Large Eddy Simulation of Tandem Blade Stator Cascades

2017 ◽  
Author(s):  
Pratik Mitra ◽  
Jahnavi Kantharaju ◽  
Rohan Rayan ◽  
Joseph Mathew
Keyword(s):  
Boundary Layer ◽  
Leading Edge ◽  
Immersed Boundary ◽  
Surface Boundary ◽  
Suction Surface ◽  
Surface Boundary Layer ◽  
Substantial Impact ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Rapid Transition

Large eddy simulations of tandem blade compressor cascades have been performed with an explicit filtering method. A low speed case was simulated using the public domain code Incompact3d which solves incompressible flow with an immersed boundary method for embedded solid bodies, obviating the effort expended on preparing good quality meshes around blading. The LES successfully captures transition on the front blade and yields a significantly different loading compared with RANS solutions obtained before. The less substantial impact on the rear blade is traced to rapid transition forced by the turbulent wake of the front blade. LES with a refined grid was found to shorten the transition width due to the crucial role of small scales during transition. A complementary study with an in-house compressible LES solver was conducted for a transonic tandem cascade at the inlet Mach number of 0.89. Flow expands around the leading edge of the front blade and is terminated by a shock which interacts with the suction surface boundary layer. The beneficial effect of tandem blading was found to be achieved by limiting this separation. The shock-induced separation also marks a rapid transition of the suction surface boundary layer that is readily captured in the LES, showing pre-transitional streaks, but could prove difficult even for current transition-sensitive RANS.

Leading Edge Contamination of a C-D Compressor Blade Using Large Eddy Simulation

2020 ◽  
Author(s):  
S. Katiyar ◽  
S. Sarkar
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Separation Bubble ◽  
Leading Edge ◽  
Adverse Pressure Gradient ◽  
Suction Surface ◽  
Local Flow ◽  
Flow Acceleration ◽  
Eddy Simulation ◽  
Large Eddy

Abstract A large-eddy simulation (LES) is employed here to predict the flow field over the suction surface of a controlled-diffusion (C-D) compressor stator blade following the experiment of Hobson et al. [1]. When compared with the experiment, LES depicts a separation bubble (SB) in the mid-chord region of the suction surface, although discrepancies exist in Cp. Further, the LES resolves the growth of boundary layer over the mid-chord and levels of turbulence intensity with an acceptable limit. What is noteworthy that LES also resolves a tiny SB near the leading-edge at the designed inflow angle of 38.3°. The objective of the present study is to assess how this leading-edge bubble influences the transition and development of boundary layer on the suction surface before the mid-chord. It appears that the separation at leading-edge suddenly enhances the perturbation levels exciting development of boundary layer downstream. The boundary layer becomes pre-transitional followed by a decay of fluctuations up to 30% of chord attributing to the local flow acceleration. Further, the boundary layer appears like laminar after being relaxed from the leading edge excitation near the mid-chord. It separates again because of the adverse pressure gradient, depicting augmentation of turbulence followed by the breakdown at about 70% of chord.

Low Pressure Turbine Relaminarization Bubble Characterization using Massively-Parallel Large Eddy Simulations

2012 ◽  
Vol 134 (2) ◽  
Author(s):  
Shriram Jagannathan ◽  
Markus Schwänen ◽  
Andrew Duggleby
Keyword(s):  
Boundary Layer ◽  
Reverse Flow ◽  
Leading Edge ◽  
Suction Side ◽  
Low Pressure ◽  
Surface Boundary ◽  
Suction Surface ◽  
Hairpin Vortices ◽  
Low Pressure Turbine ◽  
Large Eddy

The separation and reattachment of suction surface boundary layer in a low pressure turbine is characterized using large-eddy simulation at Ress = 69000 based on inlet velocity and suction surface length. Favorable comparisons are drawn with experiments using a high pass filtered Smagorinsky model for sub-grid scales. The onset of time mean separation is at s/so = 0.61 and reattachment at s/so = 0.81, extending over 20% of the suction surface. The boundary layer is convectively unstable with a maximum reverse flow velocity of about 13% of freestream. The breakdown to turbulence occurs over a very short distance of suction surface and is followed by reattachment. Turbulence near the bubble is further characterized using anisotropy invariant mapping and time orthogonal decomposition diagnostics. Particularly the vortex shedding and shear layer flapping phenomena are addressed. On the suction side, dominant hairpin structures near the transitional and turbulent flow regime are observed. The hairpin vortices are carried by the freestream even downstream of the trailing edge of the blade with a possibility of reaching the next stage. Longitudinal streaks that evolve from the breakdown of hairpin vortices formed near the leading edge are observed on the pressure surface.

scholarly journals Parameterization of Wave-Induced Mixing Using the Large Eddy Simulation (LES) (I)

Atmosphere ◽  
2020 ◽  
Vol 11 (2) ◽  
pp. 207 ◽  
Author(s):  
Haili Wang ◽  
Changming Dong ◽  
Yongzeng Yang ◽  
Xiaoqian Gao
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Ocean Surface ◽  
Breaking Waves ◽  
Global Climate Models ◽  
Surface Boundary ◽  
Surface Boundary Layer ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Wave Induced

Turbulent motions in the thin ocean surface boundary layer control exchanges of momentum, heat and trace gases between the atmosphere and ocean. However, present parametric equations of turbulent motions that are applied to global climate models result in systematic or substantial errors in the ocean surface boundary layer. Significant mixing caused by surface wave processes is missed in most parametric equations. A Large Eddy Simulation model is applied to investigate the wave-induced mixed layer structure. In the wave-averaged equations, wave effects are calculated as Stokes forces and breaking waves. To examine the effects of wave parameters on mixing, a series of wave conditions with varying wavelengths and heights are used to drive the model, resulting in a variety of Langmuir turbulence and wave breaking outcomes. These experiments suggest that wave-induced mixing is more sensitive to wave heights than to the wavelength. A series of numerical experiments with different wind intensities-induced Stokes drifts are also conducted to investigate wave-induced mixing. As the wind speed increases, the influence depth of Langmuir circulation deepens. Additionally, it is observed that breaking waves could destroy Langmuir cells mainly at the sea surface, rather than at deeper layers.

LESbrary: A library of large eddy simulation data for the calibration and uncertainty quantification of ocean surface boundary layer turbulence parameterizations

2021 ◽  
Author(s):  
Gregory Wagner ◽  
Andre Souza ◽  
Adeline Hillier ◽  
Ali Ramadhan ◽  
Raffaele Ferrari
Keyword(s):  
Boundary Layer ◽  
Turbulent Mixing ◽  
Large Scale ◽  
Ocean Surface ◽  
Limited Area ◽  
Surface Boundary ◽  
Model Errors ◽  
Surface Boundary Layer ◽  
Large Eddy ◽  
Free Parameters

<p>Parameterizations of turbulent mixing in the ocean surface boundary layer (OSBL) are key Earth System Model (ESM) components that modulate the communication of heat and carbon between the atmosphere and ocean interior. OSBL turbulence parameterizations are formulated in terms of unknown free parameters estimated from observational or synthetic data. In this work we describe the development and use of a synthetic dataset called the “LESbrary” generated by a large number of idealized, high-fidelity, limited-area large eddy simulations (LES) of OSBL turbulent mixing. We describe how the LESbrary design leverages a detailed understanding of OSBL conditions derived from observations and large scale models to span the range of realistically diverse physical scenarios. The result is a diverse library of well-characterized “synthetic observations” that can be readily assimilated for the calibration of realistic OSBL parameterizations in isolation from other ESM model components. We apply LESbrary data to calibrate free parameters, develop prior estimates of parameter uncertainty, and evaluate model errors in two OSBL parameterizations for use in predictive ESMs.</p>

Boundary Layer Development in the BR710 and BR715 LP Turbines—The Implementation of High-Lift and Ultra-High-Lift Concepts

2002 ◽  
Vol 124 (3) ◽  
pp. 385-392 ◽  
Author(s):  
R. J. Howell ◽  
H. P. Hodson ◽  
V. Schulte ◽  
R. D. Stieger ◽  
Heinz-Peter Schiffer ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Test Facility ◽  
Surface Boundary ◽  
Unsteady Boundary Layer ◽  
Suction Surface ◽  
High Lift ◽  
Surface Boundary Layer ◽  
Cold Flow ◽  
Layer Behavior ◽  
Lp Turbine

This paper describes a detailed study into the unsteady boundary layer behavior in two high-lift and one ultra-high-lift Rolls-Royce Deutschland LP turbines. The objectives of the paper are to show that high-lift and ultra-high-lift concepts have been successfully incorporated into the design of these new LP turbine profiles. Measurements from surface mounted hot film sensors were made in full size, cold flow test rigs at the altitude test facility at Stuttgart University. The LP turbine blade profiles are thought to be state of the art in terms of their lift and design philosophy. The two high-lift profiles represent slightly different styles of velocity distribution. The first high-lift profile comes from a two-stage LP turbine (the BR710 cold-flow, high-lift demonstrator rig). The second high-lift profile tested is from a three-stage machine (the BR715 LPT rig). The ultra-high-lift profile measurements come from a redesign of the BR715 LP turbine: this is designated the BR715UHL LP turbine. This ultra-high-lift profile represents a 12 percent reduction in blade numbers compared to the original BR715 turbine. The results from NGV2 on all of the turbines show “classical” unsteady boundary layer behavior. The measurements from NGV3 (of both the BR715 and BR715UHL turbines) are more complicated, but can still be broken down into classical regions of wake-induced transition, natural transition and calming. The wakes from both upstream rotors and NGVs interact in a complicated manner, affecting the suction surface boundary layer of NGV3. This has important implications for the prediction of the flows on blade rows in multistage environments.

Large Eddy Simulation of Wake-Shear Layer Interactions Over a Multi-Element Aerofoil

2020 ◽  
Author(s):  
Souvik Naskar ◽  
S. Sarkar
Keyword(s):  
Large Eddy Simulation ◽  
Shear Layer ◽  
Separation Bubble ◽  
Turbine Blades ◽  
Leading Edge ◽  
Aerodynamic Characteristics ◽  
Suction Surface ◽  
Free Stream Turbulence ◽  
Eddy Simulation ◽  
Large Eddy

Abstract Modern commercial airliners use multi-element aerofoils to enhance take-off and landing performance. Further, multielement aerofoil configurations have been shown to improve the aerodynamic characteristics of wind turbines. In the present study, high resolution Large Eddy Simulation (LES) is used to explore the low Reynolds Number (Re = 0.832 × 104) aerodynamics of a 30P30N multi-element aerofoil at an angle of attack, α = 4°. In the present simulation, wake shed from a leading edge element or slat is found to interact with the separated shear layer developing over the suction surface of the main wing. High receptivity of shear layer via amplification of free-stream turbulence leads to rollup and breakdown, forming a large separation bubble. A transient growth of fluctuations is observed in the first half of the separation bubble, where levels of turbulence becomes maximum near the reattachment and then decay depicting saturation of turbulence. Results of the present LES are found to be in close agreement with the experiment depicting high vortical activity in the outer layer. Some features of the flow field here are similar to those occur due to interactions of passing wake and the separated boundary layer on the suction surface of high lift low pressure turbine blades.

Large Eddy Simulation of Boundary Layer Transition Mechanisms in a Gas-Turbine Compressor Cascade

2018 ◽  
Author(s):  
Ashley D. Scillitoe ◽  
Paul G. Tucker ◽  
Paolo Adami
Keyword(s):  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Boundary Layer Transition ◽  
Bypass Transition ◽  
Suction Surface ◽  
Layer Transition ◽  
Turbulent Spots ◽  
Pressure Surface ◽  
Eddy Simulation ◽  
Large Eddy

Large Eddy Simulation (LES) is used to explore the boundary layer transition mechanisms in two rectilinear compressor cascades. To reduce numerical dissipation, a novel locally adaptive smoothing scheme is added to an unstructured finite-volume solver. The performance of a number of Sub-Grid Scale (SGS) models is explored. With the first cascade, numerical results at two different freestream turbulence intensities (Ti’s), 3.25% and 10%, are compared. At both Ti’s, time-averaged skin-friction and pressure coefficient distributions agree well with previous Direct Numerical Simulations (DNS). At Ti = 3.25%, separation induced transition occurs on the suction surface, whilst it is bypassed on the pressure surface. The pressure surface transition is dominated by modes originating from the convection of Tollmien-Schlichting waves by Klebanoff streaks. However, they do not resembled a classical bypass transition. Instead, they display characteristics of the “overlap” and “inner” transition modes observed in the previous DNS. At Ti = 10%, classical bypass transition occurs, with Klebanoff streaks incepting turbulent spots. With the second cascade, the influence of unsteady wakes on transition is examined. Wake-amplified Klebanoff streaks were found to instigate turbulent spots, which periodically shorten the suction surface separation bubble. The celerity line corresponding to 70% of the free-stream velocity, which is associated with the convection speed of the amplified Klebanoff streaks, was found to be important.

Large Eddy Simulation of the Laminar Heat Transfer Augmentation on the Pressure Side of a Turbine Vane Under Freestream Turbulence

2019 ◽  
Vol 141 (4) ◽  
Author(s):  
Yousef Kanani ◽  
Sumanta Acharya ◽  
Forrest Ames
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Leading Edge ◽  
Transition To Turbulence ◽  
Experimental Measurements ◽  
Pressure Side ◽  
Freestream Turbulence ◽  
Heat Transfer Augmentation ◽  
Eddy Simulation ◽  
Large Eddy

Vane pressure side heat transfer is studied numerically using large eddy simulation (LES) on an aft-loaded vane with a large leading edge over a range of turbulence conditions. Numerical simulations are performed in a linear cascade at exit chord Reynolds number of Re = 5.1 × 105 at low (Tu ≈ 0.7%), moderate (Tu ≈ 7.9%), and high (Tu ≈ 12.4%) freestream turbulence with varying length scales as prescribed by the experimental measurements of Varty and Ames (2016, “Experimental Heat Transfer Distributions Over an Aft Loaded Vane With a Large Leading Edge at Very High Turbulence Levels,” ASME Paper No. IMECE2016-67029). Heat transfer predictions on the vane pressure side are in a very good agreement with the experimental measurements and the heat transfer augmentation due to the freestream turbulence is well captured. At Tu ≈ 12.4%, freestream turbulence enhances the Stanton number on the pressure surface without boundary layer transition to turbulence by a maximum of about 50% relative to the low freestream turbulence case. Higher freestream turbulence generates elongated structures and high-velocity streaks wrapped around the leading edge that contain significant energy. Amplification of the velocity streaks is observed further downstream with max rms of 0.3 near the trailing edge but no transition to turbulence or formation of turbulence spots is observed on the pressure side. The heat transfer augmentation at the higher freestream turbulence is primarily due to the initial amplification of the low-frequency velocity perturbations inside the boundary layer that persist along the entire chord of the airfoil. Stanton numbers appear to scale with the streamwise velocity fluctuations inside the boundary layer.

Large Eddy Simulation of Bypass Transition in Vane Passage With Freestream Turbulence

2020 ◽  
Vol 142 (6) ◽  
Author(s):  
Yousef Kanani ◽  
Sumanta Acharya ◽  
Forrest Ames
Keyword(s):  
Heat Transfer ◽  
Boundary Layer ◽  
Large Eddy Simulation ◽  
Bypass Transition ◽  
Freestream Turbulence ◽  
Turbulent Spot ◽  
Suction Surface ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Inflow Turbulence

Abstract High Reynolds flow over a nozzle guide-vane with elevated inflow turbulence was simulated using wall-resolved large eddy simulation (LES). The simulations were undertaken at an exit Reynolds number of 0.5 × 106 and inflow turbulence levels of 0.7% and 7.9% and for uniform heat-flux boundary conditions corresponding to the measurements of Varty and Ames (2016, “Experimental Heat Transfer Distributions Over an Aft Loaded Vane With a Large Leading Edge at Very High Turbulence Levels,” ASME Paper No. IMECE2016-67029). The predicted heat transfer distribution over the vane is in excellent agreement with measurements. At higher freestream turbulence, the simulations accurately capture the laminar heat transfer augmentation on the pressure surface and the transition to turbulence on the suction surface. The bypass transition on the suction surface is preceded by boundary layer streaks formed under the external forcing of freestream disturbances which breakdown to turbulence through inner-mode secondary instabilities. Underneath the locally formed turbulent spot, heat transfer coefficient spikes and generally follows the same pattern as the turbulent spot. The details of the flow and temperature fields on the suction side are characterized, and first- and second-order statistics are documented. The turbulent Prandtl number in the boundary layer is generally in the range of 0.7–1, but decays rapidly near the wall.

Sign in / Sign up

Export Citation Format

Share Document