Optimization of Single Row Jet Impingement Array by Varying Flow Rates

2013 ◽  
Author(s):  
Nicholas Miller ◽  
Sin Chien Siw ◽  
Minking K. Chyu ◽  
Mary Anne Alvin
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Jet Impingement ◽  
Upstream Region ◽  
Channel Height ◽  
Transfer Performance ◽  
Mean Velocity ◽  
Flow Rates ◽  
Downstream Region ◽  
High Heat Transfer

The current detailed experimental study focuses on the optimization of heat transfer performance through jet impingement by varying the coolant flow rate to each individual jet. The test section consists of an array of five jets, which is individually fed and metered separately, and expels air through one exit. The jet diameter D, channel height to jet diameter H/D, and jet spacing to diameter S/D, are all held constant at 9.53 mm (0.375 in), 2 and 4 respectively. The Reynolds number, which is based on jet diameter and bulk mean velocity at each jet, ranges from 50,000 to 80,000. A transient liquid crystal technique is employed in this study to determine the local and overall-average heat transfer coefficient distribution on the target plate. Commercially available CFD software, ANSYS CFX, is used to qualitatively correlate the experimental results and to provide detailed insights of the flow field created by the array of jets. The results revealed higher heat transfer coefficients in the impingement area, while decreasing in the radial direction. The upstream region exhibited high heat transfer performance, which is ultimately driven by the jet impingement from the first jet to the third jet. Heat transfer performance decreases at the downstream region with the development of cross-flow. By varying the jet flow rates at approximately ±2%, local heat transfer at the downstream region is elevated and the total heat transfer enhancement on the target surface is enhanced up to 35% compared to the baseline case.

Experimental Investigation of Area Ratio on Microjet Array Heat Transfer

2009 ◽  
Author(s):  
Gregory J. Michna ◽  
Eric A. Browne ◽  
Yoav Peles ◽  
Michael K. Jensen
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Performance ◽  
Electronics Cooling ◽  
Jet Impingement ◽  
Area Ratio ◽  
Heat Fluxes ◽  
Working Fluid ◽  
Transfer Performance ◽  
Transfer Coefficients ◽  
High Heat Transfer

Electronics cooling is becoming increasingly difficult due to increasing power consumption and decreasing size of processor chips. Heat fluxes in processors and power electronics are quickly approaching levels that cannot be easily addressed by forced air convection over finned heat sinks. Jet impingement cooling offers high heat transfer coefficients and has been used effectively in conventional-scale applications such as turbine blade cooling and the quenching of metals. However, literature in the area of microjet arrays is scarce and has not studied arrays of large area ratios. Hence, the objective of this study is to experimentally assess the heat transfer performance of arrays of microjets. The microjet arrays were fabricated using MEMS processes in a clean room environment. The heat transfer performance of several arrays using deionized water as the working fluid was investigated. Inline and staggered array arrangements were investigated, and the area ratio (total area of the jets divided by the surface area) was varied between 0.036 and 0.35. Reynolds numbers defined by the jet diameter were in the range of 50 to 3,500. Heat fluxes greater than 1,000 W/cm2 were obtained at fluid inlet-to-surface temperature differences of less than 30 °C. Heat transfer performance improved as the area ratio was increased.

Heat Transfer Performance of Internal Cooling Channel With Single-Row Jet Impingement Array by Varying Flow Rates

2016 ◽  
Vol 9 (1) ◽  
Author(s):  
Sin Chien Siw ◽  
Nicholas Miller ◽  
Maryanne Alvin ◽  
Minking Chyu
Keyword(s):  
Heat Transfer ◽  
Flow Rate ◽  
Heat Transfer Performance ◽  
Flow Distribution ◽  
Jet Impingement ◽  
Target Surface ◽  
Internal Cooling ◽  
Transfer Performance ◽  
Flow Rates ◽  
Optimum Flow Rate

The current detailed experimental study focuses on the optimization of heat transfer performance through jet impingement by varying the coolant flow rate to each individual jet. The test section consists of an array of jets, each jet individually fed and metered separately, that expel coolant into the channel and exit through one end. The diameter D, height-to-diameter H/D, and jet spacing-to-diameter S/D are all held constant at 9.53 mm, 2, and 4, respectively. Upon defining the optimum flow rate for each jet, varying diameter jet plates are designed and tested using a similar test setup with the addition of a plenum. Two test cases are conducted by varying the jet diameter within 10% compared to the benchmark jet diameter, 9.53 mm. The Reynolds number, which is based on hydraulic diameter of the channel and total mass flow rate entering the channel, ranges from approximately 52,000 up to 78,000. The transient liquid crystal technique is employed in this study to determine the local and average heat transfer coefficient distributions on the target plate. Commercially available computational fluid dynamics software, ansys cfx, is used to qualitatively correlate the experimental results and to fully understand the flow field distributions within the channel. The results revealed that varying the jet flow rates, total flow varied by approximately ±5% from that of the baseline case, the heat transfer enhancement on the target surface is enhanced up to approximately 35%. However, when transitioning to the varying diameter jet plate, this significant enhancement is suppressed due to the nature of flow distribution from the plenum, combined with the complicated crossflow effects.

Research on Heat Transfer Performance of Water Film for Outside the Tubes of the Microscale Evaporative Condenser

2009 ◽  
Author(s):  
Minghui Hu ◽  
Dongsheng Zhu ◽  
Jialong Shen
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Coefficient ◽  
Transfer Coefficient ◽  
Heat Transfer Performance ◽  
Water Film ◽  
Transfer Performance ◽  
Air Velocity ◽  
Microscale Heat Transfer ◽  
High Heat Transfer ◽  
Spray Density

It is requested to develop a microscale and high performance heat exchanger for small size energy equipments. The heat transfer performance of the water film on the condensing coils of the microscale evaporative condenser was studied for a single-stage compressed refrigeration cycle system. Under various operation conditions, the effects of the spray density and the head-on air velocity on the heat transfer performance of the water film were investigated. The results show that the microscale heat transfer coefficient of the water film αw increases with the increase of spray density and decreases with the increase of head-on air velocity. The results indicate that the key factor affecting the microscale heat transfer of the water film is the spray density. As the results, it is measured that the present device attained high heat transfer quantity despite the weight is light. In addition, via regression analysis of the experimental data, the correlation equation for calculating the microscale heat transfer coefficient of the water film was obtained, its regression correlation coefficient R is 0.98 and the standard deviation is 7.5%. Finally, the correlations from other works were compared. The results presented that the experimental correlation had better consistency with the correlations from other works. In general, the obtained experimental results of the water film heat transfer are helpful to the design and practical operation of the microscale evaporative condensers.

scholarly journals Enhanced heat transfer characteristics of conjugated air jet impingement on a finned heat sink

2017 ◽  
Vol 21 (1 Part A) ◽  
pp. 279-288 ◽  
Author(s):  
Shuxia Qiu ◽  
Peng Xu ◽  
Liping Geng ◽  
Arun Mujumdar ◽  
Zhouting Jiang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Transfer Enhancement ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Cooling System ◽  
Flow Characteristics ◽  
Jet Impingement ◽  
Transfer Performance ◽  
Transfer Enhancement ◽  
Air Jet

Air jet impingement is one of the effective cooling techniques employed in micro-electronic industry. To enhance the heat transfer performance, a cooling system with air jet impingement on a finned heat sink is evaluated via the computational fluid dynamics method. A two-dimensional confined slot air impinging on a finned flat plate is modeled. The numerical model is validated by comparison of the computed Nusselt number distribution on the impingement target with published experimental results. The flow characteristics and heat transfer performance of jet impingement on both of smooth and finned heat sinks are compared. It is observed that jet impingement over finned target plate improves the cooling performance significantly. A dimensionless heat transfer enhancement factor is introduced to quantify the effect of jet flow Reynolds number on the finned surface. The effect of rectangular fin dimensions on impingement heat transfer rate is discussed in order to optimize the cooling system. Also, the computed flow and thermal fields of the air impingement system are examined to explore the physical mechanisms for heat transfer enhancement.

scholarly journals Entropy Generation and Heat Transfer Performance in Microchannel Cooling

Entropy ◽  
2019 ◽  
Vol 21 (2) ◽  
pp. 191 ◽  
Author(s):  
Jundika Kurnia ◽  
Desmond Lim ◽  
Lianjun Chen ◽  
Lishuai Jiang ◽  
Agus Sasmito
Keyword(s):  
Heat Transfer ◽  
Entropy Generation ◽  
Heat Transfer Performance ◽  
Second Law Of Thermodynamics ◽  
High Heat ◽  
Heat Fluxes ◽  
Transfer Performance ◽  
Cooling Channel ◽  
High Heat Transfer ◽  
Microchannel Cooling

Owing to its relatively high heat transfer performance and simple configurations, liquid cooling remains the preferred choice for electronic cooling and other applications. In this cooling approach, channel design plays an important role in dictating the cooling performance of the heat sink. Most cooling channel studies evaluate the performance in view of the first thermodynamics aspect. This study is conducted to investigate flow behaviour and heat transfer performance of an incompressible fluid in a cooling channel with oblique fins with regards to first law and second law of thermodynamics. The effect of oblique fin angle and inlet Reynolds number are investigated. In addition, the performance of the cooling channels for different heat fluxes is evaluated. The results indicate that the oblique fin channel with 20° angle yields the highest figure of merit, especially at higher Re (250–1000). The entropy generation is found to be lowest for an oblique fin channel with 90° angle, which is about twice than that of a conventional parallel channel. Increasing Re decreases the entropy generation, while increasing heat flux increases the entropy generation.

Sign in / Sign up

Export Citation Format

Share Document