Investigation of parameters affecting rotary engine by means of one zone thermodynamic model

2021 ◽  
pp. 1-34
Author(s):  
Osman Akin Kutlar ◽  
Ömer Cihan
Keyword(s):  
Heat Transfer ◽  
Thermodynamic Model ◽  
Fuel Injection ◽  
Combustion Process ◽  
Combustion Products ◽  
Chamber Pressure ◽  
Intake Port ◽  
Model Calculations ◽  
Rotary Engine ◽  
Combustion Duration

Abstract The scope of this work was to establish a one zone thermodynamic calculation model to analyze 13B multi side port (MSP) rotary engine on the base of Mazda RX-8. Volume variation was calculated according to the basic geometrical data of the engine and heat transfer was calculated by using the Wilmer's heat transfer coefficient. Combustion process was defined as heat addition according to Vibe function and simultaneously converting fresh charge to combustion products. To account related losses discharge drag, leakage, crevice volumes and mean friction pressure were taken into account. The port fuel injection (homogeneous mixture) was used in the model assumptions. Model calculations were validated with experimental data. Many parameters were investigated in the model such as combustion chamber pressure, mass and engine torque at different speeds and full load conditions. Moreover, the effect of the Vibe parameter, combustion duration and intake port variations on the torque were investigated. The highest torque value was observed in the model with only primary intake port at low rpm (1000 - 3750 rpm), primary and secondary port at mid rpm (3750 - 6250 rpm). Higher torque values were obtained from two secondary and two auxiliaries than primary, secondary and auxiliary in the literature at high rpm (6250 - 8500 rpm). Combustion duration, Vibe parameter and variations of different intake ports has a significant effect on the engine characteristics. The thermodynamic model developed in this study may be used as an effective tool to examine the performance parameters of the Wankel engine.

scholarly journals Performance, Efficiency and Emissions Evaluation of Gasoline Port-Fuel Injection, Natural Gas Direct Injection and Blended Operation

2016 ◽  
Author(s):  
Michael Pamminger ◽  
Thomas Wallner ◽  
James Sevik ◽  
Riccardo Scarcelli ◽  
Carrie Hall ◽  
...  
Keyword(s):  
Natural Gas ◽  
Internal Combustion Engines ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Process ◽  
Internal Combustion ◽  
Intake Port ◽  
Combustion Engines ◽  
Part Load ◽  
Port Fuel Injection

The need to further reduce fuel consumption and decrease the output of emissions — in order to be within future emissions legislation — is still an ongoing effort for the development of internal combustion engines. Natural gas is a fossil fuel which is comprised mostly of methane and makes it very attractive for use in internal combustion engines because of its higher knock resistance and higher molar hydrogen-to-carbon ratio compared to gasoline. The current paper compares the combustion and emissions behavior of the test engine being operated on either a representative U.S. market gasoline or natural gas. Moreover, specific in-cylinder blend ratios with gasoline and natural gas were also investigated at part-load and wide open throttle conditions. The dilution tolerance for part-load operation was investigated by adding cooled exhaust gas recirculation. The engine used for these investigations was a single cylinder research engine for light duty application which is equipped with two separate fuel systems. Gasoline was injected into the intake port; natural gas was injected directly into the cylinder to overcome the power density loss usually connected with port fuel injection of natural gas. Injecting natural gas directly into the cylinder reduced both ignition delay and combustion duration of the combustion process compared to the injection of gasoline into the intake port. Injecting natural gas and gasoline simultaneously resulted in a higher dilution tolerance compared to operation on one of the fuels alone. Significantly higher net indicated mean effective pressure and indicated thermal efficiency were achieved when natural gas was directly injected after intake valve closing at wide open throttle, compared to an injection while the intake valves were still open. In general it was shown that the blend ratio and the start of injection need to be varied depending on load and dilution level in order to operate the engine with the highest efficiency or highest load.

scholarly journals Simulation Of Natural Gas Combustion Process Using Pressure Based Solver

2016 ◽  
Vol 12 (12) ◽  
pp. 81
Author(s):  
Osama H. Ghazal
Keyword(s):  
Heat Transfer ◽  
Natural Gas ◽  
Fuel Injection ◽  
Combustion Process ◽  
Heat Transfer Process ◽  
Si Engine ◽  
Ic Engine ◽  
Gas Combustion ◽  
Engine Efficiency ◽  
Transfer Models

The aim of this research is to simulate the combustion process for methane using different heat transfer models combined with various fuel injection techniques to better understand the combustion process and heat transfer process inside IC engine which reflect on the engine efficiency. The simulation has been carried out using Lotus Engineering software. This model solves the nonlinear momentum and continuity equations to satisfy the conservation of mass and the conservation of momentum laws. In this analysis a single cylinder four stroke SI engine has been simulated. The fuel used in the simulation is methane. Two fuel systems have been investigated port injection and direct injection. The Wiebe heat release curve has been used. Two widely used for SI engines heat transfer models presented in the simulation, Annand and Woschni. The intension in this paper is to study the effect of various fuel systems and heat transfer models on engine efficiency for different engine speeds. Moreover, the evaluation of the heat transfer models for natural gas SI engine will be tested. Brake power, mean effective pressure, specific fuel consumption, brake thermal efficiency, and heat transfer rate were calculated and discussed to show the effect of varying heat transfer models and fuel systems on engine efficiency.

scholarly journals Modelling of the formulated solid rocket propellant characteristics

2021 ◽  
Vol 6 (2) ◽  
pp. 061-073
Author(s):  
Oyedeko K.F.K ◽  
Egwenu S. O.
Keyword(s):  
Mathematical Model ◽  
Combustion Temperature ◽  
Specific Impulse ◽  
Combustion Process ◽  
General Rule ◽  
Combustion Products ◽  
Potassium Nitrate ◽  
Chamber Pressure ◽  
Performance Parameters ◽  
Solid Rocket

This study is a mathematical model to obtain the characteristics performance of magnesium metal (powder) and carbon on a potassium nitrate-sucrose (KNSU) solid propellant formulation. Characterization of propellant is, as a general rule, important to determine its performance before it can be suitable for use for a rocket flight or any mission. Method of ballistic load cell evaluation was used to validate results and a mathematical model using the combustion exhaust products was solved to obtain the characteristics performance parameters of the propellant. The carbon constituent which acts as an opacifier and coolant was kept constant at 2% in order to arrest some of the heat during the combustion process and helped to lower the combustion temperature, because high combustion temperature could lead to combustion chamber rupture or failure. The effect of addition of magnesium which was optimized for 3% in the formulation contributed significantly in improving the overall performance of the propellant. The utilization of magnesium in KNSU propellant provided higher values parameters and better performance compared to when not included. This was confirmed with the model equations. The propellant combustion products equation was used to model and obtain the characteristics performance parameters. This gave propellant specific impulse (122.9s), combustion temperature (1821K), heat ratio (1.1592), molecular weight (36.89g/mole), propellant density (1912.5kg/m3) and characteristics velocity (1000m/s) result while maintaining the same chamber pressure.

scholarly journals Detailed Injection Strategy Analysis of a Heavy-Duty Diesel Engine Running on Rape Methyl Ester

Energies ◽  
2021 ◽  
Vol 14 (13) ◽  
pp. 3717
Author(s):  
Nikita Zuev ◽  
Andrey Kozlov ◽  
Alexey Terenchenko ◽  
Kirill Karpukhin ◽  
Ulugbek Azimov
Keyword(s):  
Fuel Injection ◽  
Combustion Process ◽  
Pressure Rise ◽  
Base Case ◽  
Biodiesel Fuel ◽  
Pilot Injection ◽  
Post Injection ◽  
Heavy Duty ◽  
Injection Strategy ◽  
Fuel Mass

Using biodiesel fuel in diesel engines for heavy-duty transport is important to meet the stringent emission regulations. Biodiesel is an oxygenated fuel and its physical and chemical properties are close to diesel fuel, yet there is still a need to analyze and tune the fuel injection parameters to optimize the combustion process and emissions. A four-injections strategy was used: two pilots, one main and one post injection. A highly advanced SOI decreases the NOx and the compression work but makes the combustion process less efficient. The pilot injection fuel mass influences the combustion only at injection close to the top dead center during the compression stroke. The post injection has no influence on the compression work, only on the emissions and the indicated work. An optimal injection strategy was found to be: pilot SOI 19.2 CAD BTDC, pilot injection fuel mass 25.4%; main SOI 3.7 CAD BTDC, main injection fuel mass 67.3% mg; post SOI 2 CAD ATDC, post injection fuel mass 7.3% (the injection fuel mass is given as a percentage of the total fuel mass injected). This allows the indicated work near the base case level to be maintained, the pressure rise rate to decrease by 20% and NOx emissions to decrease by 10%, but leads to a 5% increase in PM emissions.

Effect of H2 and CO Content in Syngas on the Performance and Emission of Syngas-Diesel Dual Fuel Engine - A Review

2014 ◽  
Vol 699 ◽  
pp. 648-653 ◽  
Author(s):  
Bahaaddein K.M. Mahgoub ◽  
Suhaimi Hassan ◽  
Shaharin Anwar Sulaiman
Keyword(s):  
Carbon Monoxide ◽  
Diesel Engines ◽  
Combustion Process ◽  
Exhaust Emission ◽  
Dual Fuel ◽  
Pure Liquid ◽  
Compression Ignition ◽  
Performance And Emission ◽  
Combustion Duration ◽  
Combustible Gases

In this review, a series of research papers on the effects of hydrogen and carbon monoxide content in syngas composition on the performance and exhaust emission of compression ignition diesel engines, were compiled. Generally, the use of syngas in compression ignition (CI) diesel engine leads to reduce power output due to lower heating value when compared to pure liquid diesel mode. Therefore, variation in syngas composition, especially hydrogen and carbon monoxide (Combustible gases), is suggested to know the appropriate syngas composition. Furthermore, the simulated model of syngas will help to further explore the detailed effects of engine parameters on the combustion process including the ignition delay, combustion duration, heat release rate and combustion phasing. This will also contribute towards the efforts of improvement in performance and reduction in pollutants’ emissions from CI diesel engines running on syngas at dual fuel mode. Generally, the database of syngas composition is not fully developed and there is still room to find the optimum H2 and CO ratio for performance, emission and diesel displacement of CI diesel engines.

Post Fuel Injection Fuel Vaporization Characteristics in the Intake Port of a Port-Fuel-Injected Gasoline CFR Engine

2006 ◽  
Author(s):  
Jim S. Cowart ◽  
Leonard J. Hamilton
Keyword(s):  
Gasoline Engine ◽  
Fuel Injection ◽  
Fuel Vapor ◽  
Intake Port ◽  
Fuel Injector ◽  
Intake Valve ◽  
Inlet Port ◽  
Fuel Vaporization ◽  
Control Computer ◽  
Vapor Sampling

A Cooperative Fuels Research (CFR) gasoline engine has been modified to run on computer controlled Port Fuel Injection (PFI) and electronic ignition. Additionally a fast acting sampling valve (controlled by the engine control computer) has been placed in the engine’s intake system between the fuel injector and cylinder head in order to measure the fuel components that are vaporizing in the intake port immediately after the fuel injection event, and separately during the intake valve open period. This is accomplished by fast sampling a small portion of the intake port gases during a specified portion of the engine cycle which are then analyzed with a gas chromatograph. Experimental mixture preparation results as a function of inlet port temperature and pressure are presented. As the inlet port operates at higher temperatures and lower manifold pressures more of the injected fuels’ heavier components evolve into the vapor form immediately after fuel injection. The post-fuel injection fuel-air equivalence ratio in the intake port is characterized. The role of the fuel injection event is to produce from 1/4 to slightly over 1/2 of the combustible fuel-air mixture needed by the engine, as a function of port temperature. Fuel vapor sampling during the intake valve open period suggests that very little fuel is vaporizing from the intake port puddle below the fuel injector. In-cylinder fuel vapor sampling shows that significant fuel vapor generation must occur in the lower intake port and intake valve region.

Effect of Injection Timing on Combustion Characteristics of a DI Diesel Engine Fuelled with Pistacia chinensis Bunge Seed Biodiesel

2012 ◽  
Vol 614-615 ◽  
pp. 337-342
Author(s):  
Li Luo ◽  
Bin Xu ◽  
Zhi Hao Ma ◽  
Jian Wu ◽  
Ming Li
Keyword(s):  
Combustion Temperature ◽  
Fuel Injection ◽  
Direct Injection ◽  
Combustion Characteristics ◽  
Injection Timing ◽  
Brake Specific Fuel Consumption ◽  
Cylinder Pressure ◽  
Combustion Duration ◽  
Di Diesel Engine ◽  
Maximum Combustion Temperature

In this study, the effect of injection timing on combustion characteristics of a direct injection, electronically controlled, high pressure, common rail, turbocharged and intercooled engine fuelled with different pistacia chinensis bunge seed biodiesel/diesel blends has been experimentally investigated. The results indicated that brake specific fuel consumption reduces with the increasing of fuel injection advance angle and enhances with the increasing of biodiesel content in the blends. The peak of cylinder pressure and maximum combustion temperature increase evidently with the increment of fuel injection advance angle. However, the combustion of biodiesel blends starts earlier than diesel at the same fuel injection advance angle. At both conditions, the combustion duration and the peak of heat release rate are insensitive to the changing of injection timing.

scholarly journals Effects of Catalysts on Emissions of Pollutants from Combustion Processes of Liquid Fuels

2014 ◽  
Vol 13 (2) ◽  
pp. 5-17
Author(s):  
Agnieszka Bok ◽  
Joanna Guziałowska-Tic ◽  
Wilhelm Jan Tic
Keyword(s):  
Combustion Process ◽  
Combustion Products ◽  
Organometallic Complexes ◽  
Liquid Fuels ◽  
Motor Fuels ◽  
Harmful Emissions ◽  
Fuel Oils ◽  
Sulphur Oxides ◽  
Dynamic Growth ◽  
Combustion Processes

Abstract The dynamic growth of the use of non-renewable fuels for energy purposes results in demand for catalysts to improve their combustion process. The paper describes catalysts used mainly in the processes of combustion of motor fuels and fuel oils. These catalysts make it possible to raise the efficiency of oxidation processes simultanously reducing the emission of pollutants. The key to success is the selection of catalyst compounds that will reduce harmful emissions of combustion products into the atmosphere. Catalysts are introduced into the combustion zone in form of solutions miscible with fuel or with air supplied to the combustion process. The following compounds soluble in fuel are inclused in the composition of the described catalysts: organometallic complexes, manganese compounds, salts originated from organic acids, ferrocen and its derivatives and sodium chloride and magnesium chloride responsible for burning the soot (chlorides). The priority is to minimize emissions of volatile organic compounds, nitrogen oxides, sulphur oxides, and carbon monoxide, as well as particulate matter.

Sign in / Sign up

Export Citation Format

Share Document