Slot Jet Impinging a Curved Wall

2002 ◽  
Author(s):  
V. Gilard ◽  
L.-E. Brizzi
Keyword(s):  
Data Processing ◽  
Statistical Data ◽  
Velocity Fields ◽  
Pressure Measurements ◽  
Reynolds Stresses ◽  
Velocity Measurements ◽  
Mean Velocity ◽  
Concave Wall ◽  
Wall Flow ◽  
The Mean

In order to study the aerodynamics of a slot jet impinging a concave wall, flow visualisations, velocity measurements by PIV and pressure measurements are carried out. A statistical data processing allows us to obtain the mean velocity fields and the Reynolds stresses. Among the studied parameters, the effect of the relative curvature of the wall is studied in particular because of a jet beating phenomenon observed for a low relative curvature. Three flow modes are then described.

Comparison Between a Slot Jet and Round Jets Impinging a Curved Wall

2003 ◽  
Author(s):  
V. Gilard ◽  
L.-E. Brizzi
Keyword(s):  
Data Processing ◽  
Flow Structure ◽  
Statistical Data ◽  
Velocity Fields ◽  
Reynolds Stresses ◽  
Velocity Measurements ◽  
Mean Velocity ◽  
Statistical Data Processing ◽  
Round Jets ◽  
The Mean

Velocity measurements by PIV are realized in order to compare a slot jet and round jets impinging a curved surface. A statistical data processing allows us to obtain the mean velocity fields and the Reynolds stresses. For the two jet geometries, the flow structure is described. Some velocity distributions according to different axis are extracted of the mean velocity fields and are also described.

Turbulent flow over large-amplitude wavy surfaces

1984 ◽  
Vol 140 ◽  
pp. 27-44 ◽  
Author(s):  
Jeffrey Buckles ◽  
Thomas J. Hanratty ◽  
Ronald J. Adrian
Keyword(s):  
Boundary Layer ◽  
Turbulent Flow ◽  
Velocity Fields ◽  
Laser Doppler Velocimeter ◽  
Free Shear Layer ◽  
Wave Surface ◽  
Velocity Measurements ◽  
Mean Velocity ◽  
Wavy Surfaces ◽  
The Mean

The laser-Doppler velocimeter is used to measure the mean and the fluctuating velocity for turbulent flow over a solid sinusoidal wave surface having a wavelength λ of 50.8 mm and a wave amplitude of 5.08 mm. For this flow, a large separated region exists, extending from x/λ = 0.14 to 0.69. From the mean velocity measurements, the time-averaged streamlines and therefore the extent of the separated region are calculated. Three flow elements are identified: the separated region, an attached boundary layer, and a free shear layer formed by the detachment of the boundary layer from the wave surface. The characteristics of these flow elements are discussed in terms of the properties of the mean and fluctuating velocity fields.

Slot Jet Impinging On A Concave Curved Wall

2005 ◽  
Vol 127 (3) ◽  
pp. 595-603 ◽  
Author(s):  
Virginie Gilard ◽  
Laurent-Emmanuel Brizzi
Keyword(s):  
Curvature Radius ◽  
Pressure Measurements ◽  
Reynolds Stresses ◽  
Mean Velocity ◽  
Concave Wall ◽  
Image Velocimetry ◽  
Mean Pressure ◽  
Jet Structure ◽  
First Time ◽  
Type Of Behavior

In order to study the aerodynamics of a slot jet impinging a concave wall, flow visualizations, velocity measurements by particle image velocimetry (PIV) (mean velocity fields and the Reynolds stresses) and mean pressure measurements were carried out. Among the studied parameters is the effect of the relative curvature of the wall, in particular the low curvature radius because of the presence of three semistable positions. It is the first time that this type of behavior is observed in fluid mechanics. Thus three flow modes are observed and their behaviors are described. These different behaviors modify considerably the impinging jet structure and the turbulence values. Finally, from the pressure measurements, we were able to determine a criterion that allows us to know the behavior of the jet.

Prediction of Confined Coaxial Turbulent Jet Mixing With a Streamwise Differencing Scheme

1991 ◽  
Author(s):  
M. A. R. Sharif ◽  
M. A. Gadalla
Keyword(s):  
Reynolds Stresses ◽  
Low Velocity ◽  
Mean Velocity ◽  
Jet Mixing ◽  
Air Jet ◽  
Air Stream ◽  
Constant Diameter ◽  
Flow Domain ◽  
The Mean ◽  
Secondary Air

Abstract Isothermal turbulent mixing of an axisymmetric primary air jet with a low velocity annular secondary air stream inside a constant diameter cylindrical enclosure is predicted. The flow domain from the inlet to the fully developed downstream locations is considered. The predicted flow field properties include the mean velocity and pressure and the Reynolds stresses. Different velocity and diameter ratios between the primary and the secondary jets have been investigated to characterize the flow in terms of these parameters. A bounded stream-wise differencing scheme is used to minimize numerical diffusion and oscillation errors. Predictions are compared with available experimental data to back up numerical findings.

Hot Wire Measurements at the Exit of a Centrifugal Compressor Impeller

1979 ◽  
Vol 193 (1) ◽  
pp. 341-347
Author(s):  
A. Goulas ◽  
R. C. Baker
Keyword(s):  
Centrifugal Compressor ◽  
Magnetic Tape ◽  
Reynolds Stresses ◽  
Hot Wire ◽  
Mean Velocity ◽  
Isentropic Flow ◽  
Compressor Impeller ◽  
The Mean

Hot wire measurements at the exit of a small centrifugal compressor impeller are reported. Three different hot wire readings were obtained and stored on a magnetic tape for each point by gating the analogue hot wire signal with a pulse which indicated circumferential position. The combination of the three readings yielded the mean velocity and some Reynolds stresses at each point. The measurements show a ‘jet-wake’ profile towards the shroud and ‘isentropic’ flow near the hub.

A wind tunnel simulation of the mean velocity fields behind upright porous fences

2007 ◽  
Vol 146 (1-2) ◽  
pp. 82-93 ◽  
Author(s):  
Zhibao Dong ◽  
Wanyin Luo ◽  
Guangqiang Qian ◽  
Hongtao Wang
Keyword(s):  
Wind Tunnel ◽  
Velocity Fields ◽  
Mean Velocity ◽  
Wind Tunnel Simulation ◽  
The Mean

PIV Investigation of an Open Channel Flow Over a Forward Facing Step

2007 ◽  
Author(s):  
M. K. Shah ◽  
M. F. Tachie
Keyword(s):  
Open Channel ◽  
Particle Image ◽  
Open Channel Flow ◽  
Reynolds Stresses ◽  
Velocity Measurements ◽  
Particle Image Velocimetry Technique ◽  
Mean Velocity ◽  
Freestream Velocity ◽  
Image Velocimetry ◽  
Forward Facing Step

The characteristics of an open channel turbulent flow over a forward facing step (FFS) are investigated in the present study. Two step heights, h = 6 and 9 mm, at Reynolds number, Reh, (based on the approach freestream velocity, U0, and step height, h) of 1900 and 2800 respectively were studied. Particle image velocimetry technique (PIV) was used to obtain detailed velocity measurements upstream of the FFS, in the reattachment region (x/h = 0, 1, 2) and in the redevelopment region (x/h = 4, 10, 15 and 50). The boundary layer integral parameters, mean velocity profiles and Reynolds stresses obtained in the reattachment and redevelopment region are used to document some of the salient features of the flow.

Time-Resolved Velocity Measurements in a Matched Refractive Index Facility of Randomly Packed Spheres

2018 ◽  
Author(s):  
Ethan Kappes ◽  
Mateusz Marciniak ◽  
Andrew Mills ◽  
Robert Muyshondt ◽  
Stephen King ◽  
...  
Keyword(s):  
Root Mean Square ◽  
Experimental Studies ◽  
Reynolds Numbers ◽  
Index Of Refraction ◽  
Mean Square ◽  
Reynolds Stresses ◽  
Velocity Measurements ◽  
Mean Velocity ◽  
Time Resolved ◽  
Wall Boundary

Complex geometries and randomly connected void spaces within packed beds have hindered efforts to characterize the underlying transport phenomena occurring within. In this communication, we present our experimental studies on a facility of randomly packed spheres that can be a representative of sections within a reactor core in a nuclear power plant. The results of high-fidelity velocity measurements can be seen using Time-Resolved Particle Image Velocimetry (TR-PIV) at the pore scales and near the wall boundary in the Matched Index of Refraction (MIR) facility. The MIR approach allows for a non-invasive analysis of the flow within packed spheres at the microscopic scales with high temporal and spatial resolution. Flow characteristics obtained from the TR-PIV measurements at various Reynolds numbers are presented. The results include the first- and second-order flow statistics, such as mean velocity, root-mean-square fluctuating velocity and Reynolds stresses. Effects of the wall boundary and Reynolds numbers on flow patterns are currently being investigated. Comparisons of the mean velocities, root-mean-square fluctuating velocities, and Reynolds stress components show the increase of flow mixing and turbulent intensities within the gaps between spheres in the packed bed. Sizes of recirculation regions, however, seem to be independent of the increase of Reynolds numbers.

An Explicit Non-Real Time Data Reduction Method of Triple Sensors Hot-Wire Anemometer in Three-Dimensional Flow

1988 ◽  
Vol 110 (2) ◽  
pp. 110-119 ◽  
Author(s):  
Y. T. Chew ◽  
R. L. Simpson
Keyword(s):  
Real Time ◽  
Three Dimensional ◽  
Computation Time ◽  
Reynolds Stresses ◽  
Hot Wire ◽  
Time Data ◽  
Three Dimensional Flow ◽  
Mean Velocity ◽  
Dimensional Flow ◽  
The Mean

An explicit non-real time method of reducing triple sensor hot-wire anenometer data to obtain the three mean velocity components and six Reynolds stresses, as well as their turbulence spectra in three-dimensional flow is proposed. Equations which relate explicitly the mean velocity components and Reynolds stresses in laboratory coordinates to the mean and mean square sensors output voltages in three stages are derived. The method was verified satisfactorily by comparison with single sensor hot-wire anemometer measurements in a zero pressure gradient incompressible turbulent boundary layer flow. It is simple and requires much lesser computation time when compared to other implicit non-real time method.

Hot-Wire Measurements Inside a Centrifugal Fan Impeller

1989 ◽  
Vol 111 (4) ◽  
pp. 363-368 ◽  
Author(s):  
A. Kjo¨rk ◽  
L. Lo¨fdahl
Keyword(s):  
Suction Side ◽  
Design Flow ◽  
Shear Stresses ◽  
Centrifugal Fan ◽  
Reynolds Stresses ◽  
Low Velocity ◽  
Mean Velocity ◽  
Attached Flow ◽  
The Mean ◽  
Velocity Region

Measurements of the three mean velocity components and five of the Reynolds stresses have been carried out in the blade passage of a centrifugal fan impeller. The impeller was of ordinary design, with nine backward curved blades, and all measurements were carried out at the design flow rate. The mean velocity measurements show that the flow can be characterized as an attached flow with almost linearly distributed velocity profiles. However, in a region near the suction side close to the shroud a low velocity region is created. From the turbulence measurements it can be concluded that relatively low values of the turbulent stresses are predominating in the center region of the channel. Closer to the walls higher values of the normal as well as shear stresses are noted.

Sign in / Sign up

Export Citation Format

Share Document