Study of a Gamma Radiation Impact on Concrete Properties Under Severe Accident Conditions

2020 ◽  
Vol 7 (2) ◽  
Author(s):  
Zbyněk Hlaváč ◽  
Jaroslava Zatloukalová ◽  
Michal Košťál ◽  
Evžen Losa
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Radiation Effects ◽  
Experimental Studies ◽  
Life Time ◽  
Severe Accident ◽  
Research Centre ◽  
Concrete Properties ◽  
60Co Source ◽  
Operational Life

Abstract Concrete is an important structural material used in nuclear power plant (NPP) design. Due to relatively high amount of hydrogen as well as the presence of heavier elements, it also acts as a biological shielding. One of the important tasks for prolongation of operational life time is the determination of concrete components' condition after long-term irradiation. The paper aims to present the current activities in the CV Řež institute (Research Centre Řež—CVR) regarding the investigation of ionizing radiation effects on concrete properties. In its first part, the paper deals with experimental identification of the character of mixed neutron and gamma spectra in the concrete part of the VVER-1000 Mock-Up. Using the knowledge, the radiation field character can be scaled up to the commercial power plants with VVER-1000 light water reactor. It also provides justification for usage of the 60Co source for performed irradiation experiments with concrete. The second part of the article describes the experimental studies of the properties of gamma-irradiated concrete samples by strong 60Co source. This irradiation experiment can be understood as the first step in characterizing concrete degradation as gamma flux in biological shielding is significantly higher than that of neutron flux. In order to better understand the concrete properties and the behavior under irradiation, nondestructive as well as destructive testing methods were applied. We found that after 48 days of irradiation by the 60Co source the sample obtained dose from gamma corresponding to approximately 1% of the total during the NPP lifetime operation. Concrete microstructure degraded and the modulus of elasticity slightly decreased within 5%. Conversely, destruction tests prove significant flexural strength decrease by 27% in case of normal test and by 63% at the loss of coolant accident (LOCA) test.

Hydrogen Deflagration Analysis in THAI Experiments Using MELCOR Code

2020 ◽  
Author(s):  
Alain Flores y Flores ◽  
Guido Mazzini
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Control Volume ◽  
Critical Issue ◽  
Severe Accident ◽  
Test Facility ◽  
Research Centre ◽  
Time Step ◽  
Volume Number ◽  
Fukushima Daiichi

Abstract In order to develop an appropriate knowledge to support the SUJB (State Office of Nuclear Safety), the CVR (Research Centre Rež), in collaboration with SURO (National Radiation Protection Institute) is developing a methodology to simulate nuclear power plants under accidental conditions. A particular effort is focused in the severe accident phenomenology where hydrogen deflagration carries a critical issue for the containment integrity, such as Fukushima Daiichi accident. For this purpose, THAI (Thermal-hydraulics, hydrogen, aerosol and iodine) experimental campaigns are chosen due to the several tests involved in different conditions. THAI containment test facility is used to open questions concerning the behaviour of hydrogen, iodine and aerosols in the containment of water-cooled reactors during severe accidents. The Fukushima Daiichi Accident demonstrates that the hydrogen deflagration could lead to a significant containment damage. For this reason, a particular attention is given to the hydrogen deflagration scenario. All simulations are prepared and modelled in MELCOR 2.1. The results obtained showed a strong influence related with some factors as: the nodalization pattern, control volume number (CV), flow paths number FP and time step. In order to assess the THAI model with the THAI final reports, a sensitivity analysis focused with those parameters was performed.

scholarly journals A decision-support approach to severe accident management in nuclear power plants

2020 ◽  
pp. 1-12
Author(s):  
Marko Bohanec ◽  
Ivan Vrbanić ◽  
Ivica Bašić ◽  
Klemen Debelak ◽  
Luka Štrubelj
Keyword(s):  
Decision Support ◽  
Nuclear Power ◽  
Power Plants ◽  
Nuclear Power Plants ◽  
Severe Accident ◽  
Accident Management

scholarly journals A Conceptual Approach to Eliminate Bypass Release of Fission Products by In-Containment Relief Valve under SGTR Accident

2018 ◽  
Vol 2018 ◽  
pp. 1-12
Author(s):  
Taeseok Kim ◽  
Wonjun Choi ◽  
Joongoo Jeon ◽  
Nam Kyung Kim ◽  
Hoichul Jung ◽  
...  
Keyword(s):  
Steam Generator ◽  
Nuclear Power ◽  
Power Plants ◽  
Fission Products ◽  
Mitigation Strategies ◽  
Severe Accident ◽  
Base Case ◽  
Conceptual Approach ◽  
Relief Valve ◽  
Radioactive Nuclides

During a hypothesized severe accident, a containment building is designed to act as a final barrier to prevent release of fission products to the environment in nuclear power plants. However, in a bypass scenario of steam generator tube rupture (SGTR), radioactive nuclides can be released to environment even if the containment is not ruptured. Thus, thorough mitigation strategies are needed to prevent such unfiltered release of the radioactive nuclides during SGTR accidents. To mitigate the consequence of the SGTR accident, this study was conducted to devise a conceptual approach of installing In-Containment Relief Valve (ICRV) from steam generator (SG) to the free space in the containment building and it was simulated by MELCOR code for numerical analysis. Simulation results show that the radioactive nuclides were not released to the environment in the ICRV case. However, the containment pressure increased more than the base case, which is a disadvantage of the ICRV. To minimize the negative effects of the ICRV, the ICRV linked to Reactor Drain Tank (RDT) and cavity flooding was performed. Because the overpressurization of containment is due to heat of ex-vessel corium, only cavity flooding was effective for depressurization. The conceptual design of the ICRV is effective in mitigating the SGTR accident.

Analyzing Droplet Size Distributions Inside a Self-Priming Venturi Scrubber for Filtered Containment Venting Systems

2018 ◽  
Author(s):  
P. Papadopoulos ◽  
T. Lind ◽  
H.-M. Prasser
Keyword(s):  
Droplet Size ◽  
High Speed ◽  
Nuclear Power ◽  
Power Plants ◽  
Gas Flow ◽  
Tube Bundle ◽  
Droplet Size Distribution ◽  
Severe Accident ◽  
Design Element ◽  
Venturi Scrubber

After the accident in the Fukushima Daiichi nuclear power plant, the interest of adding Filtered Containment Venting Systems (FCVS) on existing nuclear power plants to prevent radioactive releases to the environment during a severe accident has increased. Wet scrubbers are one possible design element which can be part of an FCVS system. The efficiency of this scrubber type is thereby depending, among others, on the thermal-hydraulic characteristics inside the scrubber. The flow structure is mainly established by the design of the gas inlet nozzle. The venturi geometry is one of the nozzle types that can be found in nowadays FCVS. It acts in two different steps on the removal process of the contaminants in the gas stream. Downstream the suction opening in the throat of the venturi, droplets are formed by atomization of the liquid film. The droplets are contributing to the capture of aerosols and volatile gases from the mixture coming from the containment. Studies state that the majority of the contaminants is scrubbed within this misty flow regime. At the top of the venturi, the gas stream is injected into the pool. The pressure drop at the nozzle exit leads to the formation of smaller bubbles, thus increasing the interfacial area concentration in the pool. In this work, the flow inside a full-scale venturi scrubber has been optically analyzed using shadowgraphy with a high-speed camera. The venturi nozzle was installed in the TRISTAN facility at PSI which was originally designed to investigate the flow dynamics of a tube rupture inside a full-length scale steam generator tube bundle. The data analysis was focused on evaluating the droplet size distribution and the Sauter mean diameter under different gas flow rates and operation modes. The scrubber was operated in two different ways, submerged and unsubmerged. The aim was to include the effect on the droplet sizes of using the nozzle in a submerged operation mode.

scholarly journals Spreading of Excellence in SARNET Network on Severe Accidents: The Education and Training Programme

2012 ◽  
Vol 2012 ◽  
pp. 1-9 ◽  
Author(s):  
Sandro Paci ◽  
Jean-Pierre Van Dorsselaere
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Training Programme ◽  
Education And Training ◽  
Severe Accident ◽  
Research Network ◽  
Safety Issues ◽  
Severe Accidents ◽  
Management Procedures ◽  
And Training

The SARNET2 (severe accidents Research NETwork of Excellence) project started in April 2009 for 4 years in the 7th Framework Programme (FP7) of the European Commission (EC), following a similar first project in FP6. Forty-seven organisations from 24 countries network their capacities of research in the severe accident (SA) field inside SARNET to resolve the most important remaining uncertainties and safety issues on SA in water-cooled nuclear power plants (NPPs). The network includes a large majority of the European actors involved in SA research plus a few non-European relevant ones. The “Education and Training” programme in SARNET is a series of actions foreseen in this network for the “spreading of excellence.” It is focused on raising the competence level of Master and Ph.D. students and young researchers engaged in SA research and on organizing information/training courses for NPP staff or regulatory authorities (but also for researchers) interested in SA management procedures.

Computational Study of Conjugate Heat Transfer in T-Junctions

2009 ◽  
Author(s):  
Simon Kuhn ◽  
Bojan Nicˇeno ◽  
Horst-Michael Prasser
Keyword(s):  
Thermal Fatigue ◽  
Nuclear Power ◽  
Power Plants ◽  
Cold Water ◽  
Computational Study ◽  
Solid Wall ◽  
Turbulent Viscosity ◽  
Life Time ◽  
Scale Model ◽  
Piping Systems

Thermal fatigue is a relevant problem in the context of life-time extension of nuclear power plants (NPP). In many piping systems in NPPs hot and cold water is mixed, which leads to high temperature fluctuations in the region close to the solid wall and resulting thermal loads on the pipe walls that can cause fatigue. One of the relevant geometric test cases for thermal fatigue is the mixing in T-junctions. In this study we apply large–eddy simulations (LES) to the mixing of hot and cold water in a T-junction. We perform a set of simulations by using different formulations of the LES subgrid scale model, i.e. standard Smagorinsky and dynamic procedure, to identify the influence of the modelled subgrid scales on the simulation results. The results exhibit a large difference between the models, which is caused by the use of turbulent viscosity wall–damping functions when applying the standard model.

Fracture Toughness Predictive Models Within the SOTERIA EU Project

2018 ◽  
Author(s):  
P. M. James ◽  
M. Berveiller
Keyword(s):  
Cleavage Fracture ◽  
Nuclear Power ◽  
Power Plants ◽  
Radiation Effects ◽  
Austenitic Stainless Steels ◽  
Irradiation Damage ◽  
Tensile Behaviour ◽  
Horizon 2020 ◽  
Term Operation

SOTERIA is focused on the ‘safe long term operation of light water reactors’. This will be achieved through an improved understanding of radiation effects in nuclear structural materials. This project has received funding from the European Union’s Horizon 2020 research and innovation programme under agreement No 661913. The overall aim of the SOTERIA project is to improve the understanding of the ageing phenomena occurring in ferritic reactor pressure vessel steels and in the austenitic internals in order to provide crucial information to regulators and operators to ensure safe long-term operation (LTO) of existing European nuclear power plants (NPPs). SOTERIA has set up a collaborative research consortium which gathers the main European research centers and industrial partners who will combine advanced modelling tools with the exploitation of experimental data to focus on two major objectives: i) to identify ageing mechanisms when materials face environmental degradation (such as e.g. irradiation and corrosion) and ii) to provide a single platform containing data and tools for reassessment of structural components during NPPs lifetime. This paper provides an overview of the ongoing activities within the SOTERIA Project that are contained within the analytical work-package (WP5.3). These fracture aspects are focused on the estimates of fracture in both ferritic steels and irradiation assisted stress corrosion cracking (IASCC) in austenitic stainless steels, under irradiated conditions. This analytical development is supported by analytical estimates of irradiation damage and the resulting changes in tensile behaviour of the steels elsewhere in SOTERIA, as well as a wider number of experimental programmes. Cleavage fracture estimates are being considered by a range of modelling estimates including the Beremin, Microstructurally Informed Brittle Fracture Model (MIBF), JFJ and Bordet Models with efforts being made to understand the influence of heterogeneity on the predicted toughness’s. Efforts are also being considered to better understand ductile void evolution and the effect of plasticity on the cleavage fracture predictions. IASCC is being modelled through the INITEAC code previously developed within the predecessor project Perform 60 which is being updated to incorporate recent developments from within SOTERIA and elsewhere.

Reliability Monitor for PWR Safety System Using FMEA and Go-Flow Methodology: Application of Risk Monitor for Nuclear Power Plants

2013 ◽  
Author(s):  
Muhammad Hashim ◽  
Hidekazu Yoshikawa ◽  
Takeshi Matsuoka ◽  
Ming Yang
Keyword(s):  
Nuclear Power ◽  
Power Plants ◽  
Fault Tree Analysis ◽  
Reliability Evaluation ◽  
Safety System ◽  
Severe Accident ◽  
Monitor System ◽  
Dynamic Reliability ◽  
Defense In Depth ◽  
Risk Monitor

Author’s proposed risk monitor system of Nuclear Power Plant (NPP) is based on the idea of Plant Defense-in-Depth (DiD) risk monitor and reliability monitor to monitor what degree of safety functions incorporated in the plant system is maintained by multiple barriers of Defense-in-Depth (DiD). In the risk monitor system, the range of risk state is not limited in core damage accident but includes all kinds of dangerous states brought by severe accident. In present study, method of the reliability monitor of a risk monitor system is applied to the PWR safety system in order to evaluate the risk state numerically by pursuing all conditions of reliability evaluation given by plant DiD risk monitor. Large break LOCA is taken as an initiating accident event and the implementation of method of the reliability monitor is discussed in detail for single loop PWR safety system by considering the Multilevel Flow Model (MFM), Failure Mode and Effect Analysis (FMEA), and the qualitative reliability evaluation by Fault Tree Analysis (FTA) and the dynamic reliability evaluation by GO-FLOW. The summary of reliability results of PWR safety subsystems are also presented.

Sign in / Sign up

Export Citation Format

Share Document