Numerical Investigation of Laminar Impinging Jet Heat Transfer to Finned Heat Sinks

2005 ◽  
Author(s):  
Z. Q. Lou ◽  
C. Yap ◽  
A. S. Mujumdar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Dynamic Performance ◽  
Impinging Jet ◽  
Heat Sinks ◽  
Dielectric Fluid ◽  
Fluid Medium ◽  
Spacing Ratio

A numerical study has been carried out to examine the conjugate heat transfer under a confined impinging jet using a plate-fin heat sink as the target plate. Effects of geometric parameters such as fin number, fin height and fin-to-spacing ratio are examined over a range of jet Reynolds numbers using dielectric fluid FC-72 as the fluid medium. Thermal resistance, pressure drop and Nusselt number are the main criteria used to evaluate the thermal and fluid dynamic performance of this flow system. Furthermore, the effects of fin height, fin-to-spacing ratio and jet Reynolds number on impinging jet heat transfer are obtained. The concept of an effective Nusselt number is introduced for computing the heat transfer effectiveness of heat sinks with different fin numbers.

A Numerical Study of a Heat Sink Fin Under a Laminar Impinging Jet

2008 ◽  
Vol 130 (3) ◽  
Author(s):  
Z. Q. Lou ◽  
C. Yap ◽  
A. S. Mujumdar
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Heat Sink ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Dynamic Performance ◽  
Impinging Jet ◽  
Dielectric Fluid ◽  
Fluid Medium ◽  
Spacing Ratio

Impinging jet heat transfer is a promising method to cool electronic components. In this paper, a numerical study has been carried out to examine the conjugate heat transfer under a confined impinging jet using a plate-fin heat sink as the target plate. Effects of geometric parameters such as fin number, fin height, and fin-to-spacing ratio are examined over a range of jet Reynolds numbers using dielectric fluid FC-72 as the fluid medium. Thermal resistance, pressure drop, and Nusselt number are the main criteria used to evaluate the thermal and fluid dynamic performance of this flow system. Furthermore, the effects of fin height, fin-to-spacing ratio, and jet Reynolds number on impinging jet heat transfer are obtained. The concept of an effective Nusselt number is introduced for computing the heat transfer effectiveness of heat sinks with different fin numbers.

Study of a Cooling Feed Pipe With a Covering Plate on a Ribbed Turbine Case

2019 ◽  
Vol 141 (7) ◽  
Author(s):  
Fangyuan Liu ◽  
Junkui Mao ◽  
Chao Han ◽  
Yuanjian Liu ◽  
Xingsi Han ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Nusselt Number ◽  
Experimental Tests ◽  
Impinging Jet ◽  
Nusselt Numbers ◽  
Spacing Ratio ◽  
Wall Flow ◽  
Complicated Geometry ◽  
Clearance Control

Considering the complicated geometry in an active clearance control (ACC) system, the design of an improved cooling feed pipe with a covering plate for a high pressure ribbed turbine case was investigated. Numerical calculations were analyzed to obtain the interactions between the impinging jet arrays fed by the pipe. Experimental tests were performed to explore the effect of the Reynolds number (2000–20,000) and the jet-to-surface spacing ratio (6–10) on the streamwise-averaged Nusselt numbers. Additionally, the effect of the crossflow produced by the configuration was investigated. Results showed a confined curved channel was formed by the pipe and ribbed case, which resulted in crossflow. The crossflow evolved into vortices and the streamwise-averaged Nusselt number on the high ribs was subsequently increased. Furthermore, the distribution of the heat transfer on the entire surface became more uniform compared with that of traditional impinging jet arrays. A higher Nusselt number was achieved by decreasing the jet-to-surface spacing and increasing the Reynolds number. This investigation has revealed a cooling configuration for controlling the wall flow and evening the heat transfer on the case surface, especially for the ribs.

Impinging Jet Cooled Plate Fin Heat Sinks With Turbulators Enhancement

2009 ◽  
Author(s):  
Ganesh Subbuswamy ◽  
Xianchang Li
Keyword(s):  
Heat Transfer ◽  
Reynolds Number ◽  
Heat Sink ◽  
Numerical Study ◽  
Turbine Blades ◽  
Jet Impingement ◽  
Impinging Jet ◽  
Impinging Jets ◽  
Heat Sinks ◽  
Internal Cooling

Extended surfaces (fins) and impinging jets have been used to enhance heat transfer in many applications. In electronic thermal management, heat sinks can be designed to take advantage of the combined effect of fins and jet impingement such as jets impinging on an array of pin fins or plate fins. Significant studies have been focused on the thermal resistance, pressure drop, and the parametric effect of Reynolds number, fin thickness, density, and height. To further improve the heat sink performance, ribs/turbulators, which are widely employed in internal cooling of gas turbine blades, can be integrated into the plate fins, especially close to the surface area with low heat transfer coefficient. Numerical study is performed in this paper to examine the flow and heat transfer behavior of plate fin heat sinks cooled by an impinging jet and enhanced by the ribs. The height and shape of the turbulators are investigated to achieve the best performance. Parametric studies also include the flow Reynolds number and the spacing between the ribs. Heat transfer mechanism is explored for the confined turbulence jet with and without turbulators. It is expected that the rib enhancement can lead to a more cost-effective heat sink for cooling of electronic components. Further enhancement and optimization are discussed in this paper.

Heat transfer characteristics of nanofluids from a sinusoidal corrugated cylinder placed in a square cavity

2021 ◽  
pp. 095440622110272
Author(s):  
Salaika Parvin ◽  
Nepal Chandra Roy ◽  
Litan Kumar Saha ◽  
Sadia Siddiqa
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Rayleigh Number ◽  
Aspect Ratio ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Heat Transfer Characteristics ◽  
Number Range ◽  
Transfer Characteristics ◽  
Wide Range

A numerical study is performed to investigate nanofluids' flow field and heat transfer characteristics between the domain bounded by a square and a wavy cylinder. The left and right walls of the cavity are at constant low temperature while its other adjacent walls are insulated. The convective phenomena take place due to the higher temperature of the inner corrugated surface. Super elliptic functions are used to transform the governing equations of the classical rectangular enclosure into a system of equations valid for concentric cylinders. The resulting equations are solved iteratively with the implicit finite difference method. Parametric results are presented in terms of streamlines, isotherms, local and average Nusselt numbers for a wide range of scaled parameters such as nanoparticles concentration, Rayleigh number, and aspect ratio. Several correlations have been deduced at the inner and outer surface of the cylinders for the average Nusselt number, which gives a good agreement when compared against the numerical results. The strength of the streamlines increases significantly due to an increase in the aspect ratio of the inner cylinder and the Rayleigh number. As the concentration of nanoparticles increases, the average Nusselt number at the internal and external cylinders becomes stronger. In addition, the average Nusselt number for the entire Rayleigh number range gets enhanced when plotted against the volume fraction of the nanofluid.

Oscillatory Heat Transfer in a Pipe Subjected to a Laminar Reciprocating Flow

1996 ◽  
Vol 118 (3) ◽  
pp. 592-597 ◽  
Author(s):  
T. S. Zhao ◽  
P. Cheng
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Heat Flux ◽  
Nusselt Number ◽  
Numerical Study ◽  
Temperature Cycle ◽  
Uniform Heat Flux ◽  
Fluid Temperature ◽  
Cycle Space ◽  
Reciprocating Flow

An experimental and numerical study has been carried out for laminar forced convection in a long pipe heated by uniform heat flux and subjected to a reciprocating flow of air. Transient fluid temperature variations in the two mixing chambers connected to both ends of the heated section were measured. These measurements were used as the thermal boundary conditions for the numerical simulation of the hydrodynamically and thermally developing reciprocating flow in the heated pipe. The coupled governing equations for time-dependent convective heat transfer in the fluid flow and conduction in the wall of the heated tube were solved numerically. The numerical results for time-resolved centerline fuid temperature, cycle-averaged wall temperature, and the space-cycle averaged Nusselt number are shown to be in good agreement with the experimental data. Based on the experimental data, a correlation equation is obtained for the cycle-space averaged Nusselt number in terms of appropriate dimensionless parameters for a laminar reciprocating flow of air in a long pipe with constant heat flux.

Pin-Fin Heat Sink With Horizontal Base and Blocked Edges

2008 ◽  
Author(s):  
D. Sahray ◽  
H. Shmueli ◽  
N. Segal ◽  
G. Ziskind ◽  
R. Letan
Keyword(s):  
Heat Transfer ◽  
Free Convection ◽  
Contact Resistance ◽  
Cross Section ◽  
Heat Input ◽  
Heat Sink ◽  
Numerical Study ◽  
Heat Sinks ◽  
Transfer Enhancement ◽  
Pin Fin

In the present work, horizontal-base pin fin heat sinks exposed to free convection in air are studied. They are made of aluminum, and there is no contact resistance between the base and the fins. For the same base dimensions the fin height and pitch vary. The fins have a constant square cross-section. The edges of the sink are blocked: the surrounding insulation is flush with the fin tips. The effect of fin height and pitch on the performance of the sink is studied experimentally and numerically. In the experiments, the heat sinks are heated using foil electrical heaters. The heat input is set, and temperatures of the base and fins are measured. In the corresponding numerical study, the sinks and their environment are modeled using the Fluent 6 software. The results show that heat transfer enhancement due to the fins is not monotonic. The differences between sparsely and densely populated sinks are analyzed for various fin heights. Also assessed are effects of the blocked edges as compared to the previously studied cases where the sink edges were exposed to the surroundings.

Effect of Periodicity of Non-Uniform Sinusoidal Side Heating on Natural Convection in an Anisotropic Porous-Enclosure

2011 ◽  
Vol 110-116 ◽  
pp. 1613-1618 ◽  
Author(s):  
S. Kapoor ◽  
P. Bera
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Natural Convection ◽  
Stream Function ◽  
Numerical Study ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Maximum Heat ◽  
Maximum Heat Transfer ◽  
Porous Enclosure

A comprehensive numerical study on the natural convection in a hydrodynamically anisotropic as well as isotropic porous enclosure is presented, flow is induced by non uniform sinusoidal heating of the right wall of the enclosure. The principal directions of the permeability tensor has been taken oblique to the gravity vector. The spectral Element method has been adopted to solve numerically the governing differential equations by using the vorticity-stream-function approach. The results are presented in terms of stream function, temperature profile and Nusselt number. The result show that the maximum heat transfer takes place at y = 1.5 when N is odd.. Also, increasing media permeability, by changing K* = 1 to K* = 0.2, increases heat transfer rate at below and above right corner of the enclosure. Furthermore, for the all values of N, profiles of local Nusselt number (Nuy) in isotropic as well as anisotropic media are similar, but for even values of N differ slightly at N = 2.. In particular the present analysis shows that, different periodicity (N) of temperature boundary condition has the significant effect on the flow pattern and consequently on the local heat transfer phenomena.

scholarly journals Natural convection in a differentially heated enclosure with triangular roof

1970 ◽  
Vol 39 (1) ◽  
pp. 1-7 ◽  
Author(s):  
Sumon Saha ◽  
Noman Hasan ◽  
Chowdhury Md Feroz
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Fluid Flow ◽  
Natural Convection ◽  
Average Nusselt Number ◽  
Numerical Study ◽  
Convection Heat Transfer ◽  
Element Analysis ◽  
Left Wall ◽  
Square Enclosure

A numerical study has been carried out for laminar natural convection heat transfer within a two-dimensional modified square enclosure having a triangular roof. The vertical sidewalls are differentially heated considering a constant flux heat source strip is flush mounted with the left wall. The opposite wall is considered isothermal having a temperature of the surrounding fluid. The rest of the walls are adiabatic. Air is considered as the fluid inside the enclosure. The solution has been carried out on the basis of finite element analysis by a non-linear parametric solver to examine the heat transfer and fluid flow characteristics. Different heights of the triangular roof have been considered for the present analysis. Fluid flow fields and isotherm patterns and the average Nusselt number are presented for the Rayleigh numbers ranging from 103 to 106 in order to show the effects of these governing parameters. The average Nusselt number computed for the case of isoflux heating is also compared with the case of isothermal heating as available in the literature. The outcome of the present investigation shows that the convective phenomenon is greatly influenced by the inclined roof height. Keywords: Natural convection, triangular roof, Rayleigh number, isoflux heating. Doi:10.3329/jme.v39i1.1826 Journal of Mechanical Engineering, vol. ME39, No. 1, June 2008 1-7

Sign in / Sign up

Export Citation Format

Share Document