Improved Approach to an Endwall Heat Transfer Analysis: A Linear Guide Vane and a Curved Duct

1998 ◽  
Author(s):  
A. Khalatov
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Guide Vane ◽  
Three Dimensional ◽  
Heat Transfer Analysis ◽  
Freestream Velocity ◽  
Linear Guide ◽  
Curved Duct ◽  
Experimental Correlation ◽  
The Common

This paper consists of two sections. The first section of the paper illustrates successful application of the improved approach developed by author to the endwall heat transfer data analysis in a low speed linear guide vane and in a curved duct. Effects of a three dimensional turbulent flow, a horseshoe vortex, a passage vortex, as well as an entry boundary layer thickness have been considered in both passages and as a result the common experimental correlation on a local heat transfer have been derived for the H/t = 1.0 ratio. All affected factors are presented as a superposition of the linear correction functions in the basic experimental correlation for a flat plate heat transfer. In the second section the common correlation is used as the reference correlation to establish effect of the span-to-pitch ratio on the endwall heat transfer in both passages. It was found that variation in the H/t ratio affects slightly the freestream velocity; the most important result which came from the heat transfer study is that in contrast to a curved duct a heat transfer rate in a blade passage is reduced while the H/t ratio decreases. Comparison of the experimental data obtained by the author with results of the two-dimensional heat transfer prediction confirms that it is very important to take a three-dimensional heat transfer nature into account in design of the endwall convective cooling system. It has been demonstrated that distinction between the results of two- and three dimensional approach to the endwall heat transfer can achieve up to 70% at the passage’s inlet area.

Clocking Effects of Inlet Non-Uniformities in a Fully Cooled High-Pressure Vane: A Conjugate Heat Transfer Analysis

2015 ◽  
Author(s):  
Duccio Griffini ◽  
Massimiliano Insinna ◽  
Simone Salvadori ◽  
Francesco Martelli
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cooling System ◽  
Hot Spot ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Heat Transfer Analysis

A high-pressure vane equipped with a realistic film-cooling configuration has been studied. The vane is characterized by the presence of multiple rows of fan-shaped holes along pressure and suction side while the leading edge is protected by a showerhead system of cylindrical holes. Steady three-dimensional Reynolds-Averaged Navier-Stokes (RANS) simulations have been performed. A preliminary grid sensitivity analysis with uniform inlet flow has been used to quantify the effect of spatial discretization. Turbulence model has been assessed in comparison with available experimental data. The effects of the relative alignment between combustion chamber and high-pressure vanes are then investigated considering realistic inflow conditions in terms of hot spot and swirl. The inlet profiles used are derived from the EU-funded project TATEF2. Two different clocking positions are considered: the first one where hot spot and swirl core are aligned with passage and the second one where they are aligned with the leading edge. Comparisons between metal temperature distributions obtained from conjugate heat transfer simulations are performed evidencing the role of swirl in determining both the hot streak trajectory within the passage and the coolant redistribution. The leading edge aligned configuration is resulted to be the most problematic in terms of thermal load, leading to increased average and local vane temperature peaks on both suction side and pressure side with respect to the passage aligned case. A strong sensitivity of both injected coolant mass flow and heat removed by heat sink effect has also been highlighted for the showerhead cooling system.

Clocking Effects of Inlet Nonuniformities in a Fully Cooled High-Pressure Vane: A Conjugate Heat Transfer Analysis

2015 ◽  
Vol 138 (2) ◽  
Author(s):  
Duccio Griffini ◽  
Massimiliano Insinna ◽  
Simone Salvadori ◽  
Francesco Martelli
Keyword(s):  
Heat Transfer ◽  
High Pressure ◽  
Film Cooling ◽  
Conjugate Heat Transfer ◽  
Cooling System ◽  
Hot Spot ◽  
Three Dimensional ◽  
Leading Edge ◽  
Suction Side ◽  
Heat Transfer Analysis

A high-pressure vane (HPV) equipped with a realistic film-cooling configuration has been studied. The vane is characterized by the presence of multiple rows of fan-shaped holes along pressure and suction side, while the leading edge (LE) is protected by a showerhead system of cylindrical holes. Steady three-dimensional Reynolds-averaged Navier–Stokes simulations have been performed. A preliminary grid sensitivity analysis with uniform inlet flow has been used to quantify the effect of spatial discretization. Turbulence model has been assessed in comparison with available experimental data. The effects of the relative alignment between combustion chamber and HPVs are then investigated, considering realistic inflow conditions in terms of hot spot and swirl. The inlet profiles used are derived from the EU-funded project TATEF2. Two different clocking positions are considered: the first in which hot spot and swirl core are aligned with passage; and the second in which they are aligned with the LE. Comparisons between metal temperature distributions obtained from conjugate heat transfer (CHT) simulations are performed, evidencing the role of swirl in determining both the hot streak trajectory within the passage and the coolant redistribution. The LE aligned configuration is determined to be the most problematic in terms of thermal load, leading to increased average and local vane temperature peaks on both suction side and pressure side with respect to the passage-aligned case. A strong sensitivity to both injected coolant mass flow and heat removed by heat sink effect has also been highlighted for the showerhead cooling system.

Heat Transfer Analysis of the Surface of a Nozzle Guide Vane in a Transonic Annular Cascade

2018 ◽  
Vol 11 (1) ◽  
Author(s):  
Kasem Eid Ragab ◽  
Lamyaa El-Gabry
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Guide Vane ◽  
Three Dimensional ◽  
Turbulence Models ◽  
Heat Transfer Analysis ◽  
Cfd Models ◽  
Commercial Code ◽  
Nozzle Guide ◽  
Annular Cascade

Abstract In the current study, a numerical analysis was performed for the heat transfer over the surface of nozzle guide vanes (NGVs) using three-dimensional computational fluid dynamics (CFD) models. The investigation has taken place in two stages: the baseline nonfilm-cooled NGV and the film-cooled NGV. A finite volume based commercial code was used to build and analyze the CFD models. The investigated annular cascade has no heat transfer measurements available; hence in order to validate the CFD models against experimental data, two standalone studies were carried out on the NASA C3X vanes, one on the nonfilm-cooled C3X vane and the other on the film-cooled C3X vane. Different modeling parameters were investigated including turbulence models in order to obtain good agreement with the C3X experimental data; the same parameters were used afterward to model the industrial NGVs.

Conjugate heat transfer analysis of a radially cooled nozzle guide vane in an aero gas turbine engine

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
G. L. Arunkumar ◽  
Balachandra P. Shetty ◽  
R. K. Mishra
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Conjugate Heat Transfer ◽  
Guide Vane ◽  
Three Dimensional ◽  
Computational Method ◽  
Heat Transfer Analysis ◽  
Turbine Engine ◽  
Barrier Coating ◽  
Nozzle Guide

Abstract This paper presents a computational method to investigate cooling performance of NASA-C3X cascade vane coated with thermal barrier coating (TBC), for which experimental data are available. The vane was cooled internally by air flows through radially oriented 10 channels. A three-dimensional conjugate heat transfer simulation has been performed which allows the conduction-convection on metal vane by eliminating need of multiple boundary solutions. The predicted aerodynamic and thermal loads with the effect of turbulent intensity is found to be good agreement with experimental data and inclusion of TBC leads to quantitative reduction in vane metal temperature.

Conjugate heat transfer analysis of a radially cooled nozzle guide vane in an aero gas turbine engine

2020 ◽  
Vol 0 (0) ◽  
Author(s):  
G. L. Arunkumar ◽  
Balachandra P. Shetty ◽  
R. K. Mishra
Keyword(s):  
Heat Transfer ◽  
Experimental Data ◽  
Conjugate Heat Transfer ◽  
Guide Vane ◽  
Three Dimensional ◽  
Computational Method ◽  
Heat Transfer Analysis ◽  
Turbine Engine ◽  
Barrier Coating ◽  
Nozzle Guide

AbstractThis paper presents a computational method to investigate cooling performance of NASA-C3X cascade vane coated with thermal barrier coating (TBC), for which experimental data are available. The vane was cooled internally by air flows through radially oriented 10 channels. A three-dimensional conjugate heat transfer simulation has been performed which allows the conduction-convection on metal vane by eliminating need of multiple boundary solutions. The predicted aerodynamic and thermal loads with the effect of turbulent intensity is found to be good agreement with experimental data and inclusion of TBC leads to quantitative reduction in vane metal temperature.

Three-dimensional heat transfer analysis of flat-plate oscillating heat pipes

2021 ◽  
pp. 117189
Author(s):  
Kimihide Odagiri ◽  
Kieran Wolk ◽  
Stefano Cappucci ◽  
Stefano Morellina ◽  
Scott Roberts ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Flat Plate ◽  
Three Dimensional ◽  
Heat Pipes ◽  
Heat Transfer Analysis

scholarly journals Numerical heat transfer analysis of micro-scale jet-impingement cooling in a high-pressure turbine vane

2021 ◽  
Author(s):  
Karan Anand
Keyword(s):  
Heat Transfer ◽  
Three Dimensional ◽  
Jet Impingement ◽  
Local Heat Transfer ◽  
Local Heat ◽  
Heat Transfer Analysis ◽  
Transfer Rates ◽  
Numerical Heat Transfer ◽  
Turbine Vane ◽  
Single Jet

This research provides a computational analysis of heat transfer due to micro jet-impingement inside a gas turbine vane. A preliminary-parametric analysis of axisymmetric single jet was reported to better understand micro jet-impingement. In general, it was seen that as the Reynolds number increased the Nusselt number values increased. The jet to target spacing had a considerably lower impact on the heat transfer rates. Around 30% improvement was seen by reducing the diameter to half while changing the shape to an ellipse saw 20.8% improvement in Nusselt value. The numerical investigation was then followed by studying the heat transfer characteristics in a three-dimensional, actual-shaped turbine vane. Effects of jet inclination showed enhanced mixing and secondary heat transfer peaks. The effect of reducing the diameter of the jets to 0.125 mm yielded 55% heat transfer improvements compared to 0.51 mm; the tapering effect also enhanced the local heat transfer values as local velocities at jet exit increased.

HP Vane Aerodynamics and Heat Transfer in the Presence of Aggressive Inlet Swirl

2012 ◽  
Vol 135 (2) ◽  
Author(s):  
Imran Qureshi ◽  
Andy D. Smith ◽  
Thomas Povey
Keyword(s):  
Heat Transfer ◽  
Cooling System ◽  
Three Dimensional ◽  
Leading Edge ◽  
Good Deal ◽  
Vortex Center ◽  
Research Facility ◽  
Lean Burn ◽  
Numerical Predictions ◽  
The Impact

Modern lean burn combustors now employ aggressive swirlers to enhance fuel-air mixing and improve flame stability. The flow at combustor exit can therefore have high residual swirl. A good deal of research concerning the flow within the combustor is available in open literature. The impact of swirl on the aerodynamic and heat transfer characteristics of an HP turbine stage is not well understood, however. A combustor swirl simulator has been designed and commissioned in the Oxford Turbine Research Facility (OTRF), previously located at QinetiQ, Farnborough UK. The swirl simulator is capable of generating an engine-representative combustor exit swirl pattern. At the turbine inlet plane, yaw and pitch angles of over ±40 deg have been simulated. The turbine research facility used for the study is an engine scale, short duration, rotating transonic turbine, in which the nondimensional parameters for aerodynamics and heat transfer are matched to engine conditions. The research turbine was the unshrouded MT1 design. By design, the center of the vortex from the swirl simulator can be clocked to any circumferential position with respect to HP vane, and the vortex-to-vane count ratio is 1:2. For the current investigation, the clocking position was such that the vortex center was aligned with the vane leading edge (every second vane). Both the aligned vane and the adjacent vane were characterized. This paper presents measurements of HP vane surface and end wall heat transfer for the two vane positions. The results are compared with measurements conducted without swirl. The vane surface pressure distributions are also presented. The experimental measurements are compared with full-stage three-dimensional unsteady numerical predictions obtained using the Rolls Royce in-house code Hydra. The aerodynamic and heat transfer characterization presented in this paper is the first of its kind, and it is hoped to give some insight into the significant changes in the vane flow and heat transfer that occur in the current generation of low NOx combustors. The findings not only have implications for the vane aerodynamic design, but also for the cooling system design.

A Conjugate 3-D Flow and Heat Transfer Analysis of a Thermal Barrier Cooled Turbine Guide Vane

1998 ◽  
Author(s):  
Dieter E. Bohn ◽  
Volker J. Becker
Keyword(s):  
Heat Transfer ◽  
Gas Turbines ◽  
Guide Vane ◽  
Suction Side ◽  
Heat Transfer Analysis ◽  
Thermal Barrier ◽  
Trailing Edge ◽  
Flow And Heat Transfer ◽  
Turbine Guide Vane ◽  
Basic Configuration

This paper presents the numerical investigations of the flow and heat transfer of two configurations of a transonic turbine guide vane. The basic configuration is a vane with convection cooling. The second configuration is additionally coated with a thermal barrier consisting of ZrO2. The results are obtained with a conjugate heat transfer and flow computer code that has been developed at the Institute of Steam and Gas Turbines. Measurement data is available for the basic configuration and the computational results are compared to the experimental results. The results show very good agreement between calculated and measured vane surface temperatures. The trailing edge turns out to be subjected to high thermal loads as it is too thin to be cooled effectively. Secondary flow phenomena like the passage vortex and the corner vortex and their impact on the temperature distribution are discussed. The ZrO2 coating is calculated for a thickness of 300μm. The substrate material temperatures are lowered by about 20 K–29 K in the stagnation point area and by about 27 K–43 K in the shock area on the suction side. At the trailing edge, the coating on the suction side and on the pressure side hardly influences the metal temperature.

Sign in / Sign up

Export Citation Format

Share Document