Investigation of Unsteady Pressure Fluctuations in a Simplified Steam Turbine Control Valve

2021 ◽  
Author(s):  
Christian Windemuth ◽  
Martin Lange ◽  
Ronald Mailach
Keyword(s):  
Steam Turbine ◽  
Power Plants ◽  
Electrical Power ◽  
Pressure Fluctuations ◽  
Control Valve ◽  
Steam Turbines ◽  
Unsteady Forces ◽  
Part Load ◽  
Large Pressure ◽  
Wide Range

Abstract Steam turbines are among the most important systems in the conversion of thermal into electrical power. As the amount of renewable energies increases, existing power plants are experiencing increased times at part load conditions. To control the power output of a steam turbine, the use of control valves is a widely spread method, allowing fast load gradients and a quicker response on variable power requirements. At part load, a significant amount of energy is dissipated across the valve, as the total inlet pressure of the turbine is reduced. At these conditions, the flow across the valve becomes trans- and supersonic and large pressure fluctuations appear within the downstream part of the valve. As a result, unsteady forces can trigger strong vibrations, leading to mechanical stresses and possible valve failures. A spherical valve shape is still used in smaller industrial steam turbines, in which the flow is prone to show strong flow instabilities across a wide range of operating points. Because of these known instabilities, the spherical valve shape was chosen as the experimental test geometry and the evaluation of the unsteady flow and fluid-structure-interaction within the scaled steam turbine control valve. Using numerical methods, the test valve is investigated and the time dependent pressure distribution in the downstream diffuser is evaluated. The evolution of the flow stability will be discussed for different pressure ratios. Pressure signals retrieved from the control valve test rig will be used to compare the numerical results to experimental data.

Investigation of Unsteady Pressure Fluctuations in a Simplified Steam Turbine Control Valve

2020 ◽  
Author(s):  
Christian Windemuth ◽  
Martin Lange ◽  
Ronald Mailach
Keyword(s):  
Steam Turbine ◽  
Power Plants ◽  
Pressure Fluctuations ◽  
Control Valve ◽  
Steam Turbines ◽  
Unsteady Forces ◽  
Part Load ◽  
Large Pressure ◽  
Head Surface ◽  
Flow Through

Abstract Steam turbines are among the most important systems in commercial and industrial power conversion. As the amount of renewable energies increases, power plants formerly operated at steady state base load are now experiencing increased times at part load conditions. Besides other methods, the use of control valves is a widely spread method for controlling the power output of a steam turbine. In difference to other throttling approaches, the control valve enables fast load gradients as the boiler can be operated at constant conditions and allows a quicker response on variable power requirements. At part load, a significant amount of energy is dissipated across the valve, as the total inlet pressure of the turbine is decreased across the valve. At these conditions, the flow through the valve becomes trans- and supersonic and large pressure fluctuations appear within the downstream part of the valve. As a result, unsteady forces are acting on the valve structure and vibrations can be triggered, leading to mechanical stresses and possible failures of the valve. Besides more complex valve geometries, a spherical valve shape is still often used in smaller and industrial steam turbines. Because of the smooth head contour, the flow is prone to remain attached to the head surface and interact with the flow coming from the opposite side. This behaviour is accompanied by flow instabilities and large pressure fluctuations, leading to unsteady forces and possible couplings with mechanical frequencies. The spherical valve shape was therefore chosen as the experimental test geometry for the investigation of the unsteady flow field and fluid-structure-interactions within a scaled steam turbine control valve. Using numerical methods, the test valve is investigated and the time dependent pressure distribution in the downstream diffuser is evaluated. The evolution of the flow stability will be discussed for different pressure ratios. Pressure signals retrieved from the control valve test rig will be used to compare the numerical results to experimental data.

Effect of Inlet Steam Temperature on the HP Section Efficiency of a Steam Turbine

2015 ◽  
Author(s):  
Yiping Fu ◽  
Thomas Winterberger
Keyword(s):  
Steam Turbine ◽  
Power Plants ◽  
Pressure Ratio ◽  
Control Valve ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Steam Temperature ◽  
Load Range ◽  
Lp Turbine ◽  
The Relationship

Steam turbines for modern fossil and combined cycle power plants typically utilize a reheat cycle with High Pressure (HP), Intermediate Pressure (IP), and Low Pressure (LP) turbine sections. For an HP turbine section operating entirely in the superheat region, section efficiency can be calculated based on pressure and temperature measurements at the inlet and exhaust. For this case HP section efficiency is normally assumed to be a constant value over a load range if inlet control valve position and section pressure ratio remain constant. It has been observed that changes in inlet steam temperature impact HP section efficiency. K.C. Cotton stated that ‘the effect of throttle temperature on HP turbine efficiency is significant’ in his book ‘Evaluating and Improving Steam Turbine Performance’ (2nd Edition, 1998). The information and conclusions provided by K.C. Cotton are based on test results for large fossil units calculated with 1967 ASME steam tables. Since the time of Mr. Cotton’s observations, turbine configurations have evolved, more accurate 1997 ASME steam tables have been released, and our ability to quickly analyze large quantities of data has greatly increased. This paper studies the relationship between inlet steam temperature and HP section efficiency based on both 1967 and 1997 ASME steam tables and recent test data, which is analyzed computationally to reveal patterns and trends. With the efficiencies of various inlet pressure class HP section turbines being calculated with both 1967 and 1997 ASME steam tables, a comparison reveals different characteristics in the relationship between inlet steam temperature and HP section efficiency. Recommendations are made on how the results may be used to improve accuracy when testing and trending HP section performance.

Fault diagnosis method of peak-load-regulation steam turbine based on improved PCA-HKNN artificial neural network

2021 ◽  
pp. 1748006X2110105
Author(s):  
Yifan Wu ◽  
Wei Li ◽  
Deren Sheng ◽  
Jianhong Chen ◽  
Zitao Yu
Keyword(s):  
Neural Network ◽  
Fault Diagnosis ◽  
Steam Turbine ◽  
Power Plants ◽  
Peak Load ◽  
Clean Energy ◽  
Steam Turbines ◽  
Peak Shaving ◽  
Diagnosis Method ◽  
Load Regulation

Clean energy is now developing rapidly, especially in the United States, China, the Britain and the European Union. To ensure the stability of power production and consumption, and to give higher priority to clean energy, it is essential for large power plants to implement peak shaving operation, which means that even the 1000 MW steam turbines in large plants will undertake peak shaving tasks for a long period of time. However, with the peak load regulation, the steam turbines operating in low capacity may be much more likely to cause faults. In this paper, aiming at peak load shaving, a fault diagnosis method of steam turbine vibration has been presented. The major models, namely hierarchy-KNN model on the basis of improved principal component analysis (Improved PCA-HKNN) has been discussed in detail. Additionally, a new fault diagnosis method has been proposed. By applying the PCA improved by information entropy, the vibration and thermal original data are decomposed and classified into a finite number of characteristic parameters and factor matrices. For the peak shaving power plants, the peak load shaving state involving their methods of operation and results of vibration would be elaborated further. Combined with the data and the operation state, the HKNN model is established to carry out the fault diagnosis. Finally, the efficiency and reliability of the improved PCA-HKNN model is discussed. It’s indicated that compared with the traditional method, especially handling the large data, this model enhances the convergence speed and the anti-interference ability of the neural network, reduces the training time and diagnosis time by more than 50%, improving the reliability of the diagnosis from 76% to 97%.

Using CFD to Enhance the Preliminary Design of High-Pressure Steam Turbines

2013 ◽  
Author(s):  
Juri Bellucci ◽  
Federica Sazzini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Lorenzo Arcangeli ◽  
...  
Keyword(s):  
High Pressure ◽  
Steam Turbine ◽  
Design Tool ◽  
Tip Clearance ◽  
Large Set ◽  
Preliminary Design ◽  
Steam Turbines ◽  
High Pressure Steam ◽  
Wide Range ◽  
Pressure Steam

This paper focuses on the use of the CFD for improving a steam turbine preliminary design tool. Three-dimensional RANS analyses were carried out in order to independently investigate the effects of profile, secondary flow and tip clearance losses, on the efficiency of two high-pressure steam turbine stages. The parametric study included geometrical features such as stagger angle, aspect ratio and radius ratio, and was conducted for a wide range of flow coefficients to cover the whole operating envelope. The results are reported in terms of stage performance curves, enthalpy loss coefficients and span-wise distribution of the blade-to-blade exit angles. A detailed discussion of these results is provided in order to highlight the different aerodynamic behavior of the two geometries. Once the analysis was concluded, the tuning of a preliminary steam turbine design tool was carried out, based on a correlative approach. Due to the lack of a large set of experimental data, the information obtained from the post-processing of the CFD computations were applied to update the current correlations, in order to improve the accuracy of the efficiency evaluation for both stages. Finally, the predictions of the tuned preliminary design tool were compared with the results of the CFD computations, in terms of stage efficiency, in a broad range of flow coefficients and in different real machine layouts.

Repowering and Retrofitting

2002 ◽  
Author(s):  
Andreas Pickard
Keyword(s):  
Steam Turbine ◽  
Power Plants ◽  
Free Market ◽  
Leading Edge ◽  
Project Planning ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Planning Stage ◽  
Reheat Steam ◽  
Plant Optimization

At the start of this new century, environmental regulations and free-market economics are becoming the key drivers for the electricity generating industry. Advances in Gas Turbine (GT) technology, allied with integration and refinement of Heat Recovery Steam Generators (HRSG) and Steam Turbine (ST) plant, have made Combined Cycle installations the most efficient of the new power station types. This potential can also be realized, to equal effect, by adding GT’s and HRSG’s to existing conventional steam power plants in a so-called ‘repowering’ process. This paper presents the economical and environmental considerations of retrofitting the steam turbine within repowering schemes. Changing the thermal cycle parameters of the plant, for example by deletion of the feed heating steambleeds or by modified live and reheat steam conditions to suit the combined cycle process, can result in off-design operation of the existing steam turbine. Retrofitting the steam turbine to match the combined cycle unit can significantly increase the overall cycle efficiency compared to repowering without the ST upgrade. The paper illustrates that repowering, including ST retrofitting, when considered as a whole at the project planning stage, has the potential for greater gain by allowing proper plant optimization. Much of the repowering in the past has been carried out without due regard to the benefits of re-matching the steam turbine. Retrospective ST upgrade of such cases can still give benefit to the plant owner, especially when it is realized that most repowering to date has retained an unmodified steam turbine (that first went into operation some decades before). The old equipment will have suffered deterioration due to aging and the steam path will be to an archaic design of poor efficiency. Retrofitting older generation plant with modern leading-edge steam-path technology has the potential for realizing those substantial advances made over the last 20 to 30 years. Some examples, given in the paper, of successfully retrofitted steam turbines applied in repowered plants will show, by specific solution, the optimization of the economics and benefit to the environment of the converted plant as a whole.

Efficient Multi-Objective Optimization of Labyrinth Seal Leakage in Steam Turbines Based on Hybrid Surrogate Models

2016 ◽  
Author(s):  
Kevin Cremanns ◽  
Dirk Roos ◽  
Simon Hecker ◽  
Peter Dumstorff ◽  
Henning Almstedt ◽  
...  
Keyword(s):  
Steam Turbine ◽  
Surrogate Model ◽  
Power Plants ◽  
Polynomial Regression ◽  
Renewable Energy Sources ◽  
Surrogate Models ◽  
Future Market ◽  
Steam Turbines ◽  
Model Calculations ◽  
Highly Efficient

The demand for energy is increasingly covered through renewable energy sources. As a consequence, conventional power plants need to respond to power fluctuations in the grid much more frequently than in the past. Additionally, steam turbine components are expected to deal with high loads due to this new kind of energy management. Changes in steam temperature caused by rapid load changes or fast starts lead to high levels of thermal stress in the turbine components. Therefore, todays energy market requires highly efficient power plants which can be operated under flexible conditions. In order to meet the current and future market requirements, turbine components are optimized with respect to multi-dimensional target functions. The development of steam turbine components is a complex process involving different engineering disciplines and time-consuming calculations. Currently, optimization is used most frequently for subtasks within the individual discipline. For a holistic approach, highly efficient calculation methods, which are able to deal with high dimensional and multidisciplinary systems, are needed. One approach to solve this problem is the usage of surrogate models using mathematical methods e.g. polynomial regression or the more sophisticated Kriging. With proper training, these methods can deliver results which are nearly as accurate as the full model calculations themselves in a fraction of time. Surrogate models have to face different requirements: the underlying outputs can be, for example, highly non-linear, noisy or discontinuous. In addition, the surrogate models need to be constructed out of a large number of variables, where often only a few parameters are important. In order to achieve good prognosis quality only the most important parameters should be used to create the surrogate models. Unimportant parameters do not improve the prognosis quality but generate additional noise to the approximation result. Another challenge is to achieve good results with as little design information as possible. This is important because in practice the necessary information is usually only obtained by very time-consuming simulations. This paper presents an efficient optimization procedure using a self-developed hybrid surrogate model consisting of moving least squares and anisotropic Kriging. With its maximized prognosis quality, it is capable of handling the challenges mentioned above. This enables time-efficient optimization. Additionally, a preceding sensitivity analysis identifies the most important parameters regarding the objectives. This leads to a fast convergence of the optimization and a more accurate surrogate model. An example of this method is shown for the optimization of a labyrinth shaft seal used in steam turbines. Within the optimization the opposed objectives of minimizing leakage mass flow and decreasing total enthalpy increase due to friction are considered.

The Effect of Stage-Diffuser Interaction on the Aerodynamic Performance and Design of LP Steam Turbine Exhaust Systems

2018 ◽  
Author(s):  
Bowen Ding ◽  
Liping Xu ◽  
Jiandao Yang ◽  
Rui Yang ◽  
Yuejin Dai
Keyword(s):  
Steam Turbine ◽  
Renewable Energy Sources ◽  
Rotor Blades ◽  
Steam Turbines ◽  
Flow Conditions ◽  
Part Load ◽  
Last Stage ◽  
Load Conditions ◽  
Turbine Exhaust ◽  
Exhaust Systems

Modern large steam turbines for power generation are required to operate much more flexibly than ever before, due to the increasing use of intermittent renewable energy sources such as solar and wind. This has posed great challenges to the design of LP steam turbine exhaust systems, which are critical to recovering the leaving energy that is otherwise lost. In previous studies, the design had been focused on the exhaust diffuser with or without the collector. Although the interaction between the last stage and the exhaust hood has been identified for a long time, little attention has been paid to the last stage blading in the exhaust system’s design process, when the machine frequently operates at part-load conditions. This study focuses on the design of LP exhaust systems considering both the last stage and the exhaust diffuser, over a wide operating range. A 1/10th scale air test rig was built to validate the CFD tool for flow conditions representative of an actual machine at part-load conditions, characterised by highly swirling flows entering the diffuser. A numerical parametric study was performed to investigate the effect of both the diffuser geometry variation and restaggering the last stage rotor blades. Restaggering the rotor blades was found to be an effective way to control the level of leaving energy, as well as the flow conditions at the diffuser inlet, which influence the diffuser’s capability to recover the leaving energy. The benefits from diffuser resizing and rotor blade restaggering were shown to be relatively independent of each other, which suggests the two components can be designed separately. Last, the potentials of performance improvement by considering both the last stage rotor restaggering and the diffuser resizing were demonstrated by an exemplary design, which predicted an increase in the last stage power output of at least 1.5% for a typical 1000MW plant that mostly operates at part-load conditions.

Proper Orthogonal Decomposition and Extended- Proper Orthogonal Decomposition Analysis of Pressure Fluctuations and Vortex Structures Inside a Steam Turbine Control Valve

2018 ◽  
Vol 141 (4) ◽  
Author(s):  
Peng Wang ◽  
Hongyu Ma ◽  
Yingzheng Liu
Keyword(s):  
Proper Orthogonal Decomposition ◽  
Steam Turbine ◽  
Pressure Fluctuation ◽  
Pressure Field ◽  
Pressure Fluctuations ◽  
Control Valve ◽  
Vortex Structures ◽  
Orthogonal Decomposition ◽  
Pod Analysis ◽  
Proper Orthogonal

In steam turbine control valves, pressure fluctuations coupled with vortex structures in highly unsteady three-dimensional flows are essential contributors to the aerodynamic forces on the valve components, and are major sources of flow-induced vibrations and acoustic emissions. Advanced turbulence models can capture the detailed flow information of the control valve; however, it is challenging to identify the primary flow structures, due to the massive flow database. In this study, state-of-the-art data-driven analyses, namely, proper orthogonal decomposition (POD) and extended-POD, were used to extract the energetic pressure fluctuations and dominant vortex structures of the control valve. To this end, the typical annular attachment flow inside a steam turbine control valve was investigated by carrying out a detached eddy simulation (DES). Thereafter, the energetic pressure fluctuation modes were determined by conducting POD analysis on the pressure field of the valve. The vortex structures contributing to the energetic pressure fluctuation modes were determined by conducting extended-POD analysis on the pressure–velocity coupling field. Finally, the dominant vortex structures were revealed conducting a direct POD analysis of the velocity field. The results revealed that the flow instabilities inside the control valve were mainly induced by oscillations of the annular wall-attached jet and the derivative flow separations and reattachments. Moreover, the POD analysis of the pressure field revealed that most of the pressure fluctuation intensity comprised the axial, antisymmetric, and asymmetric pressure modes. By conducting extended-POD analysis, the incorporation of the vortex structures with the energetic pressure modes was observed to coincide with the synchronous, alternating, and single-sided oscillation behaviors of the annular attachment flow. However, based on the POD analysis of the unsteady velocity fields, the vortex structures, buried in the dominant modes at St = 0.017, were found to result from the alternating oscillation behaviors of the annular attachment flow.

Lifetime Assessments of an Old Westinghouse-Design Steam Chest

2012 ◽  
Author(s):  
Sazzadur Rahman ◽  
Waheed Abbasi ◽  
Thomas W. Joyce
Keyword(s):  
Steam Turbine ◽  
Material Properties ◽  
Power Plants ◽  
Real Life ◽  
Cyclic Stress ◽  
Steam Turbines ◽  
Reliable Operation ◽  
Steady State Operation ◽  
Different Temperatures ◽  
Transient Events

Fossil steam turbines were designed for approximately thirty years of reliable operation based on a normal duty cycle. During operation, highly stressed components of steam turbine power plants undergo a change in material properties due to cyclic stress and exposure to different temperatures. Among all the components of a steam turbine, the steam chest is affected the most as it experiences a wide variation of stresses and loads during transient events and steady-state operation. These factors can strongly influence the metallurgical condition and overall reliable life of steam chests. In this paper, Siemens’ overall approach for lifetime assessments will be discussed with a real life example on a 40 year old Westinghouse-design steam chest. The methodology and the findings from the assessment are also discussed.

Coordinated Control of Gas and Steam Turbines for Efficient Fast Start-Up of Combined Cycle Power Plants

2016 ◽  
Vol 139 (2) ◽  
Author(s):  
Yasuhiro Yoshida ◽  
Kazunori Yamanaka ◽  
Atsushi Yamashita ◽  
Norihiro Iyanaga ◽  
Takuya Yoshida
Keyword(s):  
Thermal Stress ◽  
Steam Turbine ◽  
Gas Turbines ◽  
Power Plants ◽  
Thermal Stresses ◽  
Control Method ◽  
Coordinated Control ◽  
Combined Cycle ◽  
Steam Turbines ◽  
Start Up

In the fast start-up for combined cycle power plants (CCPP), the thermal stresses of the steam turbine rotor are generally controlled by the steam temperatures or flow rates by using gas turbines (GTs), steam turbines, and desuperheaters to avoid exceeding the thermal stress limits. However, this thermal stress sensitivity to steam temperatures and flow rates depends on the start-up sequence due to the relatively large time constants of the heat transfer response in the plant components. In this paper, a coordinated control method of gas turbines and steam turbine is proposed for thermal stress control, which takes into account the large time constants of the heat transfer response. The start-up processes are simulated in order to assess the effect of the coordinated control method. The simulation results of the plant start-ups after several different cool-down times show that the thermal stresses are stably controlled without exceeding the limits. In addition, the steam turbine start-up times are reduced by 22–28% compared with those of the cases where only steam turbine control is applied.

Sign in / Sign up

Export Citation Format

Share Document