A Deep Insight Into the Transonic Flow of an Advanced Centrifugal Compressor Design

2020 ◽  
Vol 142 (9) ◽  
Author(s):  
David Wittrock ◽  
Martin Junker ◽  
Manfred Beversdorff ◽  
Andreas Peters ◽  
Eberhard Nicke
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Navier Stokes ◽  
Free Form ◽  
Numerical Verification ◽  
Deep Insight ◽  
Compressor Design ◽  
Design Speed

Abstract In the last decades, major improvements in transonic centrifugal compressor design have been achieved. The further exploration of design space is enabled by recent progress in structural mechanics and manufacturing. A challenging task of inducer design especially in terms of transonic inflow conditions is to provide a wide flow range and reduced losses due to a sufficient shock control. The use of so-called multidisciplinary design optimization with an extensive amount of free parameters leads finally to complex designs. DLR’s latest fast rotating centrifugal compressor (SRV5) operates at a design speed of Mu2 = 1.72 and a total pressure ratio of 5.72. This compressor design is characterized by an S-shaped leading edge and free-form blade surfaces. Due to the complex design, the key design features are difficult to explore. Therefore, nonintrusive measurements are conducted on the highly loaded SRV5. The laser-2-focus (L2F) approach that is used in addition with the doppler-global-velocimetry (DGV) delivers a three-dimensional velocity field. Besides the impeller inflow, the outflow is also part of the experimental and numerical verification of the advanced compressor design. Experimental results are compared with the numerical analysis of the compressor using DLR’s Reynolds-averaged Navier–Stokes Flow Solver TRACE. The deep insight of the inflow leads to a better understanding of the operating behavior of such impeller designs.

A Deep Insight Into the Transonic Flow of an Advanced Centrifugal Compressor Design

2019 ◽  
Author(s):  
D. Wittrock ◽  
M. Junker ◽  
M. Beversdorff ◽  
A. Peters ◽  
E. Nicke
Keyword(s):  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Free Form ◽  
Numerical Verification ◽  
Deep Insight ◽  
Flow Solver ◽  
Compressor Design ◽  
Design Speed

Abstract In the last decades major improvements in transonic centrifugal compressor design have been achieved. The further exploration of design space is enabled by recent progress in structural mechanics and manufacturing. A challenging task of inducer design especially in terms of transonic inflow conditions is to provide a wide flow range and reduced losses due to a sufficient shock control. The use of so called multidisciplinary design optimization with an extensive amount of free parameters leads finally to complex designs. DLR’s latest Fast Rotating Centrifugal Compressor (SRV5) operates at a design speed of Mu2 = 1.72 and a total pressure ratio of 5.72. This compressor design is characterized by an S-shaped leading edge and free-form blade surfaces. Due to the complex design the key design features are difficult to explore. Therefore, non-intrusive measurements are conducted on the highly loaded SRV5. The Laser-2-Focus (L2F) approach that is used in addition with the Doppler Global Velocimetry (DGV) delivers a three dimensional velocity field. Besides the impeller inflow the ouflow is also part of the experimental and numerical verification of the advanced compressor design. Experimental results are compared with the numerical analysis of the compressor using DLR’s RANS Flow Solver TRACE. The deep insight of the inflow leads to a better understanding of the operating behavior of such impeller designs.

Design and Experimental Study on the Surge Performance Improvement by the Effects of Bleed Slot Casing of a Centrifugal Compressor

2014 ◽  
Author(s):  
Hong Won Kim ◽  
Jae Hoon Chung ◽  
Hyo Seong Lee ◽  
Min Ouk Choi
Keyword(s):  
Centrifugal Compressor ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Design Parameters ◽  
Navier Stokes Equations ◽  
Operating Range ◽  
Surge Margin ◽  
Commercial Code

The primary design goal of a compressor is focused on improving efficiency. Secondary objective is to widen the compressor’s operating range. This paper presents a numerical and experimental investigation of the influence of the bleed slot to enlarge operating range for the 1.2MW class centrifugal compressor installed in a turbocharger. The main design parameters of the bleed slot casing are upstream slot position, inlet pipe slope, downstream slot position and width. The DOE (design of experiment) method was carried out to optimize the casing design. Numerical analyses were done by the commercial code ANSYS-CFX based on the three dimensional Reynolds-averaged Navier-Stokes equations. From the analysis, as the downstream slot position and width are smaller and upstream position is located away from impeller inlet, efficiency and pressure ratio are increased. Experimental works were done with and without the bleed slot casing. The simulation results were in good agreement with the test data. In case without the bleed slot casing, the surge margin value came out to be only 11.8% but with the optimized bleed slot design, the surge margin reached 23%. Therefore, the surge margin increase of 11.2% was achieved.

scholarly journals Aeroloads and Secondary Flows in a Transonic Mixed Flow Turbine Stage

1992 ◽  
Author(s):  
K. R. Kirtley ◽  
T. A. Beach ◽  
Cass Rogo
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Navier Stokes ◽  
Design System ◽  
Turbine Stage ◽  
Mixed Flow ◽  
Nozzle Vane ◽  
Highly Loaded

A numerical simulation of a transonic mixed flow turbine stage has been carried out using an average passage Navier-Stokes analysis. The mixed flow turbine stage considered here consists of a transonic nozzle vane and a highly loaded rotor. The simulation was run at the design pressure ratio and is assessed by comparing results with those of an established throughflow design system. The three-dimensional aerodynamic loads are studied as well as the development and migration of secondary flows and their contribution to the total pressure loss. The numerical results indicate that strong passage vortices develop in the nozzle vane, mix out quickly, and have little impact on the rotor flow. The rotor is highly loaded near the leading edge. Within the rotor passage, strong spanwise flows and other secondary flows exist along with the tip leakage vortex. The rotor exit loss distribution is similar in character to that found in radial inflow turbines. The secondary flows and non-uniform work extraction also tend to significantly redistribute a non-uniform inlet total temperature profile by the exit of the stage.

Experimental and Numerical Investigation of a Centrifugal Compressor and Numerical Study of the Area Ratio and Tip Clearance Effects on the Performance Characteristic

2008 ◽  
Author(s):  
Mahdi Nili-Ahmadabadi ◽  
Ali Hajilouy-Benisi ◽  
Mohammad Durali ◽  
Sayyed Mostafa Motavalli
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Numerical Study ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Area Ratio ◽  
Tip Clearance ◽  
Performance Characteristics ◽  
Navier Stokes ◽  
Sst Turbulence Model

In this research, the centrifugal compressor of a turbocharger is investigated experimentally and numerically. Performance characteristics of the compressor were obtained experimentally by measurements of rotor speed and flow parameters at the inlet and outlet of the compressor. Three dimensional flow field in the impeller and diffuser was analyzed numerically using a full Navier-Stokes program with SST turbulence model. The performance characteristics of the compressor were obtained numerically, which were then compared with the experimental results. The comparison shows good agreement. Furthermore, the effect of area ratio and tip clearance on the performance parameters and flow field was studied numerically. The impeller area ratio was changed by cutting the impeller exit axial width from an initial value of 4.1 mm to a final value of 5.1 mm, resulting in an area ratio from 0.792 to 0.965. For the rotor with exit axial width of 4.6 mm, performance was investigated for tip clearance of 0.0, 0.5 and 1.0 mm. Results of this simulation at design point showed that the compressor pressure ratio peaked at an area ratio of 0.792 while the efficiency peaked at a higher value of area ratio of 0.878. Also the increment of the tip clearance from 0 to 1 mm resulted in 20 percent efficiency decrease.

CFD Analysis of a Centrifugal Compressor Impeller and Volute

1999 ◽  
Author(s):  
Harri Pitkänen ◽  
Hannu Esa ◽  
Petri Sallinen ◽  
Jaakko Larjola
Keyword(s):  
Centrifugal Compressor ◽  
Static Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Prediction Method ◽  
Navier Stokes ◽  
Recovery Coefficient ◽  
Compressor Impeller ◽  
Compressor Performance ◽  
Pressure Recovery Coefficient

In this study, centrifugal compressor performance was predicted using CFD. Three-dimensional time-averaged impeller and volute simulations were performed using a Navier–Stokes code. The presented performance prediction method has been divided into three phases. Firstly, the impeller was calculated with a vaneless diffuser. That gives inlet boundary conditions for the volute analysis and the pressure ratio at the diffuser exit. Next, the volute analysis was performed and a static pressure recovery coefficient obtained. Finally, that result was combined with the pressure ratio prediction from the impeller analysis, and the overall compressor performance thus obtained.

Aerodynamic Performances of a Centrifugal Compressor With Discrete Cavities

2017 ◽  
Author(s):  
Sang-Bum Ma ◽  
Kwang-Yong Kim
Keyword(s):  
Centrifugal Compressor ◽  
Stokes Equations ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Stall Margin ◽  
Tetrahedral Grid ◽  
Aerodynamic Performances ◽  
Inclined Angle

In this study, aerodynamic performance of the centrifugal compressor was investigated by using a recirculating device called discrete cavities. A parametric study was conducted using six parameters related to the geometry of the discrete cavities, i.e., the inclined angle, the port angle and width, the length of cavity, the axial location of each cavity, and the number of cavities. Three-dimensional Reynolds-averaged Navier-Stokes equations with shear stress transport turbulence model were used for aerodynamic analysis of the centrifugal compressor with discrete cavities. The hexahedral grid was used in impeller domain and tetrahedral grid was used in volute and inclined discrete cavities. The numerical results for the adiabatic efficiency and the total pressure ratio (inlet to outlet) showed good agreements with experimental data. It was found that inclination of the discrete cavities further increased the stall margin without loss of efficiency compared to the uninclined discrete cavities.

Design of a Highly Loaded Transonic Two-Stage Fan Using Swept and Bowed Blading

2011 ◽  
Author(s):  
Hailiang Jin ◽  
Donghai Jin ◽  
Fang Zhu ◽  
Ke Wan ◽  
Xingmin Gui
Keyword(s):  
Total Pressure ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Navier Stokes ◽  
Two Stage ◽  
Stall Margin ◽  
Stator Vane ◽  
Total Pressure Ratio ◽  
Highly Loaded

This paper presents the design of a highly loaded transonic two-stage fan using several advanced three-dimensional blading techniques including forward sweep and “hub bending” in rotors and several bowed configurations in stators. The effects of these blading techniques on the performance of the highly loaded transonic two-stage fan were investigated on the basis of three-dimensional Navier-Stokes predictions. The results indicate that forward sweep has insignificant impact on the total pressure ratio and adiabatic efficiency of the fan. The throttling range of the fan is found to be improved by forward sweep because the shock in the forward swept rotor is expelled later upstream to the leading edge than that in the unswept one. Hub bending design technique increases the efficiency in the hub region of R1 due to the reduction of the low momentum zone in the hub region near the trailing edge. The stator vane design has a pronounced impact on the performance of the fan. The total pressure ratio, adiabatic efficiency, and stall margin of the schemes with the bowed vanes are increased significantly compared to the scheme with the straight vanes. The large corner stall in the straight S1 vane is reduced effectively by the bowed S1 vanes. Moreover, the strong corner stall in the straight S2 vane is fully eliminated by the bowed S2 vanes. Among the bowed vane schemes, the scheme with positive bowed (P. B.) hub and negative bowed (N. B.) tip vanes has the best efficiency and stall margin performances thanks to the superiority of the performance over the midspan regions of the bowed vanes.

Numerical Analysis of the Vaned Diffuser of a Transonic Centrifugal Compressor

2010 ◽  
Vol 132 (4) ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
High Pressure Ratio ◽  
Unsteady Interaction ◽  
Inlet Conditions

A three-dimensional Navier–Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vaned diffuser. Particular attention is focused on the analysis of the vaned diffuser, designed for high subsonic inlet conditions. The diffuser is characterized by a complex three-dimensional flow field and influenced by the unsteady interaction with the impeller. Detailed particle image velocimetry flow measurements within the diffuser are available for comparison purposes.

Numerical Analysis of the Vaned Diffuser of a Transonic Centrifugal Compressor

2007 ◽  
Author(s):  
Michele Marconcini ◽  
Filippo Rubechini ◽  
Andrea Arnone ◽  
Seiichi Ibaraki
Keyword(s):  
Flow Field ◽  
Centrifugal Compressor ◽  
Pressure Ratio ◽  
Three Dimensional ◽  
Navier Stokes ◽  
Flow Measurements ◽  
Vaned Diffuser ◽  
High Pressure Ratio ◽  
Unsteady Interaction ◽  
Inlet Conditions

A three-dimensional Navier-Stokes solver is used to investigate the flow field of a high pressure ratio centrifugal compressor for turbocharger applications. Such a compressor consists of a double-splitter impeller followed by a vaned diffuser. Particular attention is focused on the analysis of the vaned diffuser, designed for high subsonic inlet conditions. The diffuser is characterized by a complex three-dimensional flow field, and influenced by the unsteady interaction with the impeller. Detailed Particle Image Velocimetry (PIV) flow measurements within the diffuser are available for comparison purposes.

Aeroloads and Secondary Flows in a Transonic Mixed-Flow Turbine Stage

1993 ◽  
Vol 115 (3) ◽  
pp. 590-600 ◽  
Author(s):  
K. R. Kirtley ◽  
T. A. Beach ◽  
C. Rogo
Keyword(s):  
Pressure Ratio ◽  
Three Dimensional ◽  
Leading Edge ◽  
Secondary Flows ◽  
Navier Stokes ◽  
Design System ◽  
Turbine Stage ◽  
Mixed Flow ◽  
Nozzle Vane ◽  
Highly Loaded

A numerical simulation of a transonic mixed-flow turbine stage has been carried out using an average passage Navier–Stokes analysis. The mixed-flow turbine stage considered here consists of a transonic nozzle vane and a highly loaded rotor. The simulation was run at the design pressure ratio and is assessed by comparing results with those of an established throughflow design system. The three-dimensional aerodynamic loads are studied as well as the development and migration of secondary flows and their contribution to the total pressure loss. The numerical results indicate that strong passage vortices develop in the nozzle vane, mix out quickly, and have little impact on the rotor flow. The rotor is highly loaded near the leading edge. Within the rotor passage, strong spanwise flows and other secondary flows exist along with the tip leakage vortex. The rotor exit loss distribution is similar in character to that found in radial inflow turbines. The secondary flows and nonuniform work extraction also tend to redistribute a nonuniform inlet total temperature profile significantly by the exit of the stage.

Sign in / Sign up

Export Citation Format

Share Document