinks, and forms the basis for development of a theoretical model for both pressure drop and heat transfer in micro-channels. Features unique to two-phase micro-channel flow, such as laminar liquid and gas flows, smooth liquid-gas interface, and strong entrainment and deposition effects are incorporated into the model. The model shows good agreement with experimental data for water-cooled heat sinks.


2020 ◽  
Vol 368 ◽  
pp. 110815
Author(s):  
Yue Jin ◽  
Fan-Bill Cheung ◽  
Koroush Shirvan ◽  
Stephen M. Bajorek ◽  
Kirk Tien ◽  
...  

Author(s):  
Christian Weinmu¨ller ◽  
Dimos Poulikakos

Microfluidics has experienced a significant increase in research activities in recent years with a wide range of applications emerging, such as micro heat exchangers, energy conversion devices, microreactors, lab-on-chip devices and micro total chemical analysis systems (μTAS). Efforts to enhance or extend the performance of single phase microfluidic devices are met by two-phase flow systems [1, 2]. Essential for the design and control of microfluidic systems is the understanding of the fluid/hydrodynamic behavior, especially pressure drop correlations. These are well established for single phase flow, however, analytical correlations for two-phase flow only reflect experimentally obtained values within an accuracy of ± 50% [3, 4]. The present study illustrates the effect of two-phase flow regimes on the pressure drop. Experimental measurement data is put into relation of calculated values based on established correlations of Lockhart-Martinelli with Chisholm modifications for macroscopic flows [5, 6] and Mishima-Hibiki modifications for microscale flows [7]. Further, the experimental pressure drop data is superimposed onto two-phase flow maps to identify apparent correlations of pressure drop abnormalities and flow regimes. The experiments were conducted in a square microchannel with a width of 200 μm. Optical access is guaranteed by an anodically bonded glass plate on a MEMS fabricated silicon chip. Superficial velocities range from 0.01 m/s to 1 m/s for the gas flow and from 0.0001 m/s to 1 m/s for the liquid flow with water as liquid feed and CO2 as gas. The analysis of the flow regimes was performed by imaging the distinct flow regimes by laser induced fluorescence microscopy, employing Rhodamine B as the photosensitive dye. The pressure drop was synchronically recorded with a 200 mbar, 2.5 bar and 25 bar differential pressure transmitter and the data was exported via a LabView based software environment, see Figure 1. Figure 2 illustrates the experimentally obtained pressure drop in comparison to the calculated values based on the Lockhard-Martinelli correlation with the Chisholm modification and the Mishima-Hibiki modification. For both cases the predications underestimate the two-phase pressure drop by more than 50%. Nevertheless, the regression of the experimental data has an offset of linear nature. Two-phase flow is assigned to flow regime maps of bubbly, wedging, slug or annular flow defined by superficial gas and liquid velocities. In Figure 3 the pressure drop is plotted as a surface over the corresponding flow regime map. Transition lines indicate a change of flow regimes enclosing an area of an anticline in the pressure data. In the direct comparison between the calculated and the measured values, the two surfaces show a distinct deviation. Especially, the anticline of the experimental data is not explained by the analytical correlations. Figure 4 depicts the findings of Figure 3 at a constant superficial velocity of 0.0232 m/s. The dominant influence of the flow regimes on the pressure drop becomes apparent, especially in the wedging flow regime. The evident deviation of two-phase flow correlations for the pressure drop is based on omitting the influence of the flow regimes. In conclusion, the study reveals a strong divergence of pressure drop measurements in microscale two-phase flow from established correlations of Lockhart-Martinelli and recognized modifications. In reference to [8, 9], an analytical model incorporating the flow regimes and, hence, predicting the precise pressure drop would be of great benefit for hydrodynamic considerations in microfluidics.


Sign in / Sign up

Export Citation Format

Share Document