Estimation and Analysis of Vehicle Lateral Stability Region With Both Front and Rear Wheel Steering

2017 ◽  
Author(s):  
Yiwen Huang ◽  
Yan Chen
Keyword(s):  
Real Time ◽  
Stability Region ◽  
Equilibrium Points ◽  
Estimation Method ◽  
Rear Wheel ◽  
Linearization Method ◽  
Lateral Stability ◽  
Stability Regions ◽  
Explicit Analysis ◽  
Local Linearization Method

In this paper, a novel vehicle lateral stability region estimation method considering both front and rear wheel steering is introduced. Vehicle lateral stability regions are estimated by a local linearization method, which guarantees both vehicle local stability and handling stability. The impacts of front and rear wheel steering angles on stability region estimations are formulated and discussed. To quantitatively explain the shifting feature of stability regions under different front/rear steering angles, an explicit analysis about how the equilibrium points and the geometric centers of stability regions change with respect to different steering angles is formulated. The obtained relationship enables the estimation of stability regions in real time for varying front/rear steering angles. The additional rear wheel steering helps to maintain vehicle states stay within estimated stability regions. To show the effectiveness of the proposed real-time stability region estimation method and stability analysis, a Simulink and CarSim® co-simulation is applied to verify that vehicle states are covered within varying stability regions for a single lane change maneuver.

Stability Regions of Vehicle Lateral Dynamics: Estimation and Analysis

2020 ◽  
Vol 143 (5) ◽  
Author(s):  
Yiwen Huang ◽  
Wei Liang ◽  
Yan Chen
Keyword(s):  
Load Transfer ◽  
Equilibrium Points ◽  
Longitudinal Velocity ◽  
Linearization Method ◽  
Stability Control ◽  
Stable Operation ◽  
Lateral Stability ◽  
Ground Vehicles ◽  
Stability Regions ◽  
Road Friction

Abstract A new method is proposed to estimate and analyze the vehicle lateral stability region, which provides a direct and intuitive demonstration for the safety and stability control of ground vehicles. Based on a four-wheel vehicle model and a nonlinear two-dimensional (2D) analytical LuGre tire model, a local linearization method is applied to estimate the vehicle lateral stability regions by analyzing the vehicle stability at each operation point on a phase plane, which includes but not limited to the equilibrium points. As the collections of all the locally stable operation points, the estimated stability regions are conservative because both vehicle and tire stability are simultaneously considered, which are especially important for characterizing the stability features of highly/fully automated ground vehicles (AGV). The obtained lateral stability regions can be well explained by the vehicle characteristics of oversteering and understeering in the context of vehicle handling stability. The impacts of vehicle lateral load transfer, longitudinal velocity, tire-road friction coefficient, and steering angle on the estimated stability regions are presented and discussed. To validate the correctness of the estimated stability regions, a case study by matlab/simulink and CarSim® co-simulation is presented and discussed.

Vehicle Lateral Motion Control Based on Estimated Stability Regions

2017 ◽  
Author(s):  
Yiwen Huang ◽  
Yan Chen
Keyword(s):  
Measurement Errors ◽  
Local Stability ◽  
Stability Region ◽  
Control Method ◽  
Linearization Method ◽  
Stability Control ◽  
Lateral Stability ◽  
Shortest Distance ◽  
The Stability ◽  
Yaw Moment

This paper presents a novel vehicle lateral stability control method based on an estimated lateral stability region on the phase plane of vehicle yaw rate and lateral speed, which is obtained through a local linearization method. Since the estimated stability region does not only describe vehicle local stability, but also define the oversteering and understeering characteristics, the proposed control method can achieve both local stability and vehicle handling stability. Considering the irregular geometric shape of the estimated stability region, a stability analysis algorithm is designed to determine the distance between vehicle states and stability region boundaries. State estimation or measurement errors are also incorporated in the distance calculation. Based on the calculated shortest distance between vehicle states and stability boundaries, a direct yaw moment controller is designed to maintain vehicle states stay within the stability region. CarSim® and Simulink® co-simulation is applied to verify the control design through a cornering maneuver. The simulation results show that the proposed control method can make the vehicle stay within the stability region successfully and thus always operate in a safe manner.

JOINT ESTIMATION OF THE TRANSMISSIBILITY AND SEVERITY OF EBOLA VIRUS DISEASE IN REAL TIME

2017 ◽  
Vol 25 (04) ◽  
pp. 587-603 ◽  
Author(s):  
YUSUKE ASAI ◽  
HIROSHI NISHIURA
Keyword(s):  
Real Time ◽  
Ebola Virus ◽  
Virus Disease ◽  
Critical Role ◽  
Estimation Method ◽  
Case Fatality ◽  
Ascertainment Bias ◽  
Joint Estimation ◽  
Ebola Virus Disease ◽  
Strong Impact

The effective reproduction number [Formula: see text], the average number of secondary cases that are generated by a single primary case at calendar time [Formula: see text], plays a critical role in interpreting the temporal transmission dynamics of an infectious disease epidemic, while the case fatality risk (CFR) is an indispensable measure of the severity of disease. In many instances, [Formula: see text] is estimated using the reported number of cases (i.e., the incidence data), but such report often does not arrive on time, and moreover, the rate of diagnosis could change as a function of time, especially if we handle diseases that involve substantial number of asymptomatic and mild infections and large outbreaks that go beyond the local capacity of reporting. In addition, CFR is well known to be prone to ascertainment bias, often erroneously overestimated. In this paper, we propose a joint estimation method of [Formula: see text] and CFR of Ebola virus disease (EVD), analyzing the early epidemic data of EVD from March to October 2014 and addressing the ascertainment bias in real time. To assess the reliability of the proposed method, coverage probabilities were computed. When ascertainment effort plays a role in interpreting the epidemiological dynamics, it is useful to analyze not only reported (confirmed or suspected) cases, but also the temporal distribution of deceased individuals to avoid any strong impact of time dependent changes in diagnosis and reporting.

scholarly journals Real-time Array Shape Estimation Method of Horizontal Suspended Linear Array Based on Non-acoustic Auxiliary Sensors

IEEE Access ◽  
2021 ◽  
pp. 1-1
Author(s):  
Zonglun Che ◽  
Jun Wang ◽  
Jing Zhu ◽  
Bingbing Zhang ◽  
Yang Zhang ◽  
...  
Keyword(s):  
Real Time ◽  
Linear Array ◽  
Estimation Method ◽  
Shape Estimation ◽  
Array Shape Estimation

scholarly journals Analysis of Selected Methods Use for Calculation of the Coefficients of Adsorption Isotherms and Simplified Equations of Adsorption Dynamics with the Use of IZO Application

Materials ◽  
2021 ◽  
Vol 14 (15) ◽  
pp. 4192
Author(s):  
Jacek Piekarski ◽  
Katarzyna Ignatowicz ◽  
Tomasz Dąbrowski
Keyword(s):  
Linear System ◽  
Adsorption Isotherms ◽  
Balance Equation ◽  
Laboratory Tests ◽  
Adsorption Process ◽  
Estimation Method ◽  
Linearization Method ◽  
Sufficient Accuracy ◽  
Mass Balance Equation ◽  
Adsorption Dynamics

The purpose of this paper is to present the IZO application that calculates and visualizes coefficients of adsorption isotherms according to Freundlich, Langmuir, and BET in a classic and linear system, in a simple communicative way. The application also calculates the working time of the adsorption bed based on the transformation of the mass balance equation, and according to the Zuchowicki, Zabieziński, Tichonow, and the Bohart-Adams equations. The laboratory tests of the adsorption process of leachate from a municipal landfill on selected active coals ORGANOSORB 10, DESOTEK, and BA-10, were conducted to check the program for accuracy. Results of tests confirm that the linearization method of the calculation of adsorption isotherms coefficients, used in the IZO application, gives sufficient accuracy and may be used as an alternative of, e.g., the nonlinear estimation method.

scholarly journals Improvement of Reliability Determination Performance of Real Time Kinematic Solutions Using Height Trajectory

Sensors ◽  
2021 ◽  
Vol 21 (2) ◽  
pp. 657
Author(s):  
Aoki Takanose ◽  
Yoshiki Atsumi ◽  
Kanamu Takikawa ◽  
Junichi Meguro
Keyword(s):  
Real Time ◽  
Urban Areas ◽  
Estimation Method ◽  
Tall Buildings ◽  
Autonomous Driving ◽  
Reliability Estimation ◽  
Height Variation ◽  
Position Information ◽  
Real Time Kinematic ◽  
Evaluation Test

Autonomous driving support systems and self-driving cars require the determination of reliable vehicle positions with high accuracy. The real time kinematic (RTK) algorithm with global navigation satellite system (GNSS) is generally employed to obtain highly accurate position information. Because RTK can estimate the fix solution, which is a centimeter-level positioning solution, it is also used as an indicator of the position reliability. However, in urban areas, the degradation of the GNSS signal environment poses a challenge. Multipath noise caused by surrounding tall buildings degrades the positioning accuracy. This leads to large errors in the fix solution, which is used as a measure of reliability. We propose a novel position reliability estimation method by considering two factors; one is that GNSS errors are more likely to occur in the height than in the plane direction; the other is that the height variation of the actual vehicle travel path is small compared to the amount of movement in the horizontal directions. Based on these considerations, we proposed a method to detect a reliable fix solution by estimating the height variation during driving. To verify the effectiveness of the proposed method, an evaluation test was conducted in an urban area of Tokyo. According to the evaluation test, a reliability judgment rate of 99% was achieved in an urban environment, and a plane accuracy of less than 0.3 m in RMS was achieved. The results indicate that the accuracy of the proposed method is higher than that of the conventional fix solution, demonstratingits effectiveness.

High-precision roll attitude estimation of decoupled canards relative to the projectile body using bipolar hall-effect sensors

2021 ◽  
pp. 1-9
Author(s):  
Tingting Yin ◽  
Zhong Yang ◽  
Youlong Wu ◽  
Fangxiu Jia
Keyword(s):  
Hall Effect ◽  
Real Time ◽  
High Precision ◽  
Solution Method ◽  
Estimation Method ◽  
Estimation Algorithm ◽  
Attitude Estimation ◽  
Fuzzy Algorithms ◽  
Positioning Method ◽  
Hall Effect Sensors

The high-precision roll attitude estimation of the decoupled canards relative to the projectile body based on the bipolar hall-effect sensors is proposed. Firstly, the basis engineering positioning method based on the edge detection is introduced. Secondly, the simplified dynamic relative roll model is established where the feature parameters are identified by fuzzy algorithms, while the high-precision real-time relative roll attitude estimation algorithm is proposed. Finally, the trajectory simulations and grounded experiments have been conducted to evaluate the advantages of the proposed method. The positioning error is compared with the engineering solution method, and it is proved that the proposed estimation method has the advantages of the high accuracy and good real-time performance.

scholarly journals High-Accuracy Real-Time Kinematic Positioning with Multiple Rover Receivers Sharing Common Clock

2021 ◽  
Vol 13 (4) ◽  
pp. 823
Author(s):  
Lin Zhao ◽  
Jiachang Jiang ◽  
Liang Li ◽  
Chun Jia ◽  
Jianhua Cheng
Keyword(s):  
Real Time ◽  
Ambiguity Resolution ◽  
Temporal Stability ◽  
Estimation Method ◽  
Satellite System ◽  
Integer Ambiguity ◽  
Dual Frequency ◽  
Kinematic Positioning ◽  
Real Time Kinematic ◽  
Satellite Visibility

Since the traditional real-time kinematic positioning method is limited by the reduced satellite visibility from the deprived navigational environments, we, therefore, propose an improved RTK method with multiple rover receivers sharing a common clock. The proposed method can enhance observational redundancy by blending the observations from each rover receiver together so that the model strength will be improved. Integer ambiguity resolution of the proposed method is challenged in the presence of several inter-receiver biases (IRB). The IRB including inter-receiver code bias (IRCB) and inter-receiver phase bias (IRPB) is calibrated by the pre-estimation method because of their temporal stability. Multiple BeiDou Navigation Satellite System (BDS) dual-frequency datasets are collected to test the proposed method. The experimental results have shown that the IRCB and IRPB under the common clock mode are sufficiently stable for the ambiguity resolution. Compared with the traditional method, the ambiguity resolution success rate and positioning accuracy of the proposed method can be improved by 19.5% and 46.4% in the restricted satellite visibility environments.

Research on the Distributed Characteristics of the Delay for Network Coding Based Real-Time Multicast in MANETs

2014 ◽  
Vol 530-531 ◽  
pp. 768-772
Author(s):  
Guo Ping Tan ◽  
Lin Feng Tan ◽  
Lei Cao ◽  
Mei Yan Ju
Keyword(s):  
Maximum Likelihood ◽  
Probability Distribution ◽  
Network Coding ◽  
Real Time ◽  
Lognormal Distribution ◽  
Ad Hoc ◽  
Estimation Method ◽  
Likelihood Estimation ◽  
Actual Distribution ◽  
Delay Distribution

For the study of the applications of partial network coding based real-time multicast protocol (PNCRM) in Mobile Ad hoc networks, the researches should be developed in the probability distribution of delay. In this paper, NS2 is used to obtain the delay of data packets through simulations. Because the delay does not obey the strict normal distribution, the maximum likelihood estimate method based on the lognormal distribution is used to process the data. Using MATLAB to obtain the actual distribution of the natural logarithm of delay, then drawing the delay distribution with the maximum likelihood estimation method based on the lognormal distribution, the conclusion that the distributions obtained by the above mentioned methods are basically consistent can be obtained. So the delay distribution of PNCRM meets the lognormal distribution and the characteristic of delay probability distribution can be estimated.

scholarly journals Experimental Verification of Real-Time Flow-Rate Estimations in a Tilting-Ladle-Type Automatic Pouring Machine

2021 ◽  
Vol 11 (15) ◽  
pp. 6701
Author(s):  
Yuta Sueki ◽  
Yoshiyuki Noda
Keyword(s):  
Real Time ◽  
Molten Metal ◽  
Flow Rate ◽  
Kalman Filters ◽  
Estimation Method ◽  
Estimation Methods ◽  
Liquid Volume ◽  
Model Parameters ◽  
Rate Estimation ◽  
Time Flow

This paper discusses a real-time flow-rate estimation method for a tilting-ladle-type automatic pouring machine used in the casting industry. In most pouring machines, molten metal is poured into a mold by tilting the ladle. Precise pouring is required to improve productivity and ensure a safe pouring process. To achieve precise pouring, it is important to control the flow rate of the liquid outflow from the ladle. However, due to the high temperature of molten metal, directly measuring the flow rate to devise flow-rate feedback control is difficult. To solve this problem, specific flow-rate estimation methods have been developed. In the previous study by present authors, a simplified flow-rate estimation method was proposed, in which Kalman filters were decentralized to motor systems and the pouring process for implementing into the industrial controller of an automatic pouring machine used a complicatedly shaped ladle. The effectiveness of this flow rate estimation was verified in the experiment with the ideal condition. In the present study, the appropriateness of the real-time flow-rate estimation by decentralization of Kalman filters is verified by comparing it with two other types of existing real-time flow-rate estimations, i.e., time derivatives of the weight of the outflow liquid measured by the load cell and the liquid volume in the ladle measured by a visible camera. We especially confirmed the estimation errors of the candidate real-time flow-rate estimations in the experiments with the uncertainty of the model parameters. These flow-rate estimation methods were applied to a laboratory-type automatic pouring machine to verify their performance.

Sign in / Sign up

Export Citation Format

Share Document