The Effect of the Accommodation Coefficient on Slider Air Bearing Simulation

1999 ◽  
Vol 122 (2) ◽  
pp. 427-435 ◽  
Author(s):  
Weidong Huang ◽  
David B. Bogy
Keyword(s):  
Flow Rate ◽  
Hard Disk Drives ◽  
Direct Simulation Monte Carlo ◽  
Accommodation Coefficient ◽  
Flying Height ◽  
Positive Pressure ◽  
Air Bearing ◽  
Unit Value ◽  
Slider Air Bearing ◽  
Molecular Gas Film Lubrication

In solving the slider air bearing problem, both the Molecular Gas-film Lubrication (MGL) model and the Direct Simulation Monte Carlo (DSMC) model require the accommodation coefficient as input. The accommodation coefficient represents the fraction of the air molecules that interact with solid boundaries in a diffusive manner. In general, the value 1 is used for the accommodation coefficient, which represents a fully diffusive reflection. However, in magnetic hard disk drives, the disk and slider surfaces are becoming ever smoother with different kinds of lubrication on the disk, while the temperature is becoming higher due to the faster spindle speed. Under these conditions the unit value of the accommodation coefficient may no longer be suitable. In order to understand the effect of the accommodation coefficient on the slider’s flying parameters, we used Kang’s new database for the Poiseuille flow rate Qp and Couette flow rate Qc to solve the modified Reynolds equation for two groups of sliders, e.g., negative and positive pressure sliders (“negative” refers to sliders with subambient pressure zones). The results show that, in general, the smaller the accommodation coefficient, the lower the flying height and pitch angle. Positive pressure sliders are more sensitive to the accommodation coefficient than are negative pressure sliders. The typical discrepancy in flying height is around 10%. Also, it is shown that for positive pressure sliders the lower the flying height, the larger the discrepancy percentage. [S0742-4787(00)00402-1]

Optimization of Air Bearing Slider Design

2005 ◽  
Author(s):  
Wending Fang ◽  
Yujuan Wang ◽  
Yunfei Chen
Keyword(s):  
Simulated Annealing ◽  
Simulated Annealing Algorithm ◽  
Optimal Algorithm ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Flying Height ◽  
Air Bearing ◽  
Disk Drives ◽  
Slider Air Bearing ◽  
Bearing Design

Hard disk drives continue to increase the data storage density. The parameters of the head slider flying attitude must satisfy very strict performance goals. This paper focuses on the topic of the simulated annealing algorithm when it is applied to the problem of slider air bearing design in hard disk drives. The objective is to minimize the static flying height, to keep the pitch angle within a reasonable range, and to minimize the roll angle. The design variables include recess depth and geometry configuration of the slider air bearing surface. A typical tri-pad slider was taken as the physical model to demonstrate the validity of the optimal algorithm. Results show that simulated annealing is efficient for the optimization of the slider air bearing design. The static air bearing characteristics were enhanced significantly.

Effect of the Intermolecular Forces on the Flying Attitude of Sub-5 NM Flying Height Air Bearing Sliders in Hard Disk Drives

2002 ◽  
Vol 124 (3) ◽  
pp. 562-567 ◽  
Author(s):  
Lin Wu ◽  
D. B. Bogy
Keyword(s):  
Hard Disk Drives ◽  
Three Dimensional ◽  
Disk Surface ◽  
Intermolecular Forces ◽  
Flying Height ◽  
Positive Pressure ◽  
Vertical Force ◽  
Air Bearing ◽  
Triangular Cell ◽  
Flying Attitude

When the spacing between the slider and the disk is smaller than 10 nm, the effect of the intermolecular forces between the two solid surfaces can no longer be ignored. This effect on the flying attitude of practical slider designs is investigated here numerically. The three-dimensional slider surface is discretized into non-overlapping unstructured triangles. The intermolecular forces between each triangular cell of the slider and the disk surface are formulated, and their contributions to the total vertical force, as well as the pitch and roll moments, are included in a previously developed steady state air bearing design code based on a multi-grid finite volume method with unstructured triangular grids [3–5]. It is found that the van der Waals force has significant influence on the flying height and has non-negligible effect on the pitch angle for both positive pressure sliders and negative pressure sliders, when the flying height is below 5 nm. When the flying height is below 0.5 nm, the repulsive portion of the intermolecular force becomes important and also has to be included.

An Asperity Contact Model for the Slider Air Bearing

1999 ◽  
Vol 122 (2) ◽  
pp. 436-443 ◽  
Author(s):  
Weidong Huang ◽  
David B. Bogy ◽  
Masayuki Honchi
Keyword(s):  
Direct Simulation Monte Carlo ◽  
Flying Height ◽  
Asperity Contact ◽  
Air Bearing ◽  
Single Asperity ◽  
Bearing Force ◽  
Single Asperity Contact ◽  
Molecular Gas Film Lubrication ◽  
Flying Attitude ◽  
Film Lubrication

As sliders fly closer and closer to the disks, asperity contact is inevitable due to the roughness on the sliders and the disks. A single asperity contact problem was solved using the molecular gas-film lubrication (MGL) model with the no-fly-zone (NFZ) condition, which was discovered with the direct simulation Monte Carlo method (DSMC). It shows that the MGL model can also provide bounded pressure and resultant force in the presence of contact. Moreover, the MGL results agree well with the DSMC results. A database for a single asperity contact force and moment was then created using the MGL model with the NFZ condition. This force and moment was superimposed to the air bearing force calculated by the MGL model calculated by the MGL model when the nominal plane of the slider and the disk are not in contact. The total additional air bearing force due to asperity contact was obtained. Its effect on the slider’s flying attitude was investigated and found to change the flying height and pitch angle up to 20 percent and 10 percent, respectively. [S0742-4787(00)02402-4]

Performance of Sliders Flying Over Discrete-Track Media

2007 ◽  
Vol 129 (4) ◽  
pp. 712-719 ◽  
Author(s):  
Jianhua Li ◽  
Junguo Xu ◽  
Yuki Shimizu
Keyword(s):  
Estimation Method ◽  
Simulation Method ◽  
Measured Data ◽  
Flying Height ◽  
Height Loss ◽  
Air Bearing ◽  
Slider Air Bearing ◽  
Discrete Track ◽  
Flying Attitude ◽  
Manufacturing Variation

A simulation method in which grooves are virtually distributed on the slider air bearing instead of on the grooved medium surface has been developed and used to investigate the performance of sliders flying over the surface of a discrete-track medium. The simulated flying height loss due to a discrete-track medium coincides well with the measured data, whereas the average-estimation method overestimates flying height loss. Among the characteristics of a slider flying over the surface of a discrete-track medium that were studied are the flying attitude, the effect of groove parameters on flying profile, and the flying height losses due to manufacturing variation and altitude. The results indicate that when a slider is flying over the surface of a discrete-track medium, it will have a higher 3σ of flying height, be more sensitive to altitude, and will have a greater flying height loss.

Effect of Intermolecular Forces on the Static and Dynamic Performance of Air Bearing Sliders: Part II—Dependence of the Stability on Hamaker Constant, Suspension Preload and Pitch Angle

2005 ◽  
Vol 128 (1) ◽  
pp. 203-208 ◽  
Author(s):  
Vineet Gupta ◽  
David B. Bogy
Keyword(s):  
Pitch Angle ◽  
Dynamic Performance ◽  
Hard Disk Drives ◽  
Intermolecular Forces ◽  
Flying Height ◽  
Total Force ◽  
Air Bearing ◽  
Force Increase ◽  
The Stability ◽  
Fly Height

Intermolecular and surface forces contribute significantly to the total forces acting on air bearing sliders for flying heights below 5 nm. Their contributions to the total force increase sharply with the reduction in flying height, and hence their existence can no longer be ignored in air bearing simulation for hard disk drives. Various experimentally observed dynamic instabilities can be explained by the inclusion of these forces in the model for low flying sliders. In this paper parametric studies are presented using a 3-DOF model to better understand the effect of the Hamaker constants, suspension pre load and pitch angle on the dynamic stability/instability of the sliders. A stiffness matrix is used to characterize the stability in the vertical, pitch, and roll directions. The fly height diagrams are used to examine the multiple equilibriums that exist for low flying heights. It has been found that the system instability increases as the magnitude of the van der Waals force increases. It has also been found that higher suspension pre load and higher pitch angles tend to stabilize the system.

Design and Dynamics of Flying Height Control Slider With Piezoelectric Nanoactuator in Hard Disk Drives

2006 ◽  
Vol 129 (1) ◽  
pp. 161-170 ◽  
Author(s):  
Jia-Yang Juang ◽  
David B. Bogy ◽  
C. Singh Bhatia
Keyword(s):  
Numerical Study ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Areal Density ◽  
Flying Height ◽  
Air Bearing ◽  
Disk Drives ◽  
Adhesion Forces ◽  
Surface Design ◽  
Ultrahigh Density

To achieve the areal density goal in hard disk drives of 1Tbit∕in.2 the minimum physical spacing or flying height (FH) between the read/write element and disk must be reduced to ∼2nm. A brief review of several FH adjustment schemes is first presented and discussed. Previous research showed that the actuation efficiency (defined as the ratio of the FH reduction to the stroke) was low due to the significant air bearing coupling. In this paper, an air bearing surface design, Slider B, for a FH control slider with a piezoelectric nanoactuator is proposed to achieve virtually 100% efficiency and to increase dynamics stability by minimizing the nanoscale adhesion forces. A numerical study was conducted to investigate both the static and dynamic performances of the Slider B, such as uniformity of gap FH with near-zero roll over the entire disk, ultrahigh roll stiffness and damping, low nanoscale adhesion forces, uniform FH track-seeking motion, dynamic load/unload, and FH modulation. Slider B was found to exhibit an overall enhancement in performance, stability, and reliability in ultrahigh density magnetic recording.

Air Bearing Pushback in Heat Assisted Magnetic Recording

2019 ◽  
Author(s):  
Shaomin Xiong ◽  
Robert Smith ◽  
Chanh Nguyen ◽  
Youfeng Zhang ◽  
Yeoungchin Yoon
Keyword(s):  
Magnetic Recording ◽  
Hard Disk Drives ◽  
Hard Disk ◽  
Disk Drive ◽  
Flying Height ◽  
Air Bearing ◽  
Magnetic Media ◽  
Heat Assisted Magnetic Recording ◽  
Height Control ◽  
Different Dimensions

Abstract The air bearing surface is critical to the spacing control in current hard disk drives (HDDs). Thermal protrusions, including thermal flying height control (TFC) and writer coil protrusion, drive the reader/writer elements closer to the magnetic media. The spacing control actuation efficiency depends on the air bearing push back response after the TFC or writer protrudes. In the next generation hard disk drive technology, heat assisted magnetic recording (HAMR), laser induced protrusions further complicate the spacing control. The laser induced protrusions, such as the localized NFT protrusion and a wider change of the crown and camber, have very different dimensions and transient characteristics than the traditional TFC and writer protrusion. The dimension of the NFT protrusion is relatively smaller, and the transient is much faster than the TFC protrusion. However, it is found that the NFT protrusion is large enough to generate an air bearing push back effect, which changes the read and write spacing when the laser is powered on. To accurately control spacing in HAMR, this push back effect has to be taken into account.

Sign in / Sign up

Export Citation Format

Share Document