Assessment of RQL Trapped Vortex Combustor for Stationary Gas Turbines

2003 ◽  
Author(s):  
Douglas L. Straub ◽  
Kent H. Casleton ◽  
Robie E. Lewis ◽  
Todd G. Sidwell ◽  
Daniel J. Maloney ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Operating Conditions ◽  
Experimental Results ◽  
Reactor Model ◽  
Lean Burn ◽  
Wide Range ◽  
The Rich ◽  
Detailed Kinetics ◽  
Trapped Vortex ◽  
Simple Network

This paper describes the evaluation of an alternative combustion approach to achieve low emissions for a wide range of fuel-types. This approach combines the potential advantages of a staged Rich-burn, Quick-mix, Lean-burn (RQL) combustor with the revolutionary Trapped Vortex Combustor (TVC) concept. Although RQL combustors have been proposed for low-BTU fuels, this paper considers the application of an RQL combustor for high-BTU natural gas applications. This paper will describe the RQL/TVC concept and experimental results conducted at 10 atmospheres (1013 kPa or 147 psia) and an inlet-air temperature of 644K (700°F). The results from a simple network reactor model using detailed kinetics are compared to the experimental observations. Neglecting mixing limitations, the simplified model suggests that NOx and CO performance below 10 parts-per-million could be achieved in an RQL approach. The CO levels predicted by the model are reasonably close to the experimental results over a wide range of operating conditions. The predicted NOx levels are reasonably close for some operating conditions, however, as the rich-stage equivalence ratio increases, the discrepancy between the experiment and the model increases. Mixing limitations are critical in any RQL combustor, and the mixing limitations for this RQL/TVC design are discussed.

Assessment of Rich-Burn, Quick-Mix, Lean-Burn Trapped Vortex Combustor for Stationary Gas Turbines

2005 ◽  
Vol 127 (1) ◽  
pp. 36-41 ◽  
Author(s):  
Douglas L. Straub ◽  
Kent H. Casleton ◽  
Robie E. Lewis ◽  
Todd G. Sidwell ◽  
Daniel J. Maloney ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Operating Conditions ◽  
Experimental Results ◽  
Reactor Model ◽  
Lean Burn ◽  
Wide Range ◽  
The Rich ◽  
Detailed Kinetics ◽  
Trapped Vortex ◽  
Simple Network

This paper describes the evaluation of an alternative combustion approach to achieve low emissions for a wide range of fuel types. This approach combines the potential advantages of a staged rich-burn, quick-mix, lean-burn (RQL) combustor with the revolutionary trapped vortex combustor (TVC) concept. Although RQL combustors have been proposed for low-Btu fuels, this paper considers the application of an RQL combustor for high-Btu natural gas applications. This paper will describe the RQL/TVC concept and experimental results conducted at 10 atm (1013 kPa or 147 psia) and an inlet-air temperature of 644 K (700°F). The results from a simple network reactor model using detailed kinetics are compared to the experimental observations. Neglecting mixing limitations, the simplified model suggests that NOx and CO performance below 10 parts per million could be achieved in an RQL approach. The CO levels predicted by the model are reasonably close to the experimental results over a wide range of operating conditions. The predicted NOx levels are reasonably close for some operating conditions; however, as the rich-stage equivalence ratio increases, the discrepancy between the experiment and the model increases. Mixing limitations are critical in any RQL combustor, and the mixing limitations for this RQL/TVC design are discussed.

Experimental Investigations of Pressure Drop in the Combustion Chamber of Gas Turbine

1989 ◽  
Author(s):  
Marek Dzida ◽  
Krzysztof Kosowski
Keyword(s):  
Pressure Drop ◽  
Combustion Chamber ◽  
Gas Turbine ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Experimental Results ◽  
Experimental Investigations ◽  
Relative Pressure ◽  
Wide Range ◽  
Few Data

In bibliography we can find many methods of determining pressure drop in the combustion chambers of gas turbines, but there is only very few data of experimental results. This article presents the experimental investigations of pressure drop in the combustion chamber over a wide range of part-load performances (from minimal power up to take-off power). Our research was carried out on an aircraft gas turbine of small output. The experimental results have proved that relative pressure drop changes with respect to fuel flow over the whole range of operating conditions. The results were then compared with theoretical methods.

Trapped Vortex Combustor Performance for Heavy-Duty Gas Turbines

2008 ◽  
Author(s):  
Joel M. Haynes ◽  
Daniel Micka ◽  
Ben Hojnacki ◽  
Craig Russell ◽  
John Lipinski ◽  
...  
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Nox Reduction ◽  
Operating Conditions ◽  
Heavy Duty ◽  
Reactor Model ◽  
Emission Performance ◽  
Lean Premixed ◽  
Heavy Duty Gas Turbine ◽  
Trapped Vortex

The application of the trapped vortex combustor (TVC) concept to heavy-duty gas turbine conditions has been explored. Combustor stability, lean blow out, and emission performance requirements limit design options for conventional lean premixed combustors. The TVC concept has demonstrated reduced emissions and high turndown with liquid fuels and could overcome existing lean premixed performance constraints as well. The present study examines premixed injection of natural gas into the TVC at heavy-duty gas turbine conditions. The emission performance is measured over a range of operating conditions. The combustor turndown and dynamics performance are also presented. To forecast the performance potential of the TVC combustor a chemical reactor network model was developed. The model was anchored with experimental data and implemented in the prediction of TVC combustor emissions and turndown performance. The reactor model confirms that NOx reduction greater than 60% is possible using a trapped vortex combustor (TVC).

Uncertainty Analysis of Inflow Conditions on an HPT Gas Turbine Nozzle: Effect on Particle Deposition

2020 ◽  
Author(s):  
R. Friso ◽  
N. Casari ◽  
M. Pinelli ◽  
A. Suman ◽  
F. Montomoli
Keyword(s):  
Gas Turbine ◽  
Energy Efficient ◽  
Gas Turbines ◽  
Particle Deposition ◽  
Operating Conditions ◽  
Wide Range ◽  
And Performance ◽  
Gas Turbine Nozzle ◽  
The Impact ◽  
Inflow Conditions

Abstract Gas turbines (GT) are often forced to operate in harsh environmental conditions. Therefore, the presence of particles in their flow-path is expected. With this regard, deposition is a problem that severely affects gas turbine operation. Components’ lifetime and performance can dramatically vary as a consequence of this phenomenon. Unfortunately, the operating conditions of the machine can vary in a wide range, and they cannot be treated as deterministic. Their stochastic variations greatly affect the forecasting of life and performance of the components. In this work, the main parameters considered affected by the uncertainty are the circumferential hot core location and the turbulence level at the inlet of the domain. A stochastic analysis is used to predict the degradation of a high-pressure-turbine (HPT) nozzle due to particulate ingestion. The GT’s component analyzed as a reference is the HPT nozzle of the Energy-Efficient Engine (E3). The uncertainty quantification technique used is the probabilistic collocation method (PCM). This work shows the impact of the operating conditions uncertainties on the performance and lifetime reduction due to deposition. Sobol indices are used to identify the most important parameter and its contribution to life. The present analysis enables to build confidence intervals on the deposit profile and on the residual creep-life of the vane.

Development of a Constitutive Backstress Model for the Prediction of Creep and Stress Relaxation in Gas Turbine Materials

2020 ◽  
Author(s):  
Andrew Moffat ◽  
Richard Green ◽  
Calum Ferguson ◽  
Brent Scaletta
Keyword(s):  
Stress Relaxation ◽  
Creep Deformation ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Creep Model ◽  
Effect Of Temperature ◽  
Deformation Model ◽  
Corrosion Resistant ◽  
Single Temperature ◽  
Wide Range

Abstract There is a drive towards a broader range of fuels in industrial gas turbines, with higher levels of sulphur and potentially hydrogen. Due to these harsher environments, there is also a drive for corrosion resistant alloys and coatings. A number of key corrosion resistant superalloys, which are being employed to cope with these evolving conditions, exhibit primary creep. It is therefore imperative that fundamental material models, such as those for creep deformation, are developed to ensure they can accurately predict the material response to evolving operating conditions. The requirements for a creep model are complex. The model must be able to: predict forward creep deformation in regions dominated by primary loads (such as pressure); predict stress relaxation in regions dominated by secondary loads (such as differential thermal expansion); predict the effects of different creep hardening mechanisms. It is also clear that there is an interaction between fatigue and creep. With flexible operation, this interaction can be significant and should be catered for in lifing methods. A model that has the potential to account for the effect of plasticity on creep, and creep on plasticity is therefore desirable. In previous work the authors presented the concept for a backstress model to predict creep strain rates in superalloys. This model was fitted to a limited dataset at a single temperature. The approach was validated using simple creep-dwell tests at the same temperature. This paper expands on the previous work in several ways: 1) The creep model has been fitted over a wide range of temperatures. Including the effect of temperature in complex creep models presents a number of difficulties in model fitting and these are explored. 2) The model was fitted to constant load (forward creep) and constant strain (stress relaxation) tests since any creep model should be able to predict both forms of creep deformation. However, these are often considered separately due to the difficulty of fitting models to two different datasets. 3) The creep deformation model was validated on stress change tests to ensure the creep deformation response can cope with changes in response variables. 4) The approach was validated using creep-fatigue tests to show that the creep deformation model, in addition to our established fatigue models, can predict damage in materials under complex loading.

A State-of-the-Art CFD Setup for Axial Compressors: Details and Validation

2020 ◽  
Author(s):  
Lorenzo Cozzi ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Savino Depalo ◽  
Pio Astrua ◽  
...  
Keyword(s):  
Gas Turbines ◽  
Power Plants ◽  
State Of The Art ◽  
Secondary Flows ◽  
Operating Conditions ◽  
Tip Clearance ◽  
Cfd Modelling ◽  
Axial Compressors ◽  
Surge Margin ◽  
Wide Range

Abstract The overall fraction of the power produced by renewable sources in the energy market has significantly increased in recent years. The power output of most of these clean sources is intrinsically variable. At present day and most likely in the upcoming future, due to the lack of inexpensive and reliable large energy storage systems, conventional power plants burning fossil fuels will still be part of the energy horizon. In particular, power generators able to promptly support the grid stability, such as gas turbines, will retain a strategic role. This new energy scenario is pushing gas turbine producers to improve the flexibility of their turbomachines, increasing the need for reliable numerical tools adopted to design and validate the new products also in operating conditions far from the nominal one. Especially when dealing with axial compressors, i.e. machines experiencing intense adverse pressure gradients, complex flow structures and severe secondary flows, CFD modelling of offdesign operation can be a real challenge. In this work, a state-of-the art CFD framework for RANS analysis of axial compressors is presented. The various aspects involved in the whole setup are discussed, including boundary conditions, meshing strategies, mixing planes modelling, tip clearance treatment, shroud leakages and turbulence modelling. Some experiences about the choice of these aspects are provided, derived from a long-date practice on this kind of turbomachines. Numerical results are reported for different full-scale compressors of the Ansaldo Energia fleet, covering a wide range of operating conditions. Furthermore, details about the capability of the setup to predict compressor performance and surge-margin have been added to the work. In particular, the setup surge-margin prediction has been evaluated in an operating condition in which the turbomachine experiences experimental stall. Finally, thanks to several on-field data available at different corrected speeds for operating conditions ranging from minimum to full load, a comprehensive validation of the presented numerical framework is also included in the paper.

Experimental and Computational Analysis of Additive Manufactured Augmented Backside Liner Cooling Surfaces for Use in Micro Gas Turbines

2020 ◽  
Author(s):  
Adamos Adamou ◽  
Colin Copeland
Keyword(s):  
Heat Transfer ◽  
Film Cooling ◽  
Gas Turbines ◽  
Conjugate Heat Transfer ◽  
Reverse Flow ◽  
Operating Conditions ◽  
Experimental Results ◽  
Gas Temperature ◽  
Cfd Models ◽  
High Heat Transfer

Abstract Augmented backside cooling refers to the enhancement of the backside convection of a combustor liner using extended heat transfer surfaces to fully utilise the cooling air by maximising the heat transfer to pumping ratio characteristic. Although film cooling has and still is widely used in the gas turbine industry, augmented backside cooling has been in development for decades now. The reason for this, is to reduce the amount of air used for liner cooling and to also reduce the emissions caused by using film cooling in the primary zones. In the case of micro gas turbines, emissions are of even greater importance, since the regulations for such engines will most likely become stricter in the following years due to a global effort to reduce emission. Furthermore, the liners investigated in this paper are for a 10 kWe micro turbine, destine for various potential markets, such as combine heat and power for houses, EV hybrids and even small UAVs. The majority of these markets require long service intervals, which in turn requires the combustor liners to be under the least amount of thermal stress possible. The desire to also increase combustor inlet temperatures with the use of recuperated exhaust gases, which in turn increase the overall system efficiency, limits the cooling effectiveness of the inlet air. Due to all these reasons, an advanced form of augmented backside cooling would be of substantial significance in such a system. Currently some very simple designs are used in the form of straight plain fins, transverse strips or other similar geometries, but the creation of high heat transfer efficiency surfaces in such small sizes becomes very difficult with traditional subtractive manufacturing methods. When using additive manufacturing though these types of surfaces are not an issue. This paper covers the comparison of experimental results with conjugate heat transfer CFD models and empirical heat balance models for two different AM liner cooling geometries and an AM blank liner. The two cooling fin geometries include a rotating plain fin and an offset strip fin. The liners were tested in an AM built reverse flow radial swirl stabilised combustion chamber at a variety of operating conditions. During the experiments the surfaces were compared using a thermal camera to record the outer liner temperature which was viewed through a quartz outer casing. The experimental results showed that the cooling surfaces were effective at reducing the liner temperatures with minimal pressure losses for multiple operating points. Those results were then compared against the conjugate heat transfer CFD models and the empirical calculations used to design the surfaces initially. From this comparison, it was noticed both the CFD and empirical calculations under predicted the wall temperatures. This is thought to be due to inaccuracies in the predicted flame temperatures and the assumed emissivity values used to calibrate the thermal imaging camera. Further uncertainties arise from the assumption of a constant air and hot gas temperature and mass flow along the cooling surfaces and the lack of data for the surface roughness of the parts.

Experimental and Numerical Study for Improved Understanding of Mixed-Convection Type of Flows in Turbine Casing Cavities During Shut-Down Regimes

2021 ◽  
Author(s):  
Oguzhan Murat ◽  
Budimir Rosic ◽  
Koichi Tanimoto ◽  
Ryo Egami
Keyword(s):  
Natural Convection ◽  
Flow Field ◽  
Mixed Convection ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Scale Model ◽  
Unsteady Temperature ◽  
Numerical Predictions ◽  
Wide Range ◽  
Turbine Casing

Abstract Due to increase in the power generation from renewable sources, steam and gas turbines will be required to adapt for more flexible operations with frequent start-ups and shut-downs to provide load levelling capacity. During shut-down regimes, mixed convection takes place with natural convection dominance depending on the operating conditions in turbine cavities. Buoyant flows inside the turbine that are responsible for non-uniform cooling leading to thermal stresses and compromise clearances directly limits the operational flexibility. Computational fluid dynamics (CFD) tools are required to predict the flow field during these regimes since direct measurements are extremely difficult to conduct due to the harsh operating conditions. Natural convection with the presence of cross-flow -mixed convection has not been extensively studied to provide detailed measurements. Since the literature lacks of research on such flows with real engine representative operating conditions for CFD validation, the confidence in numerical predictions is rather inadequate. This paper presents a novel experimental facility that has been designed and commissioned to perform very accurate unsteady temperature and flow field measurements in a simplified turbine casing geometry. The facility is capable of reproducing a wide range of Richardson, Grashof and Reynolds numbers which are representative of engine realistic operating conditions. In addition, high fidelity, wall resolved LES with dynamic Smagorinsky subgrid scale model has been performed. The flow field as well as heat transfer characteristics have been accurately captured with LES. Lastly, inadequacy of RANS for mixed type of flows has been highlighted.

Analysis of Part Electric Gas Turbine: A Novel Hybrid Propulsion Concept

2019 ◽  
Author(s):  
M. S. N. Murthy ◽  
Subhash Kumar ◽  
Sheshadri Sreedhara
Keyword(s):  
Gas Turbine ◽  
Electric Motor ◽  
Gas Turbines ◽  
Operating Conditions ◽  
Variable Speed ◽  
Hybrid Propulsion ◽  
Design Point ◽  
Part Load ◽  
Wide Range ◽  
Efficient Option

Abstract A gas turbine engine (GT) is very complex to design and manufacture considering the power density it offers. Development of a GT is also iterative, expensive and involves a long lead time. The components of a GT, viz compressor, combustor and turbine are strongly dependent on each other for the overall performance characteristics of the GT. The range of compressor operation is dependent on the functional and safe limits of surging and choking. The turbine operating speeds are required to be matched with that of compressor for wide range of operating conditions. Due to this constrain, design for optimum possible performance is often sacrificed. Further, once catered for a design point, gas turbines offer low part load efficiencies at conditions away from design point. As a more efficient option, a GT is practically achievable in a split configuration, where the compressor and turbine rotate on different shafts independently. The compressor is driven by a variable speed electric motor. The power developed in the combustor using the compressed air from the compressor and fuel, drives the turbine. The turbine provides mechanical shaft power through a gear box if required. A drive taken from the shaft rotates an electricity generator, which provides power for the compressor’s variable speed electric motor through a power bank. Despite introducing, two additional power conversions compared to a conventional GT, this split configuration named as ‘Part Electric Gas Turbine’, has a potential for new applications and to achieve overall better efficiencies from a GT considering the poor part load characteristics of a conventional GT.

Analysis of Gas Turbine Rotating Cavities by an One-Dimensional Model

2009 ◽  
Author(s):  
Riccardo Da Soghe ◽  
Bruno Facchini ◽  
Luca Innocenti ◽  
Mirko Micio
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Design Tool ◽  
Operating Conditions ◽  
Outer Flow ◽  
One Dimensional ◽  
Wide Range ◽  
Air System ◽  
Secondary Air ◽  
Radial Outflow

Reliable design of secondary air system is one of the main tasks for the safety, unfailing and performance of gas turbine engines. To meet the increasing demands of gas turbines design, improved tools in prediction of the secondary air system behavior over a wide range of operating conditions are needed. A real gas turbine secondary air system includes several components, therefore its analysis is not carried out through a complete CFD approach. Usually, that predictions are performed using codes, based on simplified approach which allows to evaluate the flow characteristics in each branch of the air system requiring very poor computational resources and few calculation time. Generally the available simplified commercial packages allow to correctly solve only some of the components of a real air system and often the elements with a more complex flow structure cannot be studied; among such elements, the analysis of rotating cavities is very hard. This paper deals with a design-tool developed at the University of Florence for the simulation of rotating cavities. This simplified in-house code solves the governing equations for steady one-dimensional axysimmetric flow using experimental correlations both to incorporate flow phenomena caused by multidimensional effects, like heat transfer and flow field losses, and to evaluate the circumferential component of velocity. Although this calculation approach does not enable a correct modeling of the turbulent flow within a wheel space cavity, the authors tried to create an accurate model taking into account the effects of inner and outer flow extraction, rotor and stator drag, leakages, injection momentum and, finally, the shroud/rim seal effects on cavity ingestion. The simplified calculation tool was designed to simulate the flow in a rotating cavity with radial outflow both with a Batchelor and/or Stewartson flow structures. A primary 1D-code testing campaign is available in the literature [1]. In the present paper the authors develop, using CFD tools, reliable correlations for both stator and rotor friction coefficients and provide a full 1D-code validation comparing, due to lack of experimental data, the in house design-code predictions with those evaluated by CFD.

Sign in / Sign up

Export Citation Format

Share Document