Modeling NO and Soot Emissions With Gas Compressibility

2001 ◽  
Author(s):  
Hatem M. Wasfy ◽  
Chia-fon F. Lee
Keyword(s):  
Compression Ratio ◽  
Fuel Injection ◽  
Equilibrium Concentration ◽  
Ideal Gas ◽  
Peak Cylinder Pressure ◽  
Engine Combustion ◽  
Curvilinear Coordinate ◽  
Conversion Time ◽  
Soot Emissions ◽  
Experimental Values

Abstract A multidimensional engine combustion code was used to model NO and soot emissions from a heavy duty Cummins Diesel engine with a compression ratio of 16. The code solves the gas calculation in a moving curvilinear coordinate system. The code includes a 13 species chemistry model that calculates the rate of formation of each species from the fuel conversion time and the species equilibrium concentration. The code also models fuel injection, spray impingement and secondary spray breakup. The engine was tested with 10% EGR in the intake by mass, a swirl ratio of 2.1 and an engine speed of 1500 rpm. The engine was tested at 3 different injection timings. The consequence of including compressibility effects is also studied. The Redlich-Kwong model was used to calculate the deviation of the gases within the combustion chamber from ideal gas behavior. The computational results were compared to the values of pressure, NO and soot emissions obtained from experiments. At the high compression ratio that the engine operates under, the ideal gas equation was found to under-predict the peak cylinder pressure by about 4%. The soot emissions were closely matched in both value and trend. Due to the inaccuracy of the equilibrium-based chemical model, the calculated NO emissions were higher than the experimental values. The evolution of the NO and soot emissions during the cycle was studied. The processes that form these emissions were identified.

Novel strategies to overcome the limitations of a low compression ratio light duty diesel engine

2020 ◽  
pp. 146808742096198
Author(s):  
V Vikraman ◽  
K Anand ◽  
A Ramesh
Keyword(s):  
Diesel Engine ◽  
Compression Ratio ◽  
Diesel Engines ◽  
High Speed ◽  
Fuel Injection ◽  
Cooling System ◽  
Parameters Optimization ◽  
Oxides Of Nitrogen ◽  
Load Range ◽  
Soot Emissions

Low compression ratio (LCR) approach in diesel engines can reduce the oxides of nitrogen (NOx) and soot emissions simultaneously owing to lower temperatures and longer fuel-air premixing time. The present work investigates the effects of lowering the geometric compression ratio (CR) from 18:1 to 14:1 in a naturally aspirated (NA) single cylinder common rail direct injection (CRDI) diesel engine. Based on the investigations done across the entire speed and load range, significant benefits were observed in the NOx and soot emissions. However, lowering the compression ratio had adverse effects on brake specific fuel consumption (BSFC), unburned hydrocarbon (HC) and carbon monoxide (CO) emissions, especially at low-load and high-speed operating points. To overcome these limitations, novel strategies including split-cooling system (SCS) and secondary exhaust valve opening (SEVO) are proposed in the present work. While the fuel injection parameters optimization specific to LCR could help to improve the BSFC, HC and CO emissions penalty to a reasonable extent, the SCS concept can provide further benefits by reducing the heat loss to coolant and improving the engine component temperatures. Increasing the residual gas fraction using the optimized SEVO concept could further improve the charge temperature leading to a further reduction in the BSFC, HC and CO emissions. The net benefits of the optimized LCR approach are quantified for the modified Indian drive cycle (MIDC) using a one-dimensional simulation tool. The results obtained show a signification reduction of 22% and 74% in NOx and soot emissions respectively as compared to the base 18 CR engine results. Moreover, the penalty in HC and CO emissions could be contained to a large extent resulting in only a slight penalty of 23% and 20% respectively. Furthermore, the higher BSFC with the LCR approach could be successfully addressed and the final values were found to be better than the stock compression ratio by 1.5%. Overall, the strategies proposed in the present work are found to be beneficial to develop modern diesel engines in compliance with the future emission regulations which demand extreme control on NOx and soot emissions.

The combined effect of lattice’s uniaxial strains and electron–phonon interaction’s screening on TBEC of the intersite bipolarons

2016 ◽  
Vol 30 (26) ◽  
pp. 1650186
Author(s):  
B. Yavidov ◽  
SH. Djumanov ◽  
T. Saparbaev ◽  
O. Ganiyev ◽  
S. Zholdassova ◽  
...  
Keyword(s):  
Ideal Gas ◽  
Einstein Condensation ◽  
Chain Model ◽  
One Dimensional ◽  
Electron Phonon Interaction ◽  
Model Lattice ◽  
Experimental Values ◽  
Bose Einstein ◽  
Derivatives Of ◽  
The Ideal

Having accepted a more generalized form for density-displacement type electron–phonon interaction (EPI) force we studied the simultaneous effect of uniaxial strains and EPI’s screening on the temperature of Bose–Einstein condensation [Formula: see text] of the ideal gas of intersite bipolarons. [Formula: see text] of the ideal gas of intersite bipolarons is calculated as a function of both strain and screening radius for a one-dimensional chain model of cuprates within the framework of Extended Holstein–Hubbard model. It is shown that the chain model lattice comprises the essential features of cuprates regarding of strain and screening effects on transition temperature [Formula: see text] of superconductivity. The obtained values of strain derivatives of [Formula: see text] [Formula: see text] are in qualitative agreement with the experimental values of [Formula: see text] [Formula: see text] of La[Formula: see text]Sr[Formula: see text]CuO4 under moderate screening regimes.

scholarly journals Possibilities of Simultaneous In-Cylinder Reduction of Soot andNOxEmissions for Diesel Engines with Direct Injection

2008 ◽  
Vol 2008 ◽  
pp. 1-13 ◽  
Author(s):  
U. Wagner ◽  
P. Eckert ◽  
U. Spicher
Keyword(s):  
Nitrogen Oxide ◽  
Diesel Engines ◽  
Fuel Injection ◽  
Soot Formation ◽  
Soot Oxidation ◽  
The Other ◽  
Injection System ◽  
Nitrogen Oxide Emissions ◽  
Injection Strategy ◽  
Soot Emissions

Up to now, diesel engines with direct fuel injection are the propulsion systems with the highest efficiency for mobile applications. Future targets in reducingCO2-emissions with regard to global warming effects can be met with the help of these engines. A major disadvantage of diesel engines is the high soot and nitrogen oxide emissions which cannot be reduced completely with only engine measures today. The present paper describes two different possibilities for the simultaneous in-cylinder reduction of soot and nitrogen oxide emissions. One possibility is the optimization of the injection process with a new injection strategy the other one is the use of water diesel emulsions with the conventional injection system. The new injection strategy for this experimental part of the study overcomes the problem of increased soot emissions with pilot injection by separating the injections spatially and therefore on the one hand reduces the soot formation during the early stages of the combustion and on the other hand increases the soot oxidation later during the combustion. Another method to reduce the emissions is the introduction of water into the combustion chamber. Emulsions of water and fuel offer the potential to simultaneously reduceNOxand soot emissions while maintaining a high-thermal efficiency. This article presents a theoretical investigation of the use of fuel-water emulsions in DI-Diesel engines. The numerical simulations are carried out with the 3D-CFD code KIVA3V. The use of different water diesel emulsions is investigated and assessed with the numerical model.

The Structure of Laminar Premixed H2-Air Flames at Elevated Pressures

2000 ◽  
Vol 214 (4) ◽  
Author(s):  
M. El-Gamal ◽  
E. Gutheil ◽  
J. Warnatz
Keyword(s):  
Laminar Flame ◽  
Flame Structure ◽  
Ideal Gas ◽  
Fortran Program ◽  
Laminar Flame Speed ◽  
Real Gas ◽  
One Dimensional ◽  
Rocket Propulsion ◽  
Elevated Pressures ◽  
Engine Combustion

In high-pressure flames that occur in many practical combustion devices such as industrial furnaces, rocket propulsion and internal engine combustion, the assumption of an ideal gas is not appropriate. The present paper presents a model that includes modifications of the equation of state, transport and thermodynamic properties. The model is implemented into a Fortran program that was developed to simulate numerically one-dimensional planar premixed flames. The influence of the modifications for the real gas behavior on the laminar flame speed and on flame structure is illustrated for stoichiometric H

RCCI of Synthetic Kerosene With PFI of N-Butanol-Combustion and Emissions Characteristics

2015 ◽  
Author(s):  
Valentin Soloiu ◽  
Martin Muiños ◽  
Tyler Naes ◽  
Spencer Harp ◽  
Marcis Jansons
Keyword(s):  
Thermal Efficiency ◽  
Fuel Injection ◽  
Direct Injection ◽  
Cetane Number ◽  
Engine Performance ◽  
Reactivity Controlled Compression Ignition ◽  
Ultra Low Sulfur Diesel ◽  
Indicated Mean Effective Pressure ◽  
Soot Emissions ◽  
Low Sulfur

In this study, the combustion and emissions characteristics of Reactivity Controlled Compression Ignition (RCCI) obtained by direct injection (DI) of S8 and port fuel injection (PFI) of n-butanol were compared with RCCI of ultra-low sulfur diesel #2 (ULSD#2) and PFI of n-butanol at 6 bar indicated mean effective pressure (IMEP) and 1500 rpm. S8 is a synthetic paraffinic kerosene (C6–C18) developed by Syntroleum and is derived from natural gas. S8 is a Fischer-Tropsch fuel that contains a low aromatic percentage (0.5 vol. %) and has a cetane number of 63 versus 47 of ULSD#2. Baselines of DI conventional diesel combustion (CDC), with 100% ULSD#2 and also DI of S8 were conducted. For both RCCI cases, the mass ratio of DI to PFI was set at 1:1. The ignition delay for the ULSD#2 baseline was found to be 10.9 CAD (1.21 ms) and for S8 was shorter at 10.1 CAD (1.12 ms). In RCCI, the premixed charge combustion has been split into two regions of high temperature heat release, an early one BTDC from ignition of ULSD#2 or S8, and a second stage, ATDC from n-butanol combustion. RCCI with n-butanol increased the NOx because the n-butanol contains 21% oxygen, while S8 alone produced 30% less NOx emissions when compared to the ULSD#2 baseline. The RCCI reduced soot by 80–90% (more efficient for S8). However, S8 alone showed a considerable increase in soot emissions compared with ULSD#2. The indicated thermal efficiency was the highest for the ULSD#2 and S8 baseline at 44%. The RCCI strategies showed a decrease in indicated thermal efficiency at 40% ULSD#2-RCCI and 42% and for S8-RCCI, respectively. S8 as a single fuel proved to be a very capable alternative to ULSD#2 in terms of combustion performance nevertheless, exhibited higher soot emissions that have been mitigated with the RCCI strategy without penalty in engine performance.

scholarly journals Mechanism of Emission Reduction in HSDI Diesel Engine: Split Injection

2015 ◽  
Vol 09 (2) ◽  
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Temporal Distribution ◽  
Reaction Rates ◽  
Chemical Mechanism ◽  
Symmetric Model ◽  
Diesel Combustion ◽  
Split Injection ◽  
Engine Combustion ◽  
Experimental Values

In order to meet the stringent emission standards significant efforts have been imparted to the research and development of cleaner IC engines. Diesel combustion and the formation of pollutants are directly influenced by spatial and temporal distribution of the fuel injected. The development and validation of computational fluid dynamics (CFD) models for diesel engine combustion and emissions is described. The complexity of diesel combustion requires simulation with many complex interacting sub models in order to have a success in improving the performance and to reduce the emissions. In the present work an attempt has been made to develop a multidimensional axe-symmetric model for CI engine combustion and emissions. Later simulations have been carried out using split injection for single, double and three pulses (split injection) for which commercial validation tool FLUENT was used for simulation. The tool solves basic governing equations of fluid flow that is continuity, momentum, species transport and energy equation. Using finite volume method turbulence was modeled by using RNG K-ɛ model. Injection was modeled using La Grangian approach and reaction was modeled using non premixed combustion which considers the effects of turbulence and detailed chemical mechanism into account to model the reaction rates. The specific heats were approximated using piecewise polynomials. Subsequently the simulated results have been validated with the existing experimental values. The peak pressure obtained by simulation for single and double is 10% higher than to that of experimental value. Whereas for triple injections 5% higher than to that of experimental value. For quadruple injection the pressure has been decreased by 10% when compared to triple injection.NOX have been decreased in simulation for single, double and triple injections by 15%, 28% and 20%.For quadruple injection NOX were reduced in quadruple injection by 20% to that of triple injection. The simulated value of soot for single, double and triple injections are 12%, 22% and 12% lesser than the experimental values. For quadruple injection the soot levels were almost negligible. The simulated heat release rates for single, double and triple were reduced by 12%, 18% and 11%. For quadruple injection heat release is reduced same as to that of triple injection.

Combustion and Emission Characteristics of Dual Fuel Engine for Different Parameters

2021 ◽  
Vol 13 (4) ◽  
Author(s):  
Jianjun Zhu ◽  
Peng Li ◽  
Yufeng Xie ◽  
Xin Geng
Keyword(s):  
Diesel Engine ◽  
Heat Release ◽  
Heat Release Rate ◽  
Compression Ratio ◽  
Release Rate ◽  
Emission Characteristics ◽  
Soot Emission ◽  
Cylinder Pressure ◽  
Fuel Delivery ◽  
Soot Emissions

The effects of compression ratio and fuel delivery advance angle on the combustion and emission characteristics of premixed methanol charge induced ignition by Fischer Tropsch diesel engine were investigated using a CY25TQ diesel engine. In the process of reducing the compression ratio from 16.9 to 15.4, the starting point of combustion is fluctuating, the peak of in-cylinder pressure and the maximum pressure increase rate decrease by 44.5% and 37.7% respectively. The peak instantaneous heat release rate increases by 54.4%. HC and CO emissions are on a rising trend. NOx and soot emissions were greatly decreased. The soot emission has the biggest drop of 50%. Reducing the fuel delivery advance angle will make the peak of in-cylinder pressure and the peak of pressure rise rate increase while the peak of heat release rate decreases. The soot emission is negatively correlated with the fuel delivery advance angle. When the fuel delivery advance angle is 16° CA, the soot emissions increased the most by 130%.

Optimization of injection parameters for ethanol blends of plastic oil in VCR engine using RSM and ANN

2021 ◽  
Vol ahead-of-print (ahead-of-print) ◽  
Author(s):  
Datta Bharadwaz Yellapragada ◽  
Govinda Rao Budda ◽  
Kavya Vadavelli
Keyword(s):  
Compression Ratio ◽  
Fuel Injection ◽  
Injection Pressure ◽  
Operating Parameters ◽  
Injection Timing ◽  
Oxides Of Nitrogen ◽  
Operational Parameters ◽  
Content Type ◽  
Injection Parameters ◽  
Ethanol Blends

Purpose The present work aims at improving the performance of the engine using optimized fuel injection strategies and operating parameters for plastic oil ethanol blends. To optimize and predict the engine injection and operational parameters, response surface methodology (RSM) and artificial neural networks (ANN) are used respectively. Design/methodology/approach The engine operating parameters such as load, compression ratio, injection timing and the injection pressure are taken as inputs whereas brake thermal efficiency (BTHE), brake-specific fuel consumption (BSFC), carbon monoxide (CO), hydrocarbons (HC), oxides of nitrogen (NOx) and smoke emissions are treated as outputs. The experiments are designed according to the design of experiments, and optimization is carried out to find the optimum operational and injection parameters for plastic oil ethanol blends in the engine. Findings Optimum operational parameters of the engine when fuelled with plastic oil and ethanol blends are obtained at 8 kg of load, injection pressure of 257 bar, injection timing of 17° before top dead center and blend of 15%. The engine performance parameters obtained at optimum engine running conditions are BTHE 32.5%, BSFC 0.24 kg/kW.h, CO 0.057%, HC 10 ppm, NOx 324.13 ppm and smoke 79.1%. The values predicted from ANN are found to be more close to experimental values when compared with the values of RSM. Originality/value In the present work, a comparative analysis is carried out on the prediction capabilities of ANN and RSM for variable compression ratio engine fuelled with ethanol blends of plastic oil. The error of prediction for ANN is less than 5% for all the responses such as BTHE, BSFC, CO and NOx except for HC emission which is 12.8%.

Sign in / Sign up

Export Citation Format

Share Document