Stabilization of a Translating Tensioned Beam Through a Pointwise Control Force

1998 ◽  
Vol 122 (2) ◽  
pp. 322-331 ◽  
Author(s):  
W. D. Zhu ◽  
B. Z. Guo ◽  
C. D. Mote,

A spectral analysis determining asymptotically the distribution of eigenvalues of a constrained, translating, tensioned beam in closed form is the subject of this paper. The constraint is modeled by a spring-mass-dashpot subsystem that is located at any position within the span of the beam. It can represent a feedback controller with a collocated sensor and actuator. The necessary and sufficient condition that ensures a uniform stability margin for all the modes of vibration is determined. Influences of system parameters on the distribution of eigenvalues are identified. The analytical predictions are validated by numerical analyses. The constraint location maximizing the stability margin of the distributed model is predicted through a combined analytical and numerical approach. The implications and utility of the results are illustrated. The methodology developed can be extended to predict stability margins and optimize control parameters for controlled translating beams with other types of boundary conditions and controller structures. [S0022-0434(00)00702-4]

Author(s):  
Jose March-Leuba ◽  
Weidong Wang ◽  
Tai L. Huang

Cores loaded with a mixture of fuel types are known to reduce stability margins. Mixed fuel cores have become more common as utilities change fuel suppliers, or when fuel vendors upgrade their fuel designs to take advantage of improved thermal and mechanical margins. This paper studies some of the physical processes that reduce the stability of mixed cores. A number of runs have been performed using the LAPUR6 stability code to evaluate the effect on mixed cores on the stability of a typical BWR. To this end, two fuel types have been set up with two different single-phase to two-phase pressure drop ratios by artificially adjusting the spacer and inlet orifice friction coefficients. The flow and pressure drop characteristics of both fuels have been matched at full flow, full power conditions. All manufacturers match the pressure drop of new fuels so that the flow distributions among the new and old fuel elements operating at the same power are approximately constant. The critical power ratio and thermo-mechanical criteria are typically limiting at full power; therefore matching the flow performance at full power maximizes the margin to these criteria. Stability is of concern at low flows, especially at natural circulation, where the thermal-hydraulic conditions are significantly different from full flow and power. Our simulations show that even if two fuel elements are perfectly matched at full flow, the axial void fraction distribution changes significantly when the flow is reduced to natural circulation conditions and the two fuel elements are not fully thermal-hydraulically compatible at the reduced flows. Basically, the two fuel types set up two separate natural circulation lines, and one of the fuel types essentially starves the other from flow. Since stability has such a strong dependence with channel flow, the reactor stability is controlled by the fuel type that has the smaller flow at natural circulation. A counterintuitive result of this study shows that, in general, loading a more stable fuel type into a mixed core has the opposite effect, and the stability margin of that mixed core is lower until the new, more stable fuel becomes dominant. Because of the burnable Gadolinium in most modern BWR fuels, the highest reactivity fuel elements are the once-burned. Loading a more stable fuel type starves the flow of the high-reactivity older fuel, reducing the stability margin.


Energies ◽  
2020 ◽  
Vol 13 (10) ◽  
pp. 2663
Author(s):  
Isaías V. de Bessa ◽  
Renan L. P. de Medeiros ◽  
Iury Bessa ◽  
Florindo A. C. Ayres Junior ◽  
Alessandra R. de Menezes ◽  
...  

The DC microgrid system is composed by converters that operate like feeders and loads. Among these loads, we highlight the constant power loads (CPLs) that may cause instability in the microgrid, observed in the form of undesired oscillations due to its negative impedance behavior. Therefore, this work proposes to use performance indices and stability margins to evaluate state and output feedback control strategies for stabilization of DC microgrids. In particular, it is proposed to evaluate the stability margin of the proposed methodologies by means of the impedance relations in the microgrid based on the Middlebrook criterion. Our simulations and tests showed the relation between the performance and stability degradation and the microgrid impedances variation.


1975 ◽  
Vol 97 (4) ◽  
pp. 477-483 ◽  
Author(s):  
M. P. Boyce ◽  
R. N. Schiller ◽  
A. R. Desai

The phenomenon of surge in an axial flow compressor has long eluded the analytical fluid dynamist. In the recent years, a growing degree of improvement and sophistication in the design of axial flow compressors to achieve higher pressure ratios has resulted in increasingly narrow domains of stable operation. A search for improving stability margins revealed the importance of the blade tip region and casing treatments. The authors have approached the problem by both experimental and analytical methods. The results are mutually confirming. Important new inroads have been made in understanding the flow in the blade tip region, operation of casing treatments and the mechanism of the onset of surge. Some significant conclusions in the selection and design of casing treatments and their effects on the stability margin are presented and explained on the basis of experimental and theoretical results.


Author(s):  
Kaveh Nazem Tahmasebi ◽  
Roberto Belotti ◽  
Renato Vidoni ◽  
Karl Von Ellenrieder

Abstract The tip-over instability of an autonomous mobile robot is a significant problem as it can diminish its maneuverability and increase the possibility of damaging the robot and its surrounding environment. For these reasons, it is important to define the stability margin and predict the edge of the tip-over instability considering different robot specifications and environmental conditions. Different stability measures have been developed to evaluate and analyze robot stability margins for diverse conditions. In this work, the Zero Moment Point, Energy Stability Margin, Force-Angle Stability Measure, and Mass-Moment Height Stability Measure methods are considered and applied to different mobile robot architectures including three-wheeled, four-wheeled (with rectangular and trapezoidal base surface) and articulated systems. The stability margins are discussed considering the four different stability criteria and evaluating the effect of a sloped surface. Then, the sensitivity of the tip-over instability in relation to the variation of the center of mass height as an important robot configuration parameter is evaluated. Finally, after a theoretical extension of the Force-Angle Stability and Mass-Moment Height stability measurement methods, the articulated mobile robot’s stability margin is considered and evaluated.


2016 ◽  
Vol 32 ◽  
Author(s):  
Kuo-Yang Tu ◽  
Cheng-Hsiung Huang ◽  
Jacky Baltes

AbstractUsually, humanoid walking gaits are only roughly distinguished between stable and unstable. The evaluation of a stable humanoid walking gait is difficult to quantify in scales. And, it is extremely hard to adjust humanoid robots in suitable a walking gait for different movement objectives such as fast walking, uneven floor walking, and so on. This paper proposes a stability margin constructed by center of pressure (COP) to evaluate the gait stability of humanoid walking. The stability margin is modeled by the COP regions that a humanoid robot needs for stable standing. We derive the mathematical model for COP position by dividing the walking gait into single and double support phases in order to measure the stability of the COP regions. An actual measuring system for the stable COP regions is designed and implemented. The measured COP trajectory of a walking gait is eventually evaluated with respect to the stable COP regions for the stability margins. The evaluation focuses on weak stability areas to be improved for robust walking gaits. To demonstrate the robustness of the improved walking gait, we replicate the experiment on three different terrains. The experiments demonstrate that the walking gaits developed based on stable COP region can be applied for different movement objectives.


Complexity ◽  
2020 ◽  
Vol 2020 ◽  
pp. 1-10
Author(s):  
Xunxun Zhang ◽  
Li Li ◽  
Xu Zhu

Due to the limited band width and congestion of communication channels in the wireless vehicle-to-vehicle (V2V) communication, time delay inevitably arises and dramatically leads to the disturbances for the automated vehicular platoon. This paper focuses on computing the exact time delay stability margin. In this study, we treat this problem as a stability issue of a consensus system with time delay, where each vehicle in the platoon is recognized as a node, and the interconnected information flow is represented as a graph. Then, the distributed controller is designed by combining the states of the vehicle itself and its neighbouring vehicles. Furthermore, the stability of the entire platoon is analysed according to the characteristic equation of the closed-loop system, and a necessary and sufficient condition for the exact time delay stability margin is obtained. Especially, for the automated vehicular platoon with undirected topology, it is revealed that exact time delay stability margin is determined by the largest eigenvalue of the augmented Laplacian matrix. Furthermore, a rapid method for finding exact time delay stability margin is proposed. Finally, numerical simulations demonstrate that this work generates exact and satisfactory time delay stability margin for the automated vehicular platoon.


2003 ◽  
pp. 88-98 ◽  
Author(s):  
A. Obydenov

Self-regulation appears to be a special institution where economic actors establish their own rules of economic activity for themselves in a specific business field. At the same time they are the object of control within these rules and the subject of legal management of the controller. Self-regulation contains necessary prerequisites for fundamental resolution of the problem of "controlling the controller". The necessary and sufficient set of five self-regulation organization functions provides efficiency of self-regulation as the institutional arrangement. The voluntary membership in a self-regulation organization is essential for ensuring self-enforcement of institutional arrangement of self-regulation.


The theory of the vibrations of the pianoforte string put forward by Kaufmann in a well-known paper has figured prominently in recent discussions on the acoustics of this instrument. It proceeds on lines radically different from those adopted by Helmholtz in his classical treatment of the subject. While recognising that the elasticity of the pianoforte hammer is not a negligible factor, Kaufmann set out to simplify the mathematical analysis by ignoring its effect altogether, and treating the hammer as a particle possessing only inertia without spring. The motion of the string following the impact of the hammer is found from the initial conditions and from the functional solutions of the equation of wave-propagation on the string. On this basis he gave a rigorous treatment of two cases: (1) a particle impinging on a stretched string of infinite length, and (2) a particle impinging on the centre of a finite string, neither of which cases is of much interest from an acoustical point of view. The case of practical importance treated by him is that in which a particle impinges on the string near one end. For this case, he gave only an approximate theory from which the duration of contact, the motion of the point struck, and the form of the vibration-curves for various points of the string could be found. There can be no doubt of the importance of Kaufmann’s work, and it naturally becomes necessary to extend and revise his theory in various directions. In several respects, the theory awaits fuller development, especially as regards the harmonic analysis of the modes of vibration set up by impact, and the detailed discussion of the influence of the elasticity of the hammer and of varying velocities of impact. Apart from these points, the question arises whether the approximate method used by Kaufmann is sufficiently accurate for practical purposes, and whether it may be regarded as applicable when, as in the pianoforte, the point struck is distant one-eighth or one-ninth of the length of the string from one end. Kaufmann’s treatment is practically based on the assumption that the part of the string between the end and the point struck remains straight as long as the hammer and string remain in contact. Primâ facie , it is clear that this assumption would introduce error when the part of the string under reference is an appreciable fraction of the whole. For the effect of the impact would obviously be to excite the vibrations of this portion of the string, which continue so long as the hammer is in contact, and would also influence the mode of vibration of the string as a whole when the hammer loses contact. A mathematical theory which is not subject to this error, and which is applicable for any position of the striking point, thus seems called for.


2020 ◽  
Vol 2020 (1) ◽  
Author(s):  
N. H. Sweilam ◽  
S. M. Al-Mekhlafi ◽  
A. O. Albalawi ◽  
D. Baleanu

Abstract In this paper, a novel coronavirus (2019-nCov) mathematical model with modified parameters is presented. This model consists of six nonlinear fractional order differential equations. Optimal control of the suggested model is the main objective of this work. Two control variables are presented in this model to minimize the population number of infected and asymptotically infected people. Necessary optimality conditions are derived. The Grünwald–Letnikov nonstandard weighted average finite difference method is constructed for simulating the proposed optimal control system. The stability of the proposed method is proved. In order to validate the theoretical results, numerical simulations and comparative studies are given.


2009 ◽  
Vol 16 (4) ◽  
pp. 597-616
Author(s):  
Shota Akhalaia ◽  
Malkhaz Ashordia ◽  
Nestan Kekelia

Abstract Necessary and sufficient conditions are established for the stability in the Lyapunov sense of solutions of a linear system of generalized ordinary differential equations 𝑑𝑥(𝑡) = 𝑑𝐴(𝑡) · 𝑥(𝑡) + 𝑑𝑓(𝑡), where and are, respectively, matrix- and vector-functions with bounded total variation components on every closed interval from . The results are realized for the linear systems of impulsive, ordinary differential and difference equations.


Sign in / Sign up

Export Citation Format

Share Document