Free and Forced Response of a Piecewise Linear 2-DOF System: Analysis and Experiments

2009 ◽  
Author(s):  
Fabrizio Vestroni ◽  
Paolo Casini ◽  
Oliviero Giannini
Keyword(s):  
System Analysis ◽  
Piecewise Linear ◽  
Damage Parameter ◽  
Forced Response ◽  
Experimental Investigations ◽  
Restoring Force ◽  
Proposed Model ◽  
Wide Range ◽  
Set Up ◽  
Theoretical Analyses

The present paper analyzes the free and forced dynamics of a 2-DOF mechanical system with piecewise linear restoring force, by means of analytical/numerical and experimental investigations. This oscillator is roughly representative of an asymmetrically cracked cantilever beam vibrating in bending and hence exhibiting a bilinear stiffness, depending on whether the crack is open or closed. A parametric analysis of the NNMs has been performed for a wide range of the damage parameter: the influence of damage on the nonlinear frequencies has been investigated and bifurcations characterized by the onset of superabundant modes with or without internal resonance, have been revealed. The dynamic behavior of the system under harmonic base excitation has been numerically investigated assuming both low and high damping. It has been found that the NNMs of the free motion play a key role in the system forced response. Finally, a test set-up has then been built to investigate the validity of the proposed model for technical applications: the experimental measurements qualitatively and quantitatively capture the basic bifurcation scenarios anticipated by the model while a strong robustness of the phenomena pointed out by the theoretical analyses has been revealed in the experiments.

Is relaxation an active process?

1949 ◽  
Vol 136 (884) ◽  
pp. 420-435 ◽  
Keyword(s):  
Latent Period ◽  
Mechanical Damage ◽  
The Body ◽  
Active Process ◽  
Restoring Force ◽  
Resting Tension ◽  
Internal Structures ◽  
Wide Range ◽  
Muscle Heat Production ◽  
Set Up

Measurements of muscle heat production had indicated that relaxation is not an active process. Experiments to test this conclusion were made in two ways: ( a ) by measuring the mechanical latent period in isometric contractions over a wide range of lengths down to less than half the natural length in the body, and ( b ) by determining the relation between resting tension and length down to lengths at which the muscle became slack. In a muscle under its resting tension alone the latent period after a shock remains nearly constant over a wide range of lengths. This range is extended by previous stimulation. If active relaxation occurred the latent period would be greatly increased. A resting muscle exerts measurable tension down to 60 to 75% of its natural length in the body. By previous stimulation at a shorter length the range of lengths within which measurable tension is exerted is increased. In a muscle under zero external load lengthening occurs after contraction only from very short lengths. It is attributed to an elastic restoring force set up by the lateral expansion of the fibres. The ' δ -state’ described by Ramsey & Street in isolated fibres allowed to shorten too much is discussed. It may be due to mechanical damage to internal structures normally reinforcing the sarcolemma against expansion. The nature of the contractile linkages in muscle is considered.

A symmetrically piecewise linear oscillator: Design and measurement

1999 ◽  
Vol 213 (3) ◽  
pp. 241-249 ◽  
Author(s):  
V. W. T. Sin ◽  
M Wiercigroch
Keyword(s):  
Mathematical Model ◽  
Piecewise Linear ◽  
Viscous Damping ◽  
Cantilever Beams ◽  
Piecewise Linear System ◽  
Leaf Springs ◽  
Design Choice ◽  
Wide Range ◽  
Set Up ◽  
The Mathematical Model

A simple piecewise linear system with symmetrical flexible constraints was designed and manufactured to carry out a wide range of experimental dynamic analysis and ultimately to validate piecewise models. The design choice was based on the following criteria: accuracy in representing the mathematical model, manufacturing simplicity, flexibility in terms of parameter changes and cost effectiveness. The system consists of a block mass attached to two leaf springs, the stiffness of which can easily be varied by changing their length. The secondary stiffness in the form of cantilever beams can be widely varied in the same way. The clearance between the mass and secondary springs can also be varied by adjusting the screws at the ends of the beams. A variable pneumatic damper is mounted on the upper surface of the mass and provides a means of changing the viscous damping coefficient. The experimental set-up, calibration procedures and typical results are discussed.

Settlers or Movers? The Temporality of Past Migrations, Political Inaction and its Consequences, 1945–1985

2018 ◽  
Author(s):  
Jozefien De Bock
Keyword(s):  
Temporary Workers ◽  
Guest Workers ◽  
Temporary Migration ◽  
Wide Range ◽  
Settler Societies ◽  
Future Policy ◽  
Set Up ◽  
Legal Frameworks ◽  
Temporary Migrants ◽  
Multicultural Policies

Historically, those societies that have the longest tradition in multicultural policies are settler societies. The question of how to deal with temporary migrants has only recently aroused their interest. In Europe, temporary migration programmes have a much longer history. In the period after WWII, a wide range of legal frameworks were set up to import temporary workers, who came to be known as guest workers. In the end, many of these ‘guests’ settled in Europe permanently. Their presence lay at the basis of European multicultural policies. However, when these policies were drafted, the former mobility of guest workers had been forgotten. This chapter will focus on this mobility of initially temporary workers, comparing the period of economic growth 1945-1974 with the years after the 1974 economic crisis. Further, it will look at the kind of policies that were developed towards guest workers in the era before multiculturalism. This way, it shows how their consideration as temporary residents had far-reaching consequences for the immigrants, their descendants and the receiving societies involved. The chapter will finish by suggesting a number of lessons from the past. If the mobility-gap between guest workers and present-day migrants is not as big as generally assumed, then the consequences of previous neglect should serve as a warning for future policy making.

ORAL HISTORY SOURCES AS LEARNING MATERIALS: A CASE STUDY OF THE NATIONAL UNIVERSITY OF SCIENCE AND TECHNOLOGY

2016 ◽  
Vol 3 (2) ◽  
pp. 82-93
Author(s):  
Gugulethu Shamaine Nkala ◽  
Rodreck David
Keyword(s):  
Oral History ◽  
Learning Experience ◽  
Science And Technology ◽  
Group Discussion ◽  
Human Interaction ◽  
Learning Material ◽  
Wide Range ◽  
National Archives ◽  
National University ◽  
Set Up

Knowledge presented by Oral History (OH) is unique in that it shares the tacit perspective, thoughts, opinions and understanding of the interviewee in its primary form. While teachers, lecturers and other education specialists have at their disposal a wide range of primary, secondary and tertiary sources upon which to relate and share or impart knowledge, OH presents a rich source of information that can improve the learning and knowledge impartation experience. The uniqueness of OH is presented in the following advantages of its use: it allows one to learn about the perspectives of individuals who might not otherwise appear in the historical record; it allows one to compensate for the digital age; one can learn different kinds of information; it provides historical actors with an opportunity to tell their own stories in their own words; and it offers a rich opportunity for human interaction. This article discusses the placement of oral history in the classroom set-up by investigating its use as a source of learning material presented by the National Archives of Zimbabwe to students in the Department of Records and Archives Management at the National University of Science and Technology (NUST). Interviews and a group discussion were used to gather data from an archivist at the National Archives of Zimbabwe, lecturers and students in the Department of Records and Archives Management at NUST, respectively. These groups were approached on the usability, uniqueness and other characteristics that support this type of knowledge about OH in a tertiary learning experience. The findings indicate several qualities that reflect the richness of OH as a teaching source material in a classroom set-up. It further points to weak areas that may be addressed where the source is considered a viable strategy for knowledge sharing and learning. The researchers present a possible model that can be used to champion the use of this rich knowledge source in classroom education at this university and in similar set-ups. 

Nanofiltration of endocrine disrupting compounds

2003 ◽  
Vol 3 (5-6) ◽  
pp. 321-327 ◽  
Author(s):  
M. Gallenkemper ◽  
T. Wintgens ◽  
T. Melin
Keyword(s):  
Wastewater Treatment ◽  
Municipal Wastewater ◽  
Wastewater Treatment Plants ◽  
Endocrine Disrupting Compounds ◽  
Municipal Wastewater Treatment ◽  
Water And Wastewater Treatment ◽  
Wide Range ◽  
Endocrine Disrupting ◽  
Municipal Wastewater Treatment Plants ◽  
Set Up

Endocrine disrupting compounds can affect the hormone system in organisms. A wide range of endocrine disrupters were found in sewage and effluents of municipal wastewater treatment plants. Toxicological evaluations indicate that conventional wastewater treatment plants are not able to remove these substances sufficiently before disposing effluent into the environment. Membrane technology, which is proving to be an effective barrier to these substances, is the subject of this research. Nanofiltration provides high quality permeates in water and wastewater treatment. Eleven different nanofiltration membranes were tested in the laboratory set-up. The observed retention for nonylphenol (NP) and bisphenol A (BPA) ranged between 70% and 100%. The contact angle is an indicator for the hydrophobicity of a membrane, whose influence on the permeability and retention of NP was evident. The retention of BPA was found to be inversely proportional to the membrane permeability.

scholarly journals Low-Energy Electron Damage to Condensed-Phase DNA and Its Constituents

2021 ◽  
Vol 22 (15) ◽  
pp. 7879
Author(s):  
Yingxia Gao ◽  
Yi Zheng ◽  
Léon Sanche
Keyword(s):  
Condensed Phase ◽  
Genetic Material ◽  
High Energy ◽  
Dna Lesions ◽  
Low Energy ◽  
Experimental Investigations ◽  
Experimental Conditions ◽  
Strand Breaks ◽  
Sequence Of Events ◽  
Wide Range

The complex physical and chemical reactions between the large number of low-energy (0–30 eV) electrons (LEEs) released by high energy radiation interacting with genetic material can lead to the formation of various DNA lesions such as crosslinks, single strand breaks, base modifications, and cleavage, as well as double strand breaks and other cluster damages. When crosslinks and cluster damages cannot be repaired by the cell, they can cause genetic loss of information, mutations, apoptosis, and promote genomic instability. Through the efforts of many research groups in the past two decades, the study of the interaction between LEEs and DNA under different experimental conditions has unveiled some of the main mechanisms responsible for these damages. In the present review, we focus on experimental investigations in the condensed phase that range from fundamental DNA constituents to oligonucleotides, synthetic duplex DNA, and bacterial (i.e., plasmid) DNA. These targets were irradiated either with LEEs from a monoenergetic-electron or photoelectron source, as sub-monolayer, monolayer, or multilayer films and within clusters or water solutions. Each type of experiment is briefly described, and the observed DNA damages are reported, along with the proposed mechanisms. Defining the role of LEEs within the sequence of events leading to radiobiological lesions contributes to our understanding of the action of radiation on living organisms, over a wide range of initial radiation energies. Applications of the interaction of LEEs with DNA to radiotherapy are briefly summarized.

scholarly journals Low Power Cusped Field Thruster Developed for the Space-Borne Gravitational Wave Detection Mission in China

2021 ◽  
Vol 11 (14) ◽  
pp. 6549
Author(s):  
Hui Liu ◽  
Ming Zeng ◽  
Xiang Niu ◽  
Hongyan Huang ◽  
Daren Yu
Keyword(s):  
Low Power ◽  
Gravitational Wave ◽  
Attitude Control ◽  
High Efficiency ◽  
Experimental Investigations ◽  
Attitude Control System ◽  
Gravitational Wave Detection ◽  
Wave Detection ◽  
Wide Range ◽  
Institute Of Technology

The microthruster is the crucial device of the drag-free attitude control system, essential for the space-borne gravitational wave detection mission. The cusped field thruster (also called the High Efficiency Multistage Plasma Thruster) becomes one of the candidate thrusters for the mission due to its low complexity and potential long life over a wide range of thrust. However, the prescribed minimum of thrust and thrust noise are considerable obstacles to downscaling works on cusped field thrusters. This article reviews the development of the low power cusped field thruster at the Harbin Institute of Technology since 2012, including the design of prototypes, experimental investigations and simulation studies. Progress has been made on the downscaling of cusped field thrusters, and a new concept of microwave discharge cusped field thruster has been introduced.

scholarly journals A System-Agnostic, Adaptable and Extensible Animal Support Cradle System for Cardio-Respiratory-Synchronised, and Other, Multi-Modal Imaging of Small Animals

Tomography ◽  
2021 ◽  
Vol 7 (1) ◽  
pp. 39-54
Author(s):  
Veerle Kersemans ◽  
Stuart Gilchrist ◽  
Philip Danny Allen ◽  
Sheena Wallington ◽  
Paul Kinchesh ◽  
...  
Keyword(s):  
Scientific Data ◽  
Cardiac Monitoring ◽  
Small Animals ◽  
Maintenance System ◽  
Wide Range ◽  
Set Up ◽  
Animal Handling ◽  
Imaging Performance ◽  
Significant Effort

Standardisation of animal handling procedures for a wide range of preclinical imaging scanners will improve imaging performance and reproducibility of scientific data. Whilst there has been significant effort in defining how well scanners should operate and how in vivo experimentation should be practised, there is little detail on how to achieve optimal scanner performance with best practices in animal welfare. Here, we describe a system-agnostic, adaptable and extensible animal support cradle system for cardio-respiratory-synchronised, and other, multi-modal imaging of small animals. The animal support cradle can be adapted on a per application basis and features integrated tubing for anaesthetic and tracer delivery, an electrically driven rectal temperature maintenance system and respiratory and cardiac monitoring. Through a combination of careful material and device selection, we have described an approach that allows animals to be transferred whilst under general anaesthesia between any of the tomographic scanners we currently or have previously operated. The set-up is minimally invasive, cheap and easy to implement and for multi-modal, multi-vendor imaging of small animals.

scholarly journals Prediction of Pest Insect Appearance Using Sensors and Machine Learning

Sensors ◽  
2021 ◽  
Vol 21 (14) ◽  
pp. 4846
Author(s):  
Dušan Marković ◽  
Dejan Vujičić ◽  
Snežana Tanasković ◽  
Borislav Đorđević ◽  
Siniša Ranđić ◽  
...  
Keyword(s):  
Machine Learning ◽  
Relative Humidity ◽  
Weather Conditions ◽  
Daily Basis ◽  
Machine Learning Algorithms ◽  
Lower Percentage ◽  
Timely Manner ◽  
Proposed Model ◽  
Set Up ◽  
Accuracy Of Prediction

The appearance of pest insects can lead to a loss in yield if farmers do not respond in a timely manner to suppress their spread. Occurrences and numbers of insects can be monitored through insect traps, which include their permanent touring and checking of their condition. Another more efficient way is to set up sensor devices with a camera at the traps that will photograph the traps and forward the images to the Internet, where the pest insect’s appearance will be predicted by image analysis. Weather conditions, temperature and relative humidity are the parameters that affect the appearance of some pests, such as Helicoverpa armigera. This paper presents a model of machine learning that can predict the appearance of insects during a season on a daily basis, taking into account the air temperature and relative humidity. Several machine learning algorithms for classification were applied and their accuracy for the prediction of insect occurrence was presented (up to 76.5%). Since the data used for testing were given in chronological order according to the days when the measurement was performed, the existing model was expanded to take into account the periods of three and five days. The extended method showed better accuracy of prediction and a lower percentage of false detections. In the case of a period of five days, the accuracy of the affected detections was 86.3%, while the percentage of false detections was 11%. The proposed model of machine learning can help farmers to detect the occurrence of pests and save the time and resources needed to check the fields.

scholarly journals LED Rail Signals: Full Hardware Realization of Apparatus with Independent Intensity by Temperature Changes

Electronics ◽  
2021 ◽  
Vol 10 (11) ◽  
pp. 1291
Author(s):  
Giuseppe Schirripa Schirripa Spagnolo ◽  
Fabio Leccese
Keyword(s):  
Temperature Sensor ◽  
Energy Efficient ◽  
Light Emitting Diode ◽  
Junction Temperature ◽  
Light Emitting ◽  
Temperature Changes ◽  
Wide Range ◽  
International Regulations ◽  
Long Lifetime ◽  
Set Up

Nowadays, signal lights are made using light-emitting diode arrays (LEDs). These devices are extremely energy efficient and have a very long lifetime. Unfortunately, especially for yellow/amber LEDs, the intensity of the light is closely related to the junction temperature. This makes it difficult to design signal lights to be used in naval, road, railway, and aeronautical sectors, capable of fully respecting national and international regulations. Furthermore, the limitations prescribed by the standards must be respected in a wide range of temperature variations. In other words, in the signaling apparatuses, a system that varies the light intensity emitted according to the operating temperature is useful/necessary. In this paper, we propose a simple and effective solution. In order to adjust the intensity of the light emitted by the LEDs, we use an LED identical to those used to emit light as a temperature sensor. The proposed system was created and tested in the laboratory. As the same device as the ones to be controlled is used as the temperature sensor, the system is very stable and easy to set up.

Sign in / Sign up

Export Citation Format

Share Document