Streamwise Aspect Ratio Effects on Turbulent Flow Separations Induced by Forward–Backward-Facing Steps

2020 ◽  
Vol 143 (2) ◽  
Author(s):  
Heath Chalmers ◽  
Xingjun Fang ◽  
Mark F. Tachie
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Turbulent Boundary Layer ◽  
Step Height ◽  
Bluff Bodies ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Freestream Velocity ◽  
Aspect Ratios ◽  
The Mean

Abstract Separated and reattached turbulent flows induced by two-dimensional forward–backward-facing steps (FBFS) with different streamwise lengths submerged in a thick turbulent boundary layer (TBL) are investigated using time-resolved particle image velocimetry (TR-PIV). The aspect ratios (AR) of the step range from 1 to 8, and the Reynolds number based on the freestream velocity and step height is 13 200. The thickness of the incoming turbulent boundary layer is 6.5 times the step height. The effects of varying aspect ratio of the steps on the mean flow, principal stretching, Reynolds stresses, triple velocity correlation, two-point autocorrelation, and unsteadiness of turbulent separation bubbles are studied. The results indicate that the mean flow reattaches over the step for FBFS with aspect ratios of 2 and higher. Two local peaks of Reynolds stresses occur irrespective of AR, and for a sufficiently large AR, a third local peak of Reynolds stresses appear in the shear layer emanating from the trailing edge of the bluff bodies. The streamwise decay of Reynolds stresses is slower for smaller AR cases. Incoming coherent structure is strongly disturbed near an inclined edge where principal stretching switches orientation abruptly. The temporal variation of the first proper orthogonal decomposition (POD) mode and reverse flow area over the bluff bodies shows remarkable correlation, which signifies the flapping motion of separation bubble.

Effects of Streamwise Aspect Ratio on Turbulent Flows Over Forward-Backward Facing Steps

2020 ◽  
Author(s):  
Heath Chalmers ◽  
Xingjun Fang ◽  
Mark F. Tachie
Keyword(s):  
Boundary Layer ◽  
Aspect Ratio ◽  
Turbulent Boundary Layer ◽  
Turbulent Flows ◽  
Separation Bubble ◽  
Step Height ◽  
Stream Velocity ◽  
Mean Flow ◽  
Aspect Ratios ◽  
The Mean

Abstract Separated and reattached turbulent flows induced by two-dimensional forward-backward-facing steps with different streamwise lengths submerged in a thick turbulent boundary layer are investigated using a time-resolved particle image velocimetry. The examined aspect ratios of the step range from 1 to 8, and the Reynolds number based on the free-stream velocity and step height is 13 200. The thickness of the oncoming turbulent boundary layer is 6.5 times the step height. The effects of varying aspect ratio of the steps on the mean flow, Reynolds stresses, triple correlations and unsteadiness of turbulent separation bubbles are studied. It was found that the mean flow reattaches over the step for forward-backward facing steps with aspect ratios of 2 and higher. The temporal variation of the first proper orthogonal decomposition (POD) mode and reverse flow area, which is used to examine the flapping motion of separation bubble, shows remarkable synchronization.

An Experimental Study of Surface-Mounted Bluff Bodies Immersed in Deep Turbulent Boundary Layers

2018 ◽  
Author(s):  
Helen A. Amorin ◽  
Xingjun Fang ◽  
Mark F. Tachie
Keyword(s):  
Boundary Layer ◽  
Experimental Study ◽  
Aspect Ratio ◽  
Water Channel ◽  
Open Water ◽  
Step Height ◽  
Bluff Bodies ◽  
Reynolds Stresses ◽  
Reattachment Length ◽  
Aspect Ratios

This paper reports an experimental study conducted to investigate the effects of aspect ratio on the reattachment length and statistical properties in turbulent flow over three-dimensional surface-mounted bluff bodies. This study focuses on a surface-mounted body whose height is significantly smaller than the thickness of the approaching turbulent boundary layer. The studied aspect ratios of the step range from w/h = 0.5 to 20, where w and h denote the spanwise width and height of the step, respectively. All experiments were carried out in an open water channel, and the velocity measurements were performed using a time-resolved particle image velocimetry (TR-PIV) system. The Reynolds number, based on the freestream of the approach boundary layer and step height, is 12540, while the ratio of the boundary layer to step height is 4.83. Two distinct regions of separation are observed on top of the step and downstream of the step. In both separation regions, the reattachment length increases monotonically as aspect ratio increases from w/h = 0.5 to 8, and the reattachment length reaches an asymptotic value and does not vary significantly with aspect ratio larger than 8. The effects of aspect ratios on the mean velocities and Reynolds stresses were also examined.

On turbulent boundary layers in oscillatory flow

1977 ◽  
Vol 353 (1672) ◽  
pp. 121-144 ◽  
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Boundary Layers ◽  
Travelling Wave ◽  
Convection Velocity ◽  
Mean Flow ◽  
Mean Velocity ◽  
Flow Measurements ◽  
Freestream Velocity ◽  
The Mean

An experimental investigation has been made of turbulent boundary layer response to harmonic oscillations associated with a travelling wave imposed on an otherwise constant freestream velocity and convected in the freestream direction. The tests covered oscillation frequencies of 4-12 Hz for freestream amplitudes of up to 11% of the mean velocity. Additional steady flow measurements were used to infer the quasi-steady response to freestream oscillations. The results show a welcome insensitivity of the mean flow and turbulent intensity distributions to the freestream oscillations tested. An approximate analysis based on these results has been developed. It is probably of limited validity but it does provide a useful guide to the physical processes involved. The effects on boundary layer response of varying the travelling wave convection velocity and frequency of oscillation are illustrated by the analysis and show a behaviour broadly similar to that of laminar boundary layers. The travelling wave convection velocity exhibits a dominant influence on the turbulent boundary layer response to freestream oscillations.

Turbulent Flow Around Rectangular Cylinders with Different Streamwise Aspect Ratios

2021 ◽  
Author(s):  
Sedem Kumahor ◽  
Mark F. Tachie
Keyword(s):  
Aspect Ratio ◽  
High Speed ◽  
Second Harmonic ◽  
Cylinder Surface ◽  
Large Aspect Ratio ◽  
Reynolds Stresses ◽  
Square Cylinder ◽  
Mean Flow ◽  
Aspect Ratios ◽  
The Mean

Abstract Turbulent flows around a square cylinder and a rectangular cylinder with a streamwise aspect ratio of 5 in a uniform flow were investigated using time-resolved particle image velocimetry. The Reynolds number based on the cylinder height and oncoming flow velocity was 16200. Similarities and differences in the flow dynamics over the cylinders and in the near wake region were examined in terms of the mean flow, Reynolds stresses and triple velocity correlations. The budget of turbulent kinetic energy as well as temporal and spectral analyses were also performed. The results show that the primary, secondary and wake vortexes are smaller for the square cylinder compared to the large aspect ratio cylinder. There are regions of elevated Reynolds stresses and triple velocity correlations along the mean separating streamlines, and the magnitudes of these statistics are an order of magnitude higher over the square cylinder compared to the large aspect ratio cylinder. The topology of the triple velocity correlations shows low-speed ejection and high-speed sweep events, respectively, transporting instantaneous Reynolds normal stresses away from the mean separating streamline into the free-stream and toward the cylinder surface, regardless of aspect ratio. Near the leading and trailing edges of both cylinders, regions of negative turbulence production are observed and the dominant components contributing to this occurrence are discussed. Temporal autocorrelation coefficients of the streamwise and vertical velocity fluctuations show a periodic trend, with a periodicity that is directly linked to the Kármán shedding frequency and its second harmonic.

Reynolds-number scaling of the flat-plate turbulent boundary layer

2000 ◽  
Vol 422 ◽  
pp. 319-346 ◽  
Author(s):  
DAVID B. DE GRAAFF ◽  
JOHN K. EATON
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Turbulent Boundary Layer ◽  
Flat Plate ◽  
Extensive Study ◽  
Reynolds Stresses ◽  
Mean Flow ◽  
Mean Velocity ◽  
Law Of The Wall ◽  
The Mean

Despite extensive study, there remain significant questions about the Reynolds-number scaling of the zero-pressure-gradient flat-plate turbulent boundary layer. While the mean flow is generally accepted to follow the law of the wall, there is little consensus about the scaling of the Reynolds normal stresses, except that there are Reynolds-number effects even very close to the wall. Using a low-speed, high-Reynolds-number facility and a high-resolution laser-Doppler anemometer, we have measured Reynolds stresses for a flat-plate turbulent boundary layer from Reθ = 1430 to 31 000. Profiles of u′2, v′2, and u′v′ show reasonably good collapse with Reynolds number: u′2 in a new scaling, and v′2 and u′v′ in classic inner scaling. The log law provides a reasonably accurate universal profile for the mean velocity in the inner region.

Influence of Wall Proximity on the Wake Dynamics Behind a Square Cylinder

2021 ◽  
Author(s):  
Samuel Addai ◽  
Afua A. Mante ◽  
Sedem Kumahor ◽  
Xingjun Fang ◽  
Mark F. Tachie
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Normal Stress ◽  
Reynolds Shear Stress ◽  
Stream Velocity ◽  
Reynolds Stresses ◽  
Square Cylinder ◽  
Mean Flow ◽  
The Mean ◽  
Wall Proximity

Abstract In the present study, the effects of wall proximity on the wake dynamics behind a square cylinder subjected to a thick upstream turbulent boundary layer were experimentally investigated using particle image velocimetry. The Reynolds number based on the free-stream velocity and the cylinder height (h) was 12750 while the ratio of the turbulent boundary layer thickness to the cylinder height was 3.6. The gap distance (G) between the bottom face of the cylinder and the wall was varied, resulting in gap ratios (G/h) of 0, 0.3, 0.5, 1.0, 2.0 and 8.0. The flow topological differences among the various gap ratios were analyzed in terms of the mean flow and Reynolds stresses. The results show that as the cylinder approaches the wall, the mean flow becomes increasingly asymmetric about the horizontal centerline of the cylinder and the size of the mean separation bubbles in the cylinder wake increases. Also, the magnitudes of the Reynolds stresses decrease with decreasing gap ratio. For G/h > 0, the distributions of the streamwise Reynolds normal stress and Reynolds shear stress are concentrated along the upper and lower separated shear layers, resulting in characteristic double peaks. The distributions of the vertical Reynolds normal stress, however, are concentrated in the wake about the horizontal centerline of the cylinder and reveal only single peaks.

Data Analysis Methods for Stereo PIV of a High Aspect Ratio Flexible Cylinder

2007 ◽  
Author(s):  
D. Furey ◽  
P. Atsavapranee ◽  
K. Cipolla
Keyword(s):  
Boundary Layer ◽  
Data Analysis ◽  
Aspect Ratio ◽  
High Aspect Ratio ◽  
Particle Image Velocimetry Data ◽  
Flow Fields ◽  
Mean Flow ◽  
Boundary Flow ◽  
The Mean ◽  
Cylinder Flow

Stereo Particle Image velocimetry data was collected over high aspect ratio flexible cylinders (L/a = 1.5 to 3 × 105) to evaluate the axial development of the turbulent boundary layer where the boundary layer thickness becomes significantly larger than the cylinder diameter (δ/a>>1). The flexible cylinders are approximately neutrally buoyant and have an initial length of 152 m and radii of 0.45 mm and 1.25 mm. The cylinders were towed at speeds ranging from 3.8 to 15.4 m/sec in the David Taylor Model Basin. The analysis of the SPIV data required a several step procedure to evaluate the cylinder boundary flow. First, the characterization of the flow field from the towing strut is required. This evaluation provides the residual mean velocities and turbulence levels caused by the towing hardware at each speed and axial location. These values, called tare values, are necessary for comparing to the cylinder flow results. Second, the cylinder flow fields are averaged together and the averaged tare fields are subtracted out to remove strut-induced ambient flow effects. Prior to averaging, the cylinder flow fields are shifted to collocate the cylinder within the field. Since the boundary layer develops slowly, all planes of data occurring within each 10 meter increment of the cylinder length are averaged together to produce the mean boundary layer flow. Corresponding fields from multiple runs executed using the same experimental parameters are also averaged. This flow is analyzed to evaluate the level of axisymmetry in the data and determine if small changes in cylinder angle affect the mean flow development. With axisymmetry verified, the boundary flow is further averaged azimuthally around the cylinder to produce mean boundary layer profiles. Finally, the fluctuating velocity levels are evaluated for the flow with the cylinder and compared to the fluctuating velocity levels in the tare data. This paper will first discuss the data analysis techniques for the tare data and the averaging methods implemented. Second, the data analysis considerations will be presented for the cylinder data and the averaging and cylinder tracking techniques. These results are used to extract relevant boundary layer parameters including δ, δ* and θ. Combining these results with wall shear and momentum thickness values extracted from averaged cylinder drag data, the boundary layer can be well characterized.

Turbulent Wall-Pressure Fluctuations: A New Model for Off-Axis Cross-Spectral Density

1997 ◽  
Vol 119 (2) ◽  
pp. 277-280 ◽  
Author(s):  
B. A. Singer
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Spectral Density ◽  
Flow Direction ◽  
Wall Pressure ◽  
Mean Flow ◽  
New Approach ◽  
Cross Spectral Density ◽  
The Mean ◽  
The Cross

Models for the distribution of the wall-pressure under a turbulent boundary layer often estimate the coherence of the cross-spectral density in terms of a product of two coherence functions. One such function describes the coherence as a function of separation distance in the mean-flow direction, the other function describes the coherence in the cross-stream direction. Analysis of data from a large-eddy simulation of a turbulent boundary layer reveals that this approximation dramatically underpredicts the coherence for separation directions that are neither aligned with nor perpendicular to the mean-flow direction. These models fail even when the coherence functions in the directions parallel and perpendicular to the mean flow are known exactly. A new approach for combining the parallel and perpendicular coherence functions is presented. The new approach results in vastly improved approximations for the coherence.

Generation mechanism of a hierarchy of vortices in a turbulent boundary layer

2019 ◽  
Vol 865 ◽  
pp. 1085-1109 ◽  
Author(s):  
Yutaro Motoori ◽  
Susumu Goto
Keyword(s):  
Boundary Layer ◽  
Reynolds Number ◽  
Energy Spectrum ◽  
Turbulent Boundary Layer ◽  
Large Scale ◽  
Generation Mechanism ◽  
Small Scale ◽  
Generation Process ◽  
Mean Flow ◽  
The Mean

To understand the generation mechanism of a hierarchy of multiscale vortices in a high-Reynolds-number turbulent boundary layer, we conduct direct numerical simulations and educe the hierarchy of vortices by applying a coarse-graining method to the simulated turbulent velocity field. When the Reynolds number is high enough for the premultiplied energy spectrum of the streamwise velocity component to show the second peak and for the energy spectrum to obey the$-5/3$power law, small-scale vortices, that is, vortices sufficiently smaller than the height from the wall, in the log layer are generated predominantly by the stretching in strain-rate fields at larger scales rather than by the mean-flow stretching. In such a case, the twice-larger scale contributes most to the stretching of smaller-scale vortices. This generation mechanism of small-scale vortices is similar to the one observed in fully developed turbulence in a periodic cube and consistent with the picture of the energy cascade. On the other hand, large-scale vortices, that is, vortices as large as the height, are stretched and amplified directly by the mean flow. We show quantitative evidence of these scale-dependent generation mechanisms of vortices on the basis of numerical analyses of the scale-dependent enstrophy production rate. We also demonstrate concrete examples of the generation process of the hierarchy of multiscale vortices.

Subsonic Turbulent Flow Past a Planar Fence

1979 ◽  
Vol 101 (3) ◽  
pp. 373-375
Author(s):  
M. L. Agarwal ◽  
P. K. Pande ◽  
Rajendra Prakash
Keyword(s):  
Boundary Layer ◽  
Turbulent Boundary Layer ◽  
Flow Field ◽  
Boundary Conditions ◽  
Mean Flow ◽  
Governing Equations ◽  
Flow Past ◽  
Entire Flow ◽  
The Mean ◽  
Shape And Size

The mean flow past a fence submerged in a turbulent boundary layer is numerically simulated. The governing equations have been simplified by neglecting the convective effects of turbulence and solved numerically using experimental boundary conditions. The information obtained includes the shape and size of the upstream and downstream separation bubbles and the streamline pattern in the entire flow field. General agreement between the simulated and the experimental flow field was found.

Sign in / Sign up

Export Citation Format

Share Document