Experimental Investigation With Optical Diagnostics of a Lean-Premixed Aero-Engine Injection System Under Relevant Operating Conditions

2017 ◽  
Author(s):  
P. Malbois ◽  
E. Salaun ◽  
F. Frindt ◽  
G. Cabot ◽  
B. Renou ◽  
...  
Keyword(s):  
Flame Length ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Injection System ◽  
Exhaust Gas ◽  
Laser Propagation ◽  
Aero Engine ◽  
Lean Premixed ◽  
Gradient Based

A Lean-Premixed (LP) aero-engine injection system was experimentally studied using optically-based measurements. Experiments were conducted under relevant operating conditions up to 1.38 MPa and using commercial kerosene as fuel. First of all, the structure of the reaction zone and the flame length into the combustion chamber have been studied with CH* chemiluminescence. It is observed from the data measurements that combustion can produce two types of flames, a V-shaped flame in which combustion is stabilized a few mm downstream from the injector and a tulip flame in which combustion is developing inside the injection system. The flame is found to be shorter and more confined when increasing the pressure. To complement this study, experiments were also performed using the OH-PLIF measurement technique. Data processing of the absorption of OH fluorescence signals along the laser propagation allowed the determination of the absolute distribution of OH concentration without any calibration of the OH fluorescence signals. The obtained values are in agreement with estimated premixed adiabatic chemical equilibrium results. Furthermore, the flame front location and its structure were captured from gradient-based filtering operations on OH-PLIF signals. Finally, pollutant emissions were also measured with an exhaust gas sampling probe positioned downstream from the combustor outlet. It has been found that NOx emission increases with Fuel Air Ratio (FAR) and pressure whereas CO exhibits an inverse trend.

scholarly journals Measurement of Air-Fuel Ratio Fluctuations Caused by Combustor Driven Oscillations

1998 ◽  
Author(s):  
Rajiv Mongia ◽  
Robert Dibble ◽  
Jeff Lovett
Keyword(s):  
Power Spectrum ◽  
Mole Fraction ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Premixed Combustion ◽  
Pollutant Emissions ◽  
Combustion Instabilities ◽  
Pressure Oscillations ◽  
Lean Premixed Combustion ◽  
Lean Premixed

Lean premixed combustion has emerged as a method of achieving low pollutant emissions from gas turbines. A common problem of lean premixed combustion is combustion instability. As conditions inside lean premixed combustors approach the lean flammability limit, large pressure variations are encountered. As a consequence, certain desirable gas turbine operating regimes are not approachable. In minimizing these regimes, combustor designers must rely upon trial and error because combustion instabilities are not well understood (and thus difficult to model). When they occur, pressure oscillations in the combustor can induce fluctuations in fuel mole fraction that can augment the pressure oscillations (undesirable) or dampen the pressure oscillations (desirable). In this paper, we demonstrate a method for measuring the fuel mole fraction oscillations which occur in the premixing section during combustion instabilities produced in the combustor that is downstream of the premixer. The fuel mole fraction in the premixer is measured with kHz resolution by the absorption of light from a 3.39 μm He-Ne laser. A sudden expansion combustor is constructed to demonstrate this fuel mole fraction measurement technique. Under several operating conditions, we measure significant fuel mole fraction fluctuations that are caused by pressure oscillations in the combustion chamber. Since the fuel mole fraction is sampled continuously, a power spectrum is easily generated. The fuel mole fraction power spectrum clearly indicates fuel mole fraction fluctuation frequencies are the same as the pressure fluctuation frequencies under some operating conditions.

Influence of Low Ambient Temperatures on the Exhaust Gas and Deposit Composition of Gasoline Engines

2021 ◽  
pp. 1-11
Author(s):  
Dominik Appel ◽  
Fabian P. Hagen ◽  
Uwe Wagner ◽  
Thomas Koch ◽  
Henning Bockhorn ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Gasoline Engine ◽  
Cold Start ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Ex Situ ◽  
Exhaust Gas ◽  
Gasoline Engines ◽  
Ambient Temperatures ◽  
Aftertreatment Systems

Abstract To comply with future emission regulations for internal combustion engines, system-related cold-start conditions in short-distance traffic constitute a particular challenge. Under these conditions, pollutant emissions are seriously increased due to internal engine effects and unfavorable operating conditions of the exhaust aftertreatment systems. As a secondary effect, the composition of the exhaust gases has a considerable influence on the deposition of aerosols via different deposition mechanisms and on fouling processes of exhaust gas-carrying components. Also, the performance of exhaust gas aftertreatment systems may be affected disadvantageously. In this study, the exhaust gas and deposit composition of a turbocharged three-cylinder gasoline engine is examined in-situ upstream of the catalytic converter at ambient and engine starting temperatures of -22 °C to 23 °C using a Fourier-transform infrared spectrometer and a particle spectrometer. For the cold start investigation, a modern gasoline engine with series engine periphery is used. In particular, the investigation of the behavior of deposits in the exhaust system of gasoline engines during cold start under dynamic driving conditions represents an extraordinary challenge due to an average lower soot concentration in the exhaust gas compared to diesel engines and so far, has not been examined in this form. A novel sampling method allows ex-situ analysis of formed deposits during a single driving cycle. Both, particle number concentration and the deposition rate are higher in the testing procedure of Real Driving Emissions (RDE) than in the inner-city part of the Worldwide harmonized Light vehicles Test Cycle (WLTC). In addition, reduced ambient temperatures increase the amount of deposits, which consist predominantly of soot and to a minor fraction of volatile compounds. Although the primary particle size distributions of the deposited soot particles do not change when boundary conditions change, the degree of graphitization within the particles increases with increasing exhaust gas temperature.

Impact of Fuel Composition on Blow Off and Flashback in Swirl Stabilized Lean Premixed Combustion

2013 ◽  
Author(s):  
Amin Akbari ◽  
Vincent McDonell ◽  
Scott Samuelsen
Keyword(s):  
Natural Gas ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Combustion Stability ◽  
Pollutant Emissions ◽  
Fuel Composition ◽  
Pure Hydrogen ◽  
Combustion Properties ◽  
Lean Premixed ◽  
The Impact

Co firing of natural gas with renewable fuels such as hydrogen can reduce greenhouse gas emissions, and meet other sustainability considerations. At the same time, adding hydrogen to natural gas alters combustion properties, such as burning speeds, heating values, flammability limits, and chemical characteristics. It is important to identify how combustion stability relates to fuel mixture composition in industrial gas turbines and burners and correlate such behavior to fuel properties or operating conditions. Ultimately, it is desired to predict and prevent operability issues when designing a fuel flexible gas turbine combustor. Fuel interchangeability is used to describe the ability of a substitute fuel composition to replace a baseline fuel without significantly altering performance and operation. Any substitute fuel, while maintaining the same heating load as the baseline fuel, must also provide stable combustion with low pollutant emissions. Interchangeability indices try to predict the impact of fuel composition on lean blowoff and flashback. Correlations for operability limits have been reported, though results are more consistent for blowoff compared to flashback. Yet, even for blowoff, some disagreement regarding fuel composition effects are evident. In the present work, promising correlations and parameters for lean blow off and flashback in a swirl stabilized lean premixed combustor are evaluated. Measurements are conducted for fuel compositions ranging from pure natural gas to pure hydrogen under different levels of preheat and air flow rates. The results are used to evaluate the ability of existing approaches to predict blowoff and flashback. The results show that, while a Damköhler number approach for blowoff is promising, important considerations are required in applying the method. For flashback, the quench constant parameter suggested for combustion induced vortex breakdown was applied and found to have limited success for predicting flashback in the present configuration.

Fluid Dynamics and Detailed Kinetic Modeling of Pollutant Emissions From Lean Combustion Systems

2010 ◽  
Author(s):  
Alessio Frassoldati ◽  
Alberto Cuoci ◽  
Tiziano Faravelli ◽  
Eliseo Ranzi ◽  
Salvatore Colantuoni ◽  
...  
Keyword(s):  
Fluid Dynamics ◽  
Reacting Flows ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Injection System ◽  
Turbulent Reacting Flows ◽  
Gas Temperature ◽  
Lean Combustion ◽  
Core Concepts ◽  
Detailed Kinetics

A methodology for computing steady turbulent reacting flows and the formation of pollutants in combustors for aeroengine applications is presented. The aim of this paper is to describe and to further validate the proposed computational approach. A 3-D computational fluid dynamics (CFD) proprietary code and a Kinetic Post-Processor (KPP) have been coupled and applied to calculate the gas temperature and pollutant emissions. The thermo-fluid dynamics results of the CFD code are post-processed by the KPP with the use of detailed kinetics for predicting pollutant emissions, with special emphasis on nitrogen oxides. A new application of the above calculation methodology has been carried out on an injection system based on Partial Evaporation and Rapid Mixing (PERM) concept, designed and developed in the frame of the EU program for NEW Aero engine Core concepts (NEWAC). This injection system was studied experimentally at Karlsruhe University and ONERA using a tubular combustor, in order to perform the first assessment in terms pollutant emissions at the outlet at different operating conditions. The model predictions are compared with experimental results and globally the agreement is satisfactory, especially for NOx emissions. The analysis of the data presented in this paper provides useful information for further improvements in both modeling and experimental activities.

Effects of Exhaust Gas Recirculation on Particulate Morphology from a Diesel Engine

2013 ◽  
Vol 664 ◽  
pp. 926-930
Author(s):  
Wei Zhang ◽  
Xiao Dong Wang ◽  
Rui Sun ◽  
Jian Wei Sun ◽  
Wei Han
Keyword(s):  
Particle Size ◽  
Diesel Engine ◽  
Primary Particle ◽  
Morphological Characteristics ◽  
Exhaust Gas Recirculation ◽  
Operating Conditions ◽  
Injection System ◽  
Exhaust Gas ◽  
Aggregate Particle ◽  
Gas Recirculation

The effects of EGR operating mode on particulate morphology were investigated for a 5.79-liter diesel engine which was equipped with a turbocharged and inter-cooled air induction system, a common-rail direct fuel injection system, and an EGR system. Morphological characteristics, such as primary particle size, number concentration and aggregate particle size were investigated by a transmission electron microscope (TEM) analysis and a electrical low pressure impactor (ELPI) under engine operating conditions of 0.41 in fuel/air ratio at different exhaust gas recirculation (EGR) rate from 0～35%. The experimental results indicated that primary particle were in the range of 17.05nm～18.34nm, which increased with increased EGR rate. As EGR rate increased, aggregate particle size were measured in a narrow range from 120nm to 170nm.

Influence of Low Ambient Temperatures on the Exhaust Gas and Deposit Composition of Gasoline Engines

2020 ◽  
Author(s):  
Dominik Appel ◽  
Fabian P. Hagen ◽  
Uwe Wagner ◽  
Thomas Koch ◽  
Henning Bockhorn ◽  
...  
Keyword(s):  
Internal Combustion Engines ◽  
Gasoline Engine ◽  
Cold Start ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Ex Situ ◽  
Exhaust Gas ◽  
Gasoline Engines ◽  
Ambient Temperatures ◽  
Aftertreatment Systems

Abstract To comply with future emission regulations for internal combustion engines, system-related cold-start conditions in short-distance traffic constitute a particular challenge. Under these conditions, pollutant emissions are seriously increased due to internal engine effects and unfavorable operating conditions of the exhaust aftertreatment systems. As a secondary effect, the composition of the exhaust gases has a considerable influence on the deposition of aerosols via different deposition mechanisms and on fouling processes of exhaust gas-carrying components. Also, the performance of exhaust gas aftertreatment systems may be affected disadvantageously. In this study, the exhaust gas and deposit composition of a turbocharged three-cylinder gasoline engine is examined in-situ upstream of the catalytic converter at ambient and engine starting temperatures of −22 °C to 23 °C using a Fourier-transform infrared spectrometer and a particle spectrometer. For the cold start investigation, a modern gasoline engine with series engine periphery is used. In particular, the investigation of the behavior of deposits in the exhaust system of gasoline engines during cold start under dynamic driving conditions represents an extraordinary challenge due to an average lower soot concentration in the exhaust gas compared to diesel engines and so far, has not been examined in this form. A novel sampling method allows ex-situ analysis of formed deposits during a single driving cycle. Both, particle number concentration and the deposition rate are higher in the testing procedure of Real Driving Emissions (RDE) than in the inner-city part of the Worldwide harmonized Light vehicles Test Cycle (WLTC). In addition, reduced ambient temperatures increase the amount of deposits, which consist predominantly of soot and to a minor fraction of volatile compounds. Although the primary particle size distributions of the deposited soot particles do not change when boundary conditions change, the degree of graphitization within the particles increases with increasing exhaust gas temperature.

Experimental Determination of Liquefied Petroleum Gas–Gasoline Mixtures Knock Resistance

2014 ◽  
Vol 136 (12) ◽  
Author(s):  
Emiliano Pipitone ◽  
Giuseppe Genchi
Keyword(s):  
Fuel Injection ◽  
Molar Fraction ◽  
Pollutant Emissions ◽  
Injection System ◽  
Liquefied Petroleum Gas ◽  
High Compression Ratio ◽  
Experimental Researches ◽  
Mass Basis ◽  
Engine Size

The results of previous experimental researches showed that great advantages can be achieved, both in terms of fuel consumption and pollutant emissions, in bifuel vehicles by means of the double-fuel combustion, i.e., the simultaneous combustion of gasoline and a gaseous fuel, such as liquefied petroleum gas (LPG) or natural gas (NG). The substantial increase in knock resistance pursued by adding LPG to gasoline, which allowed to maintain an overall stoichiometric proportion with air also at full load, is not documented in the scientific literature and induced the authors to perform a proper experimental campaign. The motor octane number (MON) of LPG–gasoline mixtures has been hence determined on a standard cooperative fuel research (CFR) engine, equipped with a double-fuel injection system in order to realize different proportions between the two fuels and electronically control the overall air–fuels mixture. The results of the measurement show a quadratic dependence of the MON of the mixture as function of the LPG concentration evaluated on a mass basis, with higher increase for the lower LPG content. A good linear relation, instead, has been determined on the basis of the evaluated LPG molar fraction. The simultaneous combustion of LPG and gasoline may become a third operative mode of bifuel vehicles, allowing to optimize fuel economy, performances, and pollutant emissions; turbocharged bifuel engines could strongly take advantage of the knock resistance of the fuels mixture thus adopting high compression ratio (CR) both in pure gas and double-fuel mode, hence maximizing performance and reducing engine size. The two correlations determined in this work, hence, can be useful for the design of future bifuel engines running with knock safe simultaneous combustion of LPG and gasoline.

scholarly journals Palm H-FAME Production through Partially Hydrogenation using Nickel/Carbon Catalyst to Increase Oxidation Stability

2018 ◽  
Vol 156 ◽  
pp. 03004
Author(s):  
Elsa Ramayeni ◽  
Bambang Heru Susanto ◽  
Dimas Firlyansyah Pratama
Keyword(s):  
Oxidation Stability ◽  
Acid Methyl Ester ◽  
Operating Conditions ◽  
Injection System ◽  
Empirical Measure ◽  
Partial Hydrogenation ◽  
Carbon Catalyst ◽  
Pump System ◽  
Speed Up

One of the methods to improve the oxidation stability of palm biodiesel is through partially hydrogenation. The production using Nickel/Carbon catalyst to speed up the reaction rate. Product is called Palm H-FAME (Hydrogenated FAME). Partial hydrogenation breaks the unsaturated bond on FAME (Fatty Acid Methyl Ester), which is a key component of the determination of oxidative properties. Changes in FAME composition by partial hydrogenation are predicted to change the oxidation stability so it does not cause deposits that can damage the injection system of diesel engine, pump system, and storage tank. Partial hydrogenation is carried out under operating conditions of 120 °C and 6 bar with 100:1, 100:3, 100:5, 100:10 % wt catalyst in the stirred batch autoclave reactor. H-FAME synthesis with 100:5 % wt Ni/C catalyst can decrease the iodine number which is the empirical measure of the number of unsaturated bonds from 91.78 to 82.38 (g-I2/100 g) with an increase of oxidation stability from 585 to 602 minutes.

scholarly journals Environmental safety management of urban building by regulation of formation process of exhaust gases of motor vehicles

2018 ◽  
Vol 196 ◽  
pp. 04065
Author(s):  
Liparit Badalyan ◽  
Vladimir Kurdjukov ◽  
Alla Ovcharenko
Keyword(s):  
Flow Rate ◽  
Combustion Engine ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Motor Vehicles ◽  
Economic Losses ◽  
Reliable Determination ◽  
Exhaust Gases ◽  
Modern Development

Modern development of the construction industry involves accounting and assessment of operating conditions of structures. Excessive technological environmental impact can lead to economic losses and a decrease in the efficiency of investment projects in construction. Mobile sources emission record is an important component of the ecosystem state diagnosis in modern cities. For scientifically substantiated and reliable determination of the mass flow of the motor vehicles pollutants it is necessary to take into account the mixture formation and combustion of the working mixture in the internal combustion engine. The article describes the authors' approach to calculating the volumetric flow rate of exhaust gases based on the characteristics of the vehicle's transport operations available for operational control. Studies have shown that, when using a particular fuel, the determination of the volume flow rate of exhaust gases can be reduced to finding the power of the engine . In addition, the composition changes of the fuel (or fuel replacement) and the regulation of the effective power of the engine (by organization of traffic) allow to influence on the volume and composition of the emission of exhaust gases of vehicles and on the pollution of the urban environment in general. The results of the studies make it easier to calculate the mass of pollutant emissions by the transport stream into the outer air and can be used as preliminary data to assess the negative anthropogenic impact on the ecosystem.

Sign in / Sign up

Export Citation Format

Share Document