Accelerometer Signal to Characterize the Combustion Development in Multiple Injection Diesel Engine

2012 ◽  
Author(s):  
G. Chiatti ◽  
O. Chiavola ◽  
E. Recco
Keyword(s):  
Diesel Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Vibration Signal ◽  
Injection System ◽  
Cylinder Pressure ◽  
Multiple Injection ◽  
Real Time Control ◽  
Common Rail Injection System ◽  
Crank Angle

This work constitutes one of the last steps of a comprehensive research program in which vibration sensors are used with the purpose of developing and setting up a methodology that is able to perform a real time control of the combustion process by means of non-intrusive measurements. Previous obtained and published results have demonstrated that a direct relationship exists between in-cylinder pressure and engine block vibration signals. The analysis of the processed data have highlighted that the block vibration signal may be used to locate, in the crank–angle domain, the combustion phases (the start of the combustion, the crank angle value corresponding to the beginning of main combustion and to the in-cylinder pressure maximum value) and to quantify the in-cylinder pressure development by evaluating the pressure peak value and the pressure rise rate caused by the combustion process. The aim of this work is to extend and validate the developed methodology when a multiple-injection strategy is imposed on the engine. The paper presents the results obtained during the experimentation of a two cylinder diesel engine equipped with a common rail injection system, that was performed in the Laboratory of the Mechanical and Industrial Department of ‘ROMA TRE’ University. During the tests, a wide variation of the injection parameters settings is imposed on the engine (timing and duration) in its complete operative field.

Experimental investigation of the combustion characteristics of a biodiesel (rice-bran oil methyl ester)-fuelled direct-injection transportation diesel engine

2007 ◽  
Vol 221 (8) ◽  
pp. 921-932 ◽  
Author(s):  
S Sinha ◽  
A K Agarwal
Keyword(s):  
Diesel Engine ◽  
Methyl Ester ◽  
Vegetable Oils ◽  
Rice Bran ◽  
Rice Bran Oil ◽  
Direct Injection ◽  
Pressure Rise ◽  
Cylinder Pressure ◽  
Biodiesel Blends ◽  
Crank Angle

Increased environmental awareness and depletion of fossil petroleum resources are driving industry to develop alternative fuels that are environmentally more acceptable. Transesterified vegetable oil derivatives called ‘biodiesel’ appear to be the most convenient way of utilizing bio-origin vegetable oils as substitute fuels in diesel engines. The methyl esters of vegetable oils do not require significant modification of existing engine hardware. Previous research has shown that biodiesel has comparable performance and lower brake specific fuel consumption than diesel with significant reduction in emissions of CO, hydrocarbons (HC), and smoke but slightly increased NO x emissions. In the present experimental research work, methyl ester of rice-bran oil is derived through transesterification of rice-bran oil using methanol in the presence of sodium hydroxide (NaOH) catalyst. Experimental investigations have been carried out to examine the combustion characteristics in a direct injection transportation diesel engine running with diesel, biodiesel (rice-bran oil methyl ester), and its blends with diesel. Engine tests were performed at different engine loads ranging from no load to rated (100 per cent) load at two different engine speeds (1400 and 1800 r/min). A careful analysis of the cylinder pressure rise, heat release, and other combustion parameters such as the cylinder peak combustion pressure, rate of pressure rise, crank angle at which peak pressure occurs, rate of pressure rise, and mass burning rates was carried out. All test fuels exhibited similar combustion stages as diesel; however, biodiesel blends showed an earlier start of combustion and lower heat release during premixed combustion phase at all engine load-speed combinations. The maximum cylinder pressure reduces as the fraction of biodiesel increases in the blend and, at higher engine loads, the crank angle position of the peak cylinder pressure for biodiesel blends shifted away from the top dead centre in comparison with baseline diesel data. The maximum rate of pressure rise was found to be higher for diesel at higher engine loads; however, combustion duration was higher for biodiesel blends.

Simulation Research of the Effect of Compression Ratios on Combustion and Emission for Methanol/Diesel Dual Fuel Engine

2014 ◽  
Vol 709 ◽  
pp. 78-82
Author(s):  
Xu Dong Zhang ◽  
Yin Nan Yuan ◽  
Jia Yi Du
Keyword(s):  
Diesel Engine ◽  
Combustion Process ◽  
Pressure Rise ◽  
Delay Period ◽  
Dual Fuel ◽  
Ignition Timing ◽  
Simulation Research ◽  
Rise Rate ◽  
Crank Angle ◽  
Ignition Delay Period

This paper has studied the influence of the different ratio on combustion process and emissions of air premixed methanol/diesel dual fuel engine. The research was based on 4B26 diesel engine, and the 3-D numerical simulation on combustion process and emissions of the diesel engine with intake premixed methanol was carried out using AVL FIRE software. The study showed that,with the compression ratio reducing,the ignition delay period prolonged, and the ignition timing delayed, the maximum firing pressure, the peak of pressure rise rate and the maximum combustion temperature in cylinder decreased, the crank angle postponed, the NOX emission decreased and the Soot emission increased obviously.

Simulation Research on Post-Injection of Electronically Controlled Heavy-Duty Diesel Engine

2011 ◽  
Vol 121-126 ◽  
pp. 2238-2242
Author(s):  
Ming Hai Li ◽  
Feng Jiang ◽  
Biao Liu ◽  
Ming Gao Ouyang
Keyword(s):  
Diesel Engine ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Process ◽  
Pressure Rise ◽  
Injection System ◽  
Post Injection ◽  
Simulation Research ◽  
Di Diesel Engine ◽  
Heavy Duty Diesel

GT-Suite software is used to establish the simulation model of electronic fuel injection system for 16V280ZJ diesel engine. Combustion process simulation calculation is conducted to the direct injection (DI) diesel engine based on a main-post double injection scheme. Simulation parameters are modified based on the comparison with given experimental results. The calculation results effectively reflect the influence of fuel ratio and the interval angle between main and post injection over emission and fuel economy. Finally, in order to improve the engine emissions and reduce the pressure rise rate, we get the optimal injection solution for the main-post injection mode.

scholarly journals Effects of Injection Rate Profile on Combustion Process and Emissions in a Diesel Engine

2017 ◽  
Vol 2017 ◽  
pp. 1-8 ◽  
Author(s):  
Fuqiang Bai ◽  
Zuowei Zhang ◽  
Yongchen Du ◽  
Fan Zhang ◽  
Zhijun Peng
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Combustion Process ◽  
Injection Rate ◽  
Injection System ◽  
Nox Emissions ◽  
Release Process ◽  
Common Rail Injection System ◽  
Soot Emissions ◽  
Rate Profile

When multi-injection is implemented in diesel engine via high pressure common rail injection system, changed interval between injection pulses can induce variation of injection rate profile for sequential injection pulse, though other control parameters are the same. Variations of injection rate shape which influence the air-fuel mixing and combustion process will be important for designing injection strategy. In this research, CFD numerical simulations using KIVA-3V were conducted for examining the effects of injection rate shape on diesel combustion and emissions. After the model was validated by experimental results, five different shapes (including rectangle, slope, triangle, trapezoid, and wedge) of injection rate profiles were investigated. Modeling results demonstrate that injection rate shape can have obvious influence on heat release process and heat release traces which cause different combustion process and emissions. It is observed that the baseline, rectangle (flat), shape of injection rate can have better balance between NOx and soot emissions than the other investigated shapes. As wedge shape brings about the lowest NOx emissions due to retarded heat release, it produces the highest soot emissions among the five shapes. Trapezoid shape has the lowest soot emissions, while its NOx is not the highest one. The highest NOx emissions were produced by triangle shape due to higher peak injection rate.

Optimal Design of a Two-Stroke Diesel Engine for Aeronautical Applications Concerning Both Thermofluidynamic and Acoustic Issues

2008 ◽  
Author(s):  
Daniela Siano ◽  
Michela Costa ◽  
Fabio Bozza
Keyword(s):  
Diesel Engine ◽  
Acoustic Analysis ◽  
Fluid Dynamic ◽  
Combustion Process ◽  
Engine Performance ◽  
Combustion Noise ◽  
Process Efficiency ◽  
Injection System ◽  
Common Rail Injection System ◽  
First Choice

Some aspects concerning the development of a prototype of a diesel engine suitable for aeronautical applications are discussed. The engine aimed at achieving a weight to power ratio equal to one kg/kW (220 kg for 220 kW) is conceived in a two stroke Uniflow configuration and constituted by six cylinders distributed on two parallel banks. Basing on a first choice of some geometrical and operational data, a preliminary fluid-dynamic and acoustic analysis is carried out at the sea level. This includes the engine-turbocharger matching, the estimation of the scavenging process efficiency, and the simulation of the spray and combustion process, arising from a Common Rail injection system. Both 1D and 3D CFD models are employed. In-cylinder pressure cycles are utilized to numerically predict the combustion noise. The acoustic study is based on the integration of FEM/BEM codes. In order to improve the engine performance and vibro-acoustic behaviour, the 1D model, tuned with information derived from the 3D code, is linked to an external optimiziation code (ModeFRONTIER™). A constrained multi-objective optimization is performed to contemporary minimize the fuel consumption and the maximum in-cylinder temperature and pressure gradient. In this way a better selection of a number of engine parameters is carried out (exhaust valve opening, closing and lift, intake ports heights, start of injection, etc). The best found solution is finally compared to the initial one and some substantial design improvements are discussed.

Drive Cycle Efficiency and Emissions Estimates for Reactivity Controlled Compression Ignition in a Multi-Cylinder Light-Duty Diesel Engine

2011 ◽  
Author(s):  
Scott J. Curran ◽  
Kukwon Cho ◽  
Thomas E. Briggs ◽  
Robert M. Wagner
Keyword(s):  
Diesel Engine ◽  
Pressure Rise ◽  
Injection System ◽  
Compression Ignition ◽  
Cylinder Pressure ◽  
Drive Cycle ◽  
Reactivity Controlled Compression Ignition ◽  
Pressure Rise Rate ◽  
Light Duty ◽  
Rise Rate

In-cylinder blending of gasoline and diesel to achieve Reactivity Controlled Compression Ignition (RCCI) has been shown to reduce NOx and PM emissions while maintaining or improving brake thermal efficiency (BTE) as compared to conventional diesel combustion (CDC). The RCCI concept has an advantage over many advanced combustion strategies in that by varying both the percent of premixed gasoline and EGR rate, stable combustion can be extended over more of the light-duty drive cycle load range. Changing the percent of premixed gasoline changes the fuel reactivity stratification in the cylinder providing further control of combustion phasing and cylinder pressure rise rate than the use of EGR alone. This paper examines the combustion and emissions performance of light-duty diesel engine using direct injected diesel fuel and port injected gasoline to enable RCCI for steady-state engine conditions which are consistent with a light-duty drive cycle. A GM 1.9L four-cylinder engine with the stock compression ratio of 17.5:1, common rail diesel injection system, high-pressure EGR system and variable geometry turbocharger was modified to allow for port fuel injection with gasoline. Engine-out emissions, engine performance and combustion behavior for RCCI operation is compared against both CDC and a premixed charge compression ignition (PCCI) strategy which relies on high levels of EGR dilution. The effect of percent of premixed gasoline, EGR rate, boost level, intake mixture temperature, combustion phasing, and cylinder pressure rise rate is investigated for RCCI combustion for the light-duty modal points. Engine-out emissions of NOx and PM were found to be considerably lower for RCCI operation as compared to CDC and PCCI, while HC and CO emissions were higher. BTE was similar or higher for many of the modal conditions for RCCI operation. The emissions results are used to estimate hot-start FTP-75 emissions levels with RCCI and are compared against CDC and PCCI modes.

Investigation on the Match between the Nozzle Tip Penetration and the Double-Layers Diffluent Combustion Chamber Geometry

2013 ◽  
Vol 860-863 ◽  
pp. 1738-1743
Author(s):  
Kun Peng Qi ◽  
Ming Hai Li ◽  
Wu Qiang Long
Keyword(s):  
Diesel Engine ◽  
Combustion Chamber ◽  
Fuel Injection ◽  
Combustion Process ◽  
Fuel Mixture ◽  
Injection System ◽  
Double Layers ◽  
Cylinder Pressure ◽  
Combustion System ◽  
Ratio Distribution

In order to investigate the match between the nozzle tip penetration and the double-layers diffluent combustion chamber geometry, a simulation model was developed which was based on the 135 diesel engine to simulate the equivalence ratio distribution of air-fuel mixture and the temperature distribution during combustion process. At the same time, an experiment was executed by a 135 diesel engine equipped with the high-pressure common rail fuel injection system. The research results show that the air-fuel mixture becomes more uniformed and the combustion process is improved when the nozzle tip penetration is reasonable selected which lead to higher in-cylinder pressure and better brake specific fuel consumption while NOXemission is increased and soot emission is decreased for the double-layers diffluent combustion system.

Study on Methanol/Biodiesel for Agricultural Diesel Engines Applications

2014 ◽  
Vol 912-914 ◽  
pp. 475-478
Author(s):  
Rui Na Li ◽  
Zhong Wang ◽  
Ling Chuan Hou ◽  
Ming Di Li
Keyword(s):  
Diesel Engine ◽  
Combustion Process ◽  
Chemical Properties ◽  
Pressure Rise ◽  
Calculation Model ◽  
Maximum Pressure ◽  
Physical And Chemical Properties ◽  
Cylinder Pressure ◽  
Physical And Chemical ◽  
And Chemical Properties

According to the physical and chemical properties of methanol, fuel was prepared using the methanol and biodiesel. The physical and chemical properties of the blends were investigated, and the combustion process calculation model of 186FA diesel engine was established. The spray characteristics and in-cylinder pressure were calculated of diesel engine fueled with the blend of biodiesel added with 15% methanol at 3000r/min, 5.7kW. The results show that, the spray penetration shortens and the sauter mean diameter reduces when diesel engine fueled with methanol/biodiesel, besides, the maximum cylinder pressure reduces. However, the maximum pressure rise rate increases.

Sign in / Sign up

Export Citation Format

Share Document