Ventilation of Wind-Permeable Clothed Cylinder Subject to Periodic Swinging Motion

2007 ◽  
Author(s):  
Nesreen Ghaddar ◽  
Kamel Ghali ◽  
Bassel Jreije
Keyword(s):  
Heat Loss ◽  
Cotton Fabric ◽  
Current Model ◽  
Low Frequency ◽  
Ventilation Rate ◽  
External Pressure ◽  
Combined Effect ◽  
Total Heat Loss ◽  
Wind Speeds ◽  
Ventilation Rates

A theoretical and experimental study has been performed to determine ventilation induced by swinging motion and external wind for a fabric-covered cylinder of finite length representing a limb. The estimated ventilation rates are used in determining the sensible heat loss form a clothed cylinder using a simplified resistance model. A model is developed to estimate the external pressure distribution resulting from the relative wind around the swinging clothed cylinder. A mass balance equation of the microclimate air layer is reduced to a pressure equation assuming laminar flow in axial and angular directions and that the air layer is lumped in the radial direction. The ventilation model predicted the total renewal rate during the swinging cycle. A good agreement was found between the predicted ventilation rates at swing frequencies between 40 and 60 rpm and measured values from experiments conducted in a controlled environmental chamber (air velocity is less than 0.05 m/s) and used the tracer gas method to measure the total ventilation rate induced by the swinging motion of a cylinder covered with cotton fabric for both closed and open aperture cases. A parametric study using the current model is performed on cotton fabric to study the effect of wind on ventilation rates for a non-moving clothed limb at wind speeds ranging from 0.5–8 m/s, the effect of a swinging limb in stagnant air at frequencies up to 80 rpm, and the combined effect of wind and swinging motion on the ventilation rate. For a non-moving limb, ventilation rate increases with external wind. In absence of wind, the ventilation rate increases with increased swinging frequency. The combined effect of wind and swing is not additive of the single effects at high wind speed while at low frequency it can be assumed additive for wind speeds below 2 m/s and frequencies below 40 rpm. The heat transfer by ventilation is more than 50% of total heat loss from a clothed cylinder at f = 80 rpm in abs cense and presence of wind.

Ventilation of Wind-Permeable Clothed Cylinder Subject to Periodic Swinging Motion: Modeling and Experimentation

2008 ◽  
Vol 130 (9) ◽  
Author(s):  
N. Ghaddar ◽  
K. Ghali ◽  
B. Jreije
Keyword(s):  
Cotton Fabric ◽  
Current Model ◽  
Ventilation Rate ◽  
External Pressure ◽  
Motion Modeling ◽  
Tracer Gas ◽  
Wind Speeds ◽  
Air Speed ◽  
Local Thermal Comfort ◽  
Ventilation Rates

Abstract A theoretical and experimental study has been performed to determine the ventilation induced by swinging motion and external wind for a fabric-covered cylinder of finite length representing a limb. The estimated ventilation rates are important in determining local thermal comfort. A model is developed to estimate the external pressure distribution resulting from the relative wind around the swinging clothed cylinder. A mass balance equation of the microclimate air layer is reduced to a pressure equation assuming laminar flow in axial and angular directions and that the air layer is lumped in the radial direction. The ventilation model predicts the total renewal rate during the swinging cycle. A good agreement was found between the predicted ventilation rates at swinging frequencies between 40rpm and 60rpm and measured values from experiments conducted in a controlled environmental chamber (air velocity is less than 0.05m∕s) and in a low speed wind tunnel (for air speed between 2m∕s and 6m∕s) using the tracer gas method to measure the total ventilation rate induced by the swinging motion of a cylinder covered with a cotton fabric for both closed and open aperture cases. A parametric study using the current model is performed on a cotton fabric to study the effect of wind on ventilation rates for a nonmoving clothed limb at wind speeds ranging from 0.5m∕sto8m∕s, the effect of a swinging limb in stagnant air at frequencies up to 80rpm, and the combined effect of wind and swinging motion on the ventilation rate. For a nonmoving limb, ventilation rate increases with external wind. In the absence of wind, the ventilation rate increases with increased swinging frequency.

Influence of air temperature on ventilation rates and thermoregulation of a flying bat

1991 ◽  
Vol 260 (5) ◽  
pp. R960-R968 ◽  
Author(s):  
S. P. Thomas ◽  
D. B. Follette ◽  
A. T. Farabaugh
Keyword(s):  
Heat Loss ◽  
Minute Ventilation ◽  
Ventilation Rate ◽  
Evaporative Heat Loss ◽  
Breathing Frequency ◽  
Significant Extent ◽  
Metabolic Heat ◽  
Air Temperatures ◽  
Phyllostomus Hastatus ◽  
Ventilation Rates

To assess the involvement of the ventilatory system in thermoregulation during flight, breathing frequencies and tidal volumes were measured from three Phyllostomus hastatus undertaking steady wind tunnel flights at a constant speed over a range of air temperatures (Ta) from 17.7 to 31.1 degrees C. Mean breathing frequency was independent of Ta, and tidal volume increased only modestly with increasing Ta. Consequently, minute ventilation rate increased insignificantly over the range of Ta values investigated. Mean rectal temperature showed a direct linear relation to Ta and increased significantly from 39.1 to 41.9 degrees C over the range of Ta values investigated. The highest rectal temperatures measured from flying P. hastatus are approximately 3 degrees C less than those of flying birds. In contrast to flying birds, flying P. hastatus does not modulate its rate of respiratory evaporative heat loss to any significant extent in response to environmental heat stress and only loses an estimated 14% of its metabolic heat load by this route. Cutaneous heat loss channels must therefore be very important to these animals. Some reasons for the observed differences in the thermoregulatory responses of flying bats and birds are discussed as well as the relative advantages and limitations of each group's solutions to their thermoregulatory challenges.

scholarly journals Proposing Alternative Solutions to Enhance Natural Ventilation Rates in Residential Buildings in the Cfa Climate Zone of Rasht

2021 ◽  
Vol 13 (2) ◽  
pp. 679
Author(s):  
Roya Aeinehvand ◽  
Amiraslan Darvish ◽  
Abdollah Baghaei Daemei ◽  
Shima Barati ◽  
Asma Jamali ◽  
...  
Keyword(s):  
Natural Ventilation ◽  
Residential Buildings ◽  
Residential Building ◽  
Ventilation Rate ◽  
Humid Climate ◽  
The Sustainable Development ◽  
Passive Strategies ◽  
Development Goals ◽  
Ventilation Rates ◽  
Ventilation Systems

Today, renewable resources and the crucial role of passive strategies in energy efficiency in the building sector toward the sustainable development goals are more indispensable than ever. Natural ventilation has traditionally been considered as one of the most fundamental techniques to decrease energy usage by building dwellers and designers. The main purpose of the present study is to enhance the natural ventilation rates in an existing six-story residential building situated in the humid climate of Rasht during the summertime. On this basis, two types of ventilation systems, the Double-Skin Facade Twin Face System (DSF-TFS) and Single-Sided Wind Tower (SSWT), were simulated through DesignBuilder version 4.5. Then, two types of additional ventilation systems were proposed in order to accelerate the airflow, including four-sided as well as multi-opening wind towers. The wind foldable directions were at about 45 degrees (northwest to southeast). The simulation results show that SSWT could have a better performance than the aforementioned systems by about 38%. Therefore, the multi-opening system was able to enhance the ventilation rate by approximately 10% during the summertime.

Effects of environmental temperature and humidity on evaporative heat loss through firefighter suit materials made with semi-permeable and microporous moisture barriers

2021 ◽  
pp. 004051752110265
Author(s):  
Huipu Gao ◽  
Anthoney Shawn Deaton ◽  
Xiaomeng Fang ◽  
Kyle Watson ◽  
Emiel A DenHartog ◽  
...  
Keyword(s):  
Heat Loss ◽  
Environmental Temperature ◽  
Moisture Absorption ◽  
Evaporative Heat Loss ◽  
Total Heat Loss ◽  
Evaporative Resistance ◽  
Environmental Testing ◽  
Permeable Barrier ◽  
Moisture Condensation ◽  
Moisture Barriers

The goal of this research was to understand how firefighter protective suits perform in different operational environments. This study used a sweating guarded hotplate to examine the effect of environmental temperature (20–45°C) and relative humidity (25–85% RH) on evaporative heat loss through firefighter turnout materials. Four firefighter turnout composites containing three different bi-component (semi-permeable) and one microporous moisture barriers were selected. The results showed that the evaporative resistance of microporous moisture barrier systems was independent of environmental testing conditions. However, absorbed moisture strongly affected evaporative heat loss through semi-permeable moisture barriers coated with a layer of nonporous hydrophilic polymer. Moisture absorption in mild environment (20–25°C) tests, or when testing at high humidity (>85% RH), significantly increased water vapor transmission in semi-permeable turnout systems. It was also found that environmental conditions used in the total heat loss (THL) test (25°C and 65% RH) produced moisture condensation in bi-component barrier systems, making them appear more breathable than could be expected when worn in hotter environments. Regression models successfully qualified the relationships between moisture uptake levels in semi-permeable barrier systems and evaporative resistance and THL. These findings reveal the limitations in relying on THL, the heat strain index currently called for by the NFPA 1971 Standard for Structural Firefighter personal protective equipment, and supports the need to measure turnout evaporative resistance at 35°C (Ret), in addition to THL at 25°C.

scholarly journals Meteorological conditions over Antarctic blue-ice areas and their influence on the local surface mass balance

2001 ◽  
Vol 47 (156) ◽  
pp. 37-50 ◽  
Author(s):  
Richard Bintanja ◽  
Carleen H. Reijmer
Keyword(s):  
Mass Balance ◽  
Low Frequency ◽  
Meteorological Conditions ◽  
Surface Mass Balance ◽  
Surface Mass ◽  
Wind Speeds ◽  
Dry Conditions ◽  
The Difference ◽  
Sublimation Rates ◽  
Different Characteristics

AbstractThis paper addresses the causes of the prevailing meteorological conditions observed over an Antarctic blue-ice area and their effect on the surface mass balance. Over blue-ice areas, net accumulation is zero and ablation occurs mainly through sublimation. Sublimation rates are much higher than over adjacent snowfields. The meteorological conditions favourable for high sublimation rates (warm, dry and gusty) are due to the specific orographic setting of this blue-ice area, with usually a steep upwind mountainous slope causing strong adiabatic heating. Diabatic warming due to radiation, and entrainment of warm air from aloft into the boundary layer augment the warming. The prevailing warm, dry conditions explain roughly 50% of the difference in sublimation, and the different characteristics of blue ice (mainly its lower albedo) the other 50%. Most of the annual sublimation (∼70%) takes place during the short summer (mainly in daytime), with winter ablation being restricted to occasional warm, dry föhn-like events. The additional moisture is effectively removed by entrainment and horizontal advection, which are maximum over the blue-ice area. Low-frequency turbulent motions induced by the upwind mountains enhance the vertical turbulent transports. Strong gusts and high peak wind speeds over blue-ice areas cause high potential snowdrift transports, which can easily remove the total precipitation, thereby maintaining zero accumulation.

Respiratory water and heat loss of the black duck during flight at different ambient temperatures

1971 ◽  
Vol 49 (5) ◽  
pp. 767-774 ◽  
Author(s):  
M. Berger ◽  
J. S. Hart ◽  
O. Z. Roy
Keyword(s):  
Heat Loss ◽  
Water Loss ◽  
Pulmonary Ventilation ◽  
Evaporative Heat Loss ◽  
Total Heat Loss ◽  
Ambient Temperatures ◽  
Black Duck ◽  
Respiratory Heat Loss ◽  
Metabolic Water ◽  
Expired Air

Pulmonary ventilation and temperature of expired air and of the respiratory passages has been measured by telemetry during flight in the black duck (Anas rubripes) and the respiratory water and heat loss has been calculated.During flight, temperature of expired air was higher than at rest and decreased with decreasing ambient temperatures. Accordingly, respiratory water loss as well as evaporative heat loss decreased at low ambient temperatures, whereas heat loss by warming of the inspired air increased. The data indicated respiratory water loss exceeded metabolic water production except at very low ambient temperatures. In the range between −16 °C to +19 °C, the total respiratory heat loss was fairly constant and amounted to 19% of the heat production. Evidence for the independence of total heat loss and production from changes in ambient temperature during flight is discussed.

Hair density, wind speed, and heat loss in mammals

1965 ◽  
Vol 20 (4) ◽  
pp. 796-801 ◽  
Author(s):  
R. T. Tregear
Keyword(s):  
Wind Speed ◽  
Temperature Gradient ◽  
Heat Loss ◽  
Thermal Insulation ◽  
Hair Density ◽  
Wind Speeds

The heat loss from excised pelts of rabbits, horses, and pigs has been measured at various wind speeds. The temperature gradient through the fur was also measured. The thermal insulation of fur is highly dependent on the hair density (i.e., number of hairs/ cm2), and on the wind passing over its surface. If there are less than 1,000 hairs/cm2, an 8-mph wind penetrates deep into the fur, but at higher hair densities an 18-mph wind penetrates only a little way into the fur. fur insulation; obstruction of wind by hair Submitted on September 10, 1964

scholarly journals Local Characteristics of the Nocturnal Boundary Layer in Response to External Pressure Forcing

2017 ◽  
Vol 56 (11) ◽  
pp. 3035-3047 ◽  
Author(s):  
Steven J. A. van der Linden ◽  
Peter Baas ◽  
J. Antoon van Hooft ◽  
Ivo G. S. van Hooijdonk ◽  
Fred C. Bosveld ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Wind Speed ◽  
Stable Boundary Layer ◽  
Dynamical Behavior ◽  
Geostrophic Wind ◽  
External Pressure ◽  
Near Surface ◽  
Stable Boundary ◽  
Wind Speeds ◽  
Turbulent Characteristics

AbstractGeostrophic wind speed data, derived from pressure observations, are used in combination with tower measurements to investigate the nocturnal stable boundary layer at Cabauw, the Netherlands. Since the geostrophic wind speed is not directly influenced by local nocturnal stability, it may be regarded as an external forcing parameter of the nocturnal stable boundary layer. This is in contrast to local parameters such as in situ wind speed, the Monin–Obukhov stability parameter (z/L), or the local Richardson number. To characterize the stable boundary layer, ensemble averages of clear-sky nights with similar geostrophic wind speeds are formed. In this manner, the mean dynamical behavior of near-surface turbulent characteristics and composite profiles of wind and temperature are systematically investigated. The classification is found to result in a gradual ordering of the diagnosed variables in terms of the geostrophic wind speed. In an ensemble sense the transition from the weakly stable to very stable boundary layer is more gradual than expected. Interestingly, for very weak geostrophic winds, turbulent activity is found to be negligibly small while the resulting boundary cooling stays finite. Realistic numerical simulations for those cases should therefore have a comprehensive description of other thermodynamic processes such as soil heat conduction and radiative transfer.

scholarly journals Combined impacts of elevated CO2 and anthropogenic noise on European sea bass (Dicentrarchus labrax)

2016 ◽  
Vol 74 (4) ◽  
pp. 1230-1236 ◽  
Author(s):  
Danielle A. Poulton ◽  
Cosima S. Porteus ◽  
Stephen D. Simpson
Keyword(s):  
Elevated Co2 ◽  
Low Frequency ◽  
Dicentrarchus Labrax ◽  
Sea Bass ◽  
Ventilation Rate ◽  
Anthropogenic Noise ◽  
Pile Driving ◽  
European Sea Bass ◽  
Ventilatory Responses ◽  
Carbon Dioxide Co2

Ocean acidification (OA) and anthropogenic noise are both known to cause stress and induce physiological and behavioural changes in fish, with consequences for fitness. OA is also predicted to reduce the ocean's capacity to absorb low-frequency sounds produced by human activity. Consequently, anthropogenic noise could propagate further under an increasingly acidic ocean. For the first time, this study investigated the independent and combined impacts of elevated carbon dioxide (CO2) and anthropogenic noise on the behaviour of a marine fish, the European sea bass (Dicentrarchus labrax). In a fully factorial experiment crossing two CO2 levels (current day and elevated) with two noise conditions (ambient and pile driving), D. labrax were exposed to four CO2/noise treatment combinations: 400 µatm/ambient, 1000 µatm/ambient, 400 µatm/pile-driving, and 1000 µatm/pile-driving. Pile-driving noise increased ventilation rate (indicating stress) compared with ambient noise conditions. Elevated CO2 did not alter the ventilation rate response to noise. Furthermore, there was no interaction effect between elevated CO2 and pile-driving noise, suggesting that OA is unlikely to influence startle or ventilatory responses of fish to anthropogenic noise. However, effective management of anthropogenic noise could reduce fish stress, which may improve resilience to future stressors.

Cavity receiver thermal performance analysis based on total heat loss coefficient and efficiency factor

2018 ◽  
Vol 42 (6) ◽  
pp. 2284-2289 ◽  
Author(s):  
Qiangqiang Zhang ◽  
Xin Li ◽  
Zhifeng Wang ◽  
Zhi Li ◽  
Hong Liu ◽  
...  
Keyword(s):  
Performance Analysis ◽  
Heat Loss ◽  
Thermal Performance ◽  
Efficiency Factor ◽  
Loss Coefficient ◽  
Total Heat ◽  
Total Heat Loss
Sign in / Sign up

Export Citation Format

Share Document