Reduction of Emissions From a High Speed Passenger Ferry

2004 ◽  
Author(s):  
Gregory J. Thompson ◽  
Nigel N. Clark ◽  
Mridul Gautam ◽  
Daniel K. Carder ◽  
Sam George
Keyword(s):  
Diesel Fuel ◽  
High Speed ◽  
Water Injection ◽  
Airflow Rate ◽  
Oxides Of Nitrogen ◽  
Redundant Data ◽  
Marine Diesel ◽  
Shaft Torque ◽  
Marine Vessels ◽  
Passenger Ferry

Emissions from marine vessels are being scrutinized as a major contributor to the total particulate matter (TPM), oxides of sulfur (SOx), and oxides of nitrogen (NOx) environmental loading. Fuel sulfur control is the key to SOx reduction but NOx and PM production are primarily engine design dependent. Significant reductions in the emissions from on-road vehicles have been achieved in the last decade and emissions from these vehicles will be reduced by another order of magnitude in the next five years. These improvements have served to emphasize the need to reduce emissions from other mobile sources, including off-road equipment, locomotives, and marine vessels. Diesel-powered vessels of interest include ocean-going vessels with low- and medium-speed engines, as well as smaller vessels with medium- and high-speed engines. A recent study examined to use of intake water injection (WIS) and ultra low sulfur diesel (ULSD) fuel to reduce the emissions from a high-speed passenger ferry in southern California. One of the four Detroit Diesel 12V92 two-stroke, high-speed engines that power the ferry was instrumented to collect intake airflow rate, fuel flow rate, shaft torque, and shaft speed. Engine speed and shaft torque were uniquely linked for given vessel draft and prevailing wind and sea conditions. A raw exhaust gas sampling system was utilized to measure the concentration of NOx, carbon dioxide (CO2), and oxygen (O2), with a mini dilution tunnel sampling a slipstream from the raw exhaust was used to collect TPM on 70 mm filters. The emissions data were processed to yield brake-specific mass results. The emissions measurement system that was employed allowed for redundant data to be collected for quality assurance and quality control. To acquire the data, the ferry was operated at five different steady-state speeds. Three modes were executed in the open sea off Oceanside, CA, idle and harbor modes were also selected for the test matrix. Data have showed that the use of ULSD along with water injection (WIS) could significantly reduce the emissions of NOx and PM while not affecting fuel consumption or engine performance, when compared to baseline marine diesel fuel. The results showed that a normal 40% reduction in TPM was realized when switching from marine diesel fuel to ULSD. A small reduction in NOx was also shown between the marine fuel and the ULSD. The implementation of the WIS reduced NOx by 11% to 17%, depending upon the operating condition. With the WIS, TPM was reduced by a few percentage points, which was close to the confidence level of the measurements.

Diesel Engine NOx Reduction Using Charge Air Water Injection

2005 ◽  
Author(s):  
Ernst Radloff ◽  
Charles Gautier
Keyword(s):  
Fuel Consumption ◽  
Nox Reduction ◽  
Water Injection ◽  
Fuel Oil ◽  
Emissions Reduction ◽  
Nox Emissions ◽  
Test Results ◽  
Marine Diesel ◽  
Marine Vessels ◽  
The Impact

The Transportation Development Centre of Transport Canada, in collaboration with Environment Canada’s Emissions Research and Measurement Division, conducted a series of emissions tests onboard the Oceanex RoRo vessel MV Cabot operating between Montre´al, Quebec, and St. John’s, Newfoundland. The primary objectives were to verify emissions inventories and demonstrate the feasibility of installing affordable emissions reduction technology on marine vessels as well as compliance with future regulatory emissions limits. The tests also provided an opportunity for Canada to share information on emissions program and technology developments with U.S. regulatory authorities. This may lead to developing joint emissions reduction initiatives for existing marine vessels. This paper describes the field-testing of a water injection system (WIS) to reduce oxides of nitrogen (NOx) emissions from ocean-going vessels. Tests were conducted on a semi-dedicated basis during voyage and under steady-state conditions. The emissions measurements were taken in accordance with ISO 8178-4-E3 protocol and using both marine diesel oil and intermediate fuel oil, which enabled the evaluation of the impact of different fuel type and quality on emissions. An initial series of tests was carried out on the MV Cabot in March 2004, followed by a second series of tests on the same vessel in March 2005. These tests demonstrated the effectiveness of a low-cost WIS for reducing NOx emissions in marine diesel engines. They also showed that water injection reduces NOx at the expense of an increase in both particulate matter and carbon monoxide when using intermediate fuel oil. NOx reductions varied between 10 and 35 percent, and were most effective at high water injection ratios above 50 percent engine load. The test results showed no negative impact of the WIS on fuel consumption or engine operation and performance. This paper compares the results obtained from the consecutive series of tests in terms of the effectiveness of NOx reduction, and analyses the results in the context of other full-scale test results obtained from emissions control system vendors and engine suppliers. It also investigates the theoretical process and technology of water injection through charge air fumigation, and both direct water and fuel/water emulsion injection. In addition, the effects of water injection on engine emissions, operation and maintenance, and the optimization of water injection from a knowledge-based perspective are discussed. Further testing and development of the WIS are required to realize optimal emissions reduction potential and to determine the impact of water injection on fuel consumption, and engine operational performance as well as the impact of fuel quality on emissions.

STUDI PENENTUAN KOMPOSISI OPTIMUM CAMPURAN BAHAN BAKAR BIODIESEL–PETRODIESEL

2018 ◽  
Vol 4 (2) ◽  
Author(s):  
Soni S. Wirawan dkk
Keyword(s):  
Carbon Monoxide ◽  
Particulate Matter ◽  
Diesel Engine ◽  
Fuel Consumption ◽  
Diesel Fuel ◽  
Cetane Number ◽  
Price Policy ◽  
Oxides Of Nitrogen ◽  
Fuel Price ◽  
Biodiesel Blend

Biodiesel is a viable substitute for petroleum-based diesel fuel. Its advantages are improved lubricity, higher cetane number and cleaner emission. Biodiesel and its blends with petroleum-based diesel fuel can be used in diesel engines without any signifi cant modifi cations to the engines. Data from the numerous research reports and test programs showed that as the percent of biodiesel in blends increases, emission of hydrocarbons (HC), carbon monoxide (CO), and particulate matter (PM) all decrease, but the amount of oxides of nitrogen (NOx) and fuel consumption is tend to increase. The most signifi cant hurdle for broader commercialization of biodiesel is its cost. In current fuel price policy in Indonesia (especially fuel for transportation), the higher percent of biodiesel in blend will increase the price of blends fuel. The objective of this study is to assess the optimum blends of biodiesel with petroleum-based diesel fuel from the technically and economically consideration. The study result recommends that 20% biodiesel blend with 80% petroleum-based diesel fuel (B20) is the optimum blend for unmodifi ed diesel engine uses.Keywords: biodiesel, emission, optimum, blend

Characteristics of injection of diesel fuel, rapeseed oil and their mixtures in diesel engines of various types

2021 ◽  
pp. 167-178
Author(s):  
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Diesel Engines ◽  
Rapeseed Oil ◽  
High Speed ◽  
Fuel Injection ◽  
Experimental Studies ◽  
Fuel Injector ◽  
High Speed Diesel ◽  
Engine Type

The necessity of adapting diesel engines to work on vegetable oils is justified. The possibility of using rapeseed oil and its mixtures with petroleum diesel fuel as motor fuels is considered. Experimental studies of fuel injection of small high-speed diesel engine type MD-6 (1 Ch 8,0/7,5)when using diesel oil and rapeseed oil and computational studies of auto-tractor diesel engine type D-245.12 (1 ChN 11/12,5), working on blends of petroleum diesel fuel and rapeseed oil. When switching autotractor diesel engine from diesel fuel to rapeseed oil in the full-fuel mode, the mass cycle fuel supply increased by 12 %, and in the small-size high-speed diesel engine – by about 27 %. From the point of view of the flow of the working process of these diesel engines, changes in other parameters of the fuel injection process are less significant. Keywords diesel engine; petroleum diesel fuel; vegetable oil; rapeseed oil; high pressure fuel pump; fuel injector; sprayer

scholarly journals DESIGN OF A MOBILE BIO-DIESEL PRODUCTION FACILITY

2011 ◽  
Author(s):  
B. J. Drake ◽  
M. Jacques ◽  
D. Binkley ◽  
S. Barghi ◽  
R. O. Buchal
Keyword(s):  
Particulate Matter ◽  
Vegetable Oil ◽  
Diesel Fuel ◽  
High Speed ◽  
Solid Particles ◽  
Vacuum Filter ◽  
Production Facility ◽  
Operational Life ◽  
Used Vegetable Oil ◽  
Diesel Production

In 2004/2005, a team of mechanical engineering students undertook an interdisciplinary capstone design project to design a mobile bio-diesel production facility capable of converting 500 L/h of used vegetable oil or animal tallow into bio-diesel fuel. Bio-diesel fuel has negligible sulfur content and significantly reduces the emission of particulate matter, e.g. soot and carbon monoxide, compared to the combustion of conventional diesel fuel. Furthermore, bio-diesel fuel is biodegradable, nontoxic, and can be produced from renewable feedstock. The mobile facility is capable of taking used vegetable oil from different sources and processing the oil while in motion, eliminating costs associated with transportation, land use and construction. A special filter was designed to remove any major particulate matter as well as wax-like substances formed by heating of the cooking oil during its operational life. A rotary vacuum filter was designed to continuously of remove wax and solid particles accumulated on the filter cloth. The wax and solid wastes, which are organic compounds, are readily converted to useful light organic molecules through a subsequent gasification process. A transesterification process was applied using methanol as a solvent and sodium hydroxide as a catalyst. A mix of unrefined bio-diesel fuel and glycerol, which is produced by transestrification, is sent to a glycerol separating tower. The separator was designed to efficiently separate bio-diesel fuel from glycerol. The bio-diesel fuel is neutralized by weak acid solution and washed by water to remove impurities. High-speed mixers were designed to create maximum contact between phases for efficient separation. The mobile facility is subject to vibration, which was considered in every aspect of the design. The facility will be powered by bio-diesel fuel, and heat recovery and water recycling were considered to minimize energy requirements. The project culminated in a final design report containing detailed engineering analysis and a comprehensive set of working drawings.

scholarly journals Effects of Oxygenated Additives with Diesel on the Performance of D I Diesel Engine

2019 ◽  
pp. 1-9 ◽  
Author(s):  
P. Venkateswara Rao ◽  
S. Ramesh ◽  
S. Anil Kumar
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Direct Injection ◽  
Primary Objective ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Smoke Emission ◽  
Oxygenated Additives ◽  
Blend Fuel ◽  
Fuel Formulation

The primary objective of this work is to reduce the particulate matter (PM) or smoke emission and oxides of nitrogen (NOx emissions) the two important harmful emissions and to increase the performance of diesel engine by using oxygenated additives with diesel as blend fuel. Formulation of available diesel fuel with additives is an advantage than considering of engine modification for improvement of higher output. From the available additives, three oxygenates are selected for experimentation by considering many aspects like cost, content of oxygen, flashpoint, solubility, seal etc. The selected oxygenates are Ethyl Aceto Acetate (EAA), Diethyl Carbonate (DEC), Diethylene Glycol (DEG). These oxygenates are blended with diesel fuel in proportions of 2.5%, 5% and 7.5% by volume and experiments were conducted on a single cylinder naturally aspirated direct injection diesel engine. From the results the conclusion are higher brake power and lower BSFC obtained for DEC blends at 7.5% of additive as compared to EAA, DEG and diesel at full load. In case of DEC blends the smoke emission is lower, whereas NOx emissions are very low in case of EAA additive blend fuels. The DEC can be considered is the best oxygenating additive to be blend with diesel in a proportion of 7.5% by volume.

Evaluating the outcomes of a single-cylinder CRDI engine operated by lemon peel oil under the influence of DTBP, rice husk nano additive and water injection

2021 ◽  
pp. 146808742110477
Author(s):  
Mebin Samuel Panithasan ◽  
Gnanamoorthi Venkadesan
Keyword(s):  
Rice Husk ◽  
Diesel Fuel ◽  
Water Injection ◽  
Nox Emission ◽  
Single Cylinder ◽  
Lemon Peel ◽  
Bio Oil ◽  
Butyl Peroxide ◽  
Lemon Peel Oil ◽  
Peel Oil

In the search for an alternative energy source with lesser pollution for transportation needs, bio-oil, a denser and viscous fuel that needs a transesterification process, have been widely considered for diesel engines. However, these problems are solved by using low viscous biofuel, but this improvement also significantly leads to increased NOx emission. Hence this present study investigates the usage of a low viscous biofuel in the CRDI engine with measures to reduce NOx emission through water injection technique. The low viscous bio-oil was used in this study along with an ignition enhancer (di-tert-butyl-peroxide), non-metallic nano additive (rice husk). They were tested in a constant speed, single-cylinder, diesel engine for various loads. Considering the brake thermal efficiency (BTE), 2% and 150 ppm were selected as the optimum value after testing five ratios (1%, 1.5%, 2%, 2.5% and 3%) of di tert butyl peroxide (DTBP) and four ratios (50, 100, 150 and 200 ppm) of rice husk (RH). The lemon peel oil (LPO) with the optimum additive ratio produced 30.69% BTE, which was 4.7% lesser than diesel fuel. A considerable decrease in fuel consumption and emissions except for nitrogen oxides (NOx) is recorded. NOx emission increased by 17.3% for the biofuel blend containing RH and DTBP. To control NOx emission, 2% of water was injected into the intake manifold with the fresh intake air. Two percent by vol. was finalised after experimenting four ratios (1%, 2%, 3% and 4%) of water addition. This 2% water reduces 11% of NOx emission and affects the other outputs, denoted with the 8.9% reduced BTE value compared with diesel fuel. Thus, the LPOC combination proved to operate well in the CRDI engine and produces lower NOx emissions than other LPO blends.

scholarly journals Influence of Fuel Injection Pressure on the Emissions Characteristics and Engine Performance in a CRDI Diesel Engine Fueled with Palm Biodiesel Blends

Energies ◽  
2019 ◽  
Vol 12 (20) ◽  
pp. 3837 ◽  
Author(s):  
Sam Ki Yoon ◽  
Jun Cong Ge ◽  
Nag Jung Choi
Keyword(s):  
Diesel Engine ◽  
Diesel Fuel ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Biodiesel Fuel ◽  
Nox Emissions ◽  
Oxides Of Nitrogen ◽  
Fuel Blend ◽  
Engine Load ◽  
Fuel Injection Pressure

This experiment investigates the combustion and emissions characteristics of a common rail direct injection (CRDI) diesel engine using various blends of pure diesel fuel and palm biodiesel. Fuel injection pressures of 45 and 65 MPa were investigated under engine loads of 50 and 100 Nm. The fuels studied herein were pure diesel fuel 100 vol.% with 0 vol.% of palm biodiesel (PBD0), pure diesel fuel 80 vol.% blended with 20 vol.% of palm biodiesel (PBD20), and pure diesel fuel 50 vol.% blended with 50 vol.% of palm biodiesel (PBD50). As the fuel injection pressure increased from 45 to 65 MPa under all engine loads, the combustion pressure and heat release rate also increased. The indicated mean effective pressure (IMEP) increased with an increase of the fuel injection pressure. In addition, for 50 Nm of the engine load, an increase to the fuel injection pressure resulted in a reduction of the brake specific fuel consumption (BSFC) by an average of 2.43%. In comparison, for an engine load of 100 Nm, an increase in the fuel injection pressure decreased BSFC by an average of 0.8%. Hydrocarbon (HC) and particulate matter (PM) decreased as fuel pressure increased, independent of the engine load. Increasing fuel injection pressure for 50 Nm engine load using PBD0, PBD20 and PBD50 decreased carbon monoxide (CO) emissions. When the fuel injection pressure was increased from 45 MPa to 65 MPa, oxides of nitrogen (NOx) emissions were increased for both engine loads. For a given fuel injection pressure, NOx emissions increased slightly as the biodiesel content in the fuel blend increased.

Sign in / Sign up

Export Citation Format

Share Document