Linear and Non Linear Energy Harvesting From Bridge Vibrations

2016 ◽  
Author(s):  
Francesco Orfei ◽  
Helios Vocca ◽  
Luca Gammaitoni
Keyword(s):  
Time Series ◽  
Energy Harvesting ◽  
High Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Vibration Energy ◽  
Highway Bridge ◽  
Piezoelectric Energy ◽  
Non Linear ◽  
Bridge Vibrations

In this paper we analyze the performances of three different energy harvester configurations aimed at transforming vibration energy from a vehicle transited bridge. First of all we sampled the vibrations of a highway bridge in three different positions: at the entrance, in the middle and at the exit. Then, from the sampled time series, we reproduced the vibrations in the lab and tested the different harvesting configurations: low frequency linear piezoelectric energy harvester; high frequency linear piezoelectric energy harvester; non-linear bi-stable broadband piezoelectric energy harvester. The results are presented in terms of the RMS power converted. All the harvesters were built with the same piezoelectric material: composition and size were always the same.

scholarly journals Piezoelectric Energy Harvesting with an Ultrasonic Vibration Source

Actuators ◽  
2019 ◽  
Vol 8 (1) ◽  
pp. 8
Author(s):  
Tao Li ◽  
Pooi Lee
Keyword(s):  
Energy Harvesting ◽  
High Power ◽  
High Frequency ◽  
Energy Harvester ◽  
Impedance Matching ◽  
Low Frequency ◽  
Vibration Source ◽  
Piezoelectric Energy ◽  
Power Ultrasonic ◽  
Ultrasonic Cutting

A piezoelectric energy harvester was developed in this paper. It is actuated by the vibration leakage from the nodal position of a high-power ultrasonic cutting transducer. The harvester was excited at a low displacement amplitude (0.73 µmpp). However, its operation frequency is quite high and reaches the ultrasonic range (24.4 kHz). Compared with another low frequency harvester (66 Hz), both theoretical and experimental results proved that the advantages of this high frequency harvester include (i) high current generation capability (up to 20 mApp compared to 1.3 mApp of the 66 Hz transducer) and (ii) low impedance matching resistance (500 Ω in contrast to 50 kΩ of the 66 Hz transducer). This energy harvester can be applied either in sensing, or vibration controlling, or simply energy harvesting in a high-power ultrasonic system.

A novel low-frequency broadband piezoelectric energy harvester combined with a negative stiffness vibration isolator

2019 ◽  
Vol 30 (7) ◽  
pp. 1105-1114 ◽  
Author(s):  
Dongxing Cao ◽  
Xiangying Guo ◽  
Wenhua Hu
Keyword(s):  
Energy Harvesting ◽  
Energy Harvester ◽  
Low Frequency ◽  
Negative Stiffness ◽  
Vibration Energy ◽  
Vibration Isolator ◽  
Vibration Energy Harvester ◽  
Piezoelectric Energy ◽  
Piezoelectric Vibration Energy Harvester ◽  
Piezoelectric Vibration

The transformation of waste vibration energy into low-power electricity has been intensely researched over the last decade to enable self-sustained wireless electronic components. Many kinds of nonlinear oscillators have been explored by several research groups in an effort to enhance the frequency bandwidth of operation. The negative stiffness vibration isolator, as a kind of passive vibration isolator, has undergone extensive investigation because of its low-frequency isolator characteristics. In this article, a novel broadband piezoelectric vibration energy harvester, which can be used for low-frequency ambient mechanical energy harvesting, is designed, and its dynamic responses are analyzed based on the advantage of the negative stiffness vibration isolator. The multi-scale perturbation method is applied to solve the electromechanical equations of the piezoelectric vibration energy harvester and obtain approximate analytical solutions. Solutions based on the analytical method and numerical simulations reveal the characteristics of significant broadband performance. The effects of the various system parameters on the frequency responses and output voltage of the piezoelectric vibration energy harvester system are investigated in detail, and the vibration isolation ability is verified by experimental measurements. It was concluded that the proposed piezoelectric vibration energy harvester achieved broadband vibration energy harvesting in the low-frequency vibration range.

scholarly journals Topology Optimisation for High Frequency Vibration Energy Harvesting

2021 ◽  
Keyword(s):  
Energy Harvesting ◽  
High Frequency ◽  
Energy Harvester ◽  
Spring Steel ◽  
Condition Based Maintenance ◽  
Vibration Energy ◽  
Topology Optimisation ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
Maintenance Systems

Abstract. Topology optimisation has been used to design a piezoelectric energy harvester capable of harvesting the vibration present on a helicopter gearbox. The gearbox vibrations, with frequencies in the kilo-hertz range and having amplitudes of 10-100g (where g = 9.81 m/s2), are generated by gear-meshing within the transmission. These accelerations, large in amplitude and high in frequency, are ideal sources for vibration energy harvesting, with the harvested power potentially used to power autonomous condition-based-maintenance systems. This paper will discuss the first and simplest of the harvesters that were designed and manufactured, i.e. a 0.51 mm thick spring steel cantilever that uses a Pz27 piezoceramic transducer, which is sensitive to 1900 Hz gearbox vibrations and can produce 300 µW from a 2g host acceleration.

scholarly journals A Multi-Mode Broadband Vibration Energy Harvester Composed of Symmetrically Distributed U-Shaped Cantilever Beams

Micromachines ◽  
2021 ◽  
Vol 12 (2) ◽  
pp. 203
Author(s):  
Xiaohua Huang ◽  
Cheng Zhang ◽  
Keren Dai
Keyword(s):  
Energy Harvester ◽  
Low Frequency ◽  
Experimental Results ◽  
Vibration Energy ◽  
Cantilever Beams ◽  
Resonant Frequencies ◽  
Promising Alternative ◽  
Piezoelectric Energy ◽  
Straight Beam ◽  
Resonance Frequencies

Using the piezoelectric effect to harvest energy from surrounding vibrations is a promising alternative solution for powering small electronic devices such as wireless sensors and portable devices. A conventional piezoelectric energy harvester (PEH) can only efficiently collect energy within a small range around the resonance frequency. To realize broadband vibration energy harvesting, the idea of multiple-degrees-of-freedom (DOF) PEH to realize multiple resonant frequencies within a certain range has been recently proposed and some preliminary research has validated its feasibility. Therefore, this paper proposed a multi-DOF wideband PEH based on the frequency interval shortening mechanism to realize five resonance frequencies close enough to each other. The PEH consists of five tip masses, two U-shaped cantilever beams and a straight beam, and tuning of the resonance frequencies is realized by specific parameter design. The electrical characteristics of the PEH are analyzed by simulation and experiment, validating that the PEH can effectively expand the operating bandwidth and collect vibration energy in the low frequency. Experimental results show that the PEH has five low-frequency resonant frequencies, which are 13, 15, 18, 21 and 24 Hz; under the action of 0.5 g acceleration, the maximum output power is 52.2, 49.4, 61.3, 39.2 and 32.1 μW, respectively. In view of the difference between the simulation and the experimental results, this paper conducted an error analysis and revealed that the material parameters and parasitic capacitance are important factors that affect the simulation results. Based on the analysis, the simulation is improved for better agreement with experiments.

Broadband Rotational Energy Harvesting Using Micro Energy Harvester

2018 ◽  
Author(s):  
Jui-Ta Chien ◽  
Yung-Hsing Fu ◽  
Chao-Ting Chen ◽  
Shun-Chiu Lin ◽  
Yi-Chung Shu ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Low Frequency ◽  
Rotational Energy ◽  
Open Circuit ◽  
Maximum Output ◽  
Rotational Excitation ◽  
Rotating Speed ◽  
Piezoelectric Energy

This paper proposes a broadband rotational energy harvesting setup by using micro piezoelectric energy harvester (PEH). When driven in different rotating speed, the PEH can output relatively high power which exhibits the phenomenon of frequency up-conversion transforming the low frequency of rotation into the high frequency of resonant vibration. It aims to power self-powered devices used in the applications, like smart tires, smart bearings, and health monitoring sensors on rotational machines. Through the excitation of the rotary magnetic repulsion, the cantilever beam presents periodically damped oscillation. Under the rotational excitation, the maximum output voltage and power of PEH with optimal impedance is 28.2 Vpp and 663 μW, respectively. The output performance of the same energy harvester driven in ordinary vibrational based excitation is compared with rotational oscillation under open circuit condition. The maximum output voltage under 2.5g acceleration level of vibration is 27.54 Vpp while the peak output voltage of 36.5 Vpp in rotational excitation (in 265 rpm).

scholarly journals FINITE ELEMENT SIMULATION OF MEMS PIEZOELECTRIC ENERGY SCAVENGER BASED ON PZT THIN FILM

2019 ◽  
Vol 20 (1) ◽  
pp. 90-99
Author(s):  
Aliza Aini Md Ralib ◽  
Nur Wafa Asyiqin Zulfakher ◽  
Rosminazuin Ab Rahim ◽  
Nor Farahidah Za'bah ◽  
Noor Hazrin Hany Mohamad Hanif
Keyword(s):  
Thin Film ◽  
Energy Harvesting ◽  
Output Voltage ◽  
Energy Harvester ◽  
Maximum Output Power ◽  
Vibration Energy ◽  
Maximum Output ◽  
Vibration Energy Harvesting ◽  
Piezoelectric Energy ◽  
The World

Vibration energy harvesting has been progressively developed in the advancement of technology and widely used by a lot of researchers around the world. There is a very high demand for energy scavenging around the world due to it being cheaper in price, possibly miniaturized within a system, long lasting, and environmentally friendly. The conventional battery is hazardous to the environment and has a shorter operating lifespan. Therefore, ambient vibration energy serves as an alternative that can replace the battery because it can be integrated and compatible to micro-electromechanical systems. This paper presents the design and analysis of a MEMS piezoelectric energy harvester, which is a vibration energy harvesting type. The energy harvester was formed using Lead Zicronate Titanate (PZT-5A) as the piezoelectric thin film, silicon as the substrate layer and structural steel as the electrode layer. The resonance frequency will provide the maximum output power, maximum output voltage and maximum displacement of vibration. The operating mode also plays an important role to generate larger output voltage with less displacement of cantilever. Some designs also have been studied by varying height and length of piezoelectric materials. Hence, this project will demonstrate the simulation of a MEMS piezoelectric device for a low power electronic performance. Simulation results show PZT-5A piezoelectric energy with a length of 31 mm and height of 0.16 mm generates maximum output voltage of 7.435 V and maximum output power of 2.30 mW at the resonance frequency of 40 Hz. ABSTRAK: Penuaian tenaga getaran telah berkembang secara pesat dalam kemajuan teknologi dan telah digunakan secara meluas oleh ramai penyelidik di seluruh dunia. Terdapat permintaan yang sangat tinggi di seluruh dunia terhadap penuaian tenaga kerana harganya yang lebih murah, bersaiz kecil dalam satu sistem, tahan lama dan mesra alam. Manakala, bateri konvensional adalah berbahaya bagi alam sekitar dan mempunyai jangka hayat yang lebih pendek. Oleh itu, getaran tenaga dari persekitaran lebih sesuai sebagai alternatif kepada bateri kerana ia mudah diintegrasikan dan serasi dengan sistem mikroelektromekanikal. Kertas kerja ini  membentangkan reka bentuk dan analisis tenaga piezoelektrik MEMS iaitu salah satu jenis penuaian tenaga getaran. Penuai tenaga ini dibentuk menggunakan Lead Zicronate Titanate (PZT-5A) sebagai lapisan filem tipis piezoelektrik, silikon sebagai lapisan substrat dan keluli struktur sebagai lapisan elektrod. Frekuensi resonans akan memberikan hasil tenaga maksima, voltan tenaga maksima dan getaran jarak maksima. Mod pengendalian juga memainkan peranan penting bagi menghasilkan tenaga yang lebih besar. Reka bentuk yang mempunyai ketinggian dan panjang berlainan juga telah diuji dengan menggunakan bahan piezoelektrik yang sama. Oleh itu, projek ini akan menghasilkan simulasi piezoelektrik MEMS yang sesuai digunakan bagi alat elektronik berkuasa rendah. Hasil simulasi menunjukkan dengan panjang 31 mm dan ketinggian 0.16 mm, piezoelektrik PZT ini menghasilkan voltan maksima sebanyak 7.435 V dan tenaga output maksima 2.30 mW pada frekuensi resonans 40 Hz.

On Mathematical Modeling of Piezoelectric Energy Harvesters

2014 ◽  
Vol 953-954 ◽  
pp. 655-658 ◽  
Author(s):  
Guang Qing Shang ◽  
Hong Bing Wang ◽  
Chun Hua Sun
Keyword(s):  
Mathematical Modeling ◽  
Energy Harvesting ◽  
Energy Harvester ◽  
Vibration Energy ◽  
Piezoelectric Energy Harvesting ◽  
Vibration Energy Harvester ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Energy Harvesting System ◽  
Piezoelectric Vibration

Energy harvesting system has become one of important areas of ​​research and develops rapidly. How to improve the performance of the piezoelectric vibration energy harvester is a key issue in engineering applications. There are many literature on piezoelectric energy harvesting. The paper places focus on summarizing these literature of mathematical modeling of piezoelectric energy harvesting, ranging from the linear to nonlinear, from early a single mechanical degree to piezoaeroelastic problems.

Development of a tunable low-frequency vibration energy harvester and its application to a self-contained wireless fatigue crack detection sensor

2018 ◽  
Vol 18 (3) ◽  
pp. 920-933 ◽  
Author(s):  
Suyoung Yang ◽  
Sung-Youb Jung ◽  
Kiyoung Kim ◽  
Peipei Liu ◽  
Sangmin Lee ◽  
...  
Keyword(s):  
Fatigue Crack ◽  
Energy Harvesting ◽  
Crack Detection ◽  
Energy Harvester ◽  
Low Frequency ◽  
Vibration Energy ◽  
Low Frequency Vibration ◽  
Resonance Frequencies ◽  
Energy Harvesting System ◽  
Fatigue Crack Detection

In this study, a tunable electromagnetic energy harvesting system, consisting of an energy harvester and energy harvesting circuits, is developed for harnessing energy from low-frequency vibration (below 10 Hz) of a bridge, and the harvesting system is integrated with a wireless fatigue crack detection sensor. The uniqueness of the proposed energy harvesting system includes that (1) the resonance frequencies of the proposed energy harvester can be readily tuned to the resonance frequencies of a host structure, (2) an improved energy harvesting efficiency compared to other electromagnetic energy harvesters is achieved in low-frequency and vibration, and (3) high-efficiency energy harvesting circuits for rectification are developed. Furthermore, the developed energy harvesting system is integrated with an on-site wireless sensor deployed on Yeongjong Grand Bridge in South Korea for online fatigue crack detection. To the best knowledge of the authors, this is the very first study where a series of low-frequency vibration energy harvesting, rectification, and battery charging processes are demonstrated under a real field condition. The field test conducted on Yeongjong Grand Bridge, where fatigue cracks have become of a great concern, shows that the proposed energy harvester can generate a peak voltage of 2.27 V and a root mean square voltage of 0.21 V from 0.18-m/s2 root mean square acceleration at 3.05 Hz. It is estimated the proposed energy harvesting system can harness around 67.90 J for 3 weeks and an average power of 37.42 µW. The battery life of the wireless sensor is expected to extend from 1.5 to 2.2 years. The proposed energy harvesting circuits, composed of the AC–DC and boost-up converters, exhibit up to 50% battery charging efficiency when the voltage generated by the proposed energy harvester is 200 mV or higher. The proposed boost-up converter has a 100 times wider input power range than a conventional boost-up converter with a similar efficiency.

Heartbeat Energy Harvesting Using the Fan-Folded Piezoelectric Beam Geometry

2015 ◽  
Author(s):  
M. H. Ansari ◽  
M. Amin Karami
Keyword(s):  
Natural Frequency ◽  
Energy Harvester ◽  
Low Frequency ◽  
Mode Shapes ◽  
Vibration Energy ◽  
Vibration Energy Harvester ◽  
Mechanical Coupling ◽  
Energy Harvesters ◽  
Piezoelectric Energy ◽  
Piezoelectric Beam

A three dimensional piezoelectric vibration energy harvester is designed to generate electricity from heartbeat vibrations. The device consists of several bimorph piezoelectric beams stacked on top of each other. These horizontal bimorph beams are connected to each other by rigid vertical beams making a fan-folded geometry. One end of the design is clamped and the other end is free. One major problem in micro-scale piezoelectric energy harvesters is their high natural frequency. The same challenge is faced in development of a compact vibration energy harvester for the low frequency heartbeat vibrations. One way to decrease the natural frequency is to increase the length of the bimorph beam. This approach is not usually practical due to size limitations. By utilizing the fan-folded geometry, the natural frequency is decreased while the size constraints are observed. The required size limit of the energy harvester is 1 cm by 1 cm by 1 cm. In this paper, the natural frequencies and mode shapes of fan-folded energy harvesters are analytically derived. The electro-mechanical coupling has been included in the model for the piezoelectric beam. The design criteria for the device are discussed.

Optimizing the Electrical Power in an Energy Harvesting System

2015 ◽  
Vol 25 (12) ◽  
pp. 1550171 ◽  
Author(s):  
Mattia Coccolo ◽  
Grzegorz Litak ◽  
Jesús M. Seoane ◽  
Miguel A. F. Sanjuán
Keyword(s):  
Energy Harvesting ◽  
Kinetic Energy ◽  
High Frequency ◽  
Energy Harvester ◽  
Electrical Power ◽  
Low Frequency ◽  
Electrical Energy ◽  
Resonance Phenomenon ◽  
Vibrational Resonance ◽  
Energy Harvesting System

In this paper, we study the vibrational resonance (VR) phenomenon as a useful mechanism for energy harvesting purposes. A system, driven by a low frequency and a high frequency forcing, can give birth to the vibrational resonance phenomenon, when the two forcing amplitudes resonate and a maximum in amplitude is reached. We apply this idea to a bistable oscillator that can convert environmental kinetic energy into electrical energy, that is, an energy harvester. Normally, the VR phenomenon is studied in terms of the forcing amplitudes or of the frequencies, that are not always easy to adjust and change. Here, we study the VR generated by tuning another parameter that is possible to manipulate when the forcing values depend on the environmental conditions. We have investigated the dependence of the maximum response due to the VR for small and large variations in the forcing amplitudes and frequencies. Besides, we have plotted color coded figures in the space of the two forcing amplitudes, in which it is possible to appreciate different patterns in the electrical power generated by the system. These patterns provide useful information on the forcing amplitudes in order to produce the optimal electrical power.

Sign in / Sign up

Export Citation Format

Share Document