Direct Geometry Processing for Tele-Fabrication

2012 ◽  
Author(s):  
Yong Chen ◽  
Kang Li ◽  
Xiaoping Qian
Keyword(s):  
Three Dimensional ◽  
Salient Feature ◽  
Physical Object ◽  
Geometry Processing ◽  
New Approach ◽  
B Splines ◽  
Geometric Processing ◽  
Scan Data ◽  
Manufacturing Technologies ◽  
Processing Techniques

This paper presents a new approach for tele-fabrication where a physical object is scanned in one location and fabricated in another location. This approach integrates three-dimensional (3D) scanning, geometric processing of scanned data, and additive manufacturing technologies. In this paper, we focus on a set of direct geometric processing techniques that enable the tele-fabrication. In this approach, 3D scan data is directly sliced into layer-wise contours. Sacrificial supports are generated directly from the contours and digital mask images of the objects and the supports for Stereolithography Apparatus (SLA) processes are then automatically generated. The salient feature of this approach is that it does not involve any intermediate geometric models such as STL, polygons or non-uniform rational B-splines that are otherwise commonly used in prevalent approaches. The experimental results on a set of objects fabricated on several SLA machines confirms the effectiveness of the approach in faithfully tele-fabricating physical objects.

Direct Geometry Processing for Telefabrication

2013 ◽  
Vol 13 (4) ◽  
Author(s):  
Yong Chen ◽  
Kang Li ◽  
Xiaoping Qian
Keyword(s):  
Additive Manufacturing ◽  
Three Dimensional ◽  
Salient Feature ◽  
Physical Object ◽  
Geometry Processing ◽  
New Approach ◽  
B Splines ◽  
Geometric Processing ◽  
Scan Data ◽  
Processing Techniques

This paper presents a new approach for telefabrication where a physical object is scanned in one location and fabricated in another location. This approach integrates three-dimensional (3D) scanning, geometric processing of scanned data, and additive manufacturing (AM) technologies. In this paper, we focus on a set of direct geometric processing techniques that enable the telefabrication. In this approach, 3D scan data are directly sliced into layer-wise contours. Sacrificial supports are generated directly from the contours and digital mask images of the objects and the supports for stereolithography apparatus (SLA) processes are then automatically generated. The salient feature of this approach is that it does not involve any intermediate geometric models such as STL, polygons, or nonuniform rational B-splines (NURBS) that are otherwise commonly used in prevalent approaches. The experimental results on a set of objects fabricated on several SLA machines confirm the effectiveness of the approach in faithfully telefabricating physical objects.

Three-Dimensional Structure of Rotavirus-Fab Complex

1990 ◽  
Vol 48 (1) ◽  
pp. 238-239
Author(s):  
B.V.V. Prasad ◽  
E. Marietta ◽  
J.W. Burns ◽  
M.K. Estes ◽  
W. Chiu
Keyword(s):  
Image Processing ◽  
Smooth Surface ◽  
Three Dimensional ◽  
Outer Shell ◽  
Dimensional Structure ◽  
Structural Studies ◽  
Cell Penetration ◽  
Electron Cryomicroscopy ◽  
Image Processing Techniques ◽  
Processing Techniques

Rotaviruses are spherical, double-shelled particles. They have been identified as a major cause of infantile gastroenteritis worldwide. In our earlier studies we determined the three-dimensional structures of double-and single-shelled simian rotavirus embedded in vitreous ice using electron cryomicroscopy and image processing techniques to a resolution of 40Å. A distinctive feature of the rotavirus structure is the presence of 132 large channels spanning across both the shells at all 5- and 6-coordinated positions of a T=13ℓ icosahedral lattice. The outer shell has 60 spikes emanating from its relatively smooth surface. The inner shell, in contrast, exhibits a bristly surface made of 260 morphological units at all local and strict 3-fold axes (Fig.l).The outer shell of rotavirus is made up of two proteins, VP4 and VP7. VP7, a glycoprotein and a neutralization antigen, is the major component. VP4 has been implicated in several important functions such as cell penetration, hemagglutination, neutralization and virulence. From our earlier studies we had proposed that the spikes correspond to VP4 and the rest of the surface is composed of VP7. Our recent structural studies, using the same techniques, with monoclonal antibodies specific to VP4 have established that surface spikes are made up of VP4.

scholarly journals Exploration of collagen cavitation based on peptide electrolysis

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Rui Zhai ◽  
Hui Chen ◽  
Zhihua Shan
Keyword(s):  
Structural Changes ◽  
Preparation Method ◽  
Supporting Electrolyte ◽  
Three Dimensional ◽  
Anode Region ◽  
New Approach ◽  
New Material ◽  
Animal Skin ◽  
Exchange Membrane ◽  
Material Preparation

AbstractElectrochemical modification of animal skin is a new material preparation method and new direction of research exploration. In this study, under the action of the electric field using NaCl as the supporting electrolyte, the effect of electrolysis on Glycyl-glycine(GlyGl), gelatin(Gel) and Three-dimensional rawhide collagen(3DC) were determined. The amino group of GlyGl is quickly eliminated within the anode region by electrolysis isolated by an anion exchange membrane. Using the same method, it was found that the molecular weight of Gel and the isoelectric point of the Gel decreased, and the viscosity and transparency of the Gel solution obviously changed. The electrolytic dissolution and structural changes of 3DC were further investigated. The results of TOC and TN showed that the organic matter in 3DC was dissolved by electrolysis, and the tissue cavitation was obvious. A new approach for the preparation of collagen-based multi-pore biomaterials by electrochemical method was explored.

scholarly journals A guideline for 3D printing terminology in biomedical research utilizing ISO/ASTM standards

2021 ◽  
Vol 7 (1) ◽  
Author(s):  
Amy E. Alexander ◽  
Nicole Wake ◽  
Leonid Chepelev ◽  
Philipp Brantner ◽  
Justin Ryan ◽  
...  
Keyword(s):  
3D Printing ◽  
Medical Literature ◽  
Three Dimensional ◽  
Physical Object ◽  
Medical Community ◽  
Layer By Layer ◽  
Digital File ◽  
Standardized Terminology ◽  
Standard Terms ◽  
The Impact

AbstractFirst patented in 1986, three-dimensional (3D) printing, also known as additive manufacturing or rapid prototyping, now encompasses a variety of distinct technology types where material is deposited, joined, or solidified layer by layer to create a physical object from a digital file. As 3D printing technologies continue to evolve, and as more manuscripts describing these technologies are published in the medical literature, it is imperative that standardized terminology for 3D printing is utilized. The purpose of this manuscript is to provide recommendations for standardized lexicons for 3D printing technologies described in the medical literature. For all 3D printing methods, standard general ISO/ASTM terms for 3D printing should be utilized. Additional, non-standard terms should be included to facilitate communication and reproducibility when the ISO/ASTM terms are insufficient in describing expository details. By aligning to these guidelines, the use of uniform terms for 3D printing and the associated technologies will lead to improved clarity and reproducibility of published work which will ultimately increase the impact of publications, facilitate quality improvement, and promote the dissemination and adoption of 3D printing in the medical community.

Three-Dimensional Computerized Anthropometry of the Nose: Landmark Representation Compared to Surface Analysis

2007 ◽  
Vol 44 (3) ◽  
pp. 278-285 ◽  
Author(s):  
Virgilio F. Ferrario ◽  
Fabrizio Mian ◽  
Redento Peretta ◽  
Riccardo Rosati ◽  
Chiarella Sforza
Keyword(s):  
Three Dimensional ◽  
Digital Data ◽  
Limits Of Agreement ◽  
B Splines ◽  
Surface Areas ◽  
Using Data ◽  
Difference Volume ◽  
T Values ◽  
Plaster Models ◽  
Plaster Casts

Objective: To compare three-dimensional nasal measurements directly made on subjects to those made on plaster casts, and nasal dimensions obtained with a surface-based approach to values obtained with a landmark representation. Methods: Soft-tissue nasal landmarks were directly digitized on 20 healthy adults. Stone casts of their noses were digitized and mathematically reconstructed using nonuniform rational B-splines (NURBS) curves. Linear distances, angles, volumes and surface areas were computed using facial landmarks and NURBS-reconstructed models (surface-based approach). Results: Measurements on the stone casts were somewhat smaller than values obtained directly from subjects (differences between −0.05 and −1.58 mm). Dahlberg's statistic ranged between 0.73 and 1.47 mm. Significant (p < .05) t values were found for 4 of 15 measurements. The surface-based approach gave values 3.5 (volumes) and 2.1 (surface area) times larger than those computed with the landmark-based method. The two values were significantly related (volume, r = 0.881; surface, r = 0.924; p < .001), the resulting equations estimated actual values well (mean difference, volume −0.01 mm3, SD 1.47, area 0.05 cm2, SD 1.44); limits of agreement between −2.89 and 2.87 mm3 (volume); −2.88 and 2.78 cm2 (area). Conclusions: Considering the characteristics of the two methods, and for practical purposes, nasal distances and angles obtained on plaster models were comparable to digital data obtained directly from subjects. Surface areas and volumes were best obtained using a surface-based approach, but could be estimated using data provided by the landmark representation.

scholarly journals A NEW APPROACH TO DYNAMIC FINITE-SIZE SCALING

2003 ◽  
Vol 14 (07) ◽  
pp. 945-954 ◽  
Author(s):  
MEHMET DİLAVER ◽  
SEMRA GÜNDÜÇ ◽  
MERAL AYDIN ◽  
YİĞİT GÜNDÜÇ
Keyword(s):  
Three Dimensional ◽  
Finite Size ◽  
Taylor Series Expansion ◽  
Scaling Behavior ◽  
Dynamic Scaling ◽  
Finite Size Scaling ◽  
New Approach ◽  
Size Scaling ◽  
Dynamic Exponent ◽  
Good Agreement

In this work we have considered the Taylor series expansion of the dynamic scaling relation of the magnetization with respect to small initial magnetization values in order to study the dynamic scaling behavior of two- and three-dimensional Ising models. We have used the literature values of the critical exponents and of the new dynamic exponent x0 to observe the dynamic finite-size scaling behavior of the time evolution of the magnetization during early stages of the Monte Carlo simulation. For the three-dimensional Ising model we have also presented that this method opens the possibility of calculating z and x0 separately. Our results show good agreement with the literature values. Measurements done on lattices with different sizes seem to give very good scaling.

scholarly journals Crystal Structure of an Aquabirnavirus Particle: Insights into Antigenic Diversity and Virulence Determinism

2009 ◽  
Vol 84 (4) ◽  
pp. 1792-1799 ◽  
Author(s):  
Fasséli Coulibaly ◽  
Christophe Chevalier ◽  
Bernard Delmas ◽  
Félix A. Rey
Keyword(s):  
Crystal Structure ◽  
Three Dimensional ◽  
Salient Feature ◽  
Infectious Pancreatic Necrosis Virus ◽  
Antigenic Determinants ◽  
Binding Motif ◽  
Icosahedral Symmetry ◽  
Fold Axis ◽  
Cell Internalization ◽  
Pancreatic Necrosis Virus

ABSTRACT Infectious pancreatic necrosis virus (IPNV), a pathogen of salmon and trout, imposes a severe toll on the aquaculture and sea farming industries. IPNV belongs to the Aquabirnavirus genus in the Birnaviridae family of bisegmented double-stranded RNA viruses. The virions are nonenveloped with a T=13l icosahedral capsid made by the coat protein VP2, the three-dimensional (3D) organization of which is known in detail for the family prototype, the infectious bursal disease virus (IBDV) of poultry. A salient feature of the birnavirus architecture is the presence of 260 trimeric spikes formed by VP2, projecting radially from the capsid. The spikes carry the principal antigenic sites as well as virulence and cell adaptation determinants. We report here the 3.4-Å resolution crystal structure of a subviral particle (SVP) of IPNV, containing 20 VP2 trimers organized with icosahedral symmetry. We show that, as expected, the SVPs have a very similar organization to the IBDV counterparts, with VP2 exhibiting the same overall 3D fold. However, the spikes are significantly different, displaying a more compact organization with tighter packing about the molecular 3-fold axis. Amino acids controlling virulence and cell culture adaptation cluster differently at the top of the spike, i.e., in a central bowl in IBDV and at the periphery in IPNV. In contrast, the spike base features an exposed groove, conserved across birnavirus genera, which contains an integrin-binding motif. Thus, in addition to revealing the viral antigenic determinants, the structure suggests that birnaviruses interact with different receptors for attachment and for cell internalization during entry.

Unique three-dimensional (3D) molecular array in dimethyl-DNTT crystals: a new approach to 3D organic semiconductors

2010 ◽  
Vol 1 (2) ◽  
pp. 179 ◽  
Author(s):  
Myeong Jin Kang ◽  
Tatsuya Yamamoto ◽  
Shoji Shinamura ◽  
Eigo Miyazaki ◽  
Kazuo Takimiya
Keyword(s):  
Organic Semiconductors ◽  
Three Dimensional ◽  
New Approach

scholarly journals An algorithm for delineating and extracting hillslopes and hillslope width functions from gridded elevation data

2011 ◽  
Vol 8 (5) ◽  
pp. 8865-8901
Author(s):  
P. Noel ◽  
A. N. Rousseau ◽  
C. Paniconi
Keyword(s):  
Three Dimensional ◽  
Rainfall Runoff ◽  
Dimensional Representation ◽  
New Approach ◽  
One Dimensional ◽  
Digital Elevation ◽  
Elevation Data ◽  
Average Profile ◽  
Elevation Model ◽  
Digital Elevation Model Resolution

Abstract. Subdivision of catchment into appropriate hydrological units is essential to represent rainfall-runoff processes in hydrological modelling. The commonest units used for this purpose are hillslopes (e.g. Fan and Bras, 1998; Troch et al., 2003). Hillslope width functions can therefore be utilised as one-dimensional representation of three-dimensional landscapes by introducing profile curvatures and plan shapes. An algorithm was developed to delineate and extract hillslopes and hillslope width functions by introducing a new approach to calculate an average profile curvature and plan shape. This allows the algorithm to be independent of digital elevation model resolution and to associate hillslopes to nine elementary landscapes according to Dikau (1989). This algortihm was tested on two flat and steep catchments of the province of Quebec, Canada. Results showed great area coverage for hillslope width function over individual hillslopes and entire watershed.

Sign in / Sign up

Export Citation Format

Share Document