Performance Evaluation of an Air Source Heat Pump Coupled With a Building Integrated Photovoltaic/Thermal (BIPV/T) System

2014 ◽  
Author(s):  
Getu Hailu ◽  
Peter Dash ◽  
Alan S. Fung
Keyword(s):  
Performance Evaluation ◽  
Heat Pump ◽  
Ambient Air ◽  
Coefficient Of Performance ◽  
Air Source Heat Pump ◽  
Photovoltaic Arrays ◽  
Variable Capacity ◽  
Building Integrated Photovoltaic ◽  
Heating Mode ◽  
T System

A theoretical investigation of a variable capacity air-to-air air source heat pump (VC-ASHP) coupled with a building integrated photovoltaic/thermal (BIPV/T) system is presented in this paper. The BIPV/T system was integrated into the roof and the wall. Air was circulated behind the photovoltaic arrays to recover the thermal energy. The warm air recovered was supplied to the VC-ASHP. The thermal performance of the VC-ASHP was investigated for three scenarios when the heat pump is running in heating mode. The three scenarios are: (A) by feeding the ambient air to the ASHP; (B) by coupling the ASHP to the wall integrated BIPV/T only; and (C) by coupling the ASHP to the roof integrated BIPV/T only. The coefficient of performance (COP) of the VC-ASHP was evaluated for these three separate scenarios and compared. A typical winter day result suggests that the COP of the ASHP can be improved by coupling the VC-ASHP to either of the BIPV/T systems, i.e., either to the roof integrated BIPV/T system or to the wall integrated BIPV/T system.

scholarly journals Performance analysis of a two-stage variable capacity air source heat pump and a horizontal loop coupled ground source heat pump system

2021 ◽  
Author(s):  
Amir Alizadeh Safa
Keyword(s):  
Heat Pump ◽  
Ground Source Heat Pump ◽  
Outdoor Temperature ◽  
Cooling Mode ◽  
Two Stage ◽  
Pump System ◽  
Air Source Heat Pump ◽  
Ground Source ◽  
Variable Capacity ◽  
Heating Mode

The thermal performance of a new two-stage variable capacity air source heat pump (ASHP) and a horizontal ground loop ground source heat pump (GSHP) was investigated side-by-side at the Archetype Sustainable Twin Houses located in Toronto, Canada. The heat pumps were tested in cooling mode, as well as heating mode under extreme winter conditions. In cooling mode, the ASHP COP ranged from 4.7 to 5.7 at an outdoor temperature of 33 degrees C and 16 degrees C respectively, while the GSHP COP ranged from 4.9 (at an ELT of 8.5 degrees C and EST of 19.2 degrees C) to 5.6 (at an ELT of 12. 4 degrees C and EST of 17.8 degrees C). In heating mode, the ASHP COP ranged from 1.79 to 5.0 at an outdoor temperature of -19 degrees C and 9 degrees C respectively, while the GSHP COP ranged from 3.05 (at an ELT of 44.4 degrees C and an EST of 2.7 degrees C) to 3.44 (at an ELT of 41.5 degrees C and an EST of 5.48 degrees C) during the earlier winter test period. Data extrapolation and energy simulation was also performed to predict annual heat pump performance in Toronto as well as other Canadian regions.

scholarly journals Combined building integrated photovoltaic-thermal collector with air source heat pump for cold climate

2021 ◽  
Author(s):  
Raghad Sabah Kamel
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Electricity Consumption ◽  
Test Facility ◽  
Air Source Heat Pump ◽  
Building Integrated Photovoltaic ◽  
In Series ◽  
T System

A TRNSYS model was developed to conduct a comprehensive study of combining a building integrated photovoltaic thermal (BIPV/T) collector with an air source heat pump (ASHP) in an Archetype Sustainable House. The heat pump uses the warm air generated in the BIPV/T as the source for heat production. The coupling of BIPV/T and ASHP enables a highly efficient heating system in winter conditions. A numerical model was developed for an air-based PV/T collector. The model was used to predict the thermal and electrical performance of the collector and to conduct a comprehensive analysis for different configurations (number of PV/T panels in rows NR and in series NS) and different design parameters. TRNSYS simulation results showed that low air mass flow rate and low duct depth enhance the heat pump coefficient of performance (COP). The arrangement with a large number of PV/T systems connected in series has higher COP. The maximum obtained seasonal heating COP was 3.45, corresponding to duct depth of 1.5 in, NS=5 and low row mass flow rate of 0.03 kg/s. The heat pump cumulative electricity consumption for a typical heating season could be reduced by 20.2%. When the analysis was based only on sunny hours, the electricity consumption of the combined ASHP + PV/T system was reduced by 52% and the predicted seasonal COP of the heat pump was 5.98. A new full-scale test facility was presented to be implemented at Toronto and Region Conservation Authority to examine the performance of combining passive system and dynamic building envelope technologies (BIPV/T+ASHP+TES) under real weather conditions. It is important to match the maximum airflow for the BIPV/T system with the maximum airflow for the outdoor coil of the heat pump. The pressure drop inside the PV/T collector along with the connecting air duct from the BIPV/T to ASHP for a wide range of airflow rates and different duct depths was calculated. It was found that for air a flow rate around 2000 CFM, which is the maximum CFM for the custom-made ASHP for the test facility, the predicted fan energy was 195 kWh/year corresponding to 1.5 in. duct depth.

scholarly journals A Prototype Of Propane Refrigerant Based ASHP With Heat Recovery Ventilation (HRV) System

2021 ◽  
Author(s):  
Ali Karevan
Keyword(s):  
Heat Pump ◽  
Ozone Depletion ◽  
Operating Conditions ◽  
Carbon Reduction ◽  
Air Source Heat Pump ◽  
Heat Pump Unit ◽  
Building Integrated Photovoltaic ◽  
Thermodynamic Performance ◽  
Ozone Depletion Potential ◽  
T System

In recent years, an increased focus has been given to replacing high Global Warming Potential (GWP) refrigerants with relatively low GWP alternatives. Energy efficiency, carbon reduction and HFC phase-down will push the heat pump market towards natural refrigerants. Propane (R-290) is a type of hydrocarbon refrigerant with zero ozone depletion potential and very low GWP (< 4). R-290 is a pure refrigerant and has excellent thermodynamic properties. The research presented in this project is a study of the refrigerant side of an ASHP to analyze the thermodynamic performance of the propane refrigerant under different operating conditions. For this purpose, a test rig was designed and constructed in a single packaged air source heat pump unit. In addition, the air side of the tested heat pump was designed for energy recovery in cooling and heating modes. The compactness of the system and installation of air dampers allows its placement for coupling to the building renewable air sources, such as a building integrated photovoltaic/thermal (BIPV/T) system.

scholarly journals Analysis of air-to-water heat pump in cold climate: comparison between experiment and simulation

2015 ◽  
Vol 7 (4) ◽  
pp. 468-474
Author(s):  
Karolis Januševičius ◽  
Giedrė Streckienė
Keyword(s):  
Simulation Model ◽  
Heat Pump ◽  
Performance Prediction ◽  
Cold Climate ◽  
Coefficient Of Performance ◽  
Outdoor Temperature ◽  
Climate Conditions ◽  
Air Source Heat Pump ◽  
Seasonal Performance ◽  
Heating Mode

Heat pump systems are promising technologies for current and future buildings and this research presents the performance of air source heat pump (ASHP) system. The system was monitored, analysed and simulated using TRNSYS software. The experimental data were used to calibrate the simulation model of ASHP. The specific climate conditions are evaluated in the model. It was noticed for the heating mode that the coefficient of performance (COP) varied from 1.98 to 3.05 as the outdoor temperature changed from –7.0 ºC to +5.0 ºC, respectively. TRNSYS simulations were also performed to predict seasonal performance factor of the ASHP for Vilnius city. It was identified that seasonal performance prediction could be approximately 15% lower if frost formation effects are not included to air-water heat pump simulation model.

scholarly journals Performance analysis of a two-stage variable capacity air source heat pump and a horizontal loop coupled ground source heat pump system

2021 ◽  
Author(s):  
Amir Alizadeh Safa
Keyword(s):  
Heat Pump ◽  
Ground Source Heat Pump ◽  
Outdoor Temperature ◽  
Cooling Mode ◽  
Two Stage ◽  
Pump System ◽  
Air Source Heat Pump ◽  
Ground Source ◽  
Variable Capacity ◽  
Heating Mode

The thermal performance of a new two-stage variable capacity air source heat pump (ASHP) and a horizontal ground loop ground source heat pump (GSHP) was investigated side-by-side at the Archetype Sustainable Twin Houses located in Toronto, Canada. The heat pumps were tested in cooling mode, as well as heating mode under extreme winter conditions. In cooling mode, the ASHP COP ranged from 4.7 to 5.7 at an outdoor temperature of 33 degrees C and 16 degrees C respectively, while the GSHP COP ranged from 4.9 (at an ELT of 8.5 degrees C and EST of 19.2 degrees C) to 5.6 (at an ELT of 12. 4 degrees C and EST of 17.8 degrees C). In heating mode, the ASHP COP ranged from 1.79 to 5.0 at an outdoor temperature of -19 degrees C and 9 degrees C respectively, while the GSHP COP ranged from 3.05 (at an ELT of 44.4 degrees C and an EST of 2.7 degrees C) to 3.44 (at an ELT of 41.5 degrees C and an EST of 5.48 degrees C) during the earlier winter test period. Data extrapolation and energy simulation was also performed to predict annual heat pump performance in Toronto as well as other Canadian regions.

scholarly journals Combined building integrated photovoltaic-thermal collector with air source heat pump for cold climate

2021 ◽  
Author(s):  
Raghad Sabah Kamel
Keyword(s):  
Mass Flow Rate ◽  
Heat Pump ◽  
Mass Flow ◽  
Flow Rate ◽  
Electricity Consumption ◽  
Test Facility ◽  
Air Source Heat Pump ◽  
Building Integrated Photovoltaic ◽  
In Series ◽  
T System

A TRNSYS model was developed to conduct a comprehensive study of combining a building integrated photovoltaic thermal (BIPV/T) collector with an air source heat pump (ASHP) in an Archetype Sustainable House. The heat pump uses the warm air generated in the BIPV/T as the source for heat production. The coupling of BIPV/T and ASHP enables a highly efficient heating system in winter conditions. A numerical model was developed for an air-based PV/T collector. The model was used to predict the thermal and electrical performance of the collector and to conduct a comprehensive analysis for different configurations (number of PV/T panels in rows NR and in series NS) and different design parameters. TRNSYS simulation results showed that low air mass flow rate and low duct depth enhance the heat pump coefficient of performance (COP). The arrangement with a large number of PV/T systems connected in series has higher COP. The maximum obtained seasonal heating COP was 3.45, corresponding to duct depth of 1.5 in, NS=5 and low row mass flow rate of 0.03 kg/s. The heat pump cumulative electricity consumption for a typical heating season could be reduced by 20.2%. When the analysis was based only on sunny hours, the electricity consumption of the combined ASHP + PV/T system was reduced by 52% and the predicted seasonal COP of the heat pump was 5.98. A new full-scale test facility was presented to be implemented at Toronto and Region Conservation Authority to examine the performance of combining passive system and dynamic building envelope technologies (BIPV/T+ASHP+TES) under real weather conditions. It is important to match the maximum airflow for the BIPV/T system with the maximum airflow for the outdoor coil of the heat pump. The pressure drop inside the PV/T collector along with the connecting air duct from the BIPV/T to ASHP for a wide range of airflow rates and different duct depths was calculated. It was found that for air a flow rate around 2000 CFM, which is the maximum CFM for the custom-made ASHP for the test facility, the predicted fan energy was 195 kWh/year corresponding to 1.5 in. duct depth.

scholarly journals A Prototype Of Propane Refrigerant Based ASHP With Heat Recovery Ventilation (HRV) System

2021 ◽  
Author(s):  
Ali Karevan
Keyword(s):  
Heat Pump ◽  
Ozone Depletion ◽  
Operating Conditions ◽  
Carbon Reduction ◽  
Air Source Heat Pump ◽  
Heat Pump Unit ◽  
Building Integrated Photovoltaic ◽  
Thermodynamic Performance ◽  
Ozone Depletion Potential ◽  
T System

In recent years, an increased focus has been given to replacing high Global Warming Potential (GWP) refrigerants with relatively low GWP alternatives. Energy efficiency, carbon reduction and HFC phase-down will push the heat pump market towards natural refrigerants. Propane (R-290) is a type of hydrocarbon refrigerant with zero ozone depletion potential and very low GWP (< 4). R-290 is a pure refrigerant and has excellent thermodynamic properties. The research presented in this project is a study of the refrigerant side of an ASHP to analyze the thermodynamic performance of the propane refrigerant under different operating conditions. For this purpose, a test rig was designed and constructed in a single packaged air source heat pump unit. In addition, the air side of the tested heat pump was designed for energy recovery in cooling and heating modes. The compactness of the system and installation of air dampers allows its placement for coupling to the building renewable air sources, such as a building integrated photovoltaic/thermal (BIPV/T) system.

scholarly journals Studying a Hybrid System Based on Solid Oxide Fuel Cell Combined With an Air Source Heat Pump and With a Novel Heat Recovery

2018 ◽  
Vol 16 (2) ◽  
Author(s):  
Giulio Vialetto ◽  
Marco Noro ◽  
Masoud Rokni
Keyword(s):  
Fuel Cell ◽  
Solid Oxide Fuel Cell ◽  
Electric Power ◽  
Heat Pump ◽  
Heat Recovery ◽  
Research Work ◽  
Solid Oxide ◽  
Coefficient Of Performance ◽  
Oxide Fuel ◽  
Air Source Heat Pump

In this paper, a new heat recovery for a microcogeneration system based on solid oxide fuel cell and air source heat pump (HP) is presented with the main goal of improving efficiency on energy conversion for a residential building. The novelty of the research work is that exhaust gases after the fuel cell are first used to heat water for heating/domestic water and then mixed with the external air to feed the evaporator of the HP with the aim of increasing energy efficiency of the latter. This system configuration decreases the possibility of freezing of the evaporator as well, which is one of the drawbacks for air source HP in Nordic climates. A parametric analysis of the system is developed by performing simulations varying the external air temperature, air humidity, and fuel cell nominal power. Coefficient of performance (COP) can increase more than 100% when fuel cell electric power is close to its nominal (50 kW), and/or inlet air has a high relative humidity (RH) (close to 100%). Instead, the effect of mixing the exhausted gases with air may be negative (up to −25%) when fuel cell electric power is 20 kW and inlet air has 25% RH. Thermodynamic analysis is carried out to prove energy advantage of such a solution with respect to a traditional one, resulting to be between 39% and 44% in terms of primary energy. The results show that the performance of the air source HP increases considerably during cold season for climates with high RH and for users with high electric power demand.

Sign in / Sign up

Export Citation Format

Share Document