A Study of Steam-Cooled Humidified Gas Turbine Cycles

2011 ◽  
Author(s):  
Ching-Jen C. J. Tang
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Pressure Ratio ◽  
Combustion Stability ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Electrical Efficiency ◽  
Percentage Points ◽  
Steam Cooling ◽  
Power Outputs

Humidified Gas Turbine (HGT) cycles such as the Evaporative Gas Turbine (EGT) and the Steam-Injected Gas Turbine (STIG) using humid air as the working medium do not require a complete steam turbine bottoming cycle; thus, their initial capital costs are not as high as those for the conventional combined cycles. The performance of a HGT cycle could be comparable to a state-of-the-art combined cycle for small loads. The availability of the steam from a HGT cycle presents opportunities for designing steam-cooled blades. Since the specific heat capacity for steam is higher than that for air, steam could potentially be a better coolant for turbine blades than air, resulting in higher cycle efficiency. In this study, three known HGT cycles are evaluated in terms of their electrical efficiencies and power outputs: the STIG, the Part-flow Evaporative Gas Turbine (PEvGT), and the combined STIG cycles. All the three HGT cycles are analyzed in two cooling options: steam and air coolings. The HGT cycles will be evaluated using consistent thermodynamic properties and assumptions. Like a simple gas turbine cycle, the HGT cycles are based on the well-known Brayton cycle whose performance is dictated by the cycle pressure ratio and turbine inlet temperature. Therefore, the electrical efficiencies and power outputs of the HGT cycles will be calculated as a function of the cycle pressure ratio and turbine inlet temperature. The steam-cooled cycles provide advantages over the air-cooled cycles in the electrical efficiency, power output, and combustion stability. The steam cooling improves the electrical efficiency by approximately 1.4 percentage points for the STIG cycle, by approximately 1.7 percentage points for the PEvGT cycle, and by approximately 1 percentage point for the combined STIG cycle. The maximum electrical efficiency of the steam-cooled PEvGT cycle is 54.6%, only 0.2 percentage points higher than that for the steam-cooled combined STIG cycle. The steam cooling generally results in more power output than the air cooling does for all the HGT cycles at most operating conditions. In addition, the steam cooling reduces the water content of the humid air entering the combustor, leading to significantly improved combustion stability.

scholarly journals Implementation of Adaptive Neuro-fuzzy Model to Optimize Operational Process of Multiconfiguration Gas-Turbines

2020 ◽  
Vol 2020 ◽  
pp. 1-17
Author(s):  
Chao Deng ◽  
Ahmed N. Abdalla ◽  
Thamir K. Ibrahim ◽  
MingXin Jiang ◽  
Ahmed T. Al-Sammarraie ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Power Output ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Anfis Model ◽  
Neuro Fuzzy ◽  
Compressor Efficiency

In this article, the adaptive neuro-fuzzy inference system (ANFIS) and multiconfiguration gas-turbines are used to predict the optimal gas-turbine operating parameters. The principle formulations of gas-turbine configurations with various operating conditions are introduced in detail. The effects of different parameters have been analyzed to select the optimum gas-turbine configuration. The adopted ANFIS model has five inputs, namely, isentropic turbine efficiency (Teff), isentropic compressor efficiency (Ceff), ambient temperature (T1), pressure ratio (rp), and turbine inlet temperature (TIT), as well as three outputs, fuel consumption, power output, and thermal efficiency. Both actual reported information, from Baiji Gas-Turbines of Iraq, and simulated data were utilized with the ANFIS model. The results show that, at an isentropic compressor efficiency of 100% and turbine inlet temperature of 1900 K, the peak thermal efficiency amounts to 63% and 375 MW of power resulted, which was the peak value of the power output. Furthermore, at an isentropic compressor efficiency of 100% and a pressure ratio of 30, a peak specific fuel consumption amount of 0.033 kg/kWh was obtained. The predicted results reveal that the proposed model determines the operating conditions that strongly influence the performance of the gas-turbine. In addition, the predicted results of the simulated regenerative gas-turbine (RGT) and ANFIS model were satisfactory compared to that of the foregoing Baiji Gas-Turbines.

A Parametric Analysis for Optimal Selection of a Gas Turbine Cogeneration System

2004 ◽  
Author(s):  
K. Sarabchi ◽  
A. Ansari
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Computer Code ◽  
Primary Energy ◽  
Inlet Temperature ◽  
Fuel Cost ◽  
Energy Usage ◽  
Turbine Inlet Temperature ◽  
Cogeneration System ◽  
Selection Of

Cogeneration is a simultaneous production of heat and electricity in a single plant using the same primary energy. Usage of a cogeneration system leads to fuel energy saving as well as air pollution reduction. A gas turbine cogeneration plant (GTCP) has found many applications in industries and institutions. Although fuel cost is usually reduced in a cogeneration system but the selection of a system for a given site optimally involves detailed thermodynamic and economical investigations. In this paper the performance of a GTCP was investigated and an approach was developed to determine the optimum size of the plant to meet the electricity and heat demands of a given site. A computer code, based on this approach, was developed and it can also be used to examine the effect of key parameters like pressure ratio, turbine inlet temperature, utilization period, and fuel cost on the economics of GTCP.

Proposal of Innovative Gas Turbine Combined Cycle Power Generation System

2004 ◽  
Author(s):  
Hideto Moritsuka
Keyword(s):  
Power Generation ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Combined Cycle ◽  
Inlet Temperature ◽  
Generation System ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet ◽  
Power Generation System

In order to estimate the possibility to improve thermal efficiency of power generation use gas turbine combined cycle power generation system, benefits of employing the advanced gas turbine technologies proposed here have been made clear based on the recently developed 1500C-class steam cooling gas turbine and 1300C-class reheat cycle gas turbine combined cycle power generation systems. In addition, methane reforming cooling method and NO reducing catalytic reheater are proposed. Based on these findings, the Maximized efficiency Optimized Reheat cycle Innovative Gas Turbine Combined cycle (MORITC) Power Generation System with the most effective combination of advanced technologies and the new devices have been proposed. In case of the proposed reheat cycle gas turbine with pressure ratio being 55, the high pressure turbine inlet temperature being 1700C, the low pressure turbine inlet temperature being 800C, combined with the ultra super critical pressure, double reheat type heat recovery Rankine cycle, the thermal efficiency of combined cycle are expected approximately 66.7% (LHV, generator end).

Design Details of a 600 MW Graz Cycle Thermal Power Plant for CO2 Capture

2008 ◽  
Author(s):  
H. Jericha ◽  
W. Sanz ◽  
E. Go¨ttlich ◽  
F. Neumayer
Keyword(s):  
Vortex Flow ◽  
Pressure Ratio ◽  
Thermal Power ◽  
Inlet Temperature ◽  
Turbine Stage ◽  
Turbine Inlet Temperature ◽  
Coal Gas ◽  
Transonic Compressor ◽  
Steam Cooling ◽  
Important Design

The high power highest efficiency zero-emission Graz Cycle plant of 400 MW was presented at ASME IGTI conference 2006 and at CIMAC conference 2007. In continuation of these works a raise of power output to 600 MW is presented and important design details are discussed. The cycle pressure ratio is increased from 40 to 50 bar by a half-speed stage connected via gears to the main compressor shaft allowing to keep the volume flow to the main compressors constant. The compressors are driven by the transonic compressor turbine stage. Mass flow to the compressors is increased by the factor of 1.27, density in blades of the main compressors is raised by the same factor. The turbine inlet temperature is raised to 1500°C together with the increase in the cycle pressure ratio, both are well accepted values in gas turbine technology today. Most important development problems have to be solved in designing the oxy-fuel burners. They are presented here in the form of coaxial jets of fuel (natural gas or coal gas alternatively) held together by a steam vortex providing coherent flow and flame is ignited by its strong suction. Combustion is finalized by the mixing with a counter-rotating outer vortex flow of working gas leading to a well defined position of vortex break down. The transonic stage of the compressor turbine is supplied with innovative steam cooling forming coherent layers outside of the blade shell of which stress deliberations will be presented.

scholarly journals Cooling Process of Gas Turbine Blade: A Comparison Study

2020 ◽  
Vol 13 (3) ◽  
pp. 215-222
Author(s):  
Akram Luaibi Ballaoot ◽  
Naseer Hamza
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Power Output ◽  
Film Cooling ◽  
Aviation Industry ◽  
Inlet Temperature ◽  
Internal Cooling ◽  
Gas Turbine Blade ◽  
Turbine Inlet Temperature ◽  
Turbine Inlet

The gas turbine engines are occupied an important sector in the energy production and aviation industry and this important increase day after day for their features. One of the most important parameters that limit the gas turbine engine power output is the turbine inlet temperature. The higher is the turbine inlet temperature, the higher is the power output or thrust but this increases of risks of blade thermal failure due to metallurgical limits. Thus the need for a good and efficient process of blade cooling can lead to the best compromise between a powerful engine and safe operation. There are two major methods: film or external cooling and internal cooling inside the blade itself. . In the past number of years there has been considerable progress in turbine cooling research and this paper is limited to review a few selected publications to reflect recent development in turbine blade film cooling. The maximum drop in the surface temperature of the gas turbine blade and associated thermal stress – due to incorporating cooling systems- were 735 ˚C, 1217 N/mm2 respectively.

scholarly journals 100s and 1000s Mw Open and Semi-Closed Cycle Gas Turbines for Base and Peak Operation

1974 ◽  
Author(s):  
V. V. Uvarov ◽  
V. S. Beknev ◽  
E. A. Manushin
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Pressure Ratio ◽  
Simple Cycle ◽  
Inlet Temperature ◽  
Closed Cycle ◽  
Turbine Inlet Temperature ◽  
Unit Capacity ◽  
Temperature And Pressure ◽  
Different Levels

There are two different approaches to develop the gas turbines for power. One can get some megawatts by simple cycle or by more complex cycle units. Both units require very different levels of turbine inlet temperature and pressure ratio for the same unit capacity. Both approaches are discussed. These two approaches lead to different size and efficiencies of gas turbine units for power. Some features of the designing problems of such units are discussed.

A 2000-HP Military Vehicle Gas Turbine: A Study of Significant Thermodynamic and Mechanical Parameters

1968 ◽  
Author(s):  
A. F. Carter
Keyword(s):  
Gas Turbine ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Overall Design ◽  
Blade Cooling ◽  
Turbine Inlet ◽  
Military Vehicle ◽  
Compressor Pressure Ratio ◽  
Selection Of

During a study of possible gas turbine cycles for a 2000-hp unit for tank propulsion, it has been established that the level of achievable specific fuel consumption (sfc) is principally determined by the combustor inlet temperature. If a regenerative cycle is selected, a particular value of combustor inlet temperature (and hence sfc) can be produced by an extremely large number of combinations of compressor pressure ratio, turbine inlet temperature, and heat exchanger effectiveness. This paper outlines the overall design considerations which led to the selection of a relatively low pressure ratio engine in which the turbine inlet temperature was sufficiently low that blade cooling was not necessary.

Research and Development of 300kW Class Ceramic Gas Turbine (Development of the Static Ceramic Components for CGT303)

1995 ◽  
Author(s):  
Mitsuharu Murota ◽  
Issei Ohhashi ◽  
Yoshiyuki Ito ◽  
Sadao Arakawa
Keyword(s):  
Research And Development ◽  
Gas Turbine ◽  
Pressure Ratio ◽  
Important Task ◽  
Inlet Temperature ◽  
Gas Temperature ◽  
Turbine Inlet Temperature ◽  
Engine Operation ◽  
Heat Cycle ◽  
Ceramic Components

As the result of setting the low pressure ratio at 4.5, sizes of the static ceramic components forming the gas passage in CGT303 have been increased, and establishing reliability of these components was thought to be the most important task. So, the heat-cycle tests were conducted, in advance of the engine operation, and improvements have been made on their material and constructions. After conducting 600 times of the heat-cycle tests, so far, up to the gas temperature of 1200°C, we have succeeded in the engine operation at the turbine inlet temperature of 1200°C Examples of the problems encountered in the test and of the solutions therefore are introduced in this paper.

Comparative Thermodynamic Analysis of Gas Turbine Systems with Turbine Blade Film Cooling

2012 ◽  
Vol 505 ◽  
pp. 539-543
Author(s):  
Kyoung Hoon Kim ◽  
Kyoung Jin Kim ◽  
Chul Ho Han
Keyword(s):  
Gas Turbine ◽  
Turbine Blade ◽  
Thermodynamic Analysis ◽  
Film Cooling ◽  
Pressure Ratio ◽  
Turbine Blades ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Blade Cooling ◽  
Turbine Inlet

Since the gas turbine systems require active cooling to maintain high operating temperature while avoiding a reduction in the system operating life, turbine blade cooling is very important and essential but it may cause the performance losses in gas turbine. This paper deals with the comparative thermodynamic analysis of gas turbine system with and without regeneration by using the recently developed blade-cooling model when the turbine blades are cooled by the method of film cooling. Special attention is paid to investigating the effects of system parameters such as pressure ratio and turbine inlet temperature on the thermodynamic performance of the systems. In both systems the thermal efficiency increases with turbine inlet temperature, but its effect is less sensitive in simpler system

scholarly journals Exergy, economic and environmental (3E) analysis of a gas turbine power plant and optimization by MOPSO algorithm

2018 ◽  
Vol 22 (6 Part A) ◽  
pp. 2641-2651 ◽  
Author(s):  
Moein Shamoushaki ◽  
Mehdi Ehyaei
Keyword(s):  
Gas Turbine ◽  
Co2 Emission ◽  
Emission Rate ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
Turbine Inlet Temperature ◽  
Total Cost ◽  
Cost Rate ◽  
Turbine Inlet ◽  
Compressor Pressure Ratio

In this paper, exergy, exergoeconomic, and exergoenvironmental analysis of a gas turbine cycle and its optimization has been carried out by MOPSO algorithm. Three objective functions, namely, total cost rate, exergy efficiency of cycle, and CO2 emission rate have been considered. The design variables considered are: compressor pressure ratio, combustion chamber inlet temperature, gas turbine inlet temperature, compressor, and gas turbine isentropic efficiency. The impact of change in gas turbine inlet temperature and compressor pressure ratio on CO2 emission rate as well as impact of changes in gas turbine inlet temperature on exergy efficiency of the cycle has been investigated in different compressor pressure ratios. The results showed that with increase in compressor pressure ratio and gas turbine inlet temperature, CO2 emission rate decreases, that is this reduction is carried out with a steeper slope at lower pressure compressor ratio and gas turbine inlet temperature. The results showed that exergy efficiency of the cycle increases with increase in gas turbine inlet temperature and compressor pressure ratio. The sensitivity analysis of fuel cost changes was performed on objective functions. The results showed that at higher exergy efficiencies total cost rate is greater, and sensitivity of fuel cost optimum solutions is greater than Pareto curve with lower total cost rate. Also, the results showed that sensitivity of changes in fuel cost rate per unit of energy on total cost rate is greater than the rate of CO2 emission.

Sign in / Sign up

Export Citation Format

Share Document