Characteristics of Bluff Body Stabilized Turbulent Premixed Flames

2011 ◽  
Author(s):  
Alejandro M. Briones ◽  
Balu Sekar ◽  
Hugh Thornburg
Keyword(s):  
Bluff Body ◽  
Three Dimensional ◽  
Leading Edge ◽  
Reacting Flows ◽  
Chemical Mechanism ◽  
Reacting Flow ◽  
Bluff Bodies ◽  
Two Dimensional ◽  
Aspect Ratios ◽  
Trailing Edges

Non-reacting and reacting flows past typical flameholders are modeled with URANS and LES. The continuity, momentum, energy, species, and turbulence governing equations are solved using two- and three-dimensional configurations. Either 2-step global or 44-step reduced chemical mechanism for C3H8-air combustion, accounting for turbulence-chemistry interaction, and with temperature- and species-dependent thermodynamic and transport properties is utilized. For square and rectangular bluff bodies the flow separates at the leading edges, whereas for triangular bluff body separation occurs only at the trailing edges. These bluff bodies exhibit two shear layers at the trailing edges that shed asymmetric vortices. For rectangular bluff bodies with aspect ratios (AR) less than 2.3 there is backflow from the wake. With increasing AR from unity, backflow is gradually diminished, and the von Ka´rma´n Strouhal number (StvK) decreases. For 2.0<AR<2.3, StvK jumps to a higher value and separation again occurs at the trailing edges for AR = 2.3. Further increase in AR decreases StvK again. The simulations with URANS qualitatively and quantitatively match experimental results for StvK vs. AR. Quantitative discrepancies are, however, found for AR≥2.3. In addition, two-dimensional non-reacting flows with URANS are sufficient to predict StvK. Moreover, two-dimensional simulations of reacting flow indicate that the flame promotes static and dynamic stability for AR = 1.0 and 2.3. The flame is dynamically unstable for AR = 2.0, exhibiting a von Ka´rma´n flow pattern. Stable flames anchored at the most downstream separation location (e.g., the flame anchored at AR = 1.0 is attached to the leading edge, whereas that of AR = 2.3 is attached to the trailing edge). Realizable k-ε URANS and LES simulations for the triangular cylinder closely match the experimental StvK for both non-reacting and reacting flows. Nonetheless, LES predicts a smaller recirculation length than k-ε URANS. LES predicts a flow field in which Be´rnard/von Ka´rma´n (BvK) instability is suppressed, whereas URANS predicts a competition between the Kelvin-Helmholtz (KH) instability and BvK.

Interaction and acoustics of separated flows from a D-shaped bluff body

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Guangyuan Huang ◽  
Ka Him Seid ◽  
Zhigang Yang ◽  
Randolph Chi Kin Leung
Keyword(s):  
Vortex Shedding ◽  
Bluff Body ◽  
Leading Edge ◽  
Separated Flows ◽  
Pressure Waves ◽  
Bluff Bodies ◽  
Trailing Edge ◽  
Content Type ◽  
Trailing Edges ◽  
Edge Vortex

Purpose For flow around elongated bluff bodies, flow separations would occur over both leading and trailing edges. Interactions between these two separations can be established through acoustic perturbation. In this paper, the flow and the acoustic fields of a D-shaped bluff body (length-to-height ratio L/H = 3.64) are investigated at height-based Reynolds number Re = 23,000 by experimental and numerical methods. The purpose of this paper is to study the acoustic feedback in the interaction of these two separated flows. Design/methodology/approach The flow field is measured by particle image velocimetry, hotwire velocimetry and surface oil flow visualization. The acoustic field is modeled in two dimensions by direct aeroacoustic simulation, which solves the compressible Navier–Stokes equations. The simulation is validated against the experimental results. Findings Separations occur at both the leading and the trailing edges. The leading-edge separation point and the reattaching flow oscillate in accordance with the trailing-edge vortex shedding. Significant pressure waves are generated at the trailing edge by the vortex shedding rather than the leading-edge vortices. Pressure-based cross-correlation analysis is conducted to clarify the effect of the pressure waves on the leading-edge flow structures. Practical implications The understanding of interactions of separated flows over elongated bluff bodies helps to predict aerodynamic drag, structural vibration and noise in engineering applications, such as the aerodynamics of buildings, bridges and road vehicles. Originality/value This paper clarifies the influence of acoustic perturbations in the interaction of separated flows over a D-shaped bluff body. The contribution of the leading- and the trailing-edge vortex in generating acoustic perturbations is investigated as well.

Aerodynamic behaviour of bodies in the wakes of other bodies

1971 ◽  
Vol 269 (1199) ◽  
pp. 425-437 ◽  
Keyword(s):  
Bluff Body ◽  
Three Dimensional ◽  
Future Research ◽  
Bluff Bodies ◽  
Two Dimensional ◽  
Limited Information ◽  
Irrotational Flow ◽  
Two Bodies

Wakes of two-dimensional bluff bodies are described, with emphasis on the properties of the wake which influence the loads on other bodies placed in the wake. The unsteady irrotational flow outside the true wake is included in the discussion. Some limited information on the wakes of three-dimensional bluff bodies is also considered. The interaction between two bodies is subdivided into two categories: (i) when the bodies are close together and the upstream body is influenced by the downstream one and (ii) when the bodies are so far apart that only the downstream body is affected. Experiments are described in which the load on an aerofoil in the wake of a two-dimensional bluff body was measured. The results are presented in the form of an aerodynamic admittance and these experiments are used to illustrate the type of problem associated with the determination of the loads on a bluff body in a wake. Experiments are also described which show the large variation of time-averaged load which can be developed on a body which is part of a closely packed complex of bodies, as the orientation of the complex to the wind is varied. Finally, some ideas for future research are outlined.

Computational and Neuro-Fuzzy Study of the Effect of Small Objects on the Flow and Thermal Fields of Bluff Bodies

2006 ◽  
Author(s):  
Ahmed F. Abdel Gawad
Keyword(s):  
Drag Reduction ◽  
Bluff Body ◽  
Three Dimensional ◽  
The Body ◽  
Bluff Bodies ◽  
Small Object ◽  
Two Dimensional ◽  
Neuro Fuzzy ◽  
Body Cooling ◽  
Two Dimensional Flows

The aim of the present study is to find computationally the optimum parameters that affect the drag reduction of bluff bodies using a small object (obstacle). These parameters include the size of the obstacle as well as the gap between the obstacle and the bluff body. Two- and three-dimensional bodies were investigated in turbulent flow fields. The research was focused on the cases of the rectangular-section obstacle. Four values of the obstacle size were studied, namely: 4%, 10%, 35%, and 100% of the size of the bluff body. The effect of the obstacle on the thermal field of the two-dimensional body was also studied. Comparisons were carried out with the available experimental measurements. A proposed neuro-fuzzy approach was used to predict the drag reduction of the entire system. Results showed that system drag reductions up to 62% (two-dimensional flows) and 48% (three-dimensional flows) can be obtained. Also, enhancement of the body cooling up to 75% (two-dimensional flows) may be achieved. Generally, useful comments and suggestions are stated.

scholarly journals Three-dimensional theory on supercavitating hydrofoils near a free surface

1975 ◽  
Vol 71 (2) ◽  
pp. 339-359 ◽  
Author(s):  
Okitsugu Furuya
Keyword(s):  
Free Surface ◽  
Aspect Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Reference Level ◽  
Two Dimensional ◽  
Large Aspect Ratio ◽  
Dimensional Solution ◽  
Aspect Ratios ◽  
Lifting Line

Supercavitating hydrofoils of large aspect ratio operating near a free surface are investigated, assuming an inviscid and irrotational flow with the effects of gravity and surface tension neglected. The flow near the foil, treated as two-dimensional, is solved by a nonlinear free-streamline theory, then a three-dimensional ‘downwash’ correction is made using Prandtl's lifting-line theory. The strength of the lifting-line vortex is determined by information from the two-dimensional solution through a matching procedure, in which the inverse of aspect ratio is used as a small parameter for asymptotic expansions. The analysis incorporates a free-surface reference level to determine the submergence depth of the foil. The present method can be applied to any type of foil having an arbitrary planform or profile shape, including a rounded leading edge, a twist and even a small dihedral angle, within the assumption of large aspect ratio. Numerical computations made on rectangular flat-plate hydrofoils show excellent agreement of results with existing experimental data, even for large angles of attack and relatively low aspect ratios. The pressure distributions, shapes of the cavity and free surface are also calculated as a function of spanwise position.

Simulation of Two-Dimensional Turbulent Recirculating Flow Field Behind a V-Shaped Bluff Body

1994 ◽  
Author(s):  
Z. Gu ◽  
M. A. R. Sharif
Keyword(s):  
Flow Field ◽  
Bluff Body ◽  
Flame Stabilization ◽  
Bluff Bodies ◽  
Two Dimensional ◽  
Combustion Chambers ◽  
Recirculating Flow ◽  
Conservative Form ◽  
Curvilinear Grid ◽  
Predictor Corrector

Abstract The two-dimensional turbulent recirculating flow fields behind a V-shaped bluff body have been investigated numerically. Similar bluff bodies are used in combustion chambers for flame stabilization. The governing transport equations in conservative form are solved by a pressure based predictor-corrector method. The standard k-ϵ turbulence closure model and a boundary fitted multi-block curvilinear grid system are used in the computation. The code is validated against turbulent flow over a backward facing step problem. The predicted flow field behind the bluff body is also compared with experiment. It is found that while the qualitative features of the flow are well predicted, there is quantitative disagreement between the measurement and prediction. This disagreement can be partially attributed to the k-ϵ turbulence model which is known to be inadequate for recirculating flows. Parametric investigation of the flow field by varying the shape and size of the bluff body is also performed and the results are reported.

A New Approach to Thin Aerofoil Theory

1951 ◽  
Vol 3 (3) ◽  
pp. 193-210 ◽  
Author(s):  
M.J. Lighthill
Keyword(s):  
Three Dimensional ◽  
Leading Edge ◽  
Approximate Solutions ◽  
Radius Of Curvature ◽  
Two Dimensional ◽  
General Technique ◽  
New Approach ◽  
Flow Problems ◽  
Physical Problems ◽  
First Approximation

SummaryThe general technique for rendering approximate solutions to physical problems uniformly valid is here applied to the simplest form of the problem of correcting the theory of thin wings near a rounded leading edge. The flow investigated is two-dimensional, irrotational and incompressible, and therefore the results do not materially add to our already extensive knowledge of this subject, but the method, which is here satisfactorily checked against this knowledge, shows promise of extension to three-dimensional, and compressible, flow problems.The conclusion, in the problem studied here, is that the velocity field obtained by a straightforward expansion in powers of the disturbances, up to and including either the first or the second power, with coefficients functions of co-ordinates such that the leading edge is at the origin and the aerofoil chord is one of the axes, may be rendered a valid first approximation near the leading edge, as well as a valid first or second approximation away from it, if the whole field is shifted downstream parallel to the chord for a distance of half the leading edge radius of curvature ρL. It follows that the fluid speed on the aerofoil surface, as given on such a straightforward second approximation as a function of distance x along the chord, similarly is rendered uniformly valid (see equation (52)) if the part singular like x-1 is subtracted and the remainder is multiplied by .

The Effect of Aspect Ratio on Wall Pressure Fluctuations at a Wing-Plate Junction

2020 ◽  
Vol 142 (7) ◽  
Author(s):  
M. Awasthi ◽  
J. Rowlands ◽  
D. J. Moreau ◽  
C. J. Doolan
Keyword(s):  
Pressure Fluctuations ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Wide Frequency Range ◽  
Wall Pressure ◽  
Frequency Range ◽  
Three Dimensional Flow ◽  
Wall Pressure Fluctuations ◽  
Aspect Ratios

Abstract Measurements of the wall pressure fluctuations near a wing-plate junction were made for wings with three different aspect ratios (AR) of 0.2, 0.5, and 1.0 at several angles of attack. The chord-based Reynolds number for each wing was 274,000. The results show that the wall pressure fluctuations are a function of wing AR for cases where AR≤ 1.0. For each wing, the pressure fluctuations are highest upstream of the wing leading-edge due to three-dimensional flow separation; wings with AR = 1.0 and 0.5 show comparable levels, while those with AR = 0.2 show lower fluctuation levels over a wide frequency range. Downstream of the leading-edge, the pressure fluctuations decay rapidly on both sides of the wing until the maximum thickness location after which little variation is observed. The pressure fluctuations downstream of the leading-edge on the suction-side were observed to be comparable for AR = 0.2 and 0.5, while those for AR = 1.0 were higher in magnitude. On the pressure-side, the pressure fluctuations near the leading-edge are a weak function of AR; however, those further downstream remain independent of AR. The pressure fluctuations aft of the wing on the suction-side are more coherent for lower ARs and show higher convection velocity, possibly due to an interaction between the tip and the junction flows for lower ARs.

Computation of 3D Turbulent Not-Premixed Reacting Flows Using an Implicit Unstructured Solver

2000 ◽  
Author(s):  
P. Adami ◽  
F. Martelli
Keyword(s):  
Bluff Body ◽  
Cfd Simulation ◽  
Turbulent Flame ◽  
Steady State Solution ◽  
Reacting Flows ◽  
Tvd Scheme ◽  
Reacting Flow ◽  
Riemann Solver ◽  
Turbulent Reactive Flows ◽  
Volume Method

A 3D CFD simulation of turbulent reactive flows is discussed. The original compressible version of the solver HybFlow designed for turbine rows investigation is here applied for low speed burning flow. A conserved scalar approach is considered to simulate the turbulent reacting flow field of non-premixed flames. The spatial discretization is based on an upwind finite volume method for unstructured grids using the Roe’s Riemann solver with a non-linear TVD scheme. The steady state solution is computed by means of an implicit relaxed Newton method. The linear solver is GMRES coupled with an ILU(0) preconditioning scheme. The turbulence chemistry interaction is described using a presumed β-PDF Flamelet approach. Two test applications are here presented to verify the methodology characteristics for a pilot-jet turbulent flame and a bluff-body stabilized flame both using CH4. A model combustor supplied with propane is also briefly shown as an example of application to a more realistic configuration.

Leading-edge receptivity of a hypersonic boundary layer on a flat plate

2001 ◽  
Vol 426 ◽  
pp. 73-94 ◽  
Author(s):  
A. A. MASLOV ◽  
A. N. SHIPLYUK ◽  
A. A. SIDORENKO ◽  
D. ARNAL
Keyword(s):  
Boundary Layer ◽  
Acoustic Waves ◽  
Free Stream ◽  
Three Dimensional ◽  
Leading Edge ◽  
Experimental Investigations ◽  
Two Dimensional ◽  
Inclination Angles ◽  
Tollmien Schlichting ◽  
Radiation Conditions

Experimental investigations of the boundary layer receptivity, on the sharp leading edge of a at plate, to acoustic waves induced by two-dimensional and three- dimensional perturbers, have been performed for a free-stream Mach number M∞ = 5.92. The fields of controlled free-stream disturbances were studied. It was shown that two-dimensional and three-dimensional perturbers radiate acoustic waves and that these perturbers present a set of harmonic motionless sources and moving sources with constant amplitude. The disturbances excited in the boundary layer were measured. It was found that acoustic waves impinging on the leading edge generate Tollmien–Schlichting waves in the boundary layer. The receptivity coefficients were obtained for several radiation conditions and intensities. It was shown that there is a dependence of receptivity coefficients on the wave inclination angles.

Numerical Flow Analysis in a Subsonic Vaned Radial Diffuser With Leading Edge Redesign

1999 ◽  
Vol 121 (1) ◽  
pp. 119-126 ◽  
Author(s):  
E. Casartelli ◽  
A. P. Saxer ◽  
G. Gyarmathy
Keyword(s):  
Static Pressure ◽  
Flow Analysis ◽  
Three Dimensional ◽  
Pressure Rise ◽  
Leading Edge ◽  
Inverse Design ◽  
Navier Stokes ◽  
Two Dimensional ◽  
Characteristic Lines ◽  
Design Software

The flow field in a subsonic vaned radial diffuser of a single-stage centrifugal compressor is numerically investigated using a three-dimensional Navier–Stokes solver (TASCflow) and a two-dimensional analysis and inverse-design software package (MISES). The vane geometry is modified in the leading edge area (two-dimensional blade shaping) using MISES, without changing the diffuser throughflow characteristics. An analysis of the two-dimensional and three-dimensional effects of two redesigns on the flow in each of the diffuser subcomponents is performed in terms of static pressure recovery, total pressure loss production, and secondary flow reduction. The computed characteristic lines are compared with measurements, which confirm the improvement obtained by the leading edge redesign in terms of increased pressure rise and operating range.

Sign in / Sign up

Export Citation Format

Share Document