Noise Reduction in an Acoustic Cavity Using a Nonlinear Membrane Driven by an Electroacoustic Device

2017 ◽  
Author(s):  
Pierre-Yvon Bryk ◽  
Sergio Bellizzi ◽  
Renaud Côte
Keyword(s):  
Energy Transfer ◽  
Feedback Loop ◽  
Numerical Study ◽  
Front Face ◽  
Geometrical Properties ◽  
Acoustic Cavity ◽  
Nonlinear Absorber ◽  
Key Factor ◽  
Triggering Threshold ◽  
Nonlinear Membrane

In this paper an electro-Acoustic Nonlinear Absorber (ANLA) is described. It is composed of a baffled nonlinear membrane with its front face coupled to an acoustic cavity and the other one enclosed. The enclosure includes a feedback loop composed of a microphone and a loudspeaker that control the acoustic pressure seen by the rear face of the membrane. Due to the nonlinear geometrical properties of the membrane, the ANLA can synchronize it resonance with one of the resonances of the cavity. It allows to bring out the energy transfer toward the ANLA and thus to reduce pressure in the cavity. The feedback loop tunes the resonance frequency of the ANLA at low level, wich is a key factor for the triggering threshold of the targeted energy transfer. An numerical study of the efficiency of the ANLA to reduce noise in a cavity is presented including the influence of the feedback loop parameters.

scholarly journals Tuning Alginate Microparticle Size via Atomization of Non-Newtonian Fluids

Materials ◽  
2021 ◽  
Vol 14 (24) ◽  
pp. 7601
Author(s):  
Beatriz Arauzo ◽  
Álvaro González-Garcinuño ◽  
Antonio Tabernero ◽  
María Pilar Lobera ◽  
Jesús Santamaría ◽  
...  
Keyword(s):  
Particle Size ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Barium Chloride ◽  
Newtonian Fluids ◽  
Dimensionless Numbers ◽  
Experimental Conditions ◽  
New Approach ◽  
Hydrogel Beads ◽  
Key Factor

A new approach based on the atomization of non-Newtonian fluids has been proposed to produce microparticles for a potential inhalation route. In particular, different solutions of alginate were atomized on baths of different crosslinkers, piperazine and barium chloride, obtaining microparticles around 5 and 40 microns, respectively. These results were explained as a consequence of the different viscoelastic properties, since oscillatory analysis indicated that the formed hydrogel beads with barium chloride had a higher storage modulus (1000 Pa) than the piperazine ones (20 Pa). Pressure ratio (polymer solution-air) was identified as a key factor, and it should be from 0.85 to 1.00 to ensure a successful atomization, obtaining the smallest particle size at intermediate pressures. Finally, a numerical study based on dimensionless numbers was performed to predict particle size depending on the conditions. These results highlight that it is possible to control the microparticles size by modifying either the viscoelasticity of the hydrogel or the experimental conditions of atomization. Some experimental conditions (using piperazine) reduce the particle size up to 5 microns and therefore allow their use by aerosol inhalation.

scholarly journals Numerical Study Of The Targeted Energy Transfer Between The Euler-Bernoulli Beam And A Nonlinear Energy Sink

2021 ◽  
Author(s):  
Mohi U. Rahamat Ullah
Keyword(s):  
Energy Transfer ◽  
Primary Structure ◽  
Numerical Study ◽  
Element Model ◽  
Impact Excitation ◽  
Nonlinear Stiffness ◽  
Targeted Energy Transfer ◽  
Stiffness Property ◽  
Energy Sink ◽  
The Impact

Targeted energy transfer (TET) refers to the spatial transfer of energy between a primary structure of interest and isolated oscillators called the energy sink (ES). In this work, the primary structure of interest is a slender beam modeled by the Euler-Bernoulli theory, and the ES is a single-degree-of-freedom oscillator with either linear or cubic nonlinear stiffness property. The objective of this study is to characterize the TET and the effectiveness of ES under impact and periodic excitations. By using the scientific computation package, MATLAB, numerical simulations are carried out based on excitations of various strength and locations. Both time and frequency domain characterizations are used. For the impact excitation, the ES with the cubic nonlinear stiffness property is more superior to the linear oscillator in that larger percentage of the impact energy can be dissipated there. The main energy transfer was found to be due to a 3- to-1 frequency coupling between the first bending mode and the ES. For the periodic excitation, however, both linear and nonlinear ES exhibit generally poorer performance than the case with the impact excitation. Future works should focus on the frequency-energy relationship of the periodic solution of the underlying Hamiltonian, as well as using finite element model to verify the simulation results.

scholarly journals Effects of strain rate and CO2 on no formation in CH4/N2/O2 counter-flow diffusion flames

2018 ◽  
Vol 22 (Suppl. 2) ◽  
pp. 769-776
Author(s):  
Fei Ren ◽  
Longkai Xiang ◽  
Huaqiang Chu ◽  
Weiwei Han
Keyword(s):  
Strain Rate ◽  
Diffusion Flames ◽  
Numerical Study ◽  
Flame Temperature ◽  
Co2 Concentration ◽  
No Production ◽  
Counter Flow ◽  
Detailed Chemistry ◽  
No Formation ◽  
Key Factor

The reduction of nitrogen oxides in the high temperature flame is the key factor affecting the oxygen-enriched combustion performance. A numerical study using an OPPDIF code with detailed chemistry mechanism GRI 3.0 was carried out to focus on the effect of strain rate (25-130 s?1) and CO2 addition (0-0.59) on the oxidizer side on NO emission in CH4 / N2 / O2 counter-flow diffusion flame. The mole fraction profiles of flame structures, NO, NO2 and some selected radicals (H, O, OH) and the sensitivity of the dominant reactions contributing to NO formation in the counter-flow diffusion flames of CH4\/ N2 /O2 and CH4 / N2 / O2 / CO2 were obtained. The results indicated that the flame temperature and the amount of NO were reduced while the sensitivity of reactions to the prompt NO formation was gradually increased with the increasing strain rate. Furthermore, it is shown that with the increasing CO2 concentration in oxidizer, CO2 was directly involved in the reaction of NO consumption. The flame temperature and NO production were decreased dramatically and the mechanism of NO production was transformed from the thermal to prompt route.

scholarly journals Study of a Nonlinear Membrane Absorber Applied to 3D Acoustic Cavity for Low Frequency Broadband Noise Control

Materials ◽  
2019 ◽  
Vol 12 (7) ◽  
pp. 1138 ◽  
Author(s):  
Jianwang Shao ◽  
Tao Zeng ◽  
Xian Wu
Keyword(s):  
Degrees Of Freedom ◽  
Noise Control ◽  
Normal Modes ◽  
Low Frequency ◽  
Harmonic Balance Method ◽  
Nonlinear Normal Modes ◽  
Broadband Noise ◽  
Frequency Noise ◽  
Acoustic Cavity ◽  
Nonlinear Membrane

As a new approach to passive noise control in low frequency domain, the targeted energy transfer (TET) technique has been applied to the 3D fields of acoustics. The nonlinear membrane absorber based on the TET can reduce the low frequency noise inside the 3D acoustic cavity. The TET phenomenon inside the 3D acoustic cavity has firstly investigated by a two degrees-of-freedom (DOF) system, which is comprised by an acoustic mode and a nonlinear membrane without the pre-stress. In order to control the low frequency broadband noise inside 3D acoustic cavity and consider the influence of the pre-stress for the TET, a general model of the system with several acoustic modes of 3D acoustic cavity and one nonlinear membrane is built and studied in this paper. By using the harmonic balance method and the numerical method, the nonlinear normal modes and the forced responses are analyzed. Meanwhile, the influence of the pre-stress of the nonlinear membrane for the TET is investigated. The desired working zones of the nonlinear membrane absorber for the broadband noise are investigated. It can be helpful to design the nonlinear membrane according the dimension of 3D acoustic cavity to control the low frequency broadband noise.

Sign in / Sign up

Export Citation Format

Share Document