Subsidence of Additively-Manufactured Cages in Foam Substrates: Effect of Contact Topology

2020 ◽  
Vol 142 (9) ◽  
Author(s):  
Rachel R. Collino ◽  
Ali Kiapour ◽  
Matthew R. Begley
Keyword(s):  
Contact Area ◽  
Bone Structure ◽  
Three Dimensional ◽  
Line Contact ◽  
Contact Topology ◽  
Material Stiffness ◽  
3D Printed ◽  
Contact Size ◽  
Insight Into ◽  
Resistance To Penetration

Abstract Subsidence of implants into bone is a major source of morbidity. The underlying mechanics of the phenomenon are not clear, but are likely related to interactions between contact stresses and the underlying porous trabecular bone structure. To gain insight into these interactions, we studied the penetration of three-dimensional (3D)-printed indenters with systematically varying geometries into Sawbones® foam substrates and isolated the effects of contact geometry from those of overall contact size and area. When size, contact area, and indented material stiffness and strength are controlled for, we show that resistance to penetration is in fact a function of topology only. Indenters with greater line contact lengths support higher subsidence loads in compression. These results have direct implications for the design of implants to resist subsidence into bone.

scholarly journals Graphene-Reinforced Biodegradable Resin Composites for Stereolithographic 3D Printing of Bone Structure Scaffolds

2019 ◽  
Vol 2019 ◽  
pp. 1-13 ◽  
Author(s):  
Zuying Feng ◽  
Yan Li ◽  
Liang Hao ◽  
Yihu Yang ◽  
Tian Tang ◽  
...  
Keyword(s):  
Tissue Engineering ◽  
3D Printing ◽  
Bone Structure ◽  
Multistep Methods ◽  
Three Dimensional ◽  
Resin Composites ◽  
Polyurethane Resin ◽  
3D Printed ◽  
Reference Specimens ◽  
Bone Structures

A biodegradable UV-cured resin has been fabricated via stereolithography apparatus (SLA). The formulation consists of a commercial polyurethane resin as an oligomer, trimethylolpropane trimethacrylate (TEGDMA) as a reactive diluent and phenylbis (2, 4, 6-trimethylbenzoyl)-phosphine oxide (Irgacure 819) as a photoinitiator. The tensile strength of the three-dimensional (3D) printed specimens is 68 MPa, 62% higher than that of the reference specimens (produced by direct casting). The flexural strength and modulus can reach 115 MPa and 5.8 GPa, respectively. A solvent-free method is applied to fabricate graphene-reinforced nanocomposite. Porous bone structures (a jawbone with a square architecture and a sternum with a round architecture) and gyroid scaffold of graphene-reinforced nanocomposite for bone tissue engineering have been 3D printed via SLA. The UV-crosslinkable graphene-reinforced biodegradable nanocomposite using SLA 3D printing technology can potentially remove important cost barriers for personalized biological tissue engineering as compared to the traditional mould-based multistep methods.

scholarly journals Three-Dimensional Printing for Cancer Applications: Research Landscape and Technologies

2021 ◽  
Vol 14 (8) ◽  
pp. 787
Author(s):  
Ruixiu Li ◽  
Yu-Huan Ting ◽  
Souha H. Youssef ◽  
Yunmei Song ◽  
Sanjay Garg
Keyword(s):  
Drug Discovery ◽  
3D Printing ◽  
Three Dimensional ◽  
Three Dimensional Printing ◽  
Novel Technologies ◽  
Speed Up ◽  
Fundamental Research ◽  
3D Printed ◽  
Dimensional Printing ◽  
Insight Into

As a variety of novel technologies, 3D printing has been considerably applied in the field of health care, including cancer treatment. With its fast prototyping nature, 3D printing could transform basic oncology discoveries to clinical use quickly, speed up and even revolutionise the whole drug discovery and development process. This literature review provides insight into the up-to-date applications of 3D printing on cancer research and treatment, from fundamental research and drug discovery to drug development and clinical applications. These include 3D printing of anticancer pharmaceutics, 3D-bioprinted cancer cell models and customised nonbiological medical devices. Finally, the challenges of 3D printing for cancer applications are elaborated, and the future of 3D-printed medical applications is envisioned.

scholarly journals Fabrication of Biocompatible Polycaprolactone–Hydroxyapatite Composite Filaments for the FDM 3D Printing of Bone Scaffolds

2021 ◽  
Vol 11 (14) ◽  
pp. 6351
Author(s):  
Chang Geun Kim ◽  
Kyung Seok Han ◽  
Sol Lee ◽  
Min Cheol Kim ◽  
Soo Young Kim ◽  
...  
Keyword(s):  
3D Printing ◽  
Fused Deposition Modeling ◽  
Bone Structure ◽  
Three Dimensional ◽  
Tensile Tests ◽  
Raw Material ◽  
Fused Deposition ◽  
Bone Scaffolds ◽  
3D Printed ◽  
Mechanical Tensile

Recently, three-dimensional printing (3DP) technology has been widely adopted in biology and biomedical applications, thanks to its capacity to readily construct complex 3D features. Using hot-melt extrusion 3DP, scaffolds for bone tissue engineering were fabricated using a composite of biodegradable polycaprolactone (PCL) and hydroxyapatite (HA). However, there are hardly any published reports on the application of the fused deposition modeling (FDM) method using feed filaments, which is the most common 3D printing method. In this study, we report on the fabrication and characterization of biocompatible filaments made of polycaprolactone (PCL)/hydroxyapatite (HA), a raw material mainly used for bone scaffolds, using FDM 3D printing. A series of filaments with varying HA content, from 5 to 25 wt.%, were fabricated. The mechanical and electrical properties of the various structures, printed using a commercially available 3D printer, were examined. Specifically, mechanical tensile tests were performed on the 3D-printed filaments and specimens. In addition, the electrical dielectric properties of the 3D-printed structures were investigated. Our method facilitates the fabrication of biocompatible structures using FDM-type 3DP, creating not only bone scaffolds but also testbeds for mimicking bone structure that may be useful in various fields of study.

Structure and function of neural networks in the retina

1988 ◽  
Vol 46 ◽  
pp. 26-27
Author(s):  
Peter Sterling
Keyword(s):  
Ganglion Cells ◽  
Three Dimensional ◽  
Structure And Function ◽  
Synaptic Connections ◽  
Visual Axis ◽  
One Dimensional ◽  
Cat Retina ◽  
Ultrathin Sections ◽  
And Function ◽  
Insight Into

The synaptic connections in cat retina that link photoreceptors to ganglion cells have been analyzed quantitatively. Our approach has been to prepare serial, ultrathin sections and photograph en montage at low magnification (˜2000X) in the electron microscope. Six series, 100-300 sections long, have been prepared over the last decade. They derive from different cats but always from the same region of retina, about one degree from the center of the visual axis. The material has been analyzed by reconstructing adjacent neurons in each array and then identifying systematically the synaptic connections between arrays. Most reconstructions were done manually by tracing the outlines of processes in successive sections onto acetate sheets aligned on a cartoonist's jig. The tracings were then digitized, stacked by computer, and printed with the hidden lines removed. The results have provided rather than the usual one-dimensional account of pathways, a three-dimensional account of circuits. From this has emerged insight into the functional architecture.

Use of Three-dimensional Printing in the Development of Optimal Cardiac CT Scanning Protocols

2020 ◽  
Vol 16 (8) ◽  
pp. 967-977
Author(s):  
Zhonghua Sun
Keyword(s):  
Cardiovascular Disease ◽  
Cardiac Computed Tomography ◽  
Three Dimensional ◽  
Ct Scanning ◽  
Aortic Diseases ◽  
Clinical Value ◽  
Three Dimensional Printing ◽  
Doctor Patient Communication ◽  
Medical Education And Training ◽  
3D Printed

Three-dimensional (3D) printing is increasingly used in medical applications with most of the studies focusing on its applications in medical education and training, pre-surgical planning and simulation, and doctor-patient communication. An emerging area of utilising 3D printed models lies in the development of cardiac computed tomography (CT) protocols for visualisation and detection of cardiovascular disease. Specifically, 3D printed heart and cardiovascular models have shown potential value in the evaluation of coronary plaques and coronary stents, aortic diseases and detection of pulmonary embolism. This review article provides an overview of the clinical value of 3D printed models in these areas with regard to the development of optimal CT scanning protocols for both diagnostic evaluation of cardiovascular disease and reduction of radiation dose. The expected outcomes are to encourage further research towards this direction.

Investigation of the Static Behavior and Failure Mechanisms of a 3D Printed Bio-Based Sandwich with Auxetic Core

2020 ◽  
Vol 12 (05) ◽  
pp. 2050051
Author(s):  
Khawla Essassi ◽  
Jean-Luc Rebiere ◽  
Abderrahim El Mahi ◽  
Mohamed Amine Ben Souf ◽  
Anas Bouguecha ◽  
...  
Keyword(s):  
Failure Mechanisms ◽  
Three Dimensional ◽  
Acoustic Emissions ◽  
Shear Stiffness ◽  
Tensile Tests ◽  
Sandwich Composite ◽  
Static Behavior ◽  
Flax Fibers ◽  
Data Points ◽  
3D Printed

In this research contribution, the static behavior and failure mechanisms are developed for a three-dimensional (3D) printed dogbone, auxetic structure and sandwich composite using acoustic emissions (AEs). The skins, core and whole sandwich are manufactured using the same bio-based material which is polylactic acid reinforced with micro-flax fibers. Tensile tests are conducted on the skins and the core while bending tests are conducted on the sandwich composite. Those tests are carried out on four different auxetic densities in order to investigate their effect on the mechanical and damage properties of the materials. To monitor the invisible damage and damage propagation, a highly sensitive AE testing method is used. It is found that the sandwich with high core density displays advanced mechanical properties in terms of bending stiffness, shear stiffness, facing bending stress and core shear stress. In addition, the AE data points during testing present an amplitude range of 40–85[Formula: see text]dB that characterizes visible and invisible damage up to failure.

Thermomechanical Coupling of a Hyper-viscoelastic Truck Tire and a Pavement Layer and its Impact on Three-dimensional Contact Stresses

2021 ◽  
pp. 036119812110171
Author(s):  
Angeli Jayme ◽  
Imad L. Al-Qadi
Keyword(s):  
Contact Stress ◽  
Contact Area ◽  
Three Dimensional ◽  
Interaction Model ◽  
Rolling Resistance ◽  
Contact Stresses ◽  
Thermomechanical Coupling ◽  
Temperature Profiles ◽  
Near Surface ◽  
Truck Tire

A thermomechanical coupling between a hyper-viscoelastic tire and a representative pavement layer was conducted to assess the effect of various temperature profiles on the mechanical behavior of a rolling truck tire. The two deformable bodies, namely the tire and pavement layer, were subjected to steady-state-uniform and non-uniform temperature profiles to identify the significance of considering temperature as a variable in contact-stress prediction. A myriad of ambient, internal air, and pavement-surface conditions were simulated, along with combinations of applied tire load, tire-inflation pressure, and traveling speed. Analogous to winter, the low temperature profiles induced a smaller tire-pavement contact area that resulted in stress localization. On the other hand, under high temperature conditions during the summer, higher tire deformation resulted in lower contact-stress magnitudes owing to an increase in the tire-pavement contact area. In both conditions, vertical and longitudinal contact stresses are impacted, while transverse contact stresses are relatively less affected. This behavior, however, may change under a non-free-rolling condition, such as braking, accelerating, and cornering. By incorporating temperature into the tire-pavement interaction model, changes in the magnitude and distribution of the three-dimensional contact stresses were manifested. This would have a direct implication on the rolling resistance and near-surface behavior of flexible pavements.

scholarly journals Completely non-fused electron acceptor with 3D-interpenetrated crystalline structure enables efficient and stable organic solar cell

2021 ◽  
Vol 12 (1) ◽  
Author(s):  
Lijiao Ma ◽  
Shaoqing Zhang ◽  
Jincheng Zhu ◽  
Jingwen Wang ◽  
Junzhen Ren ◽  
...  
Keyword(s):  
Organic Solar Cell ◽  
Low Cost ◽  
Three Dimensional ◽  
Molecular Geometry ◽  
Interpenetrating Network ◽  
Fused Ring ◽  
Molecule Design ◽  
End Capping ◽  
Conversion Efficiencies ◽  
Insight Into

AbstractNon-fullerene acceptors (NFAs) based on non-fused conjugated structures have more potential to realize low-cost organic photovoltaic (OPV) cells. However, their power conversion efficiencies (PCEs) are much lower than those of the fused-ring NFAs. Herein, a new bithiophene-based non-fused core (TT-Pi) featuring good planarity as well as large steric hindrance was designed, based on which a completely non-fused NFA, A4T-16, was developed. The single-crystal result of A4T-16 reveals that a three-dimensional interpenetrating network can be formed due to the compact π–π stacking between the adjacent end-capping groups. A high PCE of 15.2% is achieved based on PBDB-TF:A4T-16, which is the highest value for the cells based on the non-fused NFAs. Notably, the device retains ~84% of its initial PCE after 1300 h under the simulated AM 1.5 G illumination (100 mW cm−2). Overall, this work provides insight into molecule design of the non-fused NFAs from the aspect of molecular geometry control.

scholarly journals Midface Reconstruction: Planning and Outcome

2020 ◽  
Vol 53 (03) ◽  
pp. 324-334
Author(s):  
Gautam Biswas
Keyword(s):  
Digital Imaging ◽  
3D Structure ◽  
Three Dimensional ◽  
The Past ◽  
Complex Anatomy ◽  
Osseointegrated Implants ◽  
Low Profile ◽  
3D Printed ◽  
Midface Reconstruction ◽  
Reconstruction Planning

Abstract Reconstruction of the complex anatomy and aesthetics of the midface is often a challenge. A careful understanding of this three-dimensional (3D) structure is necessary. Anticipating the extent of excision and its planning following oncological resections is critical.In the past over two decades, with the advances in microsurgical procedures, contributions toward the reconstruction of this area have generated interest. Planning using digital imaging, 3D printed models, osseointegrated implants, and low-profile plates, has favorably impacted the outcome. However, there are still controversies in the management: to use single composite tissues versus multiple tissues; implants versus autografts; vascularized versus nonvascularized bone; prosthesis versus reconstruction.This article explores the present available options in maxillary reconstruction and outlines the approach in the management garnered from past publications and experiences.

scholarly journals Recurrent contracted sockets treated with personalized, three-dimensionally printed conformers and buccal grafts

2021 ◽  
pp. 112067212110000
Author(s):  
Annabel LW Groot ◽  
Jelmer S Remmers ◽  
Roel JHM Kloos ◽  
Peerooz Saeed ◽  
Dyonne T Hartong
Keyword(s):  
Three Dimensional ◽  
Case Series ◽  
Secondary Outcome ◽  
Retrospective Case ◽  
Upper Eyelid ◽  
Ocular Prosthesis ◽  
Buccal Mucosal Graft ◽  
Custom Made ◽  
3D Printed

Purpose: Recurrent contracted sockets are complex situations where previous surgeries have failed, disabling the wear of an ocular prosthesis. A combined method of surgery and long-term fixation using custom-made, three-dimensional (3D) printed conformers is evaluated. Methods: Retrospective case series of nine patients with recurrent excessive socket contraction and inability to wear a prosthesis, caused by chemical burns ( n = 3), fireworks ( n = 3), trauma ( n = 2) and enucleation and radiotherapy at childhood due to optic nerve glioma ( n = 1) with three average previous socket surgeries (range 2–6). Treatment consisted of a buccal mucosal graft and personalized 3D-printed conformer designed to be fixated to the periosteum and tarsal plates for minimal 2 months. Primary outcome was the retention of an ocular prosthesis. Secondary outcome was the need for additional surgeries. Results: Outcomes were measured at final follow-up between 7 and 36 months postoperatively (mean 20 months). Eight cases were able to wear an ocular prosthesis after 2 months. Three cases initially treated for only the upper or only the lower fornix needed subsequent surgery for the opposite fornix for functional reasons. Two cases had later surgery for cosmetic improvement of upper eyelid position. Despite pre-existing lid abnormalities (scar, entropion, lash deficiency), cosmetic outcome was judged highly acceptable in six cases because of symmetric contour and volume, and reasonably acceptable in the remaining two. Conclusions: Buccal mucosal transplant fixated with a personalized 3D-designed conformer enables retention of a well-fitted ocular prosthesis in previously failed socket surgeries. Initial treatment of both upper and lower fornices is recommended to avoid subsequent surgeries for functional reasons.

Sign in / Sign up

Export Citation Format

Share Document