Fuel Nozzle Performance Analysis Using Laser Techniques and Combustion Chamber With Optical Access

2006 ◽  
Author(s):  
G. R. Pucher ◽  
P. R. Underhill ◽  
W. D. Allan ◽  
G. Wang ◽  
S. Guy
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Scattered Light ◽  
Laser Sheet ◽  
Video Camera ◽  
Operating Conditions ◽  
Cross Sectional ◽  
Efficient Operation ◽  
Spray Pattern ◽  
Optical Access

Correct functioning of fuel nozzles is paramount to the efficient operation of gas turbine engines. Nozzles exhibiting poor distribution of droplets can be detrimental to combustion and overall engine life due to the creation of hot spots and potential for torching. The traditional technique of assessing nozzle performance involves operation in stagnant air conditions. Fuel spray is collected in the subdivided bins of a mechanical patternation system to determine spray symmetry. Recent improvements in spray analysis involve the use of laser light sheets to illuminate specific ‘slices’ of sprays in either cross sectional or axial planes. Typically, scattered light from the intersection of a laser sheet and a spray is recorded by a digital video camera, and images are averaged and corrected to determine the quality of the spray pattern. Such optical means of assessing spray quality provide great improvement over conventional means in terms of speed, convenience, and information retrieved. Nonetheless, data obtained in stagnant air conditions do not give an indication of spray geometry within combustion chambers under realistic operating conditions of airflow and combustion. This paper describes a project which applied laser-based optical patternation in a T-56 gas turbine combustion chamber rig with optical access under realistic flow conditions. As such, nozzle spray pattern was observed for various air and fuel flows in both cross sectional and plume (chamber axial) orientations. A deliberately damaged nozzle was also assessed for comparison with a good nozzle. Using optical filtration, spray patterns were observed under operationally representative combustion conditions.

Investigation of Flame Stabilization in a High-Pressure Multi-Jet Combustor by Laser Measurement Techniques

2014 ◽  
Author(s):  
Oliver Lammel ◽  
Tim Rödiger ◽  
Michael Stöhr ◽  
Holger Ax ◽  
Peter Kutne ◽  
...  
Keyword(s):  
High Pressure ◽  
Natural Gas ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Recirculation Zone ◽  
Flame Stabilization ◽  
Operating Conditions ◽  
Pollutant Emissions ◽  
Single Shot ◽  
Optical Access

In this contribution, comprehensive optical and laser based measurements in a generic multi-jet combustor at gas turbine relevant conditions are presented. The flame position and shape, flow field, temperatures and species concentrations of turbulent premixed natural gas and hydrogen flames were investigated in a high-pressure test rig with optical access. The needs of modern highly efficient gas turbine combustion systems, i.e., fuel flexibility, load flexibility with increased part load capability, and high turbine inlet temperatures, have to be addressed by novel or improved burner concepts. One promising design is the enhanced FLOX® burner, which can achieve low pollutant emissions in a very wide range of operating conditions. In principle, this kind of gas turbine combustor consists of several nozzles without swirl, which discharge axial high momentum jets through orifices arranged on a circle. The geometry provides a pronounced inner recirculation zone in the combustion chamber. Flame stabilization takes place in a shear layer around the jet flow, where fresh gas is mixed with hot exhaust gas. Flashback resistance is obtained through the absence of low velocity zones, which favors this concept for multi-fuel applications, e.g. fuels with medium to high hydrogen content. The understanding of flame stabilization mechanisms of jet flames for different fuels is the key to identify and control the main parameters in the design process of combustors based on an enhanced FLOX® burner concept. Both experimental analysis and numerical simulations can contribute and complement each other in this task. They need a detailed and relevant data base, with well-known boundary conditions. For this purpose, a high-pressure burner assembly was designed with a generic 3-nozzle combustor in a rectangular combustion chamber with optical access. The nozzles are linearly arranged in z direction to allow for jet-jet interaction of the middle jet. This line is off-centered in y direction to develop a distinct recirculation zone. This arrangement approximates a sector of a full FLOX® gas turbine burner. The experiments were conducted at a pressure of 8 bar with preheated and premixed natural gas/air and hydrogen/air flows and jet velocities of 120 m/s. For the visualization of the flame, OH* chemiluminescence imaging was performed. 1D laser Raman scattering was applied and evaluated on an average and single shot basis in order to simultaneously and quantitatively determine the major species concentrations, the mixture fraction and the temperature. Flow velocities were measured using particle image velocimetry at different section planes through the combustion chamber.

Experimental Investigations of Pressure Drop in the Combustion Chamber of Gas Turbine

1989 ◽  
Author(s):  
Marek Dzida ◽  
Krzysztof Kosowski
Keyword(s):  
Pressure Drop ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Experimental Results ◽  
Experimental Investigations ◽  
Relative Pressure ◽  
Wide Range ◽  
Few Data

In bibliography we can find many methods of determining pressure drop in the combustion chambers of gas turbines, but there is only very few data of experimental results. This article presents the experimental investigations of pressure drop in the combustion chamber over a wide range of part-load performances (from minimal power up to take-off power). Our research was carried out on an aircraft gas turbine of small output. The experimental results have proved that relative pressure drop changes with respect to fuel flow over the whole range of operating conditions. The results were then compared with theoretical methods.

Acoustic Resonances of an Industrial Gas Turbine Combustion System

2000 ◽  
Author(s):  
S. Hubbard ◽  
A. P. Dowling
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Acoustic Waves ◽  
Low Frequency ◽  
Operating Conditions ◽  
Combustion System ◽  
Resonant Frequencies ◽  
Bulk Mode ◽  
Acoustic Resonances ◽  
Industrial Gas Turbine

A theory is developed to describe low frequency acoustic waves in the complicated diffuser/combustor geometry of a typical industrial gas turbine. This is applied to the RB211-DLE geometry to give predictions for the frequencies of the acoustic resonances at a range of operating conditions. The main resonant frequencies are to be found around 605 Hz (associated with the plenum) and around 461 Hz and 823 Hz (associated with the combustion chamber), as well as one at around 22 Hz (a bulk mode associated with the system as a whole).

An Investigation of Turbine Erosion by Combustor Generated Carbon in a Light Weight Marine Gas Turbine

1978 ◽  
Author(s):  
R. J. Russell ◽  
J. J. Witton
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Fuel Type ◽  
Test Rig ◽  
Erosion Process ◽  
Marine Application ◽  
Mineral Dusts

A study has been made of the turbine erosion problem encountered in a marinized aero gas turbine which arose from the change of fuel type necessitated by the marine application. The work has involved the development of a technique for collecting carbon shed from the combustion chamber under engine operating conditions. Tests using the collector were made with a single combustor test rig and compared to engine experience. Combustion chamber modifications were developed having low solids emissions and their emissions characterized using the collector. The data from the collector show that smaller particles than hitherto collected can produce significant long-term erosion and that reduction on both size and quantity of particles is necessary to reduce erosion to acceptable levels. The data obtained in this study are compared with other published information on the basic erosion process and erosion in gas turbines by natural mineral dusts. The implications of the results to current and future engines are discussed.

Combination of 1D Code and CFD for Performance Analysis of a Silo Type Gas Turbine Combustor

2010 ◽  
Author(s):  
N. Rasooli ◽  
S. Besharat Shafiei ◽  
H. Khaledi
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Mass Distribution ◽  
Gas Turbines ◽  
Pressure Loss ◽  
Combustion Efficiency ◽  
Operating Conditions ◽  
Empirical Correlations ◽  
Combustion Chambers ◽  
Cfd Simulations

Whereas Gas Turbines are the most important producers of Propulsion and Power in the world and with attention to the importance of combustion chamber as one of the three basic components of Gas Turbine, various activities in different levels have been done on this component. Because of the environmental limitations and laws related to the pollutants such as NOx and CO, Lean Premixed Combustion Chambers are specially considered in gas turbine industries. This study is part of a Multi-Layer simulation of the whole gas turbine cycle in MPG Company. In this work, the combination of a general 1D code and CFD is used for deriving appropriate performance curves for a 1D and 0D gas turbine design, off-design and dynamic cycle code. This 1D code is a general code which has been developed for different combustion chambers; annular, can-annular, can type and silo type combustion chambers. The purpose of generating this 1D code is the possibility of fast analysis of combustors in different operating conditions and reaching required outputs. This 1D code is a part of a general simulation 1D code for gas turbine and was used for a silo type combustor performance prediction. This code generates required quantities such as pressure loss, exit temperature, liner temperature and mass distribution through the combustion chamber. Mass distribution and pressure loss are analyzed and determined with an electrical analogy. Results derived from 1D code are validated with empirical data available for different combustors. There is appropriate agreement between these experimental and analytical results. Drag coefficients for liner holes are available from experimental data and for burner are calculated as a curve with CFD simulations. What differs this code from other 1D codes for gas turbine combustors is the advantage of using combustion efficiencies evolved from numerical simulation results in different loads. These efficiencies are determined with CFD simulations and are available as maps and inserted into the gas temperature calculation algorithm of 1D code. In other 1D codes in this field, empirical correlations are used for combustion efficiency determination. Combustion efficiency curves for design and off-design conditions in this study are achieved by 2D and 3D simulation of combustion chamber with application of EBU/Finite Rate model and 8 step reactions of CH4 burning. Diffusion flame in low loads and premixed flame in high loads are considered. Flame stability and Lean Blow Out charts are evolved from CFD simulation and Heat transfer is applied with empirical correlations.

Modelling of the Combustion Process of a Premixed DLE Gas Turbine

2000 ◽  
Author(s):  
R. L. G. M. Eggels
Keyword(s):  
Reaction Mechanism ◽  
Flow Field ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Reaction Mechanisms ◽  
Gas Turbines ◽  
Combustion Process ◽  
Operating Conditions ◽  
Dimensional Manifold ◽  
Global Reaction

To obtain a better understanding of the internal combustion processes of gas turbines, CFD computations of a combustion chamber, based on a Rolls-Royce industrial gas turbine, were performed. Minor simplifications are made to generate a 3-D rotational symmetric geometry. Computations are performed at typical gas turbine conditions and natural gas is used as the fuel. An internal Rolls-Royce CFD code is applied to perform the computations. This paper explains the models used for the CFD computations and describes the advantages and limitations on the applied models. The combustion process has been modelled using a two-step global reaction mechanism and Intrinsic Low Dimensional Manifold (ILDM) reduced reaction mechanisms. The global reaction mechanisms are optimised for the considered operating conditions by modification of the reaction rates so that the same burning velocity and the amplitude CO-peak are obtained as predicted by detailed reaction mechanism (GRI 2.11, Bowman 1995). This optimisation is done considering a one-dimensional laminar flame. Although the global reaction mechanism is optimised for one particular operating condition, it appears that it is suitable for use over the entire range of operating conditions. The ILDM reduced reaction mechanisms are derived from GRI 2.11. Two ILDM tables are used to model two operating conditions, as they are specific for the pressure and inlet temperature. The interaction between turbulence and chemistry is modelled using presumed Probability Density Functions (PDF). The flow field in the combustion chamber is studied at isothermal and combusting conditions. It appeared that the flow field for burning and non-burning circumstances is quite different. There is a lack of experimental data so that it is not possible to verify the CFD results in detail. However, there is knowledge about the mechanisms by which the flame is stabilised and emissions are measured in the exhaust. The predicted flame front position agrees with that which is experimentally observed. The predicted increase of CO at low power is at the same order of magnitude as the measured emissions.

scholarly journals A Gas Path Fault Contribution Matrix for Marine Gas Turbine Diagnosis Based on a Multiple Model Fault Detection and Isolation Approach

Energies ◽  
2018 ◽  
Vol 11 (12) ◽  
pp. 3316 ◽  
Author(s):  
Qingcai Yang ◽  
Shuying Li ◽  
Yunpeng Cao ◽  
Fengshou Gu ◽  
Ann Smith
Keyword(s):  
Fault Detection ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Fault Detection And Isolation ◽  
Multiple Model ◽  
Efficient Operation ◽  
Model Sets ◽  
Wide Range ◽  
Model Set

To ensure reliable and efficient operation of gas turbines, multiple model (MM) approaches have been extensively studied for online fault detection and isolation (FDI). However, current MM-FDI approaches are difficult to directly apply to gas path FDI, which is one of the common faults in gas turbines and is understood to mainly be due to the high complexity and computation in updating hypothetical gas path faults for online applications. In this paper, a fault contribution matrix (FCM) based MM-FDI approach is proposed to implement gas path FDI over a wide operating range. As the FCM is realized via an additive term of the healthy model set, the hypothetical models for various gas path faults can be easily established and updated online. In addition, a gap metric analysis method for operating points selection is also proposed, which yields the healthy model set from the equal intervals linearized models to approximate the nonlinearity of the gas turbine over a wide range of operating conditions with specified accuracy and computational efficiency. Simulation case studies conducted on a two-shaft marine gas turbine demonstrated the proposed approach is capable of adaptively updating hypothetical model sets to accurately differentiate both single and multiple faults of various gas path faults.

Effects of Periodic Inflow Unsteadiness on the Time-Averaged Velocity Field and Pressure Recovery of a Diffusing Bend With Strong Curvature

2004 ◽  
Vol 126 (2) ◽  
pp. 229-237 ◽  
Author(s):  
M. I. Yaras ◽  
P. Orsi
Keyword(s):  
Velocity Field ◽  
Gas Turbine ◽  
Large Scale ◽  
Cross Flow ◽  
Operating Conditions ◽  
Pressure Recovery ◽  
Turbine Engines ◽  
Gas Turbine Engines ◽  
Cross Sectional ◽  
Data Set

This study examines the effects of periodic inflow unsteadiness on the flow development through fishtail-shaped diffusers utilized on small gas-turbine engines. In this application, periodic unsteadiness is caused by a jet-wake type of flow discharging from each passage of the centrifugal compressor impeller. The study consists of detailed measurements in a large-scale fishtail diffuser rig with a geometry that is typical of those used in small gas-turbine engines. Measurements of the transient velocity field have been performed at five cross-sectional planes throughout the diffuser using a miniature hot-wire probe with four wires. These measurements involve frequencies of inflow unsteadiness corresponding to design as well as off-design operating conditions. Results indicate significant effects of inflow unsteadiness at the low end of the tested frequencies on the time-averaged streamwise and cross-flow velocity fields in the diffuser. This is shown to translate into a notable impact on the pressure recovery. In addition to providing insight into the physics of this flow, the experimental results presented here constitute a detailed and accurate data set that can be used to validate computational-fluid-dynamics algorithms for this type of flow.

scholarly journals LES Analysis of CO Emissions from a High Pressure Siemens Gas Turbine Prototype Combustor at Part Load

Energies ◽  
2020 ◽  
Vol 13 (21) ◽  
pp. 5751
Author(s):  
Pascal Gruhlke ◽  
Christian Beck ◽  
Bertram Janus ◽  
Andreas M. Kempf
Keyword(s):  
Carbon Monoxide ◽  
High Pressure ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Operating Conditions ◽  
Part Load ◽  
Tracer Particles ◽  
Flame Quenching ◽  
Operating Points ◽  
Co Concentrations

This work contributes to the understanding of mechanisms that lead to increased carbon monoxide (CO) concentrations in gas turbine combustion systems. Large-eddy simulations (LES) of a full scale high pressure prototype Siemens gas turbine combustor at three staged part load operating conditions are presented, demonstrating the ability to predict carbon monoxide pollutants from a complex technical system by investigating sources of incomplete CO oxidation. Analytically reduced chemistry is applied for the accurate pollutant prediction together with the dynamic thickened flame model. LES results show that carbon monoxide emissions at the probe location are predicted in good agreement with the available test data, indicating two operating points with moderate pollutant levels and one operating point with CO concentrations below 10 ppm. Large mixture inhomogeneities are identified in the combustion chamber for all operating points. The investigation of mixture formation indicates that fuel-rich mixtures mainly emerge from the pilot stage resulting in high equivalence ratio streaks that lead to large CO levels at the combustor outlet. Flame quenching due to flame-wall-interaction are found to be of no relevance for CO in the investigated combustion chamber. Post-processing with Lagrangian tracer particles shows that cold air—from effusion cooling or stages that are not being supplied with fuel—lead to significant flame quenching, as mixtures are shifted to leaner equivalence ratios and the oxidation of CO is inhibited.

Performance Simulation of a Combined Cycle Power Generation System With Steam Injection in the Gas Turbine Combustion Chamber

2007 ◽  
Author(s):  
B. Law ◽  
B. V. Reddy
Keyword(s):  
Combustion Chamber ◽  
Gas Turbine ◽  
Thermal Efficiency ◽  
Pressure Ratio ◽  
Steam Injection ◽  
Combined Cycle ◽  
Operating Conditions ◽  
Inlet Temperature ◽  
Work Output ◽  
Gas Turbine Combustion

In the present work the effect of steam injection in the gas turbine combustion chamber is investigated on gas turbine and steam turbine work output and on thermal efficiency of the combined cycle power plant. The operating conditions investigated include gas turbine pressure ratio and gas turbine inlet temperature. The steam injection decreases the steam cycle output and boosts the gas cycle output and the net combined cycle work output and thermal efficiency significantly.

Sign in / Sign up

Export Citation Format

Share Document