scholarly journals Intercooled and Recuperated Dresser-Rand DC990 Gas Turbine Engine

1989 ◽  
Author(s):  
James E. Staudt ◽  
Dietrich Birkholz ◽  
Willem Jansen ◽  
John J. Tuzson
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Heat Rate ◽  
Gas Turbine Engine ◽  
Preliminary Design ◽  
Turbine Engine ◽  
Design Point ◽  
Performance Improvements ◽  
Industrial Gas Turbine ◽  
Engine Power

A preliminary design for a Dresser-Rand DC990 industrial gas turbine engine modified for intercooling and recuperation (ICR) is presented. The DC990 was selected because its configuration is amenable to intercooling and because it is in the power range of interest. Based upon preliminary estimates, engine power output will increase from 6000 bhp to 8400 bhp at design point. Design point specific fuel consumption will be reduced 26% to a heat rate of 6300 BTU/bhp-hr. Moreover, the DC990 ICR engine maintains a high thermal efficiency during part-load operation. These performance improvements are achievable using proven, low-risk technology. The resulting combination of low fuel consumption and low maintenance costs makes the DC990 ICR gas turbine engine an attractive engine package for several applications.

scholarly journals Ceramic Composites for Industrial Gas Turbine Engine Applications: DOE CFCC Phase 1 Evaluations

1995 ◽  
Author(s):  
Gregory S. Corman ◽  
Jeffrey T. Heinen ◽  
Raymond H. Goetze
Keyword(s):  
Gas Turbine ◽  
Gas Turbines ◽  
Phase 1 ◽  
Engine Performance ◽  
Ceramic Composites ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Performance Improvements ◽  
Component Design ◽  
Industrial Gas Turbine

Conceptual design evaluations of the use of continuous fiber ceramic composite (CFCC) turbine shrouds and combustor liners in an industrial gas turbine engine were performed under Phase 1 of the DOE CFCC program. Significant engine performance improvements were predicted with the use of CFCC components. Five composite systems were evaluated for use as shrouds and combustor liners, the results of which are discussed with particular reference to Toughened Silcomp. Several current CFCC materials were judged to be relatively close to meeting the short term performance requirements of such a system. However, additional CFCC property data are required for significant component design optimization and life prediction, two key design steps that must be completed before ceramic composites can be utilized in large gas turbines.

LV100 AIPS Technology—For Future Army Propulsion

1992 ◽  
Author(s):  
Walter Brockett ◽  
Angelo Koschier
Keyword(s):  
Control Systems ◽  
Gas Turbine ◽  
Fuel Consumption ◽  
Cooling System ◽  
Gas Turbine Engine ◽  
Air Filtration ◽  
Turbine Engine ◽  
Overall Design ◽  
Armored Vehicle ◽  
And Control

The overall design of and Advanced Integrated Propulsion System (AIPS), powered by an LV100 gas turbine engine, is presented along with major test accomplishments. AIPS was a demonstrator program that included design, fabrication, and test of an advanced rear drive powerpack for application in a future heavy armored vehicle (54.4 tonnes gross weight). The AIPS design achieved significant improvements in volume, performance, fuel consumption, reliability/durability, weight and signature reduction. Major components of AIPS included the recuperated LV100 turbine engine, a hydrokinetic transmission, final drives, self-cleaning air filtration (SCAF), cooling system, signature reduction systems, electrical and hydraulic components, and control systems with diagnostics/prognostics and maintainability features.

Design and Analysis of a High Pressure Turbine Using Computational Methods for Small Gas Turbine Application

2013 ◽  
Author(s):  
Kishor Kumar ◽  
R. Prathapanayaka ◽  
S. V. Ramana Murthy ◽  
S. Kishore Kumar ◽  
T. M. Ajay Krishna
Keyword(s):  
High Pressure ◽  
Gas Turbine ◽  
Computational Methods ◽  
Gas Turbine Engine ◽  
Flow Coefficient ◽  
Design Parameters ◽  
Convergence Criterion ◽  
Turbine Engine ◽  
Design Point ◽  
Ansys Cfx

This paper describes the aerodynamic design and analysis of a high-pressure, single-stage axial flow turbine suitable for small gas turbine engine application using computational methods. The specifications of turbine were based on the need of a typical high-pressure compressor and geometric restrictions of small gas turbine engine. Baseline design parameters such as flow coefficient, stage loading coefficient are close to 0.23 and 1.22 respectively with maximum flow expansion in the NGV rows. In the preliminary design mode, the meanline approach is used to generate the turbine flow path and the design point performance is achieved by considering three blade sections at hub, mean and tip using the AMDC+KO+MK+BSM loss models to meet the design constraints. An average exit swirl angle of less than 5 degrees is achieved leading to minimum losses in the stage. Also, NGV and rotor blade numbers were chosen based on the optimum blade solidity. Blade profile is redesigned using the results from blade-to-blade analysis and through-flow analysis based on an enhanced Dawes BTOB3D flow solver. Using PbCFD (Pushbutton CFD) and commercially available CFD software ANSYS-CFX, aero-thermodynamic parameters like pressure ratios, aerodynamic power, and efficiencies are computed and these results are compared with one another. The boundary conditions, convergence criterion, and turbulence model used in CFD computations are set uniform for comparison with 8 per cent turbulence intensity. Grid independence study is performed at design point to optimize the grid density for off-design performance predictions. ANSYS-CFX and PbCFD have predicted higher efficiency of 3.4% and 1.2% respectively with respect to targeted efficiency of 89 per cent.

scholarly journals Industrial Gas Turbine Engine Catalytic Pilot Combustor-Prototype Testing

2010 ◽  
Author(s):  
Shahrokh Etemad ◽  
Benjamin Baird ◽  
Sandeep Alavandi ◽  
William Pfefferle
Keyword(s):  
Gas Turbine ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Industrial Gas Turbine ◽  
Prototype Testing

Cycle Design Exploration Using Multi-Design Point Approach

2012 ◽  
Author(s):  
Jeffrey Schutte ◽  
Jimmy Tai ◽  
Jonathan Sands ◽  
Dimitri Mavris
Keyword(s):  
Gas Turbine ◽  
Design Space ◽  
Traditional Approach ◽  
Gas Turbine Engine ◽  
Operating Conditions ◽  
Feasible Region ◽  
Turbine Engine ◽  
Design Point ◽  
Performance Requirements ◽  
Design Cycle

The focus of this study is to compare the aerothermodynamic cycle design space of a gas turbine engine generated using two on-design approaches. The traditional approach uses a single design point (SDP) for on-design cycle analysis, where off-design cycle analysis must be performed at other operating conditions of interest. A multi-design point (MDP) method performs on-design cycle analysis at all operating conditions where performance requirements are specified. Effects on the topography of the cycle design space as well as the feasibility of the space are examined. The impacts that performance requirements and cycle assumptions have on the bounds and topography of the feasible space are investigated. The deficiencies of a SDP method in determining an optimum gas turbine engine will be shown for a given set of requirements. Analysis will demonstrate that the MDP method, unlike the SDP method, always obtains a properly sized engine for a set of given requirements and cycle design variables, resulting in an increased feasible region of the aerothermodynamic cycle design space from which the optimum performance engine can be obtained.

Off-Design Characteristics of Low-Fuel Consumption Gas Turbine Engine for Long-Range UAV

2013 ◽  
Author(s):  
Roberto Andriani ◽  
Umberto Ghezzi ◽  
Antonella Ingenito ◽  
Fausto Gamma ◽  
Antonio Agresta
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Long Range ◽  
Gas Turbine Engine ◽  
Turbine Engine ◽  
Design Characteristics

Performance and Emission Characteristics of a Small Scale Gas Turbine Engine Fueled With Propanol/Jet A Blends

2011 ◽  
Author(s):  
Carlos J. Mendez ◽  
Ramkumar N. Parthasarathy ◽  
Subramanyam R. Gollahalli
Keyword(s):  
Gas Turbine ◽  
Fuel Consumption ◽  
Gas Turbine Engine ◽  
Single Stage ◽  
Specific Fuel Consumption ◽  
Small Scale ◽  
Emission Characteristics ◽  
Turbine Engine ◽  
Performance And Emission ◽  
Emission Index

Alcohols serve as an alternate energy resource to the conventional petroleum-based fuels. The objective of this study was to document the performance and emission characteristics of blends of n-propanol and Jet A fuel in a small-scale gas turbine engine. The experiments were conducted in a 30kW gas turbine engine with a single-stage centrifugal flow compressor, annular combustion chamber and a single-stage axial flow turbine. In addition to neat propanol and Jet A fuel, three blends, with 25%, 50% and 75% of propanol by volume, were used as the fuels. The thrust, thrust-specific fuel consumption, and the concentrations of CO and NOx in the exhaust were measured and compared with those measured with Jet A fuel. The engine was operated at the same throttle settings with all the fuels. The operational range of engine rotational speed was shifted downwards with the addition of propanol due to its lower heating value. The thrust specific fuel consumption increased with the addition of propanol, while the CO emission index increased and NOx emission index decreased.

Sign in / Sign up

Export Citation Format

Share Document