An Experimental Investigation of Hydrogen Fumigation in a Small Direct-Injection Diesel Engine During Part-Load Operation

2011 ◽  
Author(s):  
William E. Marin ◽  
Daniel P. Wiese ◽  
Paul A. Erickson
Keyword(s):  
Diesel Engine ◽  
Flow Rate ◽  
Thermal Efficiency ◽  
Direct Injection ◽  
Low Energy ◽  
Injection Timing ◽  
Effective Pressure ◽  
Cylinder Pressure ◽  
Indicated Mean Effective Pressure ◽  
Hydrogen Enrichment

Hydrogen enrichment may offer enhanced performance of internal combustion engines. Hydrogen’s high specific energy, wide flammability limits, and high flame speed are all desirable traits that can potentially enhance combustion. However, hydrogen’s low energy density and its need to be produced from another energy source pose significant challenges for implementation. Hydrogen enrichment involves co-firing of hydrogen and another primary fuel. The hydrogen can be aspirated through the intake manifold via fumigation or injected at the port or cylinder with the primary fuel. The effect of hydrogen fumigation in diesel engines has been studied to some degree but is not fully understood. In this research, a single-cylinder four-stroke direct-injection diesel engine was modified for hydrogen fumigation and was instrumented to monitor combustion related performance parameters. This engine is representative of low-cost systems that are widely used in developing nations for agricultural and other low power applications. A factorial design of experiments was implemented to study the effects and interactions of hydrogen fumigation flow rate, injection timing, and diesel fuel flow rate on part-load engine performance. At relatively low energy fractions, hydrogen was found to have statistically insignificant effects on brake torque and indicated mean effective pressure, leading to modest decreases in brake thermal efficiency. Exhaust gas temperature increased with hydrogen enrichment. The coefficient of variance of indicated mean effective pressure decreased with hydrogen enrichment, and visible changes to the in-cylinder pressure trace were observed, particularly when injection timing was retarded. The results of this investigation show that for this specific configuration, hydrogen enrichment is not beneficial to the combustion process. The marginal improvements in coefficient of variance and changes of in-cylinder pressure cannot justify the decrease in thermal efficiency of the engine.

Evaluation of the combustion-induced noise and vibration using coherence and wavelet coherence estimates in a diesel engine

2019 ◽  
pp. 146808741987854
Author(s):  
Hossein Ahmadian ◽  
Gholamhassan Najafi ◽  
Barat Ghobadian ◽  
Seyed Reza Hassan-Beygi ◽  
Seyed Salar Hoseini
Keyword(s):  
Diesel Engine ◽  
Sound Pressure ◽  
Fuel Injection ◽  
Direct Injection ◽  
Wavelet Coherence ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Noise And Vibration ◽  
Four Levels ◽  
Wavelet Coherency

The understanding of noise generation and source identification is vital in noise control. This research was conducted to experimentally evaluate combustion-induced noise and vibration using coherence and wavelet coherence estimates. A single-cylinder direct-injection diesel engine was chosen for experimental investigation. The independent variables for conducting experiments were injection timing with five levels of 22, 27, 32 (normal), 37, and 42 crank angles before the top dead center, and also the engine torque load with four levels of 55%, 70%, 85%, and 100% of the rated value. The signals of cylinder pressure, liner acceleration, and radiated sound pressure of the test engine were measured and recorded. Then, coherency and wavelet coherency experiments were carried out between cylinder pressure and liner acceleration, cylinder pressure and sound pressure, and liner acceleration and sound pressure signals in MATLAB software. The results indicated that increasing load would increase wavelet coherency between cylinder pressure and liner acceleration signals at frequencies higher than 1 kHz. The coherent regions between cylinder pressure and sound pressure signals were mainly at frequencies higher than 1 kHz while advancing the fuel injection timing had shifted the coherency toward lower frequencies. In general, with advancing injection timing, the coherent regions between liner acceleration and sound pressure signals have appeared at broader time ranges, especially at frequencies between 100 and 500 Hz. Comparing the results of the wavelet coherency and coherency tests, we concluded that wavelet coherency is a more accurate and descriptive tool in evaluating the combustion-induced noise and vibration.

A Numerical Study of NOx Reduction for a DI Diesel Engine With Complex Geometry

2004 ◽  
Vol 126 (1) ◽  
pp. 13-20 ◽  
Author(s):  
Renshan Liu ◽  
Chao Zhang
Keyword(s):  
Diesel Engine ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Complex Geometry ◽  
Numerical Study ◽  
Direct Injection ◽  
Nox Reduction ◽  
Geometrical Parameters ◽  
Injection Timing ◽  
Di Diesel Engine

A numerical study of NOx reduction for a Direct Injection (DI) Diesel engine with complex geometry, which includes intake/exhaust ports and moving valves, was carried out using the commercial computational fluid dynamics software KIVA-3v. The numerical simulations were conducted to investigate the effects of engine operating and geometrical parameters, including fuel injection timing, fuel injection duration, and piston bowl depth, on the NOx formation and the thermal efficiency of the DI Diesel engine. The tradeoff relationships between the reduction in NOx and the decrease in thermal efficiency were established.

Factors Affecting Performance of Dual Fuel Compression Ignition Engines

2013 ◽  
Vol 388 ◽  
pp. 217-222
Author(s):  
Mohamed Mustafa Ali ◽  
Sabir Mohamed Salih
Keyword(s):  
Diesel Engine ◽  
Fuel Consumption ◽  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection System ◽  
Dual Fuel ◽  
Injection Timing ◽  
Compression Ignition ◽  
Factors Affecting

Compression Ignition Diesel Engine use Diesel as conventional fuel. This has proven to be the most economical source of prime mover in medium and heavy duty loads for both stationary and mobile applications. Performance enhancements have been implemented to optimize fuel consumption and increase thermal efficiency as well as lowering exhaust emissions on these engines. Recently dual fueling of Diesel engines has been found one of the means to achieve these goals. Different types of fuels are tried to displace some of the diesel fuel consumption. This study is made to identify the most favorable conditions for dual fuel mode of operation using Diesel as main fuel and Gasoline as a combustion improver. A single cylinder naturally aspirated air cooled 0.4 liter direct injection diesel engine is used. Diesel is injected by the normal fuel injection system, while Gasoline is carbureted with air using a simple single jet carburetor mounted at the air intake. The engine has been operated at constant speed of 3000 rpm and the load was varied. Different Gasoline to air mixture strengths investigated, and diesel injection timing is also varied. The optimum setting of the engine has been defined which increased the thermal efficiency, reduced the NOx % and HC%.

Effect of Injection Parameters and Strategy on the Noise From a Single Cylinder Direct Injection Diesel Engine

2011 ◽  
Author(s):  
Sukhbir Singh Khaira ◽  
Amandeep Singh ◽  
Marcis Jansons
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Injection Pressure ◽  
Combustion Noise ◽  
Injection Timing ◽  
Cylinder Pressure ◽  
Frequency Spectra ◽  
Single Cylinder ◽  
Direct Injection Diesel Engine ◽  
Injection Parameters

Acoustic noise emitted by a diesel engine generally exceeds that produced by its spark-ignited equivalent and may hinder the acceptance of this more efficient engine type in the passenger car market (1). This work characterizes the combustion noise from a single-cylinder direct-injection diesel engine and examines the degree to which it may be minimized by optimal choice of injection parameters. The relative contribution of motoring, combustion and resonance components to overall engine noise are determined by decomposition of in-cylinder pressure traces over a range of load, injection pressure and start of injection. The frequency spectra of microphone signals recorded external to the engine are correlated with those of in-cylinder pressure traces. Short Time Fourier Transformation (STFT) is applied to cylinder pressure traces to reveal the occurrence of motoring, combustion noise and resonance in the frequency domain over the course of the engine cycle. Loudness is found to increase with enhanced resonance, in proportion to the rate of cylinder pressure rise and under conditions of high injection pressure, load and advanced injection timing.

An investigation for reducing combustion instability under cold-start condition of a direct injection gasoline engine

2018 ◽  
Vol 20 (4) ◽  
pp. 470-479 ◽  
Author(s):  
Koshiro Kimura ◽  
Sachio Mori ◽  
Masato Kawauchi ◽  
Rio Shimizu
Keyword(s):  
Flame Propagation ◽  
Equivalence Ratio ◽  
Direct Injection ◽  
Cold Start ◽  
Spark Ignition Engine ◽  
Injection Timing ◽  
Effective Pressure ◽  
Indicated Mean Effective Pressure ◽  
The Mean ◽  
Initial Flame

In order to meet recent stringent emission regulations, the exhaust catalyst should be heated as early as possible to activate the purifying reactions. In a direct injection spark-ignition engine, a combination of late fuel injection during the compression stroke and late ignition in the expansion stroke is a common strategy to quickly raise exhaust gas temperature for subsequent rapid activation of exhaust catalysts. However, this approach under cold start-up of an engine often results in incomplete and unstable combustion. In this study, to explore the conditions of stable ignition and combustion, the effect of injection timing on indicated mean effective pressure and early combustion duration (MBD0.5) are first investigated by an analysis of the pressure indicator diagram. As this analysis shows a strong correlation between indicated mean effective pressure and MBD0.5, the mechanism of initial flame propagation is investigated intensively using optical diagnostics. Namely, mean equivalence ratio of mixtures in the propagating flame front is measured by focusing on the ratio of C2* to CH* emission intensities. The flow velocity and turbulence intensity around the spark electrode are measured by the back-scattering laser Doppler anemometry. Two major conclusions are derived from this study: First, when the injection timing is retarded, the mean equivalence ratio increases as the time for the injected fuel to travel and diffuse is shortened. The most preferable mean equivalence ratio for fast initial combustion is found to lie in a range from 1.2 to 1.4. Second, when the second injection timing is retarded further, the mean equivalence ratio increases exceeding 1.4, and this results in slower and more fluctuated initial flame propagation. But, if the turbulent intensity is increased by means of the spray induced air motion, the slowed initial combustion can be recovered.

Effects of hydrogen flow rate, injection pressure and EGR on performance of common rail direct injection (CRDi) engine in dual fuel mode

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
S.V. Khandal ◽  
T.M. Yunus Khan ◽  
Sarfaraz Kamangar ◽  
Maughal Ahmed Ali Baig ◽  
Salman Ahmed N J
Keyword(s):  
Diesel Engine ◽  
Flow Rate ◽  
Fuel Injection ◽  
Direct Injection ◽  
Injection Pressure ◽  
Dual Fuel ◽  
Injection Timing ◽  
Oxides Of Nitrogen ◽  
Content Type ◽  
Hydrogen Flow

PurposeThe different performance tests were conducted on diesel engine compression ignition (CI) mode and CRDi engine.Design/methodology/approachThe CI engine was suitably modified to CRDi engine with Toroidal re-entrant combustion chamber (TRCC) and was run in dual-fuel (DF) mode. Hydrogen (H2) was supplied at different flow rates during the suction stroke, and 0.22 Kg/h of hydrogen fuel flow rate (HFFR) was found to be optimum. Diesel and biodiesel were used as pilot fuels. The CRDi engine with DF mode was run at various injection pressures, and 900 bar was found to be optimum injection pressure (IP) with 10o before top dead center (bTDC) as fuel injection timing (IT).FindingsThese operating engine conditions increased formation of oxides of nitrogen (NOx), which were reduced by exhaust gas recycle (EGR). With EGR of 15%, CRDi engine resulted in 12.6% lower brake thermal efficiency (BTE), 5.5% lower hydrocarbon (HC), 7.7% lower carbon monoxide (CO), 26% lower NOx at 80% load as compared to the unmodified diesel engine (CI mode).Originality/valueThe current research is an effort to study and evaluate the performance of CRDi engine in DF mode with diesel-H2 and BCPO-H2 fuel combinations with TRCC.

scholarly journals Effect of diesel-biodiesel-ethanol blend on combustion, performance, and emissions characteristics on a direct injection diesel engine

2017 ◽  
Vol 21 (1 Part B) ◽  
pp. 591-604 ◽  
Author(s):  
Arkadiusz Jamrozik ◽  
Wojciech Tutak ◽  
Michał Pyrc ◽  
Michał Sobiepański
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Biodiesel Fuel ◽  
Effective Pressure ◽  
Ethanol Fuel ◽  
Fuel Blend ◽  
Full Load ◽  
Direct Injection Diesel Engine ◽  
Indicated Mean Effective Pressure ◽  
Partial Load

The paper presents results of co-combustion of diesel-biodiesel-ethanol fuel blend in direct injection Diesel engine. Test was performed at constant rotational speed at three commonly used loads of this engine: 100%, 85%, and 70% of load. During the test hydrated ethanol was used at a concentration of 89% of alcohol. In this study, the ethanol fuel was added to diesel-biodiesel fuel blend with concentrations up to 50% with the increment of 5%. The biodiesel was used as an additive to pre-vent the stratification of ethanol and diesel blends. Thermodynamic parameters of engine were analyzed, and combustion process and exhaust emission were characterized. It turned out that with the increase in engine load is possible to utilize larger ethanol fraction in blend. With the increase of ethanol fuel in blend the in-crease in ignition delay (38.5% for full load) was observed, but burning duration decreased (49% for full load). The ethanol fuel share in blend generally causes the increase in NOx emission (42% for full load) due to higher oxygen content and higher in-cylinder temperatures. It turned out that, at full load the unrepeatability of indicated mean effective pressure was near the same up to 50% of ethanol fuel in blend (about 2%). In case of partial load at higher ethanol fuel fraction the in-crease in indicated mean effective pressure un-repeatability was observed.

Preliminary Investigation of Direct Injection Neat n-Butanol in a Diesel Engine

2014 ◽  
Vol 137 (1) ◽  
Author(s):  
Tadanori Yanai ◽  
Xiaoye Han ◽  
Graham T. Reader ◽  
Ming Zheng ◽  
Jimi Tjong
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Preliminary Investigation ◽  
Pressure Rise ◽  
Engine Performance ◽  
Injection Pressure ◽  
Injection Timing ◽  
Boost Pressure ◽  
Indicated Mean Effective Pressure ◽  
Rise Rate

The characteristics of combustion, emissions, and thermal efficiency of a diesel engine with direct injection (DI) neat n-butanol were investigated. The engine ran at a load of 6.5–8.0 bar indicated mean effective pressure (IMEP) at 1500 rpm engine speed and the injection pressure was controlled to 900 bar. The intake boost pressure, injection timing, and EGR rate were adjusted to investigate the engine performance. The tests demonstrated that neat n-butanol had the potential to achieve ultralow emissions. However, challenges related to reducing the pressure rise rate and improving the ignition controllability were identified.

scholarly journals An analytical and experimental study of performance on jatropha biodiesel engine

2009 ◽  
Vol 13 (3) ◽  
pp. 69-82 ◽  
Author(s):  
Thirunavukkarasu Ganapathy ◽  
Parkash Gakkhar ◽  
Krishnan Murugesan
Keyword(s):  
Diesel Engine ◽  
Thermodynamic Model ◽  
Direct Injection ◽  
Experimental Studies ◽  
Engine Performance ◽  
Performance Characteristics ◽  
Injection Timing ◽  
Engine Fuel ◽  
Cylinder Pressure ◽  
Promising Alternative

Biodiesel plays a major role as one of the alternative fuel options in direct injection diesel engines for more than a decade. Though many feed stocks are employed for making biodiesel worldwide, biodiesel derived from domestically available non-edible feed stocks such as Jatropha curcas L. is the most promising alternative engine fuel option especially in developing countries. Since experimental analysis of the engine is pricey as well as more time consuming and laborious, a theoretical thermodynamic model is necessary to analyze the performance characteristics of jatropha biodiesel fueled diesel engine. There were many experimental studies of jatropha biodiesel fueled diesel engine reported in the literature, yet theoretical study of this biodiesel run diesel engine is scarce. This work presents a theoretical thermodynamic study of single cylinder four stroke direct injection diesel engine fueled with biodiesel derived from jatropha oil. The two zone thermodynamic model developed in the present study computes the in-cylinder pressure and temperature histories in addition to various performance parameters. The results of the model are validated with experimental values for a reasonable agreement. The variation of cylinder pressure with crank angle for various models are also compared and presented. The effects of injection timing, relative air fuel ratio and compression ratio on the engine performance characteristics for diesel and jatropha biodiesel fuels are then investigated and presented in the paper.

scholarly journals Effects of pilot injection timing and EGR on a modern V6 common rail direct injection diesel engine

2013 ◽  
Vol 50 ◽  
pp. 012008 ◽  
Author(s):  
Nik Rosli Abdullah ◽  
Rizalman Mamat ◽  
Miroslaw L Wyszynski ◽  
Anthanasios Tsolakis ◽  
Hongming Xu
Keyword(s):  
Diesel Engine ◽  
Direct Injection ◽  
Common Rail ◽  
Injection Timing ◽  
Pilot Injection ◽  
Direct Injection Diesel Engine
Sign in / Sign up

Export Citation Format

Share Document