scholarly journals Observations of Separated Laminar Flow on Axial Compressor Blading

1975 ◽  
Author(s):  
G. J. Walker
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Separation Bubble ◽  
Axial Compressor ◽  
Theoretical Models ◽  
Bubble Behavior ◽  
Number Range ◽  
Laminar Separation ◽  
Bubble Bursting

This paper describes some detailed observations of separated laminar flow regions on the rotating and stationary blading of a single-stage axial compressor operating at low speed. The data covers the “critical” Reynolds number range where “bursting” of laminar separation bubbles causes a sharp increase in blade profile losses. The experimental results are compared with various empirical correlations and theoretical models proposed by other workers. Horton’s semi-empirical model of separation bubble bursting is broadly supported by the present investigation. However, it appears that some aspects of Horton’s theory require significant modification in order to give an accurate description of the separation bubble behavior on the blades in an axial compressor. It is stressed that correlations of the critical Reynolds number for axial compressor cascades in terms of overall performance parameters should be applied with caution, as they are only likely to be valid for a narrow range of conditions.

LOW REYNOLDS NUMBER FLOW OVER A SQUARE RIB

1997 ◽  
Vol 21 (4) ◽  
pp. 371-387
Author(s):  
D.A Billenness ◽  
N. Djilali ◽  
E. Zeidan
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Separation Bubble ◽  
Three Dimensional ◽  
Recirculation Region ◽  
Number Range ◽  
Reynolds Number Flow ◽  
First Results ◽  
Region Length ◽  
Number Flow

Laminar flow over a square rib placed in a fully developed channel flow is investigated over the Reynolds number range 80-350. The effect of Reynolds number on the flow and the variation of the primary reattachment length with Reynolds number are investigated using flow visualization and laser-Doppler velocimetry. The primary recirculation region length is found to increase in a slightly non-linear fashion with Reynolds number up to Reh = 250, at which point shear layer instabilities first appear downstream of the rib. Increasing the Reynolds number further, first results in continuing growth of the separation bubble, and then for Reh ≳ 300, in the appearance of three dimensional vortices and gradual shortening of the bubble. The measurements are complemented by two- and three-dimensional numerical simulations using a finite volume method with a high-order descretization scheme. These simulations yield excellent agreement with the measured reattachment lengths and velocity profiles over the steady laminar flow régime.

The Effect of Reynolds Number and Laminar Separation on Axial Cascade Performance

1975 ◽  
Vol 97 (2) ◽  
pp. 261-273 ◽  
Author(s):  
W. B. Roberts
Keyword(s):  
Reynolds Number ◽  
Shear Layer ◽  
Separation Bubble ◽  
Axial Compressor ◽  
Leading Edge ◽  
Practical Method ◽  
Reynolds Numbers ◽  
Compressor Cascade ◽  
Laminar Separation ◽  
Semiempirical Theory

Testing over a range of Reynolds numbers was done for three NACA 65 Profiles in cascade. The testing was carried out in the VKI C-1 Low Speed Cascade Wind Tunnel; blade chord Reynolds number was varied from 250,000 to 40,000. A semiempirical theory is developed which will predict the behavior of the shear layer across a laminar separation bubble. The method is proposed for two-dimensional incompressible flow and is applicable down to short bubble bursting. The method can be used to predict the length of the laminar bubble, the bursting Reynolds number, and the development of the shear layer through the separated region. As such it is a practical method for calculating the profile losses of axial compressor and turbine cascades in the presence of laminar separation bubbles. It can also be used to predict the abrupt leading edge stall associated with thin airfoil sections. The predictions made by the method are compared with the available experimental data. The agreement could be considered good. The method was also used to predict regions of laminar separation in converging flows through axial compressor cascades (exterior to the corner vortices) with good results. For Reynolds numbers below bursting the semiempirical theory no longer applies. For this situation the performance of an axial compressor cascade can be computed using an empirical correlation proposed by the author. Comparison of performance prediction with experiment shows satisfactory agreement. Finally, a tentative correlation, based on the NACA Diffusion Factor, is presented that allows a rapid estimation of the bursting Reynolds number of an axial compressor cascade.

Bifurcation Characteristics of Flows in Rectangular Sudden Expansion Channels

2005 ◽  
Author(s):  
Francine Battaglia ◽  
George Papadopoulos
Keyword(s):  
Reynolds Number ◽  
Laminar Flow ◽  
Critical Reynolds Number ◽  
Three Dimensional ◽  
Reynolds Numbers ◽  
Expansion Ratio ◽  
Sudden Expansion ◽  
Two Dimensional ◽  
Effective Expansion ◽  
Three Dimensional Simulations

The effect of three-dimensionality on low Reynolds number flows past a symmetric sudden expansion in a channel was investigated. The geometric expansion ratio of in the current study was 2:1 and the aspect ratio was 6:1. Both experimental velocity measurements and two- and three-dimensional simulations for the flow along the centerplane of the rectangular duct are presented for Reynolds numbers in the range of 150 to 600. Comparison of the two-dimensional simulations with the experiments revealed that the simulations fail to capture completely the total expansion effect on the flow, which couples both geometric and hydrodynamic effects. To properly do so requires the definition of an effective expansion ratio, which is the ratio of the downstream and upstream hydraulic diameters and is therefore a function of both the expansion and aspect ratios. When the two-dimensional geometry was consistent with the effective expansion ratio, the new results agreed well with the three-dimensional simulations and the experiments. Furthermore, in the range of Reynolds numbers investigated, the laminar flow through the expansion underwent a symmetry-breaking bifurcation. The critical Reynolds number evaluated from the experiments and the simulations was compared to other values reported in the literature. Overall, side-wall proximity was found to enhance flow stability, helping to sustain laminar flow symmetry to higher Reynolds numbers in comparison to nominally two-dimensional double-expansion geometries. Lastly, and most importantly, when the logarithm of the critical Reynolds number from all these studies was plotted against the reciprocal of the effective expansion ratio, a linear trend emerged that uniquely captured the bifurcation dynamics of all symmetric double-sided planar expansions.

Experimental and Numerical Investigation of Transition Effects on a Low Reynolds Number Airfoil

2017 ◽  
Author(s):  
Michael J. Collison ◽  
Peter X. L. Harley ◽  
Domenico di Cugno
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Separation Bubble ◽  
Low Reynolds Number ◽  
Flow Visualisation ◽  
Transition Model ◽  
Laminar Separation ◽  
Oil Flow ◽  
Low Reynolds ◽  
Low Reynolds Number Airfoil

Low speed, small scale turbomachinery operates at low Reynolds number with transition phenomena occurring. In small consumer product applications, high efficiency and low noise are key performance metrics. Transition behaviour will partly determine the state of the boundary layer at the trailing edge; whether it is laminar, turbulent or separated impacts aerodynamic and acoustic performance. This study aimed to evaluate a commercially available CFD transition model on a low Reynolds number Eppler E387 airfoil and identify whether it was able to correctly model the boundary layer transition, and at what expense. CFD was carried out utilising the ANSYS Shear Stress Transport (SST) k-ω γ-Reθ transition model. The CFD progressed from 2D in Fluent v150, through to single cell thickness 3D (pseudo 2D) in CFX v172. An Eppler E387 low Reynolds number airfoil, for which experimental data was readily available from literature at Re = 200,000 was used as the validation case for the CFD, with results computed at numerous incidence angles and mesh densities. Additionally, experimental surface oil flow visualisation was undertaken in a wind tunnel using a scaled E387 airfoil for the zero incidence case at Re = 50,000. The flow visualisation exhibited the expected key features of transition in the breakdown of the boundary layer from laminar to turbulent, and was used as a validation case for the CFD transition model. The comparison between the results from the CFD transition model and the experimental data from literature suggested varying levels of agreement based on the mesh density and CFD solver in the starting location of the laminar separation bubble, with higher disparity for the position of the reattachment point. Whether 2D or 3D, the prediction accuracy was seen to worsen at high incidence angles. Finally, the location of the laminar separation bubble between CFD and oil flow visualisation had good agreement and a set of guidelines on the mesh parameters which can be applied to low Reynolds number turbomachinery simulations was determined.

Transition Mechanisms in Laminar Separated Flow Under Simulated Low Pressure Turbine Aerofoil Conditions

2012 ◽  
Vol 135 (1) ◽  
Author(s):  
Jerrit Dähnert ◽  
Christoph Lyko ◽  
Dieter Peitsch
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Separated Flow ◽  
Low Pressure ◽  
Main Flow ◽  
Test Facility ◽  
Flow Conditions ◽  
Laminar Separation ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Based on detailed experimental work conducted at a low speed test facility, this paper describes the transition process in the presence of a separation bubble with low Reynolds number, low free-stream turbulence, and steady main flow conditions. A pressure distribution has been created on a long flat plate by means of a contoured wall opposite of the plate, matching the suction side of a modern low-pressure turbine aerofoil. The main flow conditions for four Reynolds numbers, based on suction surface length and nominal exit velocity, were varied from 80,000 to 300,000, which covers the typical range of flight conditions. Velocity profiles and the overall flow field were acquired in the boundary layer at several streamwise locations using hot-wire anemometry. The data given is in the form of contours for velocity, turbulence intensity, and turbulent intermittency. The results highlight the effects of Reynolds number, the mechanisms of separation, transition, and reattachment, which feature laminar separation-long bubble and laminar separation-short bubble modes. For each Reynolds number, the onset of transition, the transition length, and the general characteristics of separated flow are determined. These findings are compared to the measurement results found in the literature. Furthermore, the experimental data is compared with two categories of correlation functions also given in the literature: (1) correlations predicting the onset of transition and (2) correlations predicting the mode of separated flow transition. Moreover, it is shown that the type of instability involved corresponds to the inviscid Kelvin-Helmholtz instability mode at a dominant frequency that is in agreement with the typical ranges occurring in published studies of separated and free-shear layers.

Acoustic and phase portrait analysis of leading-edge roughness element on laminar separation bubbles at low Reynolds number flow

2021 ◽  
pp. 095441002110443
Author(s):  
Hossein Jabbari ◽  
Esmaeili Ali ◽  
Mohammad Hasan Djavareshkian
Keyword(s):  
Reynolds Number ◽  
Phase Portrait ◽  
Separation Bubble ◽  
Roughness Element ◽  
Low Reynolds Number ◽  
Leading Edge ◽  
Suction Side ◽  
Laminar Separation ◽  
Roughness Elements ◽  
Edge Roughness

Since laminar separation bubbles are neutrally shaped on the suction side of full-span wings in low Reynolds number flows, a roughness element can be used to improve the performance of micro aerial vehicles. The purpose of this article was to investigate the leading-edge roughness element’s effect and its location on upstream of the laminar separation bubble from phase portrait point of view. Therefore, passive control might have an acoustic side effect, especially when the bubble might burst and increase noise. Consequently, the effect of the leading-edge roughness element features on the bubble’s behavior is considered on the acoustic pressure field and the vortices behind the NASA-LS0417 cross-section. The consequences express that the distribution of roughness in the appropriate dimensions and location could contribute to increasing the performance of the airfoil and the interaction of vortices produced by roughness elements with shear layers on the suction side has increased the sound frequency in the relevant sound pressure level (SPL). The results have demonstrated that vortex shedding frequency was increased in the presence of roughness compared to the smooth airfoil. Also, more complexity of the phase portrait circuits was found, retrieved from velocity gradient limitation. Likewise, the highest SPL is related to the state where the separation bubble phenomenon is on the surface versus placing roughness elements on the leading edge leads to a negative amount of SPL.

Assessment of Different Turbulence Models for Predicting Laminar Separation Bubble Over Thick Airfoils

2015 ◽  
Author(s):  
Saravana Kumar Lakshmanan ◽  
Alok Mishra ◽  
Ashoke De
Keyword(s):  
Reynolds Number ◽  
Numerical Study ◽  
Separation Bubble ◽  
Turbulence Models ◽  
Laminar Separation Bubble ◽  
Laminar Separation ◽  
Performance Variables ◽  
Rans Models ◽  
High Angles Of Attack ◽  
Aerodynamic Lift

Accurate laminar-turbulent prediction is very much important to understand the complete performance characteristics of any airfoil which operates at low and medium Reynolds number. In this article, a numerical study has been performed over two different thick airfoils operating at low Reynolds number using k-ω SST, k-kl-ω and Spalart-Allmaras (SA) RANS models. The unsteady two dimensional (2D) simulations are performed over NACA 0021 and NACA 65-021 at Re 120,000 for a range of angle of attacks. The performances of these models are assessed through aerodynamic lift, drag and pressure coefficients. To obtain better comparison, the simulated results are compared with the experimental measurements and XFOIL results as well. In this present study, it is found that the k-kl-ω transition model is capable of predicting correct lift, drag coefficient and separation bubble as reported in experiments. At high angles of attack, this model fails to predict performance variables accurately. The SA and SST models are fail to predict laminar separation bubble. However, At high angle of attack, SA model shows better predictions compared to k-kl-ω and k-ω SST models.

Shear Layer Development, Separation, and Stability Over a Low-Reynolds Number Airfoil

2018 ◽  
Vol 140 (7) ◽  
Author(s):  
Paul Ziadé ◽  
Mark A. Feero ◽  
Philippe Lavoie ◽  
Pierre E. Sullivan
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Shear Layer ◽  
Separation Bubble ◽  
Low Reynolds Number ◽  
Base Flow ◽  
Mean Velocity ◽  
Laminar Separation ◽  
Low Reynolds ◽  
Layer Development

The shear layer development for a NACA 0025 airfoil at a low Reynolds number was investigated experimentally and numerically using large eddy simulation (LES). Two angles of attack (AOAs) were considered: 5 deg and 12 deg. Experiments and numerics confirm that two flow regimes are present. The first regime, present for an angle-of-attack of 5 deg, exhibits boundary layer reattachment with formation of a laminar separation bubble. The second regime consists of boundary layer separation without reattachment. Linear stability analysis (LSA) of mean velocity profiles is shown to provide adequate agreement between measured and computed growth rates. The stability equations exhibit significant sensitivity to variations in the base flow. This highlights that caution must be applied when experimental or computational uncertainties are present, particularly when performing comparisons. LSA suggests that the first regime is characterized by high frequency instabilities with low spatial growth, whereas the second regime experiences low frequency instabilities with more rapid growth. Spectral analysis confirms the dominance of a central frequency in the laminar separation region of the shear layer, and the importance of nonlinear interactions with harmonics in the transition process.

Transition Mechanisms in Laminar Separated Flow Under Simulated Low Pressure Turbine Airfoil Conditions

2011 ◽  
Author(s):  
Jerrit Da¨hnert ◽  
Christoph Lyko ◽  
Dieter Peitsch
Keyword(s):  
Reynolds Number ◽  
Separation Bubble ◽  
Separated Flow ◽  
Low Pressure ◽  
Main Flow ◽  
Test Facility ◽  
Flow Conditions ◽  
Laminar Separation ◽  
Free Stream Turbulence ◽  
Low Pressure Turbine

Based on detailed experimental work conducted at a low speed test facility, this paper describes the transition process in the presence of a separation bubble with low Reynolds number, low free-stream turbulence, and steady main flow conditions. A pressure distribution has been created on a long flat plate by means of a contoured wall opposite of the plate, matching the suction side of a modern low-pressure turbine aerofoil. The main flow conditions for four Reynolds numbers, based on suction surface length and nominal exit velocity, were varied from 80,000 to 300,000, which covers the typical range of flight conditions. Velocity profiles and the overall flow field were acquired in the boundary layer at several streamwise locations using hot-wire anemometry. The data given is in the form of contours for velocity, turbulence intensity, and turbulent intermittency. The results highlight the effects of Reynolds number, the mechanisms of separation, transition, and reattachment, which feature laminar separation-long bubble and laminar separation-short bubble modes. For each Reynolds number, the onset of transition, the transition length, and the general characteristics of separated flow are determined. These findings are compared to the measurement results found in the literature. Furthermore, the experimental data is compared with two categories of correlation functions also given in the open literature: (1) correlations predicting the onset of transition and (2) correlations predicting the mode of separated flow transition. Moreover, it is shown that the type of instability involved corresponds to the inviscid Kelvin-Helmholtz instability mode at a dominant frequency that is in agreement with the typical ranges occurring in published studies of separated and free-shear layers.

Sign in / Sign up

Export Citation Format

Share Document