Two-Degree-of-Freedom Decoupled Non-Redundant Cable-Loop-Driven Parallel Mechanism

2012 ◽  
Author(s):  
Hanwei Liu ◽  
Clément Gosselin ◽  
Thierry Laliberté
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Degree Of Freedom ◽  
The Other ◽  
Dynamic Equations ◽  
End Effector ◽  
Actuation Redundancy ◽  
Rigid Link ◽  
Force Closure ◽  
Two Degree Of Freedom

A novel two-degree-of-freedom cable-loop slider-driven parallel mechanism is introduced in this paper. The two degrees of freedom of the mechanism are decoupled and only two actuators are needed to control the motion. There are two cable loops for each direction of motion: one acts as the actuating loop while the other is the constraint loop. Due to the simple geometric design, the kinematic and static equations of the mechanism are very compact. The stiffness of the mechanism is also analyzed in the paper. It can be observed that the mechanism’s stiffness is much higher than the stiffness of the cables. Finally, the dynamic equations of the mechanism, including the compliance and the damping of the cables are obtained. The proposed mechanism’s workspace is essentially equal to its footprint and there are no singularities. The mechanism does not require the use of a rigid-link passive bridge and trolley (only cables are connected to the end-effector). Sliders located on the edges of the workspace are used and actuation redundancy is eliminated while providing force closure everywhere in the workspace.

Two-Degree-of-Freedom Decoupled Nonredundant Cable-Loop-Driven Parallel Mechanism

2013 ◽  
Vol 6 (1) ◽  
Author(s):  
Hanwei Liu ◽  
Clément Gosselin ◽  
Thierry Laliberté
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Degree Of Freedom ◽  
The Other ◽  
End Effector ◽  
Two Degrees Of Freedom ◽  
Actuation Redundancy ◽  
Rigid Link ◽  
Force Closure ◽  
Two Degree Of Freedom

A novel two-degree-of-freedom (DOF) cable-loop slider-driven parallel mechanism is introduced in this paper. The novelty of the mechanism lies in the fact that no passive rigid-link mechanism or springs are needed to support the end-effector (only cables are connected to the end-effector) while at the same time there is no actuation redundancy in the mechanism. Sliders located on the edges of the workspace are used and actuation redundancy is eliminated while providing force closure everywhere in the workspace. It is shown that the two degrees of freedom of the mechanism are decoupled and only two actuators are needed to control the motion. There are two cable loops for each direction of motion: one acts as the actuating loop while the other is the constraint loop. Due to the simple geometric design, the kinematic and static equations of the mechanism are very compact. The stiffness of the mechanism is also analyzed in the paper. It can be observed that the mechanism's stiffness is much higher than the stiffness of the cables. The proposed mechanism's workspace is essentially equal to its footprint and there are no singularities.

Reactionless Two-Degree-of-Freedom Planar Parallel Mechanism With Variable Payload

2009 ◽  
Author(s):  
Alexandre Lecours ◽  
Cle´ment Gosselin
Keyword(s):  
Dynamic Simulation ◽  
Parallel Mechanism ◽  
Reaction Force ◽  
Simulation Software ◽  
Degree Of Freedom ◽  
Dynamic Balancing ◽  
End Effector ◽  
Planar Mechanism ◽  
Two Degree Of Freedom ◽  
Arbitrary Trajectory

A reactionless mechanism is one which does not exert any reaction force or moment on its base at all times, for any arbitrary trajectory of the mechanism. This paper addresses the static and dynamic balancing of a two-degree-of-freedom parallel planar mechanism (five-bar mechanism). A simple and effective adaptive balancing method is presented that allows the mechanism to maintain the reactionless condition for a range of payloads. Important proofs concerning the balancing of five-bar mechanisms are also presented. The design of a real mechanism where parallelogram linkages are used to produce pure translations at the end-effector is also presented. Finally, using dynamic simulation software, it is shown that the mechanism is reactionless for arbitrarily chosen trajectories and for a variety of payloads.

A 7R-Based, Two Degrees of Freedom Robomech

2000 ◽  
Author(s):  
Ahmad A. Smaili
Keyword(s):  
Degrees Of Freedom ◽  
Parallel Architecture ◽  
Degree Of Freedom ◽  
Robot Arm ◽  
End Effector ◽  
Kinematic Constraints ◽  
Two Degrees Of Freedom ◽  
Synthesis Procedure ◽  
Two Degree Of Freedom

Abstract A robomech is a crossbreed of a mechanism and a robot arm. It has a parallel architecture equipped with more than one end effector to accomplish tasks that require the coordination of many functions. Robomechs with multi degrees of freedom that are based on the 4R and 5R chains have found their way into the literature. This article presents a new, two-degree of freedom robomech whose architecture is based on the 7R chain. The robomech is capable of performing two-function tasks. The features, kinematic constraints, and synthesis procedure of the robomech are outlined and an application example is given.

Reactionless Two-Degree-of-Freedom Planar Parallel Mechanism With Variable Payload

2010 ◽  
Vol 2 (4) ◽  
Author(s):  
Alexandre Lecours ◽  
Clément Gosselin
Keyword(s):  
Dynamic Simulation ◽  
Parallel Mechanism ◽  
Reaction Force ◽  
Simulation Software ◽  
Degree Of Freedom ◽  
Dynamic Balancing ◽  
End Effector ◽  
Planar Mechanism ◽  
Two Degree Of Freedom ◽  
Arbitrary Trajectory

A reactionless mechanism is one that does not exert any reaction force or moment on its base at all times, for any arbitrary trajectory of the mechanism. This paper addresses the static and dynamic balancing of a two-degree-of-freedom parallel planar mechanism (five-bar mechanism). A simple and effective adaptive balancing method is presented that allows the mechanism to maintain the reactionless condition for a range of payloads. Important proofs concerning the balancing of five-bar mechanisms are also presented. The design of a real mechanism where parallelogram linkages are used to produce pure translations at the end-effector is also presented. Finally, using dynamic simulation software, it is shown that the mechanism is reactionless for arbitrarily chosen trajectories and for a variety of payloads.

Vibration of Cams Having Two Degrees of Freedom

1964 ◽  
Vol 86 (4) ◽  
pp. 343-349 ◽  
Author(s):  
N. S. Eiss
Keyword(s):  
Analytical Solutions ◽  
Vibration Analysis ◽  
Vibration Amplitude ◽  
Degrees Of Freedom ◽  
Degree Of Freedom ◽  
The Other ◽  
Tabular Form ◽  
Two Degrees Of Freedom ◽  
Cam Follower ◽  
Two Degree Of Freedom

The vibration analysis of cam-follower systems is extended to models having two degrees of freedom. Two models are considered, one in which the cam support is rigid and the follower has two degrees of freedom, and the other, in which the cam support and follower each have one degree of freedom. Analytical solutions to six acceleration pulses are listed in tabular form. An example shows how tabulated solutions are added to give the displacement of a follower to a modified trapezoidal acceleration function. In another example, it is demonstrated how the parameters of a two-degree-of-freedom model are selected to give the minimum vibration amplitude.

Dynamics of a Two-DOF Parallel Pointing Mechanism

2005 ◽  
Author(s):  
Alessandro Cammarata ◽  
Rosario Sinatra
Keyword(s):  
Numerical Simulation ◽  
Parallel Mechanism ◽  
Inverse Dynamics ◽  
Kinematic Model ◽  
Degree Of Freedom ◽  
Numerical Examples ◽  
Proposed Model ◽  
Dynamic Analyses ◽  
Moving Platform ◽  
Two Degree Of Freedom

This paper presents kinematic and dynamic analyses of a two-degree-of-freedom pointing parallel mechanism. The mechanism consists of a moving platform, connected to a fixed platform by two legs of type PUS (prismatic-universal-spherical). At first a simplified kinematic model of the pointing mechanism is introduced. Based on this proposed model, the dynamics equations of the system using the Natural Orthogonal Complement method are developed. Numerical examples of the inverse dynamics results are presented by numerical simulation.

Force Capabilities of Two-Degree-of-Freedom Serial Robots Equipped With Passive Isotropic Force Limiters

2015 ◽  
Author(s):  
Meiying Zhang ◽  
Thierry Laliberté ◽  
Clément Gosselin
Keyword(s):  
Human Robot Interaction ◽  
Contact Forces ◽  
Degree Of Freedom ◽  
Practical Implementation ◽  
Robot Interaction ◽  
End Effector ◽  
Serial Robots ◽  
Serial Robot ◽  
Maximum Contact ◽  
Two Degree Of Freedom

This paper proposes the use of passive force and torque limiting devices to bound the maximum forces that can be applied at the end-effector or along the links of a robot, thereby ensuring the safety of human-robot interaction. Planar isotropic force limiting modules are proposed and used to analyze the force capabilities of a two-degree-of-freedom planar serial robot. The force capabilities at the end-effector are first analyzed. It is shown that, using isotropic force limiting modules, the performance to safety index remains excellent for all configurations of the robot. The maximum contact forces along the links of the robot are then analyzed. Force and torque limiters are distributed along the structure of the robot in order to ensure that the forces applied at any point of contact along the links are bounded. A power analysis is then presented in order to support the results. Finally, examples of mechanical designs of force/torque limiters are shown to illustrate a possible practical implementation of the concept.

Seven-Position Synthesis of a Spatial Eight-Bar Linkage by Constraining a TRS Serial Chain

2009 ◽  
Author(s):  
Gim Song Soh ◽  
J. Michael McCarthy
Keyword(s):  
Degree Of Freedom ◽  
Upper Arm ◽  
End Effector ◽  
Serial Chain ◽  
Position Synthesis ◽  
Two Degree Of Freedom ◽  
Puma Robot

In this paper, we use seven-position synthesis to add four TS constraints to a TRS serial chain robot and obtain a two degree-of-freedom spatial eight-bar linkage. The TRS chain is an elbow manipulator, similar to a PUMA robot. We synthesize a TS dyad to connect the base of the robot to its forearm, and then we synthesize three TS dyads that connect the upper arm of the robot to its end-effector. The result is a two degree-of-freedom spatial eight-bar linkage that moves through seven prescribed positions. It consists of a TRST loop supporting a 3TS-RS platform, which we denote as a TS-TRS-3TS spatial linkage. We formulate and solve the design equations for the TS dyads, and analyze the resulting eight-bar linkage. An example demonstrates our results.

Experimental Validation of the Kinematics of a 3PRS Compliant Mechanism for Micromilling

2015 ◽  
Author(s):  
Antonio Ruiz ◽  
Francisco Campa Gomez ◽  
Constantino Roldan-Paraponiaris ◽  
Oscar Altuzarra
Keyword(s):  
Parallel Mechanism ◽  
Degrees Of Freedom ◽  
Experimental Validation ◽  
Compliant Mechanism ◽  
Motion Controller ◽  
End Effector ◽  
Compliant Joints ◽  
Hybrid Manipulator ◽  
Compliant Parallel Mechanism ◽  
Actuated Joints

The present work deals with the development of a hybrid manipulator of 5 degrees of freedom for milling moulds for microlenses. The manipulator is based on a XY stage under a 3PRS compliant parallel mechanism. The mechanism takes advantage of the compliant joints to achieve higher repetitiveness, smoother motion and a higher bandwidth, due to the high precision demanded from the process, under 0.1 micrometers. This work is focused on the kinematics of the compliant stage of the hybrid manipulator. First, an analysis of the workspace required for the milling of a single mould has been performed, calculating the displacements required in X, Y, Z axis as well as two relative rotations between the tool and the workpiece from a programmed toolpath. Then, the 3PRS compliant parallel mechanism has been designed using FEM with the objective of being stiff enough to support the cutting forces from the micromilling, but flexible enough in the revolution and spherical compliant joints to provide the displacements needed. Finally, a prototype of the 3PRS compliant mechanism has been built, implementing a motion controller to perform translations in Z direction and two rotations. The resulting displacements in the end effector and the actuated joints have been measured and compared with the FEM calculations and with the rigid body kinematics of the 3PRS.

Research on a Variable Degree of Freedom Luffing Mechanism, Part I

2013 ◽  
Vol 842 ◽  
pp. 433-438
Author(s):  
Xiao Guang Yao ◽  
Yong Bao Feng ◽  
Xiao Song Guo ◽  
Chang Lin Ma
Keyword(s):  
Degrees Of Freedom ◽  
Work Conditions ◽  
Degree Of Freedom ◽  
Dynamic Equations ◽  
Variable Degree ◽  
Analytic Model ◽  
Body System ◽  
Electric Control ◽  
Engineering Requirement ◽  
Relationship Of

According to the special engineering requirement, a novel luffing mechanism with variable degree of freedom is presented in this study. The mechanism is assumed to be an ideal rigid body system and the degrees of freedom in different work conditions are calculated. Then the kinematic equations of mechanism are obtained by the geometrical and motional relationship of the components; meanwhile, the dynamic equations of mechanism are deduced by the Newton's mechanical law. The analytic model can be employed for the calculation and analysis of the mechanism features; furthermore, it can be used for the design of hydraulic and electric control system.

Sign in / Sign up

Export Citation Format

Share Document