Quantitative Visualization of the Flow in a Centrifugal Pump With Diffuser Vanes—II: Addressing Passage-Averaged and Large-Eddy Simulation Modeling Issues in Turbomachinery Flows

1999 ◽  
Vol 122 (1) ◽  
pp. 108-116 ◽  
Author(s):  
Manish Sinha ◽  
Joseph Katz ◽  
Charles Meneveau
Keyword(s):  
Large Eddy Simulation ◽  
Centrifugal Pump ◽  
Particle Image Velocimetry Data ◽  
Navier Stokes ◽  
Reynolds Stresses ◽  
Vaned Diffuser ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Quantitative Visualization ◽  
The Difference

The present paper addresses two basic modeling problems of the flow in turbomachines. For simulation of flows within multistage turbomachinery, unsteady Reynolds-averaged Navier–Stokes (RANS) of an entire series of blade rows is typically impractical. On the other hand, when performing RANS of each blade row separately one is faced with major difficulties in matching boundary conditions. A popular remedy is the “passage-averaged” approach. Unsteady effects caused by neighboring rows are averaged out over all blade orientations, but are accounted for through “deterministic” stresses, which must be modeled. To experimentally study modeling issues for deterministic stresses we use particle image velocimetry data of the flow in a centrifugal pump with a vaned diffuser that includes the flow in the impeller, the gap between the impeller and diffuser, between the diffuser vanes and within the volute downstream. The data have been presented in part A of this paper (Sinha and Katz, 1998, “Flow Structure and Turbulence of a Centrifugal Pump with a Vaned Diffuser,” Proceedings of the ASME Fluids Engineering Division, Washington, DC). Deterministic stresses are obtained from the difference between the phase-averaged and passage-averaged data, whereas the Reynolds stresses are determined from the difference between the instantaneous and phase averaged data. In agreement with previous findings, the deterministic stresses are larger than the Reynolds stresses in regions close to the interface between blade rows, and thus must be carefully accounted for in passage-averaged simulations. The Reynolds stresses are larger in regions located far from the transition region. The second series of issues involves modeling for large-eddy simulation. The measured subgrid stresses determined by spatially filtering the data are compared to eddy viscosity models and show significant discrepancies, especially in regions with separating shear layers. Backscatter of energy that persists during phase averaging is also observed. [S0098-2202(00)00901-9]

scholarly journals Investigation of flow separation in a centrifugal pump impeller based on improved delayed detached eddy simulation method

2019 ◽  
Vol 11 (12) ◽  
pp. 168781401989783
Author(s):  
Yun Ren ◽  
Zuchao Zhu ◽  
Denghao Wu ◽  
Xiaojun Li ◽  
Lanfang Jiang
Keyword(s):  
Large Eddy Simulation ◽  
Centrifugal Pump ◽  
Flow Separation ◽  
Hybrid Algorithm ◽  
Internal Flow ◽  
Navier Stokes ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes ◽  
Vorticity Flux

The mechanism of flow separation in the impeller of a centrifugal pump with a low specific speed was explored by experimental, numerical, and theoretical methods. A novel delayed Reynolds-averaged Navier–Stokes/large eddy simulation hybrid algorithm combined with a rotation and curvature correction method was developed to calculate the inner flow field of the original pump for the large friction loss in the centrifugal impeller, high adverse pressure gradient, and large blade curvature. Boundary vorticity flux theory was introduced for internal flow diagnosis, and the relative velocity vector near the surface of the blade and the distribution of the dimensionless pressure coefficient was analyzed. The validity of the numerical method was verified, and the location of the backflow area and its flow features were determined. Finally, based on flow diagnosis, the geometric parameters influencing the flow state of the impeller were specifically adjusted to obtain a new design impeller. The results showed that the distribution of the boundary vorticity flux peak values, the skin friction streamline, and near-wall relative velocities improved significantly after the design change. In addition, the flow separation was delayed, the force applied on the blade was improved, the head under the part-load condition was improved, and the hydraulic efficiency was improved over the global flow ranges. It was demonstrated that the delayed Reynolds-averaged Navier–Stokes/large eddy simulation hybrid algorithm was capable to capture the separation flow in a centrifugal pump, and the boundary vorticity flux theory was suitable for the internal flow diagnosis of centrifugal pump.

scholarly journals Large Eddy Simulation of Periodic Transient Pressure Fluctuation in a Centrifugal Pump Impeller at Low Flow Rate

Symmetry ◽  
2021 ◽  
Vol 13 (2) ◽  
pp. 311
Author(s):  
Renfei Kuang ◽  
Xiaoping Chen ◽  
Zhiming Zhang ◽  
Zuchao Zhu ◽  
Yu Li
Keyword(s):  
Large Eddy Simulation ◽  
Centrifugal Pump ◽  
Flow Rate ◽  
Pressure Fluctuation ◽  
Low Frequency ◽  
Pump Impeller ◽  
Eddy Simulation ◽  
Inlet Flow Rate ◽  
Large Eddy ◽  
Centrifugal Pump Impeller

This paper presents a large eddy simulation of a centrifugal pump impeller during a transient condition. The flow rate is sinusoidal and oscillates between 0.25Qd (Qd indicates design load) and 0.75Qd when the rotating speed is maintained. Research shows that in one period, the inlet flow rate will twice reach 0.5Qd, and among the impeller of one moment is a stall state, but the other is a non-stall state. In the process of flow development, the evolution of low-frequency pressure fluctuation shows an obviously sinusoidal form, whose frequency is insensitive to the monitoring position and equals to that of the flow rate. However, inside the impeller, the phase and amplitude in the stall passages lag behind more and are stronger than that in the non-stall passages. Meanwhile, the strongest region of the high-frequency pressure fluctuation appears in the stall passages at the transient rising stage. The second dominant frequency in stall passages is 2.5 times to that in non-stall passages. In addition, similar to the pressure fluctuation, the evolution of the low-frequency head shows a sinusoidal form, whose phase is lagging behind that by one-third of a period in the inlet flow rate.

Hybrid Large Eddy Simulation/Reynolds-Averaged Navier–Stokes Analysis of a Premixed Ethylene-Fueled Dual-Mode Scramjet Combustor

AIAA Journal ◽  
2021 ◽  
pp. 1-17
Author(s):  
Tanner B. Nielsen ◽  
Jack R. Edwards ◽  
Harsha K. Chelliah ◽  
Damien Lieber ◽  
Clayton Geipel ◽  
...  
Keyword(s):  
Large Eddy Simulation ◽  
Navier Stokes ◽  
Dual Mode ◽  
Eddy Simulation ◽  
Scramjet Combustor ◽  
Large Eddy ◽  
Reynolds Averaged Navier Stokes

Simulation of Vortex Instability in a Pipe Trifurcation

2003 ◽  
Author(s):  
Albert Ruprecht ◽  
Ralf Neubauer ◽  
Thomas Helmrich
Keyword(s):  
Large Eddy Simulation ◽  
Turbulence Model ◽  
Model Test ◽  
Reasonable Agreement ◽  
Navier Stokes ◽  
Extended Version ◽  
Vortex Instability ◽  
Flow Phenomenon ◽  
Eddy Simulation ◽  
Large Eddy

The vortex instability in a spherical pipe trifurcation is investigated by applying a Very Large Eddy Simulation (VLES). For this approach an new adaptive turbulence model based on an extended version of the k-ε model is used. Applying a classical Reynolds-averaged Navier-Stokes-Simulation with the standard k-ε model is not able to forecast the vortex instability. However the prescribed VLES method is capable to predict this flow phenomenon. The obtained results show a reasonable agreement with measurements in a model test.

Large Eddy Simulation of Cross Flow in Pipe Junction

2018 ◽  
Author(s):  
Jiajun Chen ◽  
Yue Sun ◽  
Hang Zhang ◽  
Dakui Feng ◽  
Zhiguo Zhang
Keyword(s):  
Large Eddy Simulation ◽  
Stokes Equations ◽  
Numerical Study ◽  
Three Dimensional ◽  
Cross Flow ◽  
Exciting Force ◽  
Navier Stokes ◽  
Pipe Network ◽  
Eddy Simulation ◽  
Large Eddy

Mixing in pipe junctions can play an important role in exciting force and distribution of flow in pipe network. This paper investigated the cross pipe junction and proposed an improved plan, Y-shaped pipe junction. The numerical study of a three-dimensional pipe junction was performed for calculation and improved understanding of flow feature in pipe. The filtered Navier–Stokes equations were used to perform the large-eddy simulation of the unsteady incompressible flow in pipe. From the analysis of these results, it clearly appears that the vortex strength and velocity non-uniformity of centerline, can be reduced by Y-shaped junction. The Y-shaped junction not only has better flow characteristic, but also reduces head loss and exciting force. The results of the three-dimensional improvement analysis of junction can be used in the design of pipe network for industry.

Large Eddy Simulation of the Flow Around a Diffuser-Equipped Bluff Body in Ground Effect

2011 ◽  
Author(s):  
Lara Schembri Puglisevich ◽  
Gary Page
Keyword(s):  
Large Eddy Simulation ◽  
Bluff Body ◽  
Vortex Formation ◽  
Ground Effect ◽  
Vortical Flow ◽  
Navier Stokes ◽  
Flow Structures ◽  
Eddy Simulation ◽  
Large Eddy ◽  
Flow Features

Unsteady Large Eddy Simulation (LES) is carried out for the flow around a bluff body equipped with an underbody rear diffuser in close proximity to the ground, representing an automotive diffuser. The goal is to demonstrate the ability of LES to model underbody vortical flow features at experimental Reynolds numbers (1.01 × 106 based on model height and incoming velocity). The scope of the time-dependent simulations is not to improve on Reynolds-Averaged Navier Stokes (RANS), but to give further insight into vortex formation and progression, allowing better understanding of the flow, hence allowing more control. Vortical flow structures in the diffuser region, along the sides and top surface of the bluff body are successfully modelled. Differences between instantaneous and time-averaged flow structures are presented and explained. Comparisons to pressure measurements from wind tunnel experiments on an identical bluff body model shows a good level of agreement.

Sign in / Sign up

Export Citation Format

Share Document