Fractional Order Model of Broadband Piezoelectric Energy Harvesters

2015 ◽  
Author(s):  
Dan Li ◽  
Junyi Cao ◽  
Shengxi Zhou ◽  
Yangquan Chen
Keyword(s):  
Energy Harvesting ◽  
Fractional Order ◽  
Piezoelectric Materials ◽  
Ambient Vibration ◽  
Piezoelectric Energy Harvesting ◽  
Order Model ◽  
Piezoelectric Energy ◽  
Fractional Order Model ◽  
Electromechanical Interaction ◽  
Environmental Vibration

This paper presents a factional model for broadband piezoelectric energy harvesting systems. Piezoelectric materials pay a significant role in harvesting ambient vibration energy. Due to their inherent characteristics and electromechanical interaction effect, piezoelectric energy harvesting exhibits the hysteresis characteristic under sweeping environmental vibration. Fractional order model of piezoelectric energy harvesting could capture the hysteresis characteristics. Simulation and experimental results show that fractional model of piezoelectric energy harvesting is more effective in describing the system dynamic.

scholarly journals A State-Of-The-Art Review of Car Suspension-Based Piezoelectric Energy Harvesting Systems

Energies ◽  
2020 ◽  
Vol 13 (9) ◽  
pp. 2336 ◽  
Author(s):  
Doaa Al-Yafeai ◽  
Tariq Darabseh ◽  
Abdel-Hamid I. Mourad
Keyword(s):  
Energy Harvesting ◽  
State Of The Art ◽  
Piezoelectric Materials ◽  
Clean Energy ◽  
Ambient Vibration ◽  
Dissipated Energy ◽  
Piezoelectric Energy Harvesting ◽  
Piezoelectric Energy ◽  
Harvesting Technique ◽  
Harvesting Systems

One of the most important techniques for energy harvesting is the clean energy collection from the ambient vibration. Piezoelectric energy harvesting systems became a hot topic in the literature and attracted most researchers. The reason behind this attraction is that piezoelectric materials are a simple structure and provide a higher power density among other mechanisms (electromagnetic and electrostatic). The aim of this manuscript is to succinctly review and present the state of the art of different existing vibrational applications utilizing piezoelectric energy harvesting technique. Meanwhile, the main concentration is harvesting energy from a vehicle suspension system. There is a significant amount of dissipated energy from the suspension dampers that is worthy of being harvested. Different mathematical car models with their experimental setup are presented, discussed, and compared. The piezoelectric material can be mounted in different locations such as suspension springs, dampers, and tires. The technique of implementing the harvester and the amount of power harvested from each location are analyzed. The evaluation of the electrical harvesting circuits and different storage devices for the harvested power are also discussed. The paper will also shed light on the variety of potential applications of the harvested energy.

Experimental Modal Analysis of Fractal-Inspired Multi-Frequency Piezoelectric Energy Converters

2011 ◽  
Author(s):  
D. Castagnetti
Keyword(s):  
Energy Harvesting ◽  
Piezoelectric Materials ◽  
Computational Simulation ◽  
Ambient Vibration ◽  
Thin Plates ◽  
Piezoelectric Energy Harvesting ◽  
Frequency Range ◽  
Piezoelectric Energy ◽  
Modal Response ◽  
Piezoelectric Converter

An important issue in the field of energy harvesting through piezoelectric materials is the design of simple and efficient structures which are multi-frequency in the ambient vibration range. This paper deals with the experimental assessment of four fractal-inspired multi-frequency structures for piezoelectric energy harvesting. These structures, thin plates of square shape, were proposed and numerically analyzed, with regard to their modal response, in a previous work by the author. The aim of this work is twofold. First, to assess the modal response of these structures through an experimental investigation. Second, to evaluate, through computational simulation, the performance of a piezoelectric converter prototype relying on one of these fractal-inspired structures. The four fractal-inspired structures are examined experimentally in the range between 0 and 100 Hz, both with regard to eigenfrequencies and eigenmodes. In the same frequency range are investigated the modal response and power output of a converter prototype.

scholarly journals Modeling of Piezoelectric Energy Harvesting from Freely Oscillating Cylinders in Water Flow

2014 ◽  
Vol 2014 ◽  
pp. 1-13 ◽  
Author(s):  
Min Zhang ◽  
YingZheng Liu ◽  
ZhaoMin Cao
Keyword(s):  
Energy Harvesting ◽  
Free Stream ◽  
Piezoelectric Materials ◽  
Load Resistance ◽  
Stream Velocity ◽  
Piezoelectric Energy Harvesting ◽  
Vibratory System ◽  
System Parameters ◽  
Piezoelectric Energy ◽  
Vortex Induced Vibrations

A concept of energy harvesting from vortex-induced vibrations of a rigid circular cylinder with two piezoelectric beams attached is investigated. The variations of the power levels with the free stream velocity are determined. A mathematical approach including the coupled cylinder motion and harvested voltage is presented. The effects of the load resistance, piezoelectric materials, and circuit combined on the natural frequency and damping of the vibratory system are determined by performing a linear analysis. The dynamic response of the cylinder and harvested energy are investigated. The results show that the harvested level in SS and SP&PS modes is the same with different values of load resistance. For four different system parameters, the results show that the bigger size of cylinder with PZT beams can obtain the higher harvested power.

Topology Optimization of Piezoelectric Energy Harvesting Devices Subjected to Stochastic Excitation

2010 ◽  
Author(s):  
Zheqi Lin ◽  
Hae Chang Gea ◽  
Shutian Liu
Keyword(s):  
Topology Optimization ◽  
Energy Harvesting ◽  
Electrical Energy ◽  
Ambient Vibration ◽  
Piezoelectric Energy Harvesting ◽  
The Past ◽  
Piezoelectric Energy ◽  
Random Responses ◽  
Pseudo Excitation ◽  
Energy Harvesting Devices

Converting ambient vibration energy into electrical energy using piezoelectric energy harvester has attracted much interest in the past decades. In this paper, topology optimization is applied to design the optimal layout of the piezoelectric energy harvesting devices. The objective function is defined as to maximize the energy harvesting performance over a range of ambient vibration frequencies. Pseudo excitation method (PEM) is applied to analyze structural stationary random responses. Sensitivity analysis is derived by the adjoint method. Numerical examples are presented to demonstrate the validity of the proposed approach.

Mechanistic Modeling and Economic Analysis of Piezoelectric Energy Harvesting Potential in Airport Pavements

2020 ◽  
Vol 2674 (11) ◽  
pp. 64-75
Author(s):  
Jingnan Zhao ◽  
Hao Wang
Keyword(s):  
Energy Harvesting ◽  
Economic Analysis ◽  
Power Output ◽  
Piezoelectric Materials ◽  
Mechanical Energy ◽  
Mechanistic Modeling ◽  
Piezoelectric Energy Harvesting ◽  
Levelized Cost Of Electricity ◽  
Near Surface ◽  
Piezoelectric Energy

This study investigated the feasibility of applying piezoelectric energy harvesting technology in airfield pavements through mechanistic modeling and economic analysis. The energy harvesting performance of piezoelectric transducers was evaluated based on mechanical energy induced by multi-wheel aircraft loading on flexible airfield pavements. A three-dimensional finite element model was used to estimate the stress pulse and magnitude under moving aircraft tire loading. A stack piezoelectric transducer design was used to estimate the power output of a piezoelectric harvester embedded at different locations and depths in the pavement. The aircraft load and speed were found to be vital factors affecting the power output, along with the installation depth and horizontal locations of the energy harvester. On the other hand, the installation of the energy module had a negligible influence on the horizontal tensile strains at the bottom of the asphalt layer and compressive strains on the top of the subgrade. However, the near-surface pavement strains increased when the edge ribs of the tire were loaded on the energy module. Feasibility analysis results showed that the calculated levelized cost of electricity was high in general, although it varies depending on the airport traffic levels and the service life of the energy module. With the development of piezoelectric materials and technology, further evaluation of energy harvesting applications at airports needs to be conducted.

Piezoelectric Energy Harvesting for Powering Micro Electromechanical Systems (MEMS)

2015 ◽  
Vol 8 (1) ◽  
Author(s):  
A. Majeed
Keyword(s):  
Energy Harvesting ◽  
Low Power ◽  
Piezoelectric Materials ◽  
Electrical Energy ◽  
Piezoelectric Energy Harvesting ◽  
Wireless Technology ◽  
Power Devices ◽  
Piezoelectric Energy ◽  
Technical Innovations ◽  
Low Power Electronics

Recent advancements in wireless technology and low power electronics such as micro electrome-chanical systems (MEMS), have created a surge of technical innovations in the eld of energy har-vesting. Piezoelectric materials, which operate on vibrations surrounding the system have becomehighly useful in terms of energy harvesting. Piezoelectricity is the ability to transform mechanicalstrain energy, mostly vibrations, to electrical energy, which can be used to power devices. This paperwill focus on energy harvesting by piezoelectricity and how it can be incorporated into various lowpower devices and explain the ability of piezoelectric materials to function as self-charging devicesthat can continuously supply power to a device and will not require any battery for future processes.

A Low-order Model for the Design of Piezoelectric Energy Harvesting Devices

2008 ◽  
Vol 20 (5) ◽  
pp. 495-504 ◽  
Author(s):  
Jeffrey L. Kauffman ◽  
George A. Lesieutre
Keyword(s):  
Energy Harvesting ◽  
Design Tool ◽  
Mode Shapes ◽  
Piezoelectric Energy Harvesting ◽  
Coupling Coefficients ◽  
Order Model ◽  
Power Sources ◽  
Piezoelectric Energy ◽  
Energy Harvesting Devices ◽  
Low Order

Piezoelectric energy harvesting devices are an attractive approach to providing remote wireless power sources. They operate by converting available vibration energy and storing it as electrical energy. Currently, most devices rely on mechanical excitation near their resonance frequency, so a low-order model which computes a few indicators of device performance is a critical design tool. Such a model, based on the assumed modes method, develops equations of motion to provide rapid computations of key device parameters, such as the natural frequencies, mode shapes, and electro-mechanical coupling coefficients. The model is validated with a comparison of its predictions and experimental data.

scholarly journals A Review on Piezoelectric Energy Harvesting: Materials, Methods, and Circuits

2019 ◽  
Vol 4 (1) ◽  
pp. 3-39 ◽  
Author(s):  
Shashank Priya ◽  
Hyun-Cheol Song ◽  
Yuan Zhou ◽  
Ronnie Varghese ◽  
Anuj Chopra ◽  
...  
Keyword(s):  
Energy Harvesting ◽  
Power Management ◽  
Energy Harvester ◽  
Piezoelectric Materials ◽  
Low Frequency ◽  
Small Scale ◽  
Piezoelectric Energy Harvesting ◽  
Wide Bandwidth ◽  
Piezoelectric Energy ◽  
Continuous Power

Abstract Piezoelectric microelectromechanical systems (PiezoMEMS) are attractive for developing next generation self-powered microsystems. PiezoMEMS promises to eliminate the costly assembly for microsensors/microsystems and provide various mechanisms for recharging the batteries, thereby, moving us closer towards batteryless wireless sensors systems and networks. In order to achieve practical implementation of this technology, a fully assembled energy harvester on the order of a quarter size dollar coin (diameter=24.26 mm, thickness=1.75 mm) should be able to generate about 100 μW continuous power from low frequency ambient vibrations (below 100 Hz). This paper reviews the state-of-the-art in microscale piezoelectric energy harvesting, summarizing key metrics such as power density and bandwidth of reported structures at low frequency input. This paper also describes the recent advancements in piezoelectric materials and resonator structures. Epitaxial growth and grain texturing of piezoelectric materials is being developed to achieve much higher energy conversion efficiency. For embedded medical systems, lead-free piezoelectric thin films are being developed and MEMS processes for these new classes of materials are being investigated. Non-linear resonating beams for wide bandwidth resonance are also reviewed as they would enable wide bandwidth and low frequency operation of energy harvesters. Particle/granule spray deposition techniques such as aerosol-deposition (AD) and granule spray in vacuum (GSV) are being matured to realize the meso-scale structures in a rapid manner. Another important element of an energy harvester is a power management circuit, which should maximize the net energy harvested. Towards this objective, it is essential for the power management circuit of a small-scale energy harvester to dissipate minimal power, and thus it requires special circuit design techniques and a simple maximum power point tracking scheme. Overall, the progress made by the research and industrial community has brought the energy harvesting technology closer to the practical applications in near future.

scholarly journals Energy harvesting with piezoelectric materials for IoT – Review

2019 ◽  
Vol 29 ◽  
pp. 03010
Author(s):  
Corina Covaci ◽  
Aurel Gontean
Keyword(s):  
Energy Harvesting ◽  
Mechanical Stress ◽  
Piezoelectric Materials ◽  
Piezoelectric Energy Harvesting ◽  
Portable Devices ◽  
Crystalline Materials ◽  
Smart Building ◽  
Piezoelectric Energy ◽  
Energy Consuming

The goal of this paper is to review up to date energy harvesting techniques, while focusing on energy harvesting with piezoelectric materials. A classification of various energy harvesting sources is provided in order to properly locate piezoelectricity. Piezoelectric energy harvesting uses the special material property that exists in many single crystalline materials: the direct piezoelectric effect. Those materials are generating electric potential when mechanical stress is applied. There are two types of mechanical stress suitable for piezoelectric energy harvesting: hitting and vibrating. The hitting method involves the direct transfer of energy to piezoelectric modules, so it generates more power than the vibrating method. This kind of energy harvesting is used to drive low energy consuming devices and is suitable for applications where replacement of battery or maintenance is unpractical, like sensors in the human body, for powering portable devices or it can be used for improvement of a smart building concept. If the piezoelectric transducers are placed in the floor of a crowded area or in shoes, it can theoretically generate 4.9 J/Step; therefore, this energy can be used to replace the chargeable batteries. This review is useful for a proper positioning of this type in the IoT broad context and mainly as an alternate energy source for wearables.

Sign in / Sign up

Export Citation Format

Share Document