Experimental Investigation on Operating Limitation of an Oscillating Heat Pipe

2013 ◽  
Author(s):  
Yulong Ji ◽  
Chao Chang ◽  
Gen Li ◽  
Hongbin Ma ◽  
Yuqing Sun
Keyword(s):  
Experimental Investigation ◽  
Heat Pipe ◽  
Tilt Angle ◽  
Heat Transfer Performance ◽  
Input Power ◽  
Filling Ratio ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe ◽  
Al2o3 Nanofluid

This research represents an experimental investigation on the operating limitation of an oscillating heat pipe (OHP). The OHP has six turns and three sections: evaporator, condenser and adiabatic sections with lengths of 40 mm, 64 mm and 51 mm, respectively. Water or a mixture of water and alumina (Al2O3) making up a nanofluid served as the working fluid. Filling ratios ranging from 30% to 70%, and tilt angles (orientation) ranging from 0° to 90° were studied. The experimental results showed (1) the water/Al2O3 nanofluid can enhance the OHP heat transfer performance, i.e., the highest input power (operating limitation) increased when the OHP was charged with water/Al2O3 nanofluid; (2) the operating limitation increased as the filling ratio increased from 30% to 70%, but the optimum filling ratio of the OHP is 30% or 50% when the working power is lower or higher; and (3) the thermal resistance of the OHP decreased as the tilt angle increased, and the operating limitation increased as the tilt angle increased.

An Experimental Investigation of the Heat Transfer Performance of an Oscillating Heat Pipe With Copper Oxide (CuO) Microstructure Layer on the Inner Surface

2013 ◽  
Vol 135 (7) ◽  
Author(s):  
Yulong Ji ◽  
Chen Xu ◽  
Hongbin Ma ◽  
Pan Xinxiang
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Copper Oxide ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe ◽  
Inner Surface ◽  
Copper Tubing

This paper presents an experimental investigation of whether heat transfer performance in an oscillating heat pipe (OHP) would improve if the inner surface of the heat pipe was coated with a layer of copper oxide (CuO). The OHP had six turns and three sections, i.e., evaporator, condenser, and adiabatic section with lengths of 40 mm, 64 mm, and 51 mm, respectively. The cleaned copper tubing was chemically treated with a chemical solution and heated in a furnace. A microstructure layer of CuO was formed in the inner surface of the OHP with K2S2O8 and KOH. The working fluid in this study was water with filling ratios ranging from 40% to 70%. The experimental results show that the CuO microstructure layer is superhydrophilic and can enhance the OHP heat transfer performance. The investigation results in a new way to enhance the heat transfer performance of an OHP.

Heat Transfer Characteristics of Oscillating Heat Pipe With Water and Ethanol as Working Fluids

2010 ◽  
Vol 132 (12) ◽  
Author(s):  
Haizhen Xian ◽  
Yongping Yang ◽  
Dengying Liu ◽  
Xiaoze Du
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Inclination Angle ◽  
Heat Transfer Performance ◽  
Filling Ratio ◽  
Working Fluid ◽  
Transfer Performance ◽  
Heat Transfer Characteristics ◽  
Oscillating Heat Pipe ◽  
Transfer Characteristics

In this paper, experiments were conducted to achieve a better understanding of the oscillating heat pipe (OHP) operating behavior with water and ethanol as working fluid. The experimental results showed that there existed a necessary temperature difference between the evaporator and the condenser section to keep the heat pipe working. The maximum effective conductivity of the water OHP reached up to 259 kW/m K, while that of the ethanol OHP is of 111 kW/m K. Not all the OHPs are operated in the horizontal operation mode. The heat transfer performance of the ethanol OHP was obviously affected by the filling ratio and the inclination angle but the influence law is irregular. The effect of the filling ratio and the inclination angle of the water OHP were smaller than that of the ethanol one. The heat transfer performance of the OHP was improved with increase of operating temperature. The startup characteristics of the OHP depended on the establishment of the integral oscillating process, which was determined by the operating factors. The startup temperature of the ethanol OHP varied from 40°C to 50°C and that of the water, OHP varied from 40°C to 60°C without considering the horizontal operating mode. The water OHP showed a better performance and more stable heat transfer characteristics than the ethanol OHP, which had no obvious advantages of the startup capability as well.

Experimental Investigation of Ultrasonic Effect on an Acetone Oscillating Heat Pipe

2013 ◽  
Author(s):  
Nannan Zhao ◽  
Benwei Fu ◽  
Dianli Zhao ◽  
Hongbin Ma
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Power Input ◽  
Input Power ◽  
Transfer Performance ◽  
Oscillating Heat Pipe ◽  
Ultrasonic Effect ◽  
Ultrasonic Sound ◽  
Oscillating Motion

The ultrasonic effect on the oscillating motion and heat transfer in an oscillating heat pipe (OHP) containing acetone was investigated experimentally. The ultrasonic sound was applied to the evaporating section of the OHP by using electrically-controlled piezoelectric ceramics. The ultrasonic sound is used to generate and maintain the oscillating motion, and, thereby, heat transfer is enhanced. The heat pipe was tested with or without the ultrasonic sound. In addition, the effects of heat load, filling ratio, orientation, operating temperature, and input power from 15 W to 200 W were investigated. The experimental results demonstrate that ultrasonic sound can affect the oscillating motions and enhance the heat transfer performance of the acetone OHP. In particular, the application of the ultrasonic sound on an acetone OHP can significantly reduce the thermal resistance of the acetone OHP and enhance the heat transfer performance in a low power input region. The investigation will provide an insight into the oscillating mechanism of the acetone OHP influenced by ultrasonic sound and provide a new way to enhance the heat transfer performance of the OHP.

Experimental Study on Oscillating Heat Pipe With Hydraulic Diameter Far Exceeding the Maximum Hydraulic Diameter

2019 ◽  
Author(s):  
Lilin Chu ◽  
Yulong Ji ◽  
Chunrong Yu ◽  
Yantao Li ◽  
Hongbin Ma ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Hydraulic Diameter ◽  
Working Fluid ◽  
Transfer Performance ◽  
Vertical Orientation ◽  
Oscillating Heat Pipe ◽  
Horizontal Orientation ◽  
Small Bubbles

Abstract In order to understand the heat transfer performance, startup and fluid flow condition of oscillating heat pipe (OHP) with hydraulic diameter far exceeding the maximum hydraulic diameter (MHD), an experimental investigation on heat transfer performance and visualization was conducted. From the experimental performance, it is found that the OHP can still work well with ethanol as the working fluid when the tube diameter has exceeded the MHD of 91.6%. In addition, the detailed flow patterns of the OHP were recorded by a highspeed camera for vertical and horizontal orientation to understand its physical mechanism. In the vertical orientation, initially working fluid generates small bubbles, and then the small bubbles coalesce and grow to vapor plugs, the vapor plugs finally pushes the liquid slugs to oscillate in the tube. In the horizontal orientation, the working fluid surface fluctuates due to the vapors flow from the evaporator to the condenser and bubbles burst in the evaporator. When the peak of liquid wave reaches the upper surface of tube, a liquid slug has been formed, and then the steam flow pushes the liquid slugs to oscillate in the tube.

Experimental Investigation of Oscillating Heat Pipe With Hybrid Fluids of Liquid Metal and Water

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Tingting Hao ◽  
Hongbin Ma ◽  
Xuehu Ma
Keyword(s):  
Heat Transfer ◽  
Liquid Metal ◽  
Heat Pipe ◽  
Heat Input ◽  
Heat Transfer Performance ◽  
Pure Water ◽  
Experimental Results ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe

A new oscillating heat pipe (OHP) charged with hybrid fluids can improve thermal performance. The key difference in this OHP is that it uses room temperature liquid metal (Galinstan consisting of gallium, indium, and tin) and water as the working fluid. The OHP was fabricated on a copper plate with six turns and a 3 × 3 mm2 cross section. The OHP with hybrid fluids as the working fluid was investigated through visual observation and thermal measurement. Liquid metal was successfully driven to flow through the OHP by the pressure difference between the evaporator and the condenser without external force. Experimental results show that while added liquid metal can increase the heat transport capability, liquid metal oscillation amplitude decreases as the filling ratio of liquid metal increases. Visualization of experimental results show that liquid metal oscillation position and velocity increase as the heat input increases. Oscillating motion of liquid metal in the OHP significantly increases the heat transfer performance at high heat input. The lowest thermal resistance of 0.076 °C/W was achieved in the hybrid fluids-filled OHP with a heat input of 420 W. We experimentally demonstrated a 13% higher heat transfer performance using liquid metal as the working fluid compared to an OHP charged with pure water.

Effect of Filling Ratio on an Uneven Turn Oscillating Heat Pipe

2011 ◽  
Author(s):  
Aaron A. Hathaway ◽  
Hongbin Ma
Keyword(s):  
Experimental Investigation ◽  
Thermal Resistance ◽  
Flat Plate ◽  
Heat Pipe ◽  
Thermal Performance ◽  
Input Power ◽  
Filling Ratio ◽  
Inverted Position ◽  
Oscillating Heat Pipe ◽  
Test Conditions

An experimental investigation of the effect of filling ratio on the thermal performance for a flat plate oscillating heat pipe with uneven turns was conducted. The OHP was designed to have 14 long turns running from the evaporator to the condenser and 6 short turn occurring only in the evaporator. The factors varied for this experimental investigation were the input power, condensing temperature, and charging ratio. Experimental results show that for all test conditions, the OHP functioned very well and could operate with an input power of up to 1200 W and could reach a thermal resistance of 0.028 °C/W in the inverted position with a filling ratio of 70%.

scholarly journals Experimental Study of the Heat-Transfer Performance of an Extra-Long Gravity-Assisted Heat Pipe Aiming at Geothermal Heat Exploitation

2021 ◽  
Vol 13 (22) ◽  
pp. 12481
Author(s):  
Jiwen Cen ◽  
Feng Li ◽  
Tingliang Li ◽  
Wenbo Huang ◽  
Juanwen Chen ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Water Flow Rate ◽  
Cooling Water ◽  
Filling Ratio ◽  
Working Fluid ◽  
Enhanced Geothermal Systems ◽  
Transfer Performance ◽  
Cooling Water Flow Rate

The installation and operation of enhanced geothermal systems (EGS) involves many challenges. These challenges include the high cost and high risk associated with the investment capital, potential large working-fluid leakage, corrosion of equipment, and subsiding land. A super-long heat pipe can be used for geothermal exploitation to avoid these problems. In this paper, a high aspect-ratio heat pipe (30 m long, 17 mm in inner diameter) is installed vertically. Experiments are then carried out to study its heat-transfer performance and characteristics using several filling ratios of deionized water, different heating powers, and various cooling-water flowrates. The results show that the optimal filling-ratio is about 40% of the volume of the vaporizing section of the heat pipe. Compared with a conventional short heat pipe, the extra-long heat pipe experiences significant thermal vibration. The oscillation frequency depends on the heating power and working-fluid filling ratio. With increasing cooling-water flow rate, the heat-transfer rate of the heat pipe increases before it reaches a plateau. In addition, we investigate the heat-transfer performance of the heat pipe for an extreme working-fluid filling ratio; the results indicate that the lower part of the heat pipe is filled with vapor, which reduces the heat-transfer to the top part. Based on the experimental data, guidelines for designing a heat pipe that can be really used for the exploitation of earth-deep geothermal energy are analyzed.

Copper Oxide (CuO) Effect on Heat Transfer Performance in an Oscillating Heat Pipe

2012 ◽  
Author(s):  
Yulong Ji ◽  
Chen Xu ◽  
Hongbin Ma
Keyword(s):  
Heat Transfer ◽  
Copper Oxide ◽  
Heat Pipe ◽  
Heat Transfer Performance ◽  
Working Fluid ◽  
Transfer Performance ◽  
Oscillating Heat Pipe ◽  
Inner Surface ◽  
Copper Tubing ◽  
Adiabatic Section

An experimental investigation of an oscillating heat pipe (OHP) with an inner surface coated with a copper oxide (CuO) layer was conducted. The OHP has six turns and three sections: evaporator, condenser and adiabatic section with the lengths of 40 mm, 64 mm and 51 mm, respectively. The cleaned copper tubing was chemically treated with a chemical solution and heated in a furnace. A layer of CuO was formed in the inner surface of the OHP. A working fluid (water in this study) at filling ratios ranging from 40% to 70% was studied. The experimental results show that the CuO layer can enhance the heat transfer performance of the OHP. The investigation results in a new way to enhance the heat transfer performance of an OHP.

Sign in / Sign up

Export Citation Format

Share Document