Thermal and Mechanical Characterization of Contiguous Wall Systems for Energy Efficient Low Cost Housing

2011 ◽  
Author(s):  
Barzin Mobasher ◽  
Geoffrey Minor ◽  
Mansour Zenouzi ◽  
Salvador L. Jalife
Keyword(s):  
Finite Element ◽  
Structural Model ◽  
Low Cost ◽  
Structural Walls ◽  
Element Analysis ◽  
Fully Integrated ◽  
Alternative Technologies ◽  
Laminate Theory ◽  
Low Cost Housing ◽  
Transient Thermal

The interaction of alternative technologies for low cost housing using a fully integrated finite element thermal and structural model of the system. The such as matrix formulations, or different wall systems can be accomplished using. Multi-layer systems based on composite laminate theory are used as a substitution for both reinforcement and effective thermal barrier of structural walls and roof systems. Textile Reinforced Cement composites (TRCs) as thin sandwich skin elements are considered since they show improved tension capacity and ductility based a well-bonded and well-distributed reinforcement that minimizes the flaw sizes, leading to the increase in overall strength and ductility. A range of innovative materials are used in a transient thermal analysis of the composite wall system. Using both 2-D and 3-D finite element analysis, field data obtained from interior and exterior faces of three model construction systems are simulated for walls and roof members as a function of time. Using the exterior temperature as the imposed boundary condition, the interior temperatures were predicted and compared with the experimentally obtained results. Sensitivity of the model to changes in parameters is studied for various insulating materials.

Use of the Finite Element Analysis Method in Pedodontics

2018 ◽  
Vol 55 (4) ◽  
pp. 666-675
Author(s):  
Mihaela Tanase ◽  
Dan Florin Nitoi ◽  
Marina Melescanu Imre ◽  
Dorin Ionescu ◽  
Laura Raducu ◽  
...  
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Structural Model ◽  
Analysis Method ◽  
Ansys Software ◽  
Concentrated Force ◽  
Element Analysis ◽  
Finite Element Analysis Method ◽  
The Finite Element Analysis ◽  
Solid Type

The purpose of this study was to determinate , using the Finite Element Analysis Method, the mechanical stress in a solid body , temporary molar restored with the self-curing GC material. The originality of our study consisted in using an accurate structural model and applying a concentrated force and a uniformly distributed pressure. Molar structure was meshed in a Solid Type 45 and the output data were obtained using the ANSYS software. The practical predictions can be made about the behavior of different restorations materials.

Fitness for Service Assessments of Bulging and Out-of-Round Structures

2004 ◽  
Author(s):  
Peter Carter ◽  
D. L. Marriott ◽  
M. J. Swindeman
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Internal Pressure ◽  
Structural Model ◽  
External Pressure ◽  
Element Analysis ◽  
Structural Imperfection ◽  
Level 2

This paper examines techniques for the evaluation of two kinds of structural imperfection, namely bulging subject to internal pressure, and out-of-round imperfections subject to external pressure, with and without creep. Comparisons between comprehensive finite element analysis and API 579 Level 2 techniques are made. It is recommended that structural, as opposed to material, failures such as these should be assessed with a structural model that explicitly represents the defect.

Mechanical and Optimization Analyses for Novel Wound Composite Axial Impeller

2009 ◽  
Author(s):  
Jifeng Wang ◽  
Qubo Li ◽  
Norbert Mu¨ller
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Speed ◽  
High Performance ◽  
Low Cost ◽  
Three Dimensional ◽  
Von Mises Stress ◽  
Loading Conditions ◽  
Element Analysis ◽  
Wound Composite

A mechanical and optimal analyses procedure is developed to assess the stresses and deformations of Novel Wound Composite Axial-Impeller under loading conditions particular to centrifuge. This procedure is based on an analytical method and Finite Element Analysis (FEA, commercial software ANSYS) results. A low-cost, light-weight, high-performance, composite turbomachinery impeller from differently designed patterns will be evaluated. Such impellers can economically enable refrigeration plants using water as a refrigerant (R718). To create different complex patterns of impellers, MATLAB is used for creating the geometry of impellers, and CAD software UG is used to build three-dimensional impeller models. Available loading conditions are: radial body force due to high speed rotation about the cylindrical axis and fluid forces on each blade. Two-dimensional plane stress and three-dimensional stress finite element analysis are carried out using ANSYS to validate these analytical mechanical equations. The von Mises stress is investigated, and maximum stress and Tsai-Wu failure criteria are applied for composite material failure, and they generally show good agreement.

Finite Element Analysis of Transient Thermal Problems of Work Rolls in Hot Rolling Process

1999 ◽  
Author(s):  
James D. Lee ◽  
Majid T. Manzari ◽  
Yin-Lin Shen ◽  
Wenjun Zeng
Keyword(s):  
Finite Element ◽  
Hot Rolling ◽  
Three Dimensional ◽  
Thermal Characteristics ◽  
Rolling Process ◽  
Thermal Problem ◽  
Element Analysis ◽  
Hot Rolling Process ◽  
Transient Thermal ◽  
Work Rolls

Abstract The three-dimensional transient thermal problem of work rolls in the entire hot rolling process has been formulated. It includes the time-varying boundary conditions specified at the roll surface taking the schedule of both rolling and idling cycles into consideration. The corresponding finite element equations are derived and solved by the Runge-Kutta-Verner method. The finite element solutions indicate that the temperature variations in the circumferential direction are overwhelming. Case studies unveil the thermal characteristics of the work rolls in various kinds of mill operations. Numerical results are presented and compared with Guo’s analytical solutions.

Comprehending Occurrence of Premature Failure in Compressor Turbine (CT) Blades for Short-Haul Aircraft Fleet

2019 ◽  
Vol 42 ◽  
pp. 10-23
Author(s):  
Joshua Kimtai Ngoret ◽  
Venkata Parasuram Kommula
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
High Pressure ◽  
Thermal Stresses ◽  
Geometrical Model ◽  
Mechanical Stresses ◽  
Element Analysis ◽  
Premature Failure ◽  
Structural Stresses ◽  
Transient Thermal

This paper presents results from modeling of Compressor Turbine (CT) blades for short-haul aircraft fleet occasioned by thermo-mechanical stresses in order to comprehend the occurrence of premature failure. A 3D PT6A-114A engine high pressure (HP) CT blade geometrical model was developed in commercial CAD-SolidWorks, then imported to ANSYS 15.0 environment for finite element analysis (FEA). The CT blade was investigated for transient thermal stresses from heat generated by the combustors and static structural stresses from rotational velocities of the engine which account for 80% of inertial field during flight. The results revealed that the blades could have served for another 1.44% of the time they were in service.

A Determination of Material Properties of Flexible Structures Using EMA and FEM Analysis

2014 ◽  
Vol 693 ◽  
pp. 293-298 ◽  
Author(s):  
Rastislav Duris
Keyword(s):  
Finite Element ◽  
Material Properties ◽  
Low Cost ◽  
Flexible Structures ◽  
Fem Analysis ◽  
Element Analysis ◽  
Structural Dynamic ◽  
Vibration Data ◽  
Complex Interactions ◽  
Applied Forces

Dynamic behavior of mechanical structures results from complex interactions between applied forces and the stiffness properties of the structure. Currently, many problems of structural dynamic analysis are solved using Finite Element Method (FEM). However, in recent years, the implementation of the Fast Fourier Transform (FFT) in low cost computer-based signal analyzers has provided a powerful tool for acquisition and analysis of vibration data. This article discusses combination of two approaches to structural dynamics testing; the experimental part which is referred to as Experimental Modal Analysis (EMA), respectively the analytical part, which is realized by Finite Element Analysis (FEA). Main goal of the paper is calculation of material properties from experimentally determined modal frequencies.

Considerations on Using the Strut and Tie Method for Modelling Coupling Beams

2017 ◽  
Vol 21 ◽  
pp. 116-121
Author(s):  
Vasile Murăraşu ◽  
Vasile Mircea Venghiac
Keyword(s):  
Finite Element Analysis ◽  
Finite Element ◽  
Linear Analysis ◽  
Numerical Analyses ◽  
Coupling Beam ◽  
Coupling Beams ◽  
Structural Walls ◽  
Element Analysis ◽  
Linear Elastic ◽  
Strut And Tie

This paper presents a synthesis of the numerical analyses regarding the method of modelling the coupling beams of structural walls. The directions of the struts and ties are established according to the results obtained after a linear-elastic finite element analysis. The results obtained after modelling using the Strut and Tie Method, with the struts and ties oriented along the diagonals of the coupling beam, coincide with the results obtained by applying the theory provided by EC8, which proves the viability of the method. This is also confirmed by the results obtained after a non-linear analysis was carried out in the LUSAS finite element environment.

Sign in / Sign up

Export Citation Format

Share Document