The Impact of Cylinder Pressure on Fuel Jet Penetration and Mixing

2002 ◽  
Author(s):  
Daniel B. Olsen ◽  
Bryan D. Willson
Keyword(s):  
Fuel Injection ◽  
Volume Fraction ◽  
Uv Light ◽  
Visible Range ◽  
Compression Process ◽  
Iccd Camera ◽  
Fuel Concentration ◽  
Fuel Jet ◽  
Jet Penetration ◽  
The Impact

Investigations of fuel jet penetration and fuel and air mixing are performed in a static piston, pressurized optical engine. The pressure in the cylinder that the gas is injected into is varied to study the effect of the compression process. The engine has the same piston and cylinder geometry as a Cooper-Bessemer GMV-4TF two-stroke cycle natural gas engine. A 14” quartz cylinder section allows the cylinder gases to be radiated with an Nd:YAG UV laser, and imaged with an ICCD camera. Nitrogen gas that is seeded with acetone, which fluoresces in the visible range when irradiated with UV light, is injected through the fuel valves. Two types of fuel injectors are studied, a low pressure (45 psi) and a high pressure (500 psi) gas injection valve. Both fuel injection valves are manufactured by Woodward Governor. Planar laser induced fluorescence is implemented to image fuel concentration within the cylinder at various times during the injection and mixing processes. Spatial standard deviations of the variations of fuel concentration (“unmixedness”) and the volume fraction of gas in the flammable range (“mixedness”) across the image plane are computed.

scholarly journals Numerical Treatment of the Interface in Two Phase Flows Using a Compressible Framework in OpenFOAM: Demonstration on a High Velocity Droplet Impact Case

Fluids ◽  
2021 ◽  
Vol 6 (2) ◽  
pp. 78
Author(s):  
Giovanni Tretola ◽  
Konstantina Vogiatzaki
Keyword(s):  
High Velocity ◽  
Fast Moving ◽  
Fuel Injection ◽  
Volume Fraction ◽  
Surface Tension Force ◽  
Considerable Effect ◽  
Mitigation Strategies ◽  
Two Phase ◽  
Droplet Shape ◽  
The Impact

The ability to accurately predict the dynamics of fast moving and deforming interfaces is of interest to a number of applications including ink printing, drug delivery and fuel injection. In the current work we present a new compressible framework within OpenFOAM which incorporates mitigation strategies for the well known issue of spurious currents. The framework incorporates the compressible algebraic Volume-of-Fluid (VoF) method with additional interfacial treatment techniques including volume fraction smoothing and sharpening (for the calculation of the interface geometries and surface tension force, respectively) as well as filtering of the capillary forces. The framework is tested against different benchmarks: A 2D stationary droplet, a high velocity impact droplet case (500 m/s impact velocity) against a dry substrate and, with the same impact conditions, against a liquid film. For the 2D static droplet case, our results are consistent with what is observed in the literature when these strategies are implemented within incompressible frameworks. For the high impact droplet cases we find that accounting for both compressibility and correct representation of the interface is very important in numerical simulations, since pressure waves develop and propagate within the droplet interacting with the interface. While the implemented strategies do not alter the dynamics of the impact and the droplet shape, they have a considerable effect on the lamella formation. Our numerical method, although currently implemented for droplet cases, can also be used for any fast moving interface with or without considering the impact on a surface.

scholarly journals Nanofluid flow containing carbon nanotubes with quartic autocatalytic chemical reaction and Thompson and Troian slip at the boundary

2020 ◽  
Vol 10 (1) ◽  
Author(s):  
Muhammad Ramzan ◽  
Jae Dong Chung ◽  
Seifedine Kadry ◽  
Yu-Ming Chu ◽  
Muhammad Akhtar
Keyword(s):  
Mathematical Model ◽  
Carbon Nanotubes ◽  
Drag Force ◽  
Chemical Reaction ◽  
Slip Velocity ◽  
Volume Fraction ◽  
Surface Drag ◽  
Nanofluid Flow ◽  
Velocity Parameter ◽  
The Impact

Abstract A mathematical model is envisioned to discourse the impact of Thompson and Troian slip boundary in the carbon nanotubes suspended nanofluid flow near a stagnation point along an expanding/contracting surface. The water is considered as a base fluid and both types of carbon nanotubes i.e., single-wall (SWCNTs) and multi-wall (MWCNTs) are considered. The flow is taken in a Dacry-Forchheimer porous media amalgamated with quartic autocatalysis chemical reaction. Additional impacts added to the novelty of the mathematical model are the heat generation/absorption and buoyancy effect. The dimensionless variables led the envisaged mathematical model to a physical problem. The numerical solution is then found by engaging MATLAB built-in bvp4c function for non-dimensional velocity, temperature, and homogeneous-heterogeneous reactions. The validation of the proposed mathematical model is ascertained by comparing it with a published article in limiting case. An excellent consensus is accomplished in this regard. The behavior of numerous dimensionless flow variables including solid volume fraction, inertia coefficient, velocity ratio parameter, porosity parameter, slip velocity parameter, magnetic parameter, Schmidt number, and strength of homogeneous/heterogeneous reaction parameters are portrayed via graphical illustrations. Computational iterations for surface drag force are tabulated to analyze the impacts at the stretched surface. It is witnessed that the slip velocity parameter enhances the fluid stream velocity and diminishes the surface drag force. Furthermore, the concentration of the nanofluid flow is augmented for higher estimates of quartic autocatalysis chemical.

scholarly journals Low-carbon cast microalloyed steel intercritically heat-treated at different temperatures: microstructure and mechanical properties

2021 ◽  
Vol 21 (2) ◽  
Author(s):  
Hadi Torkamani ◽  
Shahram Raygan ◽  
Carlos Garcia Mateo ◽  
Yahya Palizdar ◽  
Jafar Rassizadehghani ◽  
...  
Keyword(s):  
Carbon Content ◽  
Volume Fraction ◽  
Block Size ◽  
Tensile Tests ◽  
Total Elongation ◽  
Martensite Phase ◽  
Low Carbon ◽  
Steel Increase ◽  
Different Temperatures ◽  
The Impact

AbstractIn this study, dual-phase (DP, ferrite + martensite) microstructures were obtained by performing intercritical heat treatments (IHT) at 750 and 800 °C followed by quenching. Decreasing the IHT temperature from 800 to 750 °C leads to: (i) a decrease in the volume fraction of austenite (martensite after quenching) from 0.68 to 0.36; (ii) ~ 100 °C decrease in martensite start temperature (Ms), mainly due to the higher carbon content of austenite and its smaller grains at 750 °C; (iii) a reduction in the block size of martensite from 1.9 to 1.2 μm as measured by EBSD. Having a higher carbon content and a finer block size, the localized microhardness of martensite islands increases from 380 HV (800 °C) to 504 HV (750 °C). Moreover, despite the different volume fractions of martensite obtained in DP microstructures, the hardness of the steels remained unchanged by changing the IHT temperature (~ 234 to 238 HV). Applying lower IHT temperature (lower fraction of martensite), the impact energy even decreased from 12 to 9 J due to the brittleness of the martensite phase. The results of the tensile tests indicate that by increasing the IHT temperature, the yield and ultimate tensile strengths of the DP steel increase from 493 to 770 MPa, and from 908 to 1080 MPa, respectively, while the total elongation decreases from 9.8 to 4.5%. In contrast to the normalized sample, formation of martensite in the DP steels could eliminate the yield point phenomenon in the tensile curves, as it generates free dislocations in adjacent ferrite.

scholarly journals Lasting effects of prenatal exposure to Cannabis in the retina of the offspring: an experimental study in mice

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Paulo Roberto Arruda Zantut ◽  
Mariana Matera Veras ◽  
Sarah Gomes Menezes Benevenutto ◽  
Angélica Mendonça Vaz Safatle ◽  
Ricardo Augusto Pecora ◽  
...  
Keyword(s):  
Young Adult ◽  
Light Microscopy ◽  
Prenatal Exposure ◽  
Structural Changes ◽  
Volume Fraction ◽  
Clinical Care ◽  
Retinal Layer ◽  
Exposed Population ◽  
The Central Nervous System ◽  
The Impact

Abstract Background Prenatal exposure to Cannabis is a worldwide growing problem. Although retina is part of the central nervous system, the impact of maternal Cannabis use on the retinal development and its postnatal consequences remains unknown. As the prenatal period is potentially sensitive in the normal development of the retina, we hypothesized that recreational use of Cannabis during pregnancy may alter retina structure in the offspring. To test this, we developed a murine model that mimics human exposure in terms of dose and use. Methods Pregnant BalbC mice were exposed daily for 5 min to Cannabis smoke (0.2 g of Cannabis) or filtered air, from gestational day 5 to 18 (N = 10/group). After weaning period, pups were separated and examined weekly. On days 60, 120, 200, and 360 after birth, 10 pups from each group were randomly selected for Spectral Domain Optical Coherence Tomography (SD-OCT) analysis of the retina. All retina layers were measured and inner, outer, and total retina thickness were calculated. Other 37 mice from both groups were sacrificed on days 20, 60, and 360 for retinal stereology (total volume of the retina and volume fraction of each retinal layer) and light microscopy. Means and standard deviations were calculated and MANOVA was performed. Results The retina of animals which mother was exposed to Cannabis during gestation was 17% thinner on day 120 (young adult) than controls (P = 0.003) due to 21% thinning of the outer retina (P = 0.001). The offspring of mice from the exposed group presented thickening of the IS/OS in comparison to controls on day 200 (P < 0.001). In the volumetric analyzes by retinal stereology, the exposed mice presented transitory increase of the IS/OS total volume and volume fraction on day 60 (young adult) compared to controls (P = 0.008 and P = 0.035, respectively). On light microscopy, exposed mice presented thickening of the IS/OS on day 360 (adult) compared to controls (P = 0.03). Conclusion Gestational exposure to Cannabis smoke may cause structural changes in the retina of the offspring that return to normal on mice adulthood. These experimental evidences suggest that children and young adults whose mothers smoked Cannabis during pregnancy may require earlier and more frequent clinical care than the non-exposed population.

scholarly journals Insulation Characteristics of Sisal Fibre/Epoxy Composites

2017 ◽  
Vol 2017 ◽  
pp. 1-6 ◽  
Author(s):  
A. Shalwan ◽  
M. Alajmi ◽  
A. Alajmi
Keyword(s):  
Volume Fraction ◽  
Fibre Volume Fraction ◽  
Thermal Characteristics ◽  
Fibre Volume ◽  
Point Of View ◽  
Natural Fibres ◽  
Epoxy Composites ◽  
Ongoing Research ◽  
Sisal Fibre ◽  
The Impact

Using natural fibres in civil engineering is the aim of many industrial and academics sectors to overcome the impact of synthetic fibres on environments. One of the potential applications of natural fibres composites is to be implemented in insulation components. Thermal behaviour of polymer composites based on natural fibres is recent ongoing research. In this article, thermal characteristics of sisal fibre reinforced epoxy composites are evaluated for treated and untreated fibres considering different volume fractions of 0–30%. The results revealed that the increase in the fibre volume fraction increased the insulation performance of the composites for both treated and untreated fibres. More than 200% insulation rate was achieved at the volume fraction of 20% of treated sisal fibres. Untreated fibres showed about 400% insulation rate; however, it is not recommended to use untreated fibres from mechanical point of view. The results indicated that there is potential of using the developed composites for insulation purposes.

Experimental Model of Temperature-Driven Nanofluid

2006 ◽  
Vol 129 (6) ◽  
pp. 697-704 ◽  
Author(s):  
A. G. Agwu Nnanna
Keyword(s):  
Heat Transfer ◽  
Convective Heat Transfer ◽  
Convective Heat ◽  
Small Volume ◽  
Volume Fraction ◽  
Convective Heat Transfer Coefficient ◽  
Isothermal Condition ◽  
Carrier Fluid ◽  
Small Volume Fraction ◽  
The Impact

This paper presents a systematic experimental method of studying the heat transfer behavior of buoyancy-driven nanofluids. The presence of nanoparticles in buoyancy-driven flows affects the thermophysical properties of the fluid and consequently alters the rate of heat transfer. The focus of this paper is to estimate the range of volume fractions that results in maximum thermal enhancement and the impact of volume fraction on Nusselt number. The test cell for the nanofluid is a two-dimensional rectangular enclosure with differentially heated vertical walls and adiabatic horizontal walls filled with 27 nm Al2O3–H2O nanofluid. Simulations were performed to measure the transient and steady-state thermal response of nanofluid to imposed isothermal condition. The volume fraction is varied between 0% and 8%. It is observed that the trend of the temporal and spatial evolution of temperature profile for the nanofluid mimics that of the carrier fluid. Hence, the behaviors of both fluids are similar. Results shows that for small volume fraction, 0.2⩽ϕ⩽2% the presence of the nanoparticles does not impede the free convective heat transfer, rather it augments the rate of heat transfer. However, for large volume fraction ϕ>2%, the convective heat transfer coefficient declines due to reduction in the Rayleigh number caused by increase in kinematic viscosity. Also, an empirical correlation for Nuϕ as a function of ϕ and Ra has been developed, and it is observed that the nanoparticle enhances heat transfer rate even at a small volume fraction.

Investigation on penetration model of shaped charge jet in water

2016 ◽  
Vol 30 (02) ◽  
pp. 1550268 ◽  
Author(s):  
Jinwei Shi ◽  
Xingbai Luo ◽  
Jinming Li ◽  
Jianwei Jiang
Keyword(s):  
Numerical Simulation ◽  
Theoretical Model ◽  
Model Simulation ◽  
Theoretical Models ◽  
Theoretical Research ◽  
Water Medium ◽  
Simulation Results ◽  
Jet Penetration ◽  
The Impact ◽  
Penetration Velocity

To analyze the process of jet penetration in water medium quantitatively, the properties of jet penetration spaced target with water interlayer were studied through test and numerical simulation. Two theoretical models of jet penetration in water were proposed. The theoretical model 1 was established considering the impact of the shock wave, combined with the shock equation Rankine–Hugoniot and the virtual origin calculation method. The theoretical model 2 was obtained by fitting theoretical analysis and numerical simulation results. The effectiveness and universality of the two theoretical models were compared through the numerical simulation results. Both the models can reflect the relationship between the penetration velocity and the penetration distance in water well, and both the deviation and stability of theoretical model 1 are better than 2, the lower penetration velocity, and the larger deviation of the theoretical model 2. Therefore, the theoretical model 1 can reflect the properties of jet penetration in water effectively, and provide the reference of model simulation and theoretical research.

Reduction of Fuel Utilization Through Oxygen-Enriched Combustion in a Reheat Furnace Pusher-Type

2021 ◽  
Author(s):  
Francisco J. Martinez Zambrano ◽  
Armin K. Silaen ◽  
Kelly Tian ◽  
Joe Maiolo ◽  
Chenn Zhou
Keyword(s):  
Heat Flux ◽  
Fuel Injection ◽  
Combustion Process ◽  
Oxygen Enrichment ◽  
Rolling Temperature ◽  
Heating Zone ◽  
Reheat Furnace ◽  
Steel Slabs ◽  
The Impact ◽  
Reheating Process

Abstract Steelmaking is an energy-intensive process. Thus, energy efficiency is highly important. Several stages of steelmaking involve combustion processes. One of the most energy-consuming processes in steelmaking is the slab reheating process in a reheat furnace (RF). The energy released by fuel combustion is used to heat steel slabs to their proper hot-rolling temperature. The steel slabs move through the reheat furnace passing the three stages of heating called: Preheating Zone (PZ), Heating Zone (HZ), and Soaking Zone (SZ) to finally leave the discharge door at a rolling temperature of 2375 °F. One way to improve a reheat furnace’s fuel consumption is by implementing oxygen-enriched combustion. This study investigates the implementation of oxygen-enriched combustion in a pusher-type reheat furnace. The increment of oxygen in the combustion process allows for increasing the furnace gas temperature. Consequently, the oxygen enrichment approach allows for the reduction of fuel injection. The principal goal of this investigation is to model the combustion-based on oxygen-enrichment and develop parametric studies of fuel injection rates. The different simulations aim to match the slab heat flux profile of the industrial reheat furnace pusher-type. Computational fluid dynamics are used to generate the slab heat flux distribution. To reach more uniform slab heating, oxygen and fuel ports were alternated. Also, injection angles were modified to optimize slab heating and avoid the impact of hot spots. Thermocouple readings of the industrial reheat furnace are compared to simulation results. The results determined that 40–45% fuel reduction can be achieved.

Thermo-Solutal Convection of a Nanofluid Utilizing Fourier’s-Type Compass Conditions

2020 ◽  
Vol 9 (4) ◽  
pp. 362-374
Author(s):  
J. C. Umavathi ◽  
Ali J. Chamkha
Keyword(s):  
Brownian Motion ◽  
Prandtl Number ◽  
Boundary Conditions ◽  
Volume Fraction ◽  
Temperature Fields ◽  
Physical Parameters ◽  
Surface Boundary ◽  
Perturbation Scheme ◽  
Runge Kutta ◽  
The Impact

Nanotechnology has infiltrated into duct design in parallel with many other fields of mechanical, medical and energy engineering. Motivated by the excellent potential of nanofluids, a subset of materials engineered at the nanoscale, in the present work, a new mathematical model is developed for natural convection in a vertical duct containing nanofluid. Numerical scrutiny for the double-diffusive free and forced convection within a duct encumbered with nanofluid is performed. Buongiorno’s model is deployed to define the nanofluid. Robin boundary conditions are used to define the surface boundary conditions. Thermal and concentration equations envisage the viscous, Brownian motion, thermosphores of the nanofluid, Soret and Dufour effects. Using the Boussi-nesq approximation the solutal buoyancy effect as a result of gradients in concentration are incorporated. The conservation equations which are nonlinear are numerically estimated using fourth order Runge-Kutta methodology and analytically ratifying regular perturbation scheme. The mass, heat, nanoparticle concentration and species concentration fields on eight dimensionless physical parameters such as thermal and mass Grashof numbers, Brownian motion parameter, thermal parameter, Prandtl number, Eckert number, Schmidt parameter, and Soret parameter are calculated. The impact of these parameters are outlined pictorially. The velocity and temperature fields are boosted with the thermal Grashof number. The Soret and the Schemidt parameters reduces the nanoparticle volume fraction but it heightens the momentum, temperature and concentration. At the cold wall thermal and concentration Grashof numbers reduces the Nusselt values but they increase the Nusselt values at the hot wall. The reversal consequence was attained at the hot plate. The perturbation and Runge-Kutta solutions are equal in the nonappearance of Prandtl number. The (E. Zanchini, Int. J. Heat Mass Transfer 41, 3949 (1998)). results are restored for the regular fluid. The heat transfer rate is high for nanofluid when matched with regular fluid.

The Effects of Bone Microstructure on Subsidence Risk for ALIF, LLIF, PLIF, and TLIF Spine Cages

2019 ◽  
Vol 141 (3) ◽  
Author(s):  
Vivek Palepu ◽  
Melvin D. Helgeson ◽  
Michael Molyneaux-Francis ◽  
Srinidhi Nagaraja
Keyword(s):  
Trabecular Bone ◽  
Bone Quality ◽  
Volume Fraction ◽  
Lumbar Fusion ◽  
Lumbar Vertebrae ◽  
Micro Ct ◽  
Cage Subsidence ◽  
Maximum Subsidence ◽  
Trabecular Bone Quality ◽  
The Impact

Several approaches (anterior, posterior, lateral, and transforaminal) are used in lumbar fusion surgery. However, it is unclear whether one of these approaches has the greatest subsidence risk as published clinical rates of cage subsidence vary widely (7–70%). Specifically, there is limited data on how a patient's endplate morphometry and trabecular bone quality influences cage subsidence risk. Therefore, this study compared subsidence (stiffness, maximum force, and work) between anterior (ALIF), lateral (LLIF), posterior (PLIF), and transforaminal (TLIF) lumbar interbody fusion cage designs to understand the impact of endplate and trabecular bone quality on subsidence. Forty-eight lumbar vertebrae were imaged with micro-ct to assess trabecular microarchitecture. micro-ct images of each vertebra were then imported into image processing software to measure endplate thickness (ET) and maximum endplate concavity depth (ECD). Generic ALIF, LLIF, PLIF, and TLIF cages made of polyether ether ketone were implanted on the superior endplates of all vertebrae and subsidence testing was performed. The results indicated that TLIF cages had significantly lower (p < 0.01) subsidence stiffness and maximum subsidence force compared to ALIF and LLIF cages. For all cage groups, trabecular bone volume fraction was better correlated with maximum subsidence force compared to ET and concavity depth. These findings highlight the importance of cage design (e.g., surface area), placement on the endplate, and trabecular bone quality on subsidence. These results may help surgeons during cage selection for lumbar fusion procedures to mitigate adverse events such as cage subsidence.

Sign in / Sign up

Export Citation Format

Share Document