Dynamic Mechanical Characterization of CF/GF Hybrid Reinforced Polymeric Composite Structures

2012 ◽  
Author(s):  
Dana Luca Motoc
Keyword(s):  
Mechanical Properties ◽  
Composite Structures ◽  
Volume Fraction ◽  
Loss Modulus ◽  
Glass Fibers ◽  
Reference Sample ◽  
Polymeric Composite ◽  
Relative Volume Fraction ◽  
Dynamic Mechanical

The importance of dynamic mechanical analysis (DMA) as a research tool in the study of polymeric composite structures behavior has been already demonstrated in the literature. Many papers were approaching the relaxation phenomenon within the polymer based composite structures and thereby their behavior under various conditions of stress and temperature. Supplementary, the effect of fillers geometry, orientation and volume fraction have been extensively approached while considering the micromechanical level and their role in the mechanical properties were suitable stated. Hybridization of two different fillers has proven to an effective method in material design allowing their developers to tailor their properties according to the application driven imposed requirements. The herein paper attempts to present a comparative study centered on the development and characterization of a hybrid polymeric composite structures made up from different combinations of carbon and glass fibers by evaluating their dynamic mechanical properties. The samples were measured using the Dynamic Mechanical Analyzer (DMA) from NETZSCH-DMA 242 C, in the 3-point bending mode, nitrogen atmosphere, at a scanning rate of 3 K/min from −40 to 180° C with a fixed frequency of 1 Hz. Storage and loss modulus, loss tangent were recorded as function of temperature both on longitudinal and transverse direction of the unidirectional carbon fibers, in two consecutive heating cycles. A reference sample was set up to aid the comparison analysis, made entire from one filler type. The effect of the fillers type, fillers relative volume fraction and temperature on the storage and loss moduli will be deeply investigated.

scholarly journals PMMA-Y2O3 (Eu3+) nanocomposites: Optical and mechanical properties

2011 ◽  
Vol 76 (8) ◽  
pp. 1153-1161 ◽  
Author(s):  
Salah Musbah ◽  
Vesna Radojevic ◽  
Nadezda Borna ◽  
Dusica Stojanovic ◽  
Miroslav Dramicanin ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Loss Modulus ◽  
Emission Spectra ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Dynamic Mechanical ◽  
Microhardness Data ◽  
Nanoparticles Concentration ◽  
Optical And Mechanical Properties

The results of a study related to the processing and characterization of PMMA-Y2O3 (Eu3+) nanocomposites are presented herein. The nanocomposite samples were prepared using a laboratory mixing molder with different contents of Eu-ion doped Y2O3 nanophosphor powder. The influence of particle content on the optical and dynamic mechanical properties of the nanocomposites was investigated. The intensity of the luminescence emission spectra increased as the nanophosphor content in the composite increased. The results of dynamic mechanical analysis revealed that the storage modulus, loss modulus and glass transition temperature (Tg) of the polymer composites increased with increasing content of the nanophosphor powder. The microhardness data also confirmed that the hardness number increased with nanoparticles concentration in the PMMA nanocomposites. The obtained results revealed a relatively linear relationship between Tg and the Vickers hardness.

Fabrication of bionanocomposites reinforced with hemp nanocellulose and evaluation of their mechanical, thermal and dynamic mechanical properties

2021 ◽  
pp. 146442072110046
Author(s):  
SS Rana ◽  
MK Gupta
Keyword(s):  
Mechanical Properties ◽  
In Situ Polymerization ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
X Ray Diffraction ◽  
Dynamic Mechanical ◽  
Hemp Fibres ◽  
Polymerization Method

The present study aims to fabricate the epoxy-based bionanocomposites reinforced with hemp nanocellulose and the evaluation of their mechanical, thermal and dynamic mechanical properties. Nanocellulose from hemp fibres was isolated via the chemo-mechanical method and its bionanocomposites were prepared using the in situ polymerization method. Although many researchers have reported studies on the preparation and characterization of bionanocomposites however, studies on the mechanical, thermal, and dynamic mechanical properties of epoxy-based bionanocomposites reinforced with hemp nanocellulose are still unreported. The mechanical properties (i.e. tensile, flexural, hardness, and impact) and dynamic mechanical properties (i.e. glass transition temperature, damping behaviour, storage, and loss modulus) of the developed bionanocomposites were investigated. Further, the crystalline behaviour and thermal stability were also studied using the X-ray diffraction and thermogravimetric analysis techniques, respectively. The results revealed that an addition of nanocellulose considerably improved the mechanical, thermal, and viscoelastic properties of the bionanocomposites. As much as 52.17%, 48.17%, 89.08%, and 15.67% improvements in the tensile strength, flexural strength, impact strength, and hardness, respectively, for the 2 wt.% nanocellulose composites were found over the epoxy matrix.

scholarly journals Dynamic Mechanical Properties of Hybrid Layered Silicates/Kaolin Geopolymer Filler in Epoxy Composites

2017 ◽  
Vol 54 (3) ◽  
pp. 543-545 ◽  
Author(s):  
Yusrina Mat Daud ◽  
Kamarudin Hussin ◽  
Azlin Fazlina Osman ◽  
Che Mohd Ruzaidi Ghazali ◽  
Mohd Mustafa Al Bakri Abdullah ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
High Speed ◽  
Hybrid Composites ◽  
Loss Modulus ◽  
Dynamic Mechanical Properties ◽  
Mechanical Analysis ◽  
Layered Silicates ◽  
Epoxy Composites ◽  
Damping Factor ◽  
Dynamic Mechanical

Preparation epoxy based hybrid composites were involved kaolin geopolymer filler, organo-montmorillonite at 3phr by using high speed mechanical stirrer. A mechanical behaviour of neat epoxy, epoxy/organo-montmorillonite and its hybrid composites containing 1-8phr kaolin geopolymer filler was studied upon cyclic deformation (three-point flexion mode) as the temperature is varies. The analysis was determined by dynamic mechanical analysis (DMA) at frequency of 1.0Hz. The results then expressed in storage modulus (E�), loss modulus (E�) and damping factor (tan d) as function of temperature from 40 oC to 130oC. Overall results indicated that E�, E�� and Tg increased considerably by incorporating optimum 1phr kaolin geopolymer in epoxy organo-montmorillonite hybrid composites.

scholarly journals Manufacture and Mechanical Behavior of Green Polymeric Composite Reinforced with Hydrated Cotton Fiber

2019 ◽  
Vol 2 (1) ◽  
Author(s):  
Ênio Henrique Pires da Silva ◽  
Emiliano Barretto Almendro ◽  
Amanda Albertin Xavier da Silva ◽  
Guilherme Waldow ◽  
Flaminio CP Sales ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Tensile Strength ◽  
Cotton Fiber ◽  
Natural Fibers ◽  
Young Modulus ◽  
Polymeric Composite ◽  
Morphological Characterization ◽  
Comparison And Study ◽  
Fiber Fabric

Composites using natural fibers as reinforcement and biodegradable polymers as matrix are considered environmentally friendly materials. This paper seeks the mechanical and morphological characterization of a biocomposite of polyurethane (PU) derived from a blend of vegetable oils doped with aluminatrihydrate (ATH) and reinforced with hydrated cotton fiber fabric (HCF). The comparison and study were performed based on the properties of the: (i) pure PU; (ii) PU doped with ATH containing 30% of the final mass (PU+30%ATH); (iii) composite of PU reinforced with 7 layers of cotton fiber fabric (PU+7CF); (iv) composite of PU+30%ATH reinforced with 7 layers of CF (PU+30%ATH+7CF); (v) composite of PU+30%ATH reinforced with 7 layers of hydrated cotton fiber fabric (PU+30%ATH+7HCF). The mechanical properties obtained according to the tensile test for the composite PU+30%ATH+CF with fibers oriented at 0° showed a significant increment in tensile strength (60 MPa) and the modulus of elasticity (4.7 GPa) when compared to pure PU (40 MPa) and (1.7 GPa) respectively. PU+30%ATH also presented a rising tensile strength (31 MPa) and Young modulus (2.6 GPa). For the composite with addition of water, results presented a significant decrease in strength (31.3 MPa) and stiffness (0.9 GPa) than the composite with no water. Electron microscopy (SEM) analyses exhibited that the samples with addition of water showed the presence of large amounts of pores and the lower interaction between matrix and fiber. These results may explain the lower mechanical properties of this material. DOI: http://dx.doi.org/10.30609/JETI.2019-7576

scholarly journals Influence of Glass Fibers on Mechanical Properties of Concrete with Recycled Coarse Aggregates

2019 ◽  
Vol 5 (5) ◽  
pp. 1007-1019 ◽  
Author(s):  
Babar Ali ◽  
Liaqat Ali Qureshi ◽  
Ali Raza ◽  
Muhammad Asad Nawaz ◽  
Safi Ur Rehman ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Compressive Strength ◽  
Flexural Strength ◽  
Mechanical Performance ◽  
Volume Fraction ◽  
Glass Fibers ◽  
Construction Material ◽  
Concrete Compressive Strength ◽  
Coarse Aggregates ◽  
Highly Sensitive

Despite plain cement concrete presenting inferior performance in tension and adverse environmental impacts, it is the most widely used construction material in the world. Consumption of fibers and recycled coarse aggregates (RCA) can add ductility and sustainability to concrete. In this research, two mix series (100%NCA, and 100%RCA) were prepared using four different dosages of GF (0%GF, 0.25%GF, 0.5%GF, and 0.75%GF by volume fraction).  Mechanical properties namely compressive strength, splitting tensile strength, and flexural strength of each concrete mixture was evaluated at the age of 28 days. The results of testing indicated that the addition of GF was very useful in enhancing the split tensile and flexural strength of both RCA and NCA concrete. Compressive strength was not highly sensitive to the addition of GF. The loss in strength that occurred due to the incorporation of RCA was reduced to a large extent upon the inclusion of GF. GF caused significant improvements in the split tensile and flexural strength of RCA concrete. Optimum dosage of GF was determined to be 0.25% for NCA, and 0.5% for RCA concrete respectively, based on the results of combined mechanical performance (MP).

Biomimetic composites inspired by venous leaf

2017 ◽  
Vol 52 (3) ◽  
pp. 361-372 ◽  
Author(s):  
Gongdai Liu ◽  
R Ghosh ◽  
A Vaziri ◽  
A Hossieni ◽  
D Mousanezhad ◽  
...  
Keyword(s):  
Mechanical Properties ◽  
Elastic Modulus ◽  
Yield Stress ◽  
Poisson’S Ratio ◽  
Composite Structures ◽  
Volume Fraction ◽  
Matrix Material ◽  
Poisson's Ratio ◽  
Fiber Volume ◽  
Young’S Moduli

A typical plant leaf can be idealized as a composite having three principal fibers: the central mid-fiber corresponding to the mid-rib, straight parallel secondary fibers attached to the mid-fiber representing the secondary veins, and then another set of parallel fibers emanating from the secondary fibers mimicking the tertiary fibers embedded in a matrix material. This paper introduces a biomimetic composite design inspired by the morphology of venous leafs and investigates the effects of venation morphologies on the in-plane mechanical properties of the biomimetic composites using finite element method. The mechanical properties such as Young’s moduli, Poisson’s ratio, and yield stress under uniaxial loading of the resultant composite structures was studied and the effect of different fiber architectures on these properties was investigated. To this end, two broad types of architectures were used both having similar central main fiber but differing in either having only secondary fibers or additional tertiary fibers. The fiber and matrix volume fractions were kept constant and a comparative parametric study was carried out by varying the inclination of the secondary fibers. The results show that the elastic modulus of composite in the direction of main fiber increases linearly with increasing the angle of the secondary fibers. Furthermore, the elastic modulus is enhanced if the secondary fibers are closed, which mimics composites with closed cellular fibers. In contrast, the elastic modulus of composites normal to the main fiber ( x direction) exponentially decreases with the increase of the angle of the secondary fibers and it is little affected by having secondary fibers closed. Similar results were obtained for the yield stress of the composites. The results also indicate that Poisson’s ratio linearly increases with the secondary fiber angle. The results also show that for a constant fiber volume fraction, addition of various tertiary fibers may not significantly enhance the mechanical properties of the composites. The mechanical properties of the composites are mainly dominated by the secondary fibers. Finally, a simple model was proposed to predict these behaviors.

Sign in / Sign up

Export Citation Format

Share Document