Effects of Particle Size and Mainstream Inlet Angle on Deposition in a Turbine Cascade

2021 ◽  
Vol 143 (12) ◽  
Author(s):  
Jin Wang ◽  
Zhanming Zhao ◽  
Gongnan Xie ◽  
Hrvoje Mikulčić ◽  
Milan Vujanović ◽  
...  
Keyword(s):  
Particle Size ◽  
Velocity Model ◽  
Cylindrical Hole ◽  
Capture Efficiency ◽  
Turbine Cascade ◽  
Blowing Ratio ◽  
Hole Configuration ◽  
Impact Area ◽  
Inlet Angle ◽  
The Impact

Abstract Based on the critical velocity model, impact and capture efficiencies in an AGTB turbine cascade are investigated numerically under various inlet angles of mainstream, blowing ratios, particle sizes, and particle densities. The effect of hole configuration on deposition is analyzed based on comparisons of results from combined hole and cylindrical hole. The impact efficiency increases with the increase of particle size. Impact area on pressure side of blade surface expands with increasing of the mainstream inlet angle from 123 deg to 143 deg. The capture efficiency decreases with the increase of blowing ratio for 10 µm particles. For particles with densities of 1485 kg/m3, 1980 kg/m3, and 2475 kg/m3, the maximum capture efficiency is reached when the particle size is 5 µm. The particle capture efficiency for the combined hole is up to 3.9% lower than that for cylindrical hole when the mainstream inlet angle is 123 deg.

scholarly journals Waterfall Algorithm as a tool of investigation the geometrical features of granular porous media

2021 ◽  
Author(s):  
Wojciech Sobieski
Keyword(s):  
Particle Size ◽  
Porous Media ◽  
Lattice Boltzmann ◽  
Granular Media ◽  
Density Ratio ◽  
Geometrical Features ◽  
Granular Porous Media ◽  
Collision Density ◽  
Boltzmann Method ◽  
The Impact

AbstractThe paper describes the so-called Waterfall Algorithm, which may be used to calculate a set of parameters characterising the spatial structure of granular porous media, such as shift ratio, collision density ratio, consolidation ratio, path length and minimum tortuosity. The study is performed for 1800 different two-dimensional random pore structures. In each geometry, 100 individual paths are calculated. The impact of porosity and the particle size on the above-mentioned parameters is investigated. It was stated in the paper, that the minimum tortuosity calculated by the Waterfall Algorithm cannot be used directly as a representative tortuosity of pore channels in the Kozeny or the Carman meaning. However, it may be used indirect by making the assumption that a unambiguous relationship between the representative tortuosity and the minimum tortuosity exists. It was also stated, that the new parameters defined in the present study are sensitive on the porosity and the particle size and may be therefore applied as indicators of the geometry structure of granular media. The Waterfall Algorithm is compared with other methods of determining the tortuosity: A-Star Algorithm, Path Searching Algorithm, Random Walk technique, Path Tracking Method and the methodology of calculating the hydraulic tortuosity based on the Lattice Boltzmann Method. A very short calculation time is the main advantage of the Waterfall Algorithm, what meant, that it may be applied in a very large granular porous media.

scholarly journals A Numerical Study of the Effect of Particle Size on Particle Deposition on Turbine Vanes and Blades

2021 ◽  
Vol 13 (5) ◽  
pp. 168781402110178
Author(s):  
Zhengang Liu ◽  
Weinan Diao ◽  
Zhenxia Liu ◽  
Fei Zhang
Keyword(s):  
Particle Size ◽  
Particle Deposition ◽  
Numerical Study ◽  
Stokes Number ◽  
Capture Efficiency ◽  
Particle Capture ◽  
Factors Affecting ◽  
Pressure Surface ◽  
Deposition Area ◽  
Turbine Vanes

Particle deposition could decrease the aerodynamic performance and cooling efficiency of turbine vanes and blades. The particle motion in the flow and its temperature are two important factors affecting its deposition. The size of the particle influences both its motion and temperature. In this study, the motion of particles with the sizes from 1 to 20 μm in the first stage of a turbine are firstly numerically simulated with the steady method, then the particle deposition on the vanes and blades are numerically simulated with the unsteady method based on the critical viscosity model. It is discovered that the particle deposition on vanes mainly formed near the leading and trailing edge on the pressure surface, and the deposition area expands slowly to the whole pressure surface with the particle size increasing. For the particle deposition on blades, the deposition area moves from the entire pressure surface toward the tip with the particle size increasing due to the effect of rotation. For vanes, the particle capture efficiency increases with the particle size increasing since Stokes number and temperature of the particle both increase with its size. For blades, the particle capture efficiency increases firstly and then decreases with the particle size increasing.

scholarly journals Evaluation of Marblewood Dust’s (Marmaroxylon racemosum) Effect on Ignition Risk

2021 ◽  
Vol 11 (15) ◽  
pp. 6874
Author(s):  
Miroslava Vandličkova ◽  
Iveta Markova ◽  
Katarina Holla ◽  
Stanislava Gašpercová
Keyword(s):  
Particle Size ◽  
Dust Particles ◽  
Wood Dust ◽  
Sieve Analysis ◽  
Granulometric Analysis ◽  
Analysis Measurement ◽  
Risk Research ◽  
Minimum Ignition Temperature ◽  
The Impact

The paper deals with the selected characteristics, such as moisture, average bulk density, and fraction size, of tropical marblewood dust (Marmaroxylon racemosum) that influence its ignition risk. Research was focused on sieve analysis, granulometric analysis, measurement of moisture level in the dust, and determination of the minimum ignition temperatures of airborne tropical dust and dust layers. Samples were prepared using a Makita 9556CR 1400W grinder and K36 sandpaper for the purpose of selecting the percentages of the various fractions (<63, 63, 71, 100, 200, 315, 500 μm). The samples were sized on an automatic vibratory sieve machine Retsch AS 200. More than 65% of the particles were determined to be under 100 μm. The focus was on microfractions of tropical wood dust (particles with a diameter of ≤100 µm) and on the impact assessment of particle size (particle size <100 µm) on the minimum ignition temperatures of airborne tropical dust and dust layers. The minimum ignition temperature of airborne marblewood dust decreased with the particle size to the level of 400 °C (particle size 63 μm).

scholarly journals Aircraft Impact Effects on an Aged NPP

Materials ◽  
2021 ◽  
Vol 14 (4) ◽  
pp. 816
Author(s):  
Rosa Lo Frano
Keyword(s):  
Nuclear Power ◽  
Military Aircraft ◽  
Residual Resistance ◽  
Plant Safety ◽  
Need To Evaluate ◽  
Target Wall ◽  
Impact Area ◽  
Wall Perforation ◽  
The Impact ◽  
Loss Of Strength

The impact of an aircraft is widely known to be one of the worst events that can occur during the operation of a plant (classified for this reason as beyond design). This can become much more catastrophic and lead to the loss of strength of/collapse of the structures when it occurs in the presence of ageing (degradation and alteration) materials. Therefore, since the performance of all plant components may be affected by ageing, there is a need to evaluate the effect that aged components have on system performance and plant safety. This study addresses the numerical simulation of an aged Nuclear Power Plant (NPP) subjected to a military aircraft impact. The effects of impact velocity, direction, and location were investigated together with the more unfavorable conditions to be expected for the plant. The modelling method was also validated based on the results obtained from the experiments of Sugano et al., 1993. Non-linear analyses by means of finite element (FE) MARC code allowed us to simulate the performance of the reinforced concrete containment building and its impact on plant availability and reliability. The results showed that ageing increases a plant’s propensity to suffer damage. The damage at the impact area was confirmed to be dependent on the type of aircraft involved and the target wall thickness. The greater the degradation of the materials, the lower the residual resistance capacity, and the greater the risk of wall perforation.

scholarly journals Influence of the Spatial Pressure Distribution of Breaking Wave Loading on the Dynamic Response of Wolf Rock Lighthouse

2021 ◽  
Vol 9 (1) ◽  
pp. 55
Author(s):  
Darshana T. Dassanayake ◽  
Alessandro Antonini ◽  
Athanasios Pappas ◽  
Alison Raby ◽  
James Mark William Brownjohn ◽  
...  
Keyword(s):  
Dynamic Response ◽  
Pressure Distribution ◽  
Distinct Element ◽  
Breaking Waves ◽  
Breaking Wave ◽  
Wave Loading ◽  
Wave Impact ◽  
Pressure Distributions ◽  
Impact Area ◽  
The Impact

The survivability analysis of offshore rock lighthouses requires several assumptions of the pressure distribution due to the breaking wave loading (Raby et al. (2019), Antonini et al. (2019). Due to the peculiar bathymetries and topographies of rock pinnacles, there is no dedicated formula to properly quantify the loads induced by the breaking waves on offshore rock lighthouses. Wienke’s formula (Wienke and Oumeraci (2005) was used in this study to estimate the loads, even though it was not derived for breaking waves on offshore rock lighthouses, but rather for the breaking wave loading on offshore monopiles. However, a thorough sensitivity analysis of the effects of the assumed pressure distribution has never been performed. In this paper, by means of the Wolf Rock lighthouse distinct element model, we quantified the influence of the pressure distributions on the dynamic response of the lighthouse structure. Different pressure distributions were tested, while keeping the initial wave impact area and pressure integrated force unchanged, in order to quantify the effect of different pressure distribution patterns. The pressure distributions considered in this paper showed subtle differences in the overall dynamic structure responses; however, pressure distribution #3, based on published experimental data such as Tanimoto et al. (1986) and Zhou et al. (1991) gave the largest displacements. This scenario has a triangular pressure distribution with a peak at the centroid of the impact area, which then linearly decreases to zero at the top and bottom boundaries of the impact area. The azimuthal horizontal distribution was adopted from Wienke and Oumeraci’s work (2005). The main findings of this study will be of interest not only for the assessment of rock lighthouses but also for all the cylindrical structures built on rock pinnacles or rocky coastlines (with steep foreshore slopes) and exposed to harsh breaking wave loading.

Impact of Different Film-Cooling Modes at Trailing Edge on the Aerodynamic Performance of Heavy Duty Gas Turbine Cascade

2011 ◽  
Vol 84-85 ◽  
pp. 259-263
Author(s):  
Xun Liu ◽  
Song Tao Wang ◽  
Xun Zhou ◽  
Guo Tai Feng
Keyword(s):  
Gas Turbine ◽  
Film Cooling ◽  
Large Mass ◽  
Turbine Cascade ◽  
Heavy Duty ◽  
Trailing Edge ◽  
Central Difference ◽  
Adiabatic Effectiveness ◽  
Heavy Duty Gas Turbine ◽  
The Impact

In this paper, the trailing edge film cooling flow field of a heavy duty gas turbine cascade has been studied by central difference scheme and multi-block grid technique. The research is based on the three-dimensional N-S equation solver. By way of analysis of the temperature field, the distribution of profile pressure, and the distribution of film-cooling adiabatic effectiveness in the region of trailing edge with different cool air injection mass and different angles, it is found that the impact on the film-cooling adiabatic effectiveness is slightly by changing the injection mass. The distribution of profile pressure dropped intensely at the pressure side near the injection holes line with the large mass cooling air. The cooling effect is good in the region of trailing edge while the injection air is along the direction of stream.

Mechanical Response of Porous Copper Manufactured by Lost Carbonate Sintering Process

2007 ◽  
Vol 539-543 ◽  
pp. 1863-1867 ◽  
Author(s):  
X.F. Tao ◽  
Li Ping Zhang ◽  
Y.Y. Zhao
Keyword(s):  
Particle Size ◽  
Flexural Strength ◽  
Relative Density ◽  
Mechanical Response ◽  
Compaction Pressure ◽  
Absorption Capacity ◽  
Energy Absorption Capacity ◽  
Three Point Bending ◽  
Porous Copper ◽  
The Impact

This paper investigated the mechanical response of porous copper manufactured by LCS under three-point bending and Charpy impact conditions. The effects of the compaction pressure and K2CO3 particle size used in producing the porous copper samples and the relative density of the samples were studied. The apparent modulus, flexural strength and energy absorption capacity in three-point bending tests increased exponentially with increasing relative density. The impact strength was not markedly sensitive to relative density and had values within 7 – 9 kJ/m2 for the relative densities in the range 0.17 – 0.31. The amount of energy absorbed by a porous copper sample in the impact test was much higher than that absorbed in the three-point bending test, impling that loading strain rate had a significant effect on the deformation mechanisms. Increasing compaction pressure and increasing K2CO3 particle size resulted in significant increases in the flexural strength and the bending energy absorption capacity, both owing to the reduced sintering defects.

Grinding Force Model for Low-Speed Grinding Based on Impact Principle

2013 ◽  
Vol 797 ◽  
pp. 123-128
Author(s):  
Ming He Liu ◽  
Xiu Ming Zhang ◽  
Shi Chao Xiu
Keyword(s):  
Sliding Friction ◽  
Impact Load ◽  
Grinding Force ◽  
Calculation Model ◽  
Force Model ◽  
Grinding Process ◽  
Low Speed ◽  
Impact Area ◽  
Force Mechanism ◽  
The Impact

In the low-speed grinding process, the force generated when the wheel grinding the workpiece is the result of sliding friction, plough and cutting. While in the actual study, the cutting process has attracted extensive attention. Impact effect to the entire grinding process on the contact is ignored so that the error exists between the calculation grinding force and the measured grinding force. Basing on the shock effect to the grinding process, the paper divides the contact area into impact area and cutting area. And the model of impact load generated from single grit is built. Moreover, the grinding force theoretical calculation model and total grinding force mathematical model is also constructed by analyzing the impact load affecting on the grinding force mechanism. Finally experimental study verifies the correctness of theoretical analysis.

scholarly journals Effect of Particle Size Distribution on Powder Packing and Sintering in Binder Jetting Additive Manufacturing of Metals

2017 ◽  
Vol 139 (8) ◽  
Author(s):  
Yun Bai ◽  
Grady Wagner ◽  
Christopher B. Williams
Keyword(s):  
Particle Size ◽  
Additive Manufacturing ◽  
Large Degree ◽  
Full Density ◽  
Powder Particle Size ◽  
Powder Mixtures ◽  
Fine Powders ◽  
Sintering Shrinkage ◽  
The Impact ◽  
Binder Jetting

The binder jetting additive manufacturing (AM) process provides an economical and scalable means of fabricating complex parts from a wide variety of materials. While it is often used to fabricate metal parts, it is typically challenging to fabricate full density parts without large degree of sintering shrinkage. This can be attributed to the inherently low green density and the constraint on powder particle size imposed by challenges in recoating fine powders. To address this issue, the authors explored the use of bimodal powder mixtures in the context of binder jetting of copper. A variety of bimodal powder mixtures of various particle diameters and mixing ratios were printed and sintered to study the impact of bimodal mixtures on the parts' density and shrinkage. It was discovered that, compared to parts printed with monosized fine powders, the use of bimodal powder mixtures improves the powder's packing density (8.2%) and flowability (10.5%), and increases the sintered density (4.0%) while also reducing the sintering shrinkage (6.4%).

Sign in / Sign up

Export Citation Format

Share Document