Introducing a Projection-Based Method to Compare Three Approaches Computing the Accumulation of Geometric Variations

2018 ◽  
Author(s):  
Vincent Delos ◽  
Santiago Arroyave-Tobón ◽  
Denis Teissandier
Keyword(s):  
Degrees Of Freedom ◽  
Mechanical Design ◽  
Geometric Constraints ◽  
Computational Time ◽  
Manufacturing Defects ◽  
Design Tolerance ◽  
Polyhedral Objects ◽  
The Difference ◽  
Bounded Sets ◽  
Accumulation Of Defects

In mechanical design, tolerance zones and contact gaps can be represented by sets of geometric constraints. For computing the accumulation of possible manufacturing defects, these sets have to be summed and/or intersected according to the assembly architecture. The advantage of this approach is its robustness for treating even over-constrained mechanisms i.e. mechanisms in which some degrees of freedom are suppressed in a redundant way. However, the sum of constraints, which must be computed when simulating the accumulation of defects in serial joints, is a very time-consuming operation. In this work, we compare three methods for summing sets of constraints using polyhedral objects. The difference between them lie in the way the degrees of freedom (DOFs) (or invariance) of joints and features are treated. The first method proposes to virtually limit the DOFs of the toleranced features and joints to turn the polyhedra into polytopes and avoid manipulating unbounded objects. Even though this approach enables to sum, it also introduces bounding or cap facets which increase the complexity of the operand sets. This complexity increases after each operation until becoming far too significant. The second method aims to face this problem by cleaning, after each sum, the calculated polytope to keep under control the effects of the propagation of the DOFs. The third method is new and based on the identification of the sub-space in which the projection of the operands are bounded sets. Calculating the sum in this sub-space allows reducing significantly the operands complexity and consequently the computational time. After presenting the geometric properties on which the approaches rely, we demonstrate them on an industrial case. Then we compare the computation times and deduce the equality of the results of all the methods.

On the Use of Quantum Thermal Bath in Unimolecular Fragmentation Simulations

2019 ◽  
Author(s):  
Riccardo Spezia ◽  
Hichem Dammak
Keyword(s):  
Degrees Of Freedom ◽  
Molecular Simulations ◽  
Zero Point ◽  
Thermal Bath ◽  
Unimolecular Dissociation ◽  
Point Energy ◽  
Rotational Degrees Of Freedom ◽  
The Difference ◽  
Nuclear Effects

<div> <div> <div> <p>In the present work we have investigated the possibility of using the Quantum Thermal Bath (QTB) method in molecular simulations of unimolecular dissociation processes. Notably, QTB is aimed in introducing quantum nuclear effects with a com- putational time which is basically the same as in newtonian simulations. At this end we have considered the model fragmentation of CH4 for which an analytical function is present in the literature. Moreover, based on the same model a microcanonical algorithm which monitor zero-point energy of products, and eventually modifies tra- jectories, was recently proposed. We have thus compared classical and quantum rate constant with these different models. QTB seems to correctly reproduce some quantum features, in particular the difference between classical and quantum activation energies, making it a promising method to study unimolecular fragmentation of much complex systems with molecular simulations. The role of QTB thermostat on rotational degrees of freedom is also analyzed and discussed. </p> </div> </div> </div>

scholarly journals A 4-DOF Upper Limb Exoskeleton for Physical Assistance: Design, Modeling, Control and Performance Evaluation

2021 ◽  
Vol 11 (13) ◽  
pp. 5865
Author(s):  
Muhammad Ahsan Gull ◽  
Mikkel Thoegersen ◽  
Stefan Hein Bengtson ◽  
Mostafa Mohammadi ◽  
Lotte N. S. Andreasen Struijk ◽  
...  
Keyword(s):  
Upper Limb ◽  
Tracking Control ◽  
Degrees Of Freedom ◽  
Control Method ◽  
Mechanical Design ◽  
Trajectory Tracking Control ◽  
Upper Limb Exoskeleton ◽  
And Performance ◽  
Physically Disabled People ◽  
Human Upper Limb

Wheelchair mounted upper limb exoskeletons offer an alternative way to support disabled individuals in their activities of daily living (ADL). Key challenges in exoskeleton technology include innovative mechanical design and implementation of a control method that can assure a safe and comfortable interaction between the human upper limb and exoskeleton. In this article, we present a mechanical design of a four degrees of freedom (DOF) wheelchair mounted upper limb exoskeleton. The design takes advantage of non-backdrivable mechanism that can hold the output position without energy consumption and provide assistance to the completely paralyzed users. Moreover, a PD-based trajectory tracking control is implemented to enhance the performance of human exoskeleton system for two different tasks. Preliminary results are provided to show the effectiveness and reliability of using the proposed design for physically disabled people.

scholarly journals Finite-Horizon Kinetic Energy Optimization of a Redundant Space Manipulator

2021 ◽  
Vol 11 (5) ◽  
pp. 2346
Author(s):  
Alessandro Tringali ◽  
Silvio Cocuzza
Keyword(s):  
Kinetic Energy ◽  
Real Time ◽  
Inverse Kinematics ◽  
Degrees Of Freedom ◽  
Computational Time ◽  
Redundant Manipulators ◽  
Space Robotics ◽  
Optimal Method ◽  
End Effector ◽  
Global Optimal

The minimization of energy consumption is of the utmost importance in space robotics. For redundant manipulators tracking a desired end-effector trajectory, most of the proposed solutions are based on locally optimal inverse kinematics methods. On the one hand, these methods are suitable for real-time implementation; nevertheless, on the other hand, they often provide solutions quite far from the globally optimal one and, moreover, are prone to singularities. In this paper, a novel inverse kinematics method for redundant manipulators is presented, which overcomes the above mentioned issues and is suitable for real-time implementation. The proposed method is based on the optimization of the kinetic energy integral on a limited subset of future end-effector path points, making the manipulator joints to move in the direction of minimum kinetic energy. The proposed method is tested by simulation of a three degrees of freedom (DOF) planar manipulator in a number of test cases, and its performance is compared to the classical pseudoinverse solution and to a global optimal method. The proposed method outperforms the pseudoinverse-based one and proves to be able to avoid singularities. Furthermore, it provides a solution very close to the global optimal one with a much lower computational time, which is compatible for real-time implementation.

scholarly journals A Modified KNN Algorithm for High-Performance Computing on FPGA of Real-Time m-QAM Demodulators

Electronics ◽  
2021 ◽  
Vol 10 (5) ◽  
pp. 627
Author(s):  
David Marquez-Viloria ◽  
Luis Castano-Londono ◽  
Neil Guerrero-Gonzalez
Keyword(s):  
Real Time ◽  
High Performance ◽  
Interference Mitigation ◽  
Parallel Implementation ◽  
Computational Time ◽  
Successful Implementation ◽  
Interchannel Interference ◽  
The Difference ◽  
High Level ◽  
Performance Computing

A methodology for scalable and concurrent real-time implementation of highly recurrent algorithms is presented and experimentally validated using the AWS-FPGA. This paper presents a parallel implementation of a KNN algorithm focused on the m-QAM demodulators using high-level synthesis for fast prototyping, parameterization, and scalability of the design. The proposed design shows the successful implementation of the KNN algorithm for interchannel interference mitigation in a 3 × 16 Gbaud 16-QAM Nyquist WDM system. Additionally, we present a modified version of the KNN algorithm in which comparisons among data symbols are reduced by identifying the closest neighbor using the rule of the 8-connected clusters used for image processing. Real-time implementation of the modified KNN on a Xilinx Virtex UltraScale+ VU9P AWS-FPGA board was compared with the results obtained in previous work using the same data from the same experimental setup but offline DSP using Matlab. The results show that the difference is negligible below FEC limit. Additionally, the modified KNN shows a reduction of operations from 43 percent to 75 percent, depending on the symbol’s position in the constellation, achieving a reduction 47.25% reduction in total computational time for 100 K input symbols processed on 20 parallel cores compared to the KNN algorithm.

Workspace, dexterity and dimensional optimization of microhexapod

2015 ◽  
Vol 35 (4) ◽  
pp. 341-347 ◽  
Author(s):  
E. Rouhani ◽  
M. J. Nategh
Keyword(s):  
Degrees Of Freedom ◽  
Optimization Problem ◽  
Screw Theory ◽  
Design Parameters ◽  
Dimensional Synthesis ◽  
Content Type ◽  
Workspace Analysis ◽  
The Difference ◽  
Flexure Joints ◽  
6 Degrees Of Freedom

Purpose – The purpose of this paper is to study the workspace and dexterity of a microhexapod which is a 6-degrees of freedom (DOF) parallel compliant manipulator, and also to investigate its dimensional synthesis to maximize the workspace and the global dexterity index at the same time. Microassembly is so essential in the current industry for manufacturing complicated structures. Most of the micromanipulators suffer from their restricted workspace because of using flexure joints compared to the conventional ones. In addition, the controllability of micromanipulators inside the whole workspace is very vital. Thus, it is very important to select the design parameters in a way that not only maximize the workspace but also its global dexterity index. Design/methodology/approach – Microassembly is so essential in the current industry for manufacturing complicated structures. Most of the micromanipulators suffer from their restricted workspace because of using flexure joints compared to the conventional ones. In addition, the controllability of micromanipulators inside the whole workspace is very vital. Thus, it is very important to select the design parameters in a way that not only maximize the workspace but also its global dexterity index. Findings – It has been shown that the proposed procedure for the workspace calculation can considerably speed the required calculations. The optimization results show that a converged-diverged configuration of pods and an increase in the difference between the moving and the stationary platforms’ radii cause the global dexterity index to increase and the workspace to decrease. Originality/value – The proposed algorithm for the workspace analysis is very important, especially when it is an objective function of an optimization problem based on the search method. In addition, using screw theory can simply construct the homogeneous Jacobian matrix. The proposed methodology can be used for any other micromanipulator.

scholarly journals Design of a 2DoF Ankle Exoskeleton with a Polycentric Structure and a Bi-Directional Tendon-Driven Actuator Controlled Using a PID Neural Network

Actuators ◽  
2021 ◽  
Vol 10 (1) ◽  
pp. 9
Author(s):  
Taehoon Lee ◽  
Inwoo Kim ◽  
Yoon Su Baek
Keyword(s):  
Neural Network ◽  
Degrees Of Freedom ◽  
Plantar Flexion ◽  
Length Change ◽  
Talocrural Joint ◽  
Lower Limb Exoskeleton ◽  
Exoskeleton Robot ◽  
The Difference ◽  
Ankle Exoskeleton ◽  
The Stability

Lower limb exoskeleton robots help with walking movements through mechanical force, by identifying the wearer’s walking intention. When the exoskeleton robot is lightweight and comfortable to wear, the stability of walking increases, and energy can be used efficiently. However, because it is difficult to implement the complex anatomical movements of the human body, most are designed simply. Due to this, misalignment between the human and robot movement causes the wearer to feel uncomfortable, and the stability of walking is reduced. In this paper, we developed a two degrees of freedom (2DoF) ankle exoskeleton robot with a subtalar joint and a talocrural joint, applying a four-bar linkage to realize the anatomical movement of a simple 1DoF structure mainly used for ankles. However, bidirectional tendon-driven actuators (BTDAs) do not consider the difference in a length change of both cables due to dorsiflexion (DF) and plantar flexion (PF) during walking, causing misalignment. To solve this problem, a BTDA was developed by considering the length change of both cables. Cable-driven actuators and exoskeleton robot systems create uncertainty. Accordingly, adaptive control was performed with a proportional-integral-differential neural network (PIDNN) controller to minimize system uncertainty.

Maximum Total Point Motion of Five Points Versus All Points in Assessing Tibial Baseplate Stability

2021 ◽  
Author(s):  
Abigail Niesen ◽  
Anna L Garverick ◽  
Maury Hull
Keyword(s):  
Degrees Of Freedom ◽  
Stability Limit ◽  
3D Models ◽  
Six Degrees Of Freedom ◽  
Percent Error ◽  
Model Based ◽  
Point Motion ◽  
The Mean ◽  
The Difference ◽  
Total Point

Abstract Maximum total point motion (MTPM), the point on a baseplate that migrates the most, has been used to assess the risk of tibial baseplate loosening using radiostereometric analysis (RSA). Two methods for determining MTPM for model-based RSA are to use either 5 points distributed around the perimeter of the baseplate or to use all points on the 3D model. The objectives were to quantify the mean difference in MTPM using 5 points vs. all points, compute the percent error relative to the 6-month stability limit for groups of patients, and to determine the dependency of differences in MTPM on baseplate size and shape. A dataset of 10,000 migration values was generated using the mean and standard deviation of migration in six degrees of freedom at 6 months from an RSA study. The dataset was used to simulate migration of 3D models (two baseplate shapes and two baseplate sizes) and calculate the difference in MTPM using 5 virtual points vs. all points and the percent error (i.e. difference in MTPM/stability limit) relative to the 6-month stability limit. The difference in MTPM was about 0.02 mm, or 4% percent relative to the 6-month stability limit, which is not clinically important. Furthermore, results were not affected by baseplate shape or size. Researchers can decide whether to use 5 points or all points when computing MTPM for model-based RSA. The authors recommend using 5 points to maintain consistency with marker-based RSA.

A Parallely Actuated Work Support Module for Reconfigurable Machining Systems

1998 ◽  
Author(s):  
Venkat Gopalakrishnan ◽  
Sridhar Kota
Keyword(s):  
Machine Tool ◽  
Machine Tools ◽  
Degrees Of Freedom ◽  
Mechanical Design ◽  
Performance Criteria ◽  
Machining Accuracy ◽  
Parallel Mechanisms ◽  
Element Analysis ◽  
Work Support ◽  
Reconfigurable Machining

Abstract In order to respond quickly to changes in market demands and the resulting product design changes, machine tool manufacturers must reduce the machine tool design lead time and machine set-up time. Reconfigurable Machine Tools (RMTs), assembled from machine modules such as spindles, slides and worktables are designed to be easily reconfigured to accommodate new machining requirements. The essential characteristics of RMTs are modularity, flexibility, convertibility and cost effectiveness. The goal of Reconfigurable Machining Systems (RMSs), composed of RMTs and other types of machines, is to provide exactly the capacity and functionality, exactly when needed. The scope of RMSs design includes mechanical hardware, control systems, process planning and tooling. One of the key challenges in the mechanical design of reconfigurable machine tools is to achieve the desired machining accuracy in all intended machine configurations. To meet this challenge we propose (a) to distribute the total number of degrees of freedom between the work-support and the tool and (b) employ parallely-actuated mechanisms for stiffness and ease of reconfigurability. In this paper we present a novel parallely-actuated work-support module as a part of an RMT. Following a brief summary of a few parallel mechanisms used in machine tool applications, this paper presents a three-degree-of-freedom work-support module designed to meet the machining requirements of specific features on a family of automotive cylinder heads. Inverse kinematics, dynamic and finite element analysis are performed to verify the performance criteria such as workspace envelope and rigidity. A prototype of the proposed module is also presented.

Integrated Redesign of Large-Scale Structures by Large Admissible Perturbations

2003 ◽  
Vol 125 (4) ◽  
pp. 234-241 ◽  
Author(s):  
Vincent Y. Blouin ◽  
Michael M. Bernitsas ◽  
Denby Morrison
Keyword(s):  
Degrees Of Freedom ◽  
Large Scale ◽  
Direct Method ◽  
Computational Effort ◽  
Forced Response ◽  
Response Amplitude ◽  
Computational Time ◽  
Performance Constraints ◽  
Large Admissible Perturbations ◽  
Design Selection

In structural redesign (inverse design), selection of the number and type of performance constraints is a major challenge. This issue is directly related to the computational effort and, most importantly, to the success of the optimization solver in finding a solution. These issues are the focus of this paper, which provides and discusses techniques that can help designers formulate a well-posed integrated complex redesign problem. LargE Admissible Perturbations (LEAP) is a general methodology, which solves redesign problems of complex structures with, among others, free vibration, static deformation, and forced response amplitude constraints. The existing algorithm, referred to as the Incremental Method is improved in this paper for problems with static and forced response amplitude constraints. This new algorithm, referred to as the Direct Method, offers comparable level of accuracy for less computational time and provides robustness in solving large-scale redesign problems in the presence of damping, nonstructural mass, and fluid-structure interaction effects. Common redesign problems include several natural frequency constraints and forced response amplitude constraints at various frequencies of excitation. Several locations on the structure and degrees of freedom can be constrained simultaneously. The designer must exercise judgment and physical intuition to limit the number of constraints and consequently the computational time. Strategies and guidelines are discussed. Such techniques are presented and applied to a 2,694 degree of freedom offshore tower.

scholarly journals Smoothed Particle Hydrodynamics Simulation of a Mariculture Platform under Waves

Water ◽  
2021 ◽  
Vol 13 (20) ◽  
pp. 2847
Author(s):  
Feng Zhang ◽  
Li Zhang ◽  
Yanshuang Xie ◽  
Zhiyuan Wang ◽  
Shaoping Shang
Keyword(s):  
Smoothed Particle Hydrodynamics ◽  
Graphics Processing Units ◽  
Degrees Of Freedom ◽  
High Tide ◽  
Theoretical Data ◽  
Emergency Evacuation ◽  
Water Levels ◽  
Computational Time ◽  
Particle Hydrodynamics ◽  
Smoothed Particle

This work investigates the dynamic behaviors of floating structures with moorings using open−source software for smoothed particle hydrodynamics. DualSPHysics permits us to use graphics processing units to recreate designs that include complex calculations at high resolution with reasonable computational time. A free damped oscillation was simulated, and its results were compared with theoretical data to validate the numerical model developed. The simulated three degrees of freedom (3−DoF) (surge, heave, and pitch) of a rectangular floating box have excellent consistency with experimental data. MoorDyn was coupled with DualSPHysics to include a mooring simulation. Finally, we modelled and simulated a real mariculture platform on the coast of China. We simulated the 3−DoF of this mariculture platform under a typical annual wave and a Typhoon Dujuan wave. The motion was light and gentle under the typical annual wave but vigorous under the Typhoon Dujuan wave. Experiments at different tidal water levels revealed an earlier motion response and smaller motion range during the high tide. The results reveal that DualSPHysics combined with MoorDyn is an adaptive scheme to simulate a coupled fluid–solid–mooring system. This work provides support to disaster warning, emergency evacuation, and proper engineering design.

Sign in / Sign up

Export Citation Format

Share Document