COMPARISON OF FILM COOLING PERFORMANCE FOR DIFFERENT PURGE SLOT CONFIGURATIONS IN A CYLINDRICAL AND STATE-OF-THE-ART NOZZLE GUIDE VANE

2021 ◽  
pp. 1-13
Author(s):  
Christian Landfester ◽  
Gunther Mueller ◽  
Robert Krewinkel ◽  
Clemens Domnick ◽  
Martin Böhle
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
State Of The Art ◽  
Guide Vane ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract This comparative study is concerned with the advances in nozzle guide vane (NGV) design developments and their influence on endwall film cooling performance by injecting coolant through the purge slot. This experimental study compares the film cooling effectiveness and the aerodynamic effects for different purge slot configurations on both a flat and an axisymmetrically contoured endwall of a NGV. While the flat endwall cascade was equipped with cylindrical vanes, the contoured endwall cascade consisted of modern NGVs which represent state-of-the-art high-pressure turbine design standards. Geometric variations, e.g. the slot width and injection angle, as well as different blowing ratios were realized. The mainstream flow parameters were set to meet real engine conditions with regard to Reynolds and Mach numbers. Pressure Sensitive Paint was used to determine the adiabatic film cooling effectiveness. Five-hole probe measurements were performed to measure the flow field in the vane wake region. For a more profound insight into the origin of the secondary flows, oil dye visualizations were carried out. The results show that the advances in NGV design have a significantly positive influence on the distribution of the coolant. This has to be attributed to lesser disturbance of the coolant propagation by secondary flow for the optimized NGV design, since the design features are intended to suppress the formation of secondary flow. It is therefore advisable to take these effects into account when designing the film cooling system of a modern high-pressure turbine.

Comparison of Film Cooling Performance for Different Purge Slot Configurations in a Cylindrical and State-of-the-Art Nozzle Guide Vane

2021 ◽  
Author(s):  
Christian Landfester ◽  
Gunther Müller ◽  
Robert Krewinkel ◽  
Clemens Domnick ◽  
Martin Böhle
Keyword(s):  
Secondary Flow ◽  
Film Cooling ◽  
State Of The Art ◽  
Guide Vane ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract This comparative study is concerned with the advances in nozzle guide vane (NGV) design developments and their influence on the film cooling performance by injecting coolant through the purge slot. An experimental study compares the film cooling effectiveness as well as the aerodynamic effects for different purge slot configurations on both a flat and an axisymmetrically contoured endwall of a NGV. While the flat endwall cascade was equipped with four cylindrical vanes, the contoured endwall cascade consisted of four modern NGVs which represent state-of-the-art high-pressure turbine design standards. Geometric variations, e.g. the purge slot width and injection angle, as well as different blowing ratios (BR) at an engine-like density ratio (DR = 1.6) were realized to investigate the real-life effect of thermal expansion, design modifications and the interaction between secondary flow and coolant. The mainstream flow parameters were set to meet real engine conditions with regard to Reynolds and Mach numbers. The Pressure Sensitive Paint (PSP) technique was used to determine the adiabatic film cooling effectiveness. Five-hole probe measurements (DR = 1.0) were performed to measure the flow field with its characteristic vortex structures as well as the loss distribution in the vane wake region. For a more profound insight into the origin and development of the secondary flows, oil dye visualizations were carried out on both endwalls. The measurement results will be discussed based on a side-by-side comparison of the distribution of film cooling effectiveness on the endwall, its area-averaged values as well as the two-dimensional distribution of total pressure losses and the secondary flow field. The results of this study show that the advances in NGV design development have had a significantly positive influence on the distribution of the coolant. This has to be attributed to lesser disturbance of the coolant propagation by secondary flow for the optimized NGV design, since the design features are intended to suppress the formation of secondary flow. In contrast to the results of the cylindrical profile, sufficient cooling can be already provided with a perpendicular injection in the case of the modern NGV. It is therefore advisable to take these effects into account when designing the film cooling system of a modern high-pressure turbine.

Multi-Fidelity Modelling of a Fully-Featured HP Turbine Stage

2017 ◽  
Author(s):  
Giorgio Occhioni ◽  
Shahrokh Shahpar ◽  
Haidong Li
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
State Of The Art ◽  
Guide Vane ◽  
Phase Lag ◽  
Turbine Stage ◽  
High Pressure Turbine ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Film Cooling Holes

An improvement in overall efficiency and power output for gas turbine engines can be obtained by increasing the combustor exit temperature, but the thermal management of metal parts exposed to hot gases is challenging. Discrete film cooling, combined with internal convective cooling is the current state-of-the-art available to aerothermal designers of these components. To simplify the simulation problem in the aerodynamic design phase, it is common practice to replace the cooling holes with source strips applied to the blade. This could lead to inaccuracies in high pressure turbine performance prediction. This study has been carried out on a fully-featured high pressure turbine stage using high-fidelity simulations. The film cooling holes on the nozzle guide vane and on the rotor are initially modelled using a strip model approach. Then, to increase the model fidelity, the strips on the suction side of the rotor are replaced with discrete fan shaped film cooling holes. A rigid body rotation is also applied to the nozzle guide vane to vary the stage capacity and reaction. The effects of the mesh topology & resolution are also taken into account. The results obtained with these two approaches are then compared, giving the designers a better understanding on film cooling modelling and relationship between capacity, reaction and performance. The accurate prediction of the complex interaction between cavity inflows and the main-flow, still represent a challenge for the state of the art RANS solvers. Hence, an unsteady phase-lag approach has been used to overcome the RANS limitations. A validation of the unsteady solutions has been carried out with respect to experimental data.

Numerical Prediction of Cooling Performance Sensitivity of 1st Stage Nozzle Guide Vane Under Aerothermal Conditions

2019 ◽  
Author(s):  
Prasert Prapamonthon ◽  
Bo Yin ◽  
Guowei Yang ◽  
Mohan Zhang
Keyword(s):  
Heat Transfer ◽  
Surface Roughness ◽  
High Pressure ◽  
Guide Vane ◽  
Pressure Ratio ◽  
Inlet Temperature ◽  
High Pressure Turbine ◽  
Cooling Performance ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

Abstract To obtain high power and thermal efficiency, the 1st stage nozzle guide vanes of a high-pressure turbine need to operate under serious circumstances from burned gas coming out of combustors. This leads to vane suffering from effects of high thermal load, high pressure and turbulence, including flow-separated transition. Therefore, it is necessary to improve vane cooling performance under complex flow and heat transfer phenomena caused by the integration of these effects. In fact, these effects on a high-pressure turbine vane are controlled by several factors such as turbine inlet temperature, pressure ratio, turbulence intensity and length scale, vane curvature and surface roughness. Furthermore, if the vane is cooled by film cooling, hole configuration and blowing ratio are important factors too. These factors can change the aerothermal conditions of the vane operation. The present work aims to numerically predict sensitivity of cooling performances of the 1st stage nozzle guide vane under aerodynamic and thermal variations caused by three parameters i.e. pressure ratio, coolant inlet temperature and height of vane surface roughness using Computational Fluid Dynamics (CFD) with Conjugate Heat Transfer (CHT) approach. Numerical results show that the coolant inlet temperature and the vane surface roughness parameters have significant effects on the vane temperature, thereby affecting the vane cooling performances significantly and sensitively.

Application of Unsteady CFD Methods to Trailing Edge Cutback Film Cooling

2014 ◽  
Author(s):  
S. Ravelli ◽  
G. Barigozzi
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Navier Stokes ◽  
Trailing Edge ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Unsteady Rans ◽  
Exit Mach Number ◽  
Nozzle Guide

The main purpose of this numerical investigation is to overcome the limitations of the steady modeling in predicting the cooling efficiency over the cutback surface in a high pressure turbine nozzle guide vane. Since discrepancy between Reynolds-averaged Navier–Stokes (RANS) predictions and measured thermal coverage at the trailing edge was attributable to unsteadiness, Unsteady RANS (URANS) modeling was implemented to evaluate improvements in simulating the mixing between the mainstream and the coolant exiting the cutback slot. With the aim of reducing the computation effort, only a portion of the airfoil along the span was simulated at an exit Mach number of Ma2is = 0.2. Three values of the coolant-to-mainstream mass flow ratio were considered: MFR = 0.66%, 1.05%, and 1.44%. Nevertheless the inherent vortex shedding from the cutback lip was somehow captured by the URANS method, the computed mixing was not enough to reproduce the measured drop in adiabatic effectiveness η along the streamwise direction, over the cutback surface. So modeling was taken a step further by using the Scale Adaptive Simulation (SAS) method at MFR = 1.05%. Results from the SAS approach were found to have potential to mimic the experimental measurements. Vortices shedding from the cutback lip were well predicted in shape and magnitude, but with a lower frequency, as compared to PIV data and flow visualizations. Moreover, the simulated reduction in film cooling effectiveness toward the trailing edge was similar to that observed experimentally.

Overall Cooling Effectiveness Measurements on Pressure Side Surface of the Nozzle Guide Vane With Optimized Film Cooling Hole Arrangements

2017 ◽  
Author(s):  
Dong-Ho Rhee ◽  
Young Seok Kang ◽  
Bong Jun Cha ◽  
Sanga Lee
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Side Surface ◽  
Internal Cooling ◽  
Pressure Side ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Rib Turbulators ◽  
Nozzle Guide

Most of the optimization researches on film cooling have dealt with adiabatic film cooling effectiveness on the surface. However, the information on the overall cooling effectiveness is required to estimate exact performance of the optimization configuration since hot components such as nozzle guide vane have not only film cooling but also internal cooling features such as rib turbulators, jet impingement and pin-fins on the inner surface. Our previous studies [1,2] conducted the hole arrangement optimization to improve adiabatic film cooling effectiveness values and uniformity on the pressure side surface of the nozzle guide vane. In this study, the overall cooling effectiveness values were obtained at various cooling mass flow rates experimentally for the baseline and the optimized hole arrangements proposed by the previous study [1] and compared with the adiabatic film cooling effectiveness results. The tests were conducted at mainstream exit Reynolds number based on the chord of 2.2 × 106 and the coolant mass flow rate from 5 to 10% of the mainstream. For the experimental measurements, a set of tests were conducted using an annular sector transonic turbine cascade test facility in Korea Aerospace Research Institute. To obtain the overall cooling effectiveness values on the pressure side surface, the additive manufactured nozzle guide vane made of polymer material and Inconel 718 were installed and the surface temperature was measured using a FLIR infrared camera system. Since the optimization was based on the adiabatic film cooling effectiveness, the regions with rib turbulators and film cooling holes show locally higher overall cooling effectiveness due to internal convection and conduction, which can cause non-uniform temperature distributions. Therefore, the optimization of film cooling configuration should consider the effect of the internal cooling to avoid undesirable non-uniform cooling.

Optimal Arrangement of the Film Cooling Holes Considering the Manufacturing Tolerance for High Pressure Turbine Nozzle

2016 ◽  
Author(s):  
Sanga Lee ◽  
Dong-Ho Rhee ◽  
Kwanjung Yee
Keyword(s):  
High Pressure ◽  
Film Cooling ◽  
Leading Edge ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Cooling Performance ◽  
Film Cooling Effectiveness ◽  
Manufacturing Tolerance ◽  
Cooling Hole ◽  
Film Cooling Holes

In spite of a myriad of researches on the optimal shape of film cooling holes, only a few attempts have been made to optimize the hole arrangement for film cooling so far. Moreover, although the general scale of film cooling hole is so small that manufacturing tolerance has substantial effects on the cooling performance of turbine, the researches on this issue are even scarcer. If it is possible to obtain optimal hole arrangement which not only improve the film cooling performance but also is robust to the manufacturing tolerance, then overall cooling performance of a turbine would become more reliable and useful from the practical point of view. To this end, the present study proposed a robust design optimization procedure which takes the manufacturing uncertainties into account. The procedure was subsequently applied to the film cooling holes on high pressure turbine nozzle pressure side to obtain the robust array shape under the uncertainty of the manufacturing tolerance. First, the array of the holes was parameterized by 5 design variables using the newly suggested shape functions, and 2 representative factors were considered for the manufacturing tolerance of the film cooling hole. Probabilistic process that consists of Kriging surrogate model and Monte Carlo Simulation with descriptive sampling method was coupled with the design optimization process using Genetic Algorithm. Through this, film cooling hole array which shows the high performance, yet robust to the manufacturing tolerance was obtained, and the effects of the manufacturing tolerance on the cooling performance was carefully investigated. As a result, the region where the film cooling effectiveness is noticeable, as well as the maximum width of the variation of the film cooling effectiveness were reduced through optimization, and it is also confirmed that the tolerance of the holes near the leading edge is more influential to the cooling performance because the film cooling effectiveness is more sensitive to the manufacturing tolerance of the leading edge than that of the trailing edge.

Nozzle Guide Vane Film Cooling Effectiveness for Radial Showerheads With Restricted Cooling Hole Surface Angles

2017 ◽  
Author(s):  
Nicholas E. Holgate ◽  
Peter T. Ireland ◽  
Kevin P. Self
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Stagnation Region ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Cooling Hole ◽  
Leading Edges ◽  
Nozzle Guide ◽  
Surface Angle

Adiabatic film cooling effectiveness measurements are made on nozzle guide vane leading edges in an engine-realistic flow environment. The tested leading edges feature radial showerheads with different spanwise distributions of hole surface angle. The showerheads blow towards the midspan, except for one model with showerhead holes orthogonal to the vane surface. The results show that low surface angle radial showerhead holes generate high effectiveness within their rows and further downstream, but neglect the stagnation region lying between the two most upstream cooling hole rows. This downstream effectiveness gain is due to both the continued surface attachment of this coolant as it progresses downstream, and its beneficial interactions with downstream cooling jets. Moderate radial showerhead surface angles cause moderate coolant jet penetration into the mainstream, which promotes near-surface mixing of the coolant with the mainstream, increasing stagnation region effectiveness. The mixing effect is enhanced by the intense turbulence generated by combustor dilution jets. High surface angles may cause the stagnation region coolant to penetrate too far for either of these gains to be realised. Considering also the presence of endwall film cooling, these effects, taken together, suggest the superiority of radial showerheads which blow towards the midspan, as against those which blow towards each endwall. Surface temperature data is acquired by a novel infrared thermography technique which permits measurement of both heat transfer coefficient and film effectiveness from a single heated test.

Experimental Evaluation of Cooling Effectiveness of High Pressure Turbine Nozzle Guide Vane

2012 ◽  
Author(s):  
S. Venkatasubramanya ◽  
S. A. Vasudev ◽  
Sunil Chandel
Keyword(s):  
High Pressure ◽  
Air Temperature ◽  
Guide Vane ◽  
Internal Cooling ◽  
Temperature Ratio ◽  
High Pressure Turbine ◽  
Cooling Effectiveness ◽  
Nozzle Guide Vane ◽  
Nozzle Guide ◽  
Cooling Air

High pressure turbine nozzle guide vane of a gas turbine engine, which operates at gas temperatures in excess of 1700 K, employs internal cooling, augmented convective cooling, impingement cooling and film cooling techniques to keep the vane in safe operating limits. Even though nozzle guide vanes are designed using heat transfer co-relations available in published papers and fundamental data, it is required to test the nozzle guide vane to ascertain the surface metal temperature and verify the adequacy of cooling. Adequacy of cooling is quantified by the term cooling effectiveness expressed and as percentage. The objective of the current work is to study the effect of gas to cooling air temperature ratio on cooling effectiveness. In the current study tests were first conducted to validate the test cascade in accordance with AGARD recommendations. Later tests were conducted to verify the constancy of cooling effectiveness across two gas temperatures and finally effect of gas to cooling air temperature ratio on cooling effectiveness was studied. The ratio was increased by a factor of 0.69 in leading edge and 0.72 in the trailing edge circuit and found that the cooling effectiveness remained constant.

Endwall Film Cooling Using the Staggered Combustor-Turbine Gap Leakage Flow

2014 ◽  
Author(s):  
Yang Zhang ◽  
Xin Yuan
Keyword(s):  
Film Cooling ◽  
Guide Vane ◽  
Inlet Temperature ◽  
Local Pressure ◽  
Cooling Effectiveness ◽  
Film Cooling Effectiveness ◽  
Blowing Ratio ◽  
Blind Area ◽  
Nozzle Guide Vane ◽  
Nozzle Guide

A key technology of gas turbine performance improvement was the increase in the turbine inlet temperature, which brought high thermal loads to the Nozzle Guide Vane (NGV) components. Strong pressure gradients in the NGVs and the complex secondary flow field had made thermal protection more challenging. As for the endwall surface near the pressure side gill region, the relatively higher local pressure and cross flow apparently decreased the film-cooling effectiveness. The aim of this investigation was to evaluate a new design, improving the film-cooling performance in a cooling blind area with upstream staggered slot, simulating the combustor-turbine leakage gap flow. The test cascades model was manufactured according to the GE-E3 nozzle guide vane scaled model, with a scale ratio of 2.2. The experiment was performed under the inlet Mach number 0.1 and the Reynolds number 3.5×105 based on an axial chord length of 78 mm. The staggered slots were positioned upstream of the cascades to simulate the combustor-turbine gap leakage. The Pressure Sensitive Painting (PSP) technique was used to detect the film cooling effectiveness distribution on the endwall surface. Through the investigation, the following results could be achieved: 1) the film-cooling effectiveness on the endwall surface downstream the slot and along the pitchwise direction increased, with the highest parameter at Z/Pitch = 0.6; 2) a larger cooled region developed towards the suction side as the blowing ratio increased; 3) the advantage of the staggered slot was apparent on the endwall surface near the inlet area, while the coolant film was obviously weakened along the axial chord at a low blowing ratio. The influence of the staggered slots could only be detected in the downstream area of the endwall surface at the higher blowing ratio.

Sign in / Sign up

Export Citation Format

Share Document