scholarly journals Tailoring Charge Reactivity Using In-Cylinder Generated Reformate for Gasoline Compression Ignition Strategies

2016 ◽  
Author(s):  
Isaac W. Ekoto ◽  
Benjamin M. Wolk ◽  
William F. Northrop ◽  
Nils Hansen ◽  
Kai Moshammer
Keyword(s):  
Performance Metrics ◽  
Engine Performance ◽  
Combustion Stability ◽  
Gas Temperature ◽  
Exhaust Temperature ◽  
Start Of Injection ◽  
Main Period ◽  
Piston Crevice ◽  
Ignition Characteristics ◽  
Negative Valve Overlap

In-cylinder reforming of injected fuel during an auxiliary negative valve overlap (NVO) period can be used to optimize main-cycle combustion phasing for low-load Low-Temperature Gasoline Combustion, where highly dilute mixtures can lead to poor combustion stability. The objective of this work is to examine the effects of reformate composition on main-cycle engine performance for a research gasoline. A custom alternate-fire sequence with nine pre-conditioning cycles was used to generate a common exhaust temperature and composition boundary condition for a cycle-of-interest. Performance metrics such as main-period combustion stability and total cycle efficiency were collected for these custom cycles. The NVO-produced reformate stream was also separately collected using a dump valve apparatus and characterized in detail using both gas chromatography and photoionization mass spectroscopy. To facilitate gas sample analysis, sampling experiments were conducted using a five-component gasoline surrogate (iso-octane, n-heptane, ethanol, 1-hexene, and toluene) that matched the molecular composition, 50% boiling point, and ignition characteristics of the research gasoline. For the gasoline, it was found that the most advanced NVO start-of-injection (SOI) led to the most advanced main-cycle 10% burn angle. The effect was more pronounced as the fraction of total fuel injected in the NVO period increased. With the most retarded NVO SOI, shorter residence times and piston spray impingement limited the opportunity for injected fuel decomposition. For the gasoline surrogate, the most advanced NVO SOI had reduced reactivity relative to more intermediate NVO SOI, which was attributed to rapid in-cylinder mixing that led to a large amount of fuel quench in the piston crevice. For all NVO periods, combustion phasing advanced as the main-period fueling decreased. Slower kinetics for leaner mixtures were offset by a combination of increased bulk-gas temperature from higher charge specific heat ratios and increased fuel reactivity due to higher charge reformate fractions.

scholarly journals Tailoring Charge Reactivity Using In-Cylinder Generated Reformate for Gasoline Compression Ignition Strategies

2017 ◽  
Vol 139 (12) ◽  
Author(s):  
Isaac W. Ekoto ◽  
Benjamin M. Wolk ◽  
William F. Northrop ◽  
Nils Hansen ◽  
Kai Moshammer
Keyword(s):  
Performance Metrics ◽  
Engine Performance ◽  
Gas Temperature ◽  
Exhaust Temperature ◽  
Start Of Injection ◽  
Low Load ◽  
Main Period ◽  
Ignition Characteristics ◽  
Negative Valve Overlap ◽  
Valve Overlap

In-cylinder reforming of injected fuel during a negative valve overlap (NVO) recompression period can be used to optimize main-cycle combustion phasing for low-load low-temperature gasoline combustion (LTGC). The objective of this work is to examine the effects of reformate composition on main-cycle engine performance. An alternate-fire sequence was used to generate a common exhaust temperature and composition boundary condition for a cycle-of-interest, with performance metrics measured for these custom cycles. NVO reformate was also separately collected using a dump-valve apparatus and characterized by both gas chromatography (GC) and photoionization mass spectroscopy (PIMS). To facilitate gas sample analysis, sampling experiments were conducted using a five-component gasoline surrogate (iso-octane, n-heptane, ethanol, 1-hexene, and toluene) that matched the molecular composition, 50% boiling point, and ignition characteristics of the research gasoline. For the gasoline, it was found that an advance of the NVO start-of-injection (SOI) led to a corresponding advance in main-period combustion phasing as the combination of longer residence times and lower amounts of liquid spray piston impingement led to a greater degree of fuel decomposition. The effect was more pronounced as the fraction of total fuel injected in the NVO period increased. Main-period combustion phasing was also found to advance as the main-period fueling decreased. Slower kinetics for leaner mixtures were offset by a combination of increased bulk-gas temperature from higher charge specific heat ratios and increased fuel reactivity due to higher charge reformate fractions.

Implementation Challenges and Solutions for Homogenous Charge Compression Ignition Combustion in Diesel Engines

2014 ◽  
Author(s):  
Usman Asad ◽  
Ming Zheng ◽  
David Ting ◽  
Jimi Tjong
Keyword(s):  
High Pressure ◽  
Diesel Engines ◽  
Performance Metrics ◽  
Pressure Rise ◽  
Engine Performance ◽  
Injection Pressure ◽  
Combustion Stability ◽  
Compression Ignition ◽  
Hcci Combustion ◽  
Homogenous Charge Compression Ignition

Homogenous charge compression ignition (HCCI) combustion in diesel engines can provide for cleaner operation with ultra-low NOx and soot emissions. While HCCI combustion has generated significant attention in the last decade, however, to date, it has seen very limited application in production diesel engines. HCCI combustion is typically characterized by earlier than top-dead-center (pre-TDC) phasing, very high pressure rise rates, short combustion durations and minimal control over the timing of the combustion event. To offset the high reactivity of the diesel fuel, large amounts of EGR (30 to 60%) are usually applied to postpone the initiation of combustion, shift the combustion towards TDC and alleviate to some extent, the high pressure rise rates and the reduced energy efficiency. In this work, a detailed analysis of HCCI combustion has been carried out on a high-compression ratio, single-cylinder diesel engine. The effects of intake boost, EGR quantity/temperature, engine speed, injection scheduling and injection pressure on the operability limits have been empirically determined and correlated with the combustion stability, emissions and performance metrics. The empirical investigation is extended to assess the suitability of common alternate fuels (n-butanol, gasoline and ethanol) for HCCI combustion. On the basis of the analysis, the significant challenges affecting the real-world application of HCCI are identified, their effects on the engine performance quantified and possible solutions to overcome these challenges explored through both theoretical and empirical investigations. This paper intends to provide a comprehensive summary of the implementation issues affecting HCCI combustion in diesel engines.

Engine Performance with Diesel-Biodiesel Blends Fuel and Emission Characteristics

2020 ◽  
Vol 38 (5A) ◽  
pp. 779-788
Author(s):  
Marwa N. Kareem ◽  
Adel M. Salih
Keyword(s):  
Sulfur Content ◽  
Diesel Fuel ◽  
Engine Performance ◽  
Esterification Reaction ◽  
Biodiesel Fuel ◽  
Exhaust Gas ◽  
Gas Temperature ◽  
Biodiesel Blends ◽  
Fuel Blends ◽  
Hc Emissions

In this study, the sunflowers oil was utilized as for producing biodiesel via a chemical operation, which is called trans-esterification reaction. Iraqi diesel fuel suffers from high sulfur content, which makes it one of the worst fuels in the world. This study is an attempt to improve the fuel specifications by reducing the sulfur content of the addition of biodiesel fuel to diesel where this fuel is free of sulfur and has a thermal energy that approaches to diesel.20%, 30% and 50% of Biodiesel fuel were added to the conventional diesel. Performance tests and pollutants of a four-stroke single-cylinder diesel engine were performed. The results indicated that the brake thermal efficiency a decreased by (4%, 16%, and 22%) for the B20, B30 and B50, respectively. The increase in specific fuel consumption was (60%, 33%, and 11%) for the B50, B30, and B20 fuels, respectively for the used fuel blends compared to neat diesel fuel. The engine exhaust gas emissions measures manifested a decreased of CO and HC were CO decreased by (13%), (39%) and (52%), and the HC emissions were lower by (6.3%), (32%), and (46%) for B20, B30 and B50 respectively, compared to diesel fuel. The reduction of exhaust gas temperature was (7%), (14%), and (32%) for B20, B30 and B50 respectively. The NOx emission increased with the increase in biodiesel blends ratio. For B50, the raise was (29.5%) in comparison with diesel fuel while for B30 and B20, the raise in the emissions of NOx was (18%) and...

scholarly journals Thermal Performance of Compression Ignition Engine Using High Content Biodiesels: A Comparative Study with Diesel Fuel

2021 ◽  
Vol 13 (14) ◽  
pp. 7688
Author(s):  
Asif Afzal ◽  
Manzoore Elahi M. Soudagar ◽  
Ali Belhocine ◽  
Mohammed Kareemullah ◽  
Nazia Hossain ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fatty Acid Content ◽  
Engine Performance ◽  
Waste Cooking Oil ◽  
Gas Temperature ◽  
Compression Ignition Engine ◽  
Brake Thermal Efficiency ◽  
Acid Oil ◽  
Exhaust Gas Temperature

In this study, engine performance on thermal factors for different biodiesels has been studied and compared with diesel fuel. Biodiesels were produced from Pongamia pinnata (PP), Calophyllum inophyllum (CI), waste cooking oil (WCO), and acid oil. Depending on their free fatty acid content, they were subjected to the transesterification process to produce biodiesel. The main characterizations of density, calorific range, cloud, pour, flash and fire point followed by the viscosity of obtained biodiesels were conducted and compared with mineral diesel. The characterization results presented benefits near to standard diesel fuel. Then the proposed diesel engine was analyzed using four blends of higher concentrations of B50, B65, B80, and B100 to better substitute fuel for mineral diesel. For each blend, different biodiesels were compared, and the relative best performance of the biodiesel is concluded. This diesel engine was tested in terms of BSFC (brake-specific fuel consumption), BTE (brake thermal efficiency), and EGT (exhaust gas temperature) calculated with the obtained results. The B50 blend of acid oil provided the highest BTE compared to other biodiesels at all loads while B50 blend of WCO provided the lowest BSFC compared to other biodiesels, and B50 blends of all biodiesels provided a minimum % of the increase in EGT compared to diesel.

scholarly journals Improving Blowout Performance of the Conical Swirler Combustor by Employing Two Parts of Fuel at Low Operating Condition

Energies ◽  
2021 ◽  
Vol 14 (6) ◽  
pp. 1681
Author(s):  
Yixiang Yuan ◽  
Qinghua Zeng ◽  
Jun Yao ◽  
Yongjun Zhang ◽  
Mengmeng Zhao ◽  
...  
Keyword(s):  
Distribution Ratio ◽  
Performance Enhancement ◽  
Experimental Testing ◽  
Stability Boundary ◽  
Operating Conditions ◽  
Nox Emission ◽  
Combustion Stability ◽  
Gas Temperature ◽  
Contact Ratio ◽  
Fuel Distribution

Aiming at the problem of the narrow combustion stability boundary, a conical swirler was designed and constructed based on the concept of fuel distribution. The blowout performance was studied at specified low operating conditions by a combination of experimental testing and numerical simulations. Research results indicate that the technique of the fuel distribution can enhance the combustion stability and widen the boundary of flameout within the range of testing conditions. The increase of the fuel distribution ratio improves the combustion stability but leads to an increase in NOx emission simultaneously. The simulation results show the increase of the fuel distribution ratio causes contact ratio increase in the area of lower reference velocity and gas temperature increase. The increased contact ratio and temperature contribute to the blowout performance enhancement, which is identical to the analysis result of the Damkohler number. The reported work in this paper has potential application value for the development of an industrial burner and combustor with high stability and low NOx emission, especially when the combustion system is required to be stable and efficient at low working conditions.

Two-Stroke Marine Diesel Engine Variable Injection Timing System Performance Evaluation and Optimum Setting for Minimum Fuel Consumption at Acceptable NOx Levels

2014 ◽  
Author(s):  
Dimitrios T. Hountalas ◽  
Spiridon Raptotasios ◽  
Antonis Antonopoulos ◽  
Stavros Daniolos ◽  
Iosif Dolaptzis ◽  
...  
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Engine Performance ◽  
Operating Conditions ◽  
Specific Fuel Consumption ◽  
Injection Timing ◽  
Nox Emissions ◽  
Pressure Measurements ◽  
Cylinder Pressure ◽  
Start Of Injection

Currently the most promising solution for marine propulsion is the two-stroke low-speed diesel engine. Start of Injection (SOI) is of significant importance for these engines due to its effect on firing pressure and specific fuel consumption. Therefore these engines are usually equipped with Variable Injection Timing (VIT) systems for variation of SOI with load. Proper operation of these systems is essential for both safe engine operation and performance since they are also used to control peak firing pressure. However, it is rather difficult to evaluate the operation of VIT system and determine the required rack settings for a specific SOI angle without using experimental techniques, which are extremely expensive and time consuming. For this reason in the present work it is examined the use of on-board monitoring and diagnosis techniques to overcome this difficulty. The application is conducted on a commercial vessel equipped with a two-stroke engine from which cylinder pressure measurements were acquired. From the processing of measurements acquired at various operating conditions it is determined the relation between VIT rack position and start of injection angle. This is used to evaluate the VIT system condition and determine the required settings to achieve the desired SOI angle. After VIT system tuning, new measurements were acquired from the processing of which results were derived for various operating parameters, i.e. brake power, specific fuel consumption, heat release rate, start of combustion etc. From the comparative evaluation of results before and after VIT adjustment it is revealed an improvement of specific fuel consumption while firing pressure remains within limits. It is thus revealed that the proposed method has the potential to overcome the disadvantages of purely experimental trial and error methods and that its use can result to fuel saving with minimum effort and time. To evaluate the corresponding effect on NOx emissions, as required by Marpol Annex-VI regulation a theoretical investigation is conducted using a multi-zone combustion model. Shop-test and NOx-file data are used to evaluate its ability to predict engine performance and NOx emissions before conducting the investigation. Moreover, the results derived from the on-board cylinder pressure measurements, after VIT system tuning, are used to evaluate the model’s ability to predict the effect of SOI variation on engine performance. Then the simulation model is applied to estimate the impact of SOI advance on NOx emissions. As revealed NOx emissions remain within limits despite the SOI variation (increase).

Effect of Manufacturing Variability on Turbine Engine Performance: A Probabilistic Study

2013 ◽  
Author(s):  
Michael Gorelik ◽  
Jacob Obayomi ◽  
Jack Slovisky ◽  
Dan Frias ◽  
Howie Swanson ◽  
...  
Keyword(s):  
Performance Metrics ◽  
Model Development ◽  
Engine Performance ◽  
Performance Model ◽  
Probabilistic Methods ◽  
System Level ◽  
Turbine Engine ◽  
Probabilistic Study ◽  
Blade Geometry

While turbine engine Original Equipment Manufacturers (OEMs) accumulated significant experience in the application of probabilistic methods (PM) and uncertainty quantification (UQ) methods to specific technical disciplines and engine components, experience with system-level PM applications has been limited. To demonstrate the feasibility and benefits of an integrated PM-based system, a numerical case study has been developed around the Honeywell turbine engine application. The case study uses experimental observations of engine performance such as horsepower and fuel flow from a population of engines. Due to manufacturing variability, there are unit-to-unit and supplier-to-supplier variations in compressor blade geometry. Blade inspection data are available for the characterization of these geometric variations, and CFD analysis can be linked to the engine performance model, so that the effect of blade geometry variation on system-level performance characteristics can be quantified. Other elements of the case study included the use of engine performance and blade geometry data to perform Bayesian updating of the model inputs, such as efficiency adders and turbine tip clearances. A probabilistic engine performance model was developed, system-level sensitivity analysis performed, and the predicted distribution of engine performance metrics was calibrated against the observed distributions. This paper describes the model development approach and key simulation results. The benefits of using PM and UQ methods in the system-level framework are discussed. This case study was developed under Defense Advanced Research Projects Agency (DARPA) funding which is gratefully acknowledged.

Engine Performance Investigations of Palm Oil, Jatropha Oil and Waste Cooking Oil as Alternative Fuel

2015 ◽  
Vol 1113 ◽  
pp. 674-678
Author(s):  
Syarifah Yunus ◽  
Noriah Yusoff ◽  
Muhammad Faiz Fikri Ahmad Khaidzir ◽  
Siti Khadijah Alias ◽  
Freddawati Rashiddy Wong ◽  
...  
Keyword(s):  
Palm Oil ◽  
Engine Performance ◽  
Alternative Fuel ◽  
Waste Cooking Oil ◽  
Biodiesel Production ◽  
Gas Temperature ◽  
Performance Effect ◽  
Cooking Oil ◽  
Exhaust Gas Temperature ◽  
Global Agenda

The continued using of petroleum energy as a sourced for fuel is widely recognized as unsustainable because of the decreasing of supplies while increasing of the demand. Therefore, it becomes a global agenda to develop a renewable, sustainable and alternative fuel to meets with all the demand. Thus, biodiesel seems to be one of the best choices. In Malaysia, the biodiesel used is from edible vegetable oil sources; palm oil. The uses of palm oil as biodiesel production source have been concern because of the competition with food materials. In this study, various types of biodiesel feedstock are being studied and compared with diesel. The purpose of this comparison is to obtain the optimum engine performance of these different types of biodiesel (edible, non-edible, waste cooking oil) on which are more suitable to be used as alternative fuel. The optimum engine performance effect can be obtains by considering the Brake Power (BP), Specific Fuel Consumption (SFC), Exhaust Gas Temperature (EGT) and Brake Thermal Efficiency (BTE).

A NOx Reduction Project for a GT11 Type Gas Turbine

2005 ◽  
Author(s):  
Lars O. Nord ◽  
David R. Schoemaker ◽  
Helmer G. Andersen
Keyword(s):  
Power Plant ◽  
Distribution System ◽  
Gas Turbines ◽  
Nox Reduction ◽  
Measurement Data ◽  
Combustion Stability ◽  
Study Phase ◽  
Nox Emissions ◽  
Ambient Conditions ◽  
Exhaust Temperature

A study was initiated to investigate the possibility of significantly reducing the NOx emissions at a power plant utilizing, among other manufacturers, ALSTOM GT11 type gas turbines. This study is limited to one of the GT11 type gas turbines on the site. After the initial study phase, the project moved on to a mechanical implementation stage, followed by thorough testing and tuning. The NOx emissions were to be reduced at all ambient conditions, but particularly at cold conditions (below 0°C) where a NOx reduction of more than 70% was the goal. The geographical location of the power plant means cold ambient conditions for a large part of the year. The mechanical modifications included the addition of Helmholtz damper capacity with an approximately 30% increase in volume for passive thermo-acoustic instability control, significant piping changes to the fuel distribution system in order to change the burner configuration, and installation of manual valves for throttling of the fuel gas to individual burners. Subsequent to the mechanical modifications, significant time was spent on testing and tuning of the unit to achieve the wanted NOx emissions throughout a major part of the load range. The tuning was, in addition to the main focus of the NOx reduction, also focused on exhaust temperature spread, combustion stability, CO emissions, as well as other parameters. The measurement data was acquired through a combination of existing unit instrumentation and specific instrumentation added to aid in the tuning effort. The existing instrumentation readings were polled from the control system. The majority of the added instrumentation was acquired via the FieldPoint system from National Instruments. The ALSTOM AMODIS plant-monitoring system was used for acquisition and analysis of all the data from the various sources. The project was, in the end, a success with low NOx emissions at part load and full load. As a final stage of the project, the CO emissions were also optimized resulting in a nice compromise between the important parameters monitored, namely NOx emissions, CO emissions, combustion stability, and exhaust temperature distribution.

A New Approach for Ignition Timing Correction in Spark Ignition Engines Based on Cylinder Tendency to Surface Ignition

2016 ◽  
Vol 819 ◽  
pp. 272-276 ◽  
Author(s):  
Ali Ghanaati ◽  
Mohd Farid Muhamad Said ◽  
Intan Zaurah Mat Darus ◽  
Amin Mahmoudzadeh Andwari
Keyword(s):  
Spark Ignition ◽  
Combustion Stability ◽  
Spark Ignition Engines ◽  
Gas Temperature ◽  
New Approach ◽  
Surface Ignition ◽  
Spark Plug ◽  
Engine Combustion ◽  
Si Engines ◽  
Exhaust Gas Temperature

The performance of Spark Ignition (SI) engines in terms of thermal efficiency can be restricted by knock. Although it is common for all SI engines to exhibit knock from compressed end-gas, knocks from surface ignition remains a more serious problem due to its effect on combustion stability and its obscurity to detect. This paper focuses on predicting the occurrence of knocks from surface ignition by monitoring exhaust gas temperature (EGT). EGT measured during an engine cycle without the spark plug firing. Therefore, EGT rises illustrated any combustion made by surface ignition. Modelling and simulation of a one-dimensional engine combustion done by using GT-Power. The new approach reduces the complexity as EGT monitoring does not require high computational demands, and the EGT signals are robust to noise. The method is validated against a variety of fuel properties and across engine conditions. A new approach is proposed as a measure to predict and detect the knock events.

Sign in / Sign up

Export Citation Format

Share Document