The Effect of the Source Location on the Acoustic Excitation on Laminar-Turbulent Transition on Swept Wing Boundary Layer

2002 ◽  
Author(s):  
B. Gu¨lac¸ti ◽  
S. Aubrun ◽  
A. Seraudie ◽  
D. Arnal
Keyword(s):  
Wind Tunnel ◽  
Test Section ◽  
Three Dimensional ◽  
Source Location ◽  
Sound Level ◽  
Acoustic Excitation ◽  
Hot Wire ◽  
Swept Wing ◽  
Turbulent Transition ◽  
Laminar Turbulent Transition

The effect of the source location and the direction of the propagation on the laminar-turbulent transition on swept-wing three-dimensional boundary layers are investigated experimentally. Also the crossflow case is handled in detail. The source for the acoustic excitation is placed in four different locations: in front of the wing, on top of the test section, behind the wing and in front of the wind tunnel. Three different experimental cases (streamwise, crossflow and mixed cases) are examined for each location with two different excitation bands. For the most efficient frequency ranges and the highest sound pressure levels an upstream shift of transition motion between 20%–35% of chord length for streamwise case and between 5%–10% for the crossflow case are observed. While in front of the wing and behind the wing are the most efficient loudspeaker positions in the streamwise case, in the crossflow case the most efficient locations are observed to be in front of the wing and on top of the test section. It is concluded that acoustic sound level plays a more important role in the upstream shift of the transition than the source location and placing the loudspeaker in front of the wind tunnel is not an efficient position. For the crossflow instabilities dominated transition the stationary vortices are clearly seen from the velocity contours obtained by the hot-wire. Secondary instabilities couldn’t be observed in the hot-wire spectra. The surface roughness of the wing that is reduced to 0.25µm does not change the transition location in the crossflow case.

scholarly journals Validation of a laminar-turbulent transition prediction technique for a swept-wing boundary-layer flow

2021 ◽  
Vol 2057 (1) ◽  
pp. 012081
Author(s):  
A V Boiko ◽  
V I Borodulin ◽  
A V Ivanov ◽  
S V Kirilovskiy ◽  
D A Mischenko ◽  
...  
Keyword(s):  
Boundary Layer ◽  
Wind Tunnel ◽  
Test Section ◽  
Wind Tunnel Test ◽  
Cross Flow ◽  
Infrared Camera ◽  
Main Flow ◽  
Swept Wing ◽  
Turbulent Transition ◽  
Laminar Turbulent Transition

Abstract The laminar-turbulent transition in the boundary layer of a 45° swept wing model installed at zero attack angle in the test section of a subsonic wind-tunnel was detected with the help of an infrared camera. The camera recorded sequences of frames, the evolution of the preheated model surface temperature acquired and used for differentiating between the laminar and turbulent regions. The transition onset was evaluated at both sides of the model. Corresponding main flow computations in the virtual wind tunnel test section were performed at the same flow conditions with ANSYS Fluent. The computed main-flow velocity profiles along inviscid streamlines were used for analysis of hydrodynamic stability of the boundary layer with respect to Tollmien-Schlichting waves and stationary cross-flow vortices to obtain N-factor distributions along the model chord. A comparison of the experimental and the computed transition onsets was performed.

An experimental study of the influence of riblets on transition

1996 ◽  
Vol 315 ◽  
pp. 31-49 ◽  
Author(s):  
G. R. Grek ◽  
V. V. Kozlov ◽  
S. V. Titarenko
Keyword(s):  
Experimental Study ◽  
Three Dimensional ◽  
Negative Influence ◽  
Positive Influence ◽  
Linear Stage ◽  
Turbulent Transition ◽  
Transition Structures ◽  
Stage Transition ◽  
Tollmien Schlichting ◽  
Laminar Turbulent Transition

An experimental study of the effect of riblets on three-dimensional nonlinear structures, the so-called Λ-vortices on laminar-turbulent transition showed that riblets delay the transformation of the Λ-vortices into turbulent spots and shift the point of transition downstream. This result is opposite to the negative influence of such ribbed surfaces on two-dimensional linear Tollmien-Schlichting waves (the linear stage of transition). Thus, the ribbed surface influences laminar-turbulent transition structures differently: a negative influence on the linear-stage transition structures and a positive influence on the nonlinear-stage transition structures. It is demonstrated that transition control by means of riblets requires special attention to be paid to the choice of their location, taking into account the stage of transition.

Homogeneous, Isotropic Flow in Grid Generated Turbulence

1999 ◽  
Vol 122 (1) ◽  
pp. 51-56 ◽  
Author(s):  
Riccardo Tresso ◽  
David R. Munoz
Keyword(s):  
Wind Tunnel ◽  
Three Dimensional ◽  
Wind Tunnel Test ◽  
Flow Region ◽  
Hot Wire ◽  
Spatial Homogeneity ◽  
One Dimensional ◽  
Streamwise Location ◽  
Dimensional Measurements ◽  
Approach Zero

Detailed grid generated turbulent analysis has been completed using a three-dimensional hot-wire anemometer and traversing mechanism to identify a homogeneous, isotropic flow region downstream of a square mesh. The three-dimensional fluctuating velocity measurements were recorded along the centerline of a wind tunnel test section and spatially over the entire wind tunnel cross section downstream of the square mesh. Turbulent intensities for various grid sizes and Reynolds numbers ranged from a minimum of 0.2 percent to a maximum of 2.2 percent in each of the three principal velocity directions. Spatial homogeneity and isotropy were determined for several turbulent flow conditions and downstream positions using the method of covariances. Covariances, in theory, should approach zero asymptotically; however, in practice, this was not achievable. A subjective judgment is required to determine downstream location where the variance of the three covariances reaches a value close to zero. The average standard deviation provides an estimate for defining the limit or subjective threshold needed to determine the onset of homogeneous, isotropic flow. Implementing this threshold, a quantitative method was developed for predicting the streamwise location for the onset of the homogeneous, isotropic flow region downstream of a 25.4 mm square grid as a function of Reynolds number. A comparison of skewness, determined from one-dimensional hot wire anemometer measurements, and covariances, determined from three dimensional hot wire anemometer measurements, indicates a need for caution when relying solely on one-dimensional measurements for determination of turbulence isotropy. The comprehensive three-dimensional characterization also provides an improved understanding of spatial distribution of fundamental turbulence quantities generated by the grid within a low-speed wind tunnel. [S0098-2202(00)02501-3]

On the Effects of Turbulence Modeling on the Fluid-Structure Interaction of a Rigid Cylinder

2016 ◽  
Author(s):  
Guilherme Feitosa Rosetti ◽  
Guilherme Vaz ◽  
André Luís Condino Fujarra
Keyword(s):  
Turbulence Modeling ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Reynolds Numbers ◽  
Boundary Layer Separation ◽  
Turbulent Transition ◽  
Moving Cylinder ◽  
Wide Range ◽  
Cylinder Flow ◽  
Laminar Turbulent Transition

The cylinder flow is a canonical problem for Computational Fluid Dynamics (CFD), as it can display several of the most relevant issues for a wide class of flows, such as boundary layer separation, vortex shedding, flow instabilities, laminar-turbulent transition and others. Several applications also display these features justifying the amount of energy invested in studying this problem in a wide range of Reynolds numbers. The Unsteady Reynolds Averaged Navier Stokes (URANS) equations combined with simplifying assumptions for turbulence have been shown inappropriate for the captive cylinder flow in an important range of Reynolds numbers. For that reason, recent improvements in turbulence modeling has been one of the most important lines of research within that issue, aiming at better prediction of flow and loads, mainly targeting the three-dimensional effects and laminar-turbulent transition, which are so important for blunt bodies. In contrast, a much smaller amount of work is observed concerning the investigation of turbulent effects when the cylinder moves with driven or free motions. Evidently, larger understanding of the contribution of turbulence in those situations can lead to more precise mathematical and numerical modeling of the flow around a moving cylinder. In this paper, we present CFD calculations in a range of moderate Reynolds numbers with different turbulence models and considering a cylinder in captive condition, in driven and in free motions. The results corroborate an intuitive notion that the inertial effects indeed play very important role in determining loads and motions. The flow also seems to adapt to the motions in such a way that vortices are more correlated and less influenced by turbulence effects. Due to good comparison of the numerical and experimental results for the moving-cylinder cases, it is observed that the choice of turbulence model for driven and free motions calculations is markedly less decisive than for the captive cylinder case.

Coupling PSE and FLUENT to Predict Laminar-Turbulent Transition in Boundary Layers

2013 ◽  
Vol 432 ◽  
pp. 168-172
Author(s):  
Y. Zhou ◽  
Y.H. Fang
Keyword(s):  
Flat Plate ◽  
Boundary Layers ◽  
Three Dimensional ◽  
Basic Flow ◽  
Two Dimensional ◽  
S Wave ◽  
S Waves ◽  
Turbulent Transition ◽  
Transition Criterion ◽  
Laminar Turbulent Transition

In this paper, the coupling method of PSE and FLUENT was experimented for predicting the laminar-turbulent transition. The software FLUENT was used to get the basic flow over a flat plate. A two-dimensional T-S wave and a pair of three-dimensional T-S waves were fed in at the entrance. The transition criterion was verified by DNS results. The availability of the coupling methodology has been evaluated.

Sign in / Sign up

Export Citation Format

Share Document