Estimating Laminar Flame Speed and Ignition Delay for a Series of Natural Gas Mixtures at IC Engine-Relevant Conditions

2019 ◽  
Vol 142 (6) ◽  
Author(s):  
Kelsey Fieseler ◽  
Taylor Linker ◽  
Mark Patterson ◽  
Daniel Rem ◽  
Timothy J. Jacobs
Keyword(s):  
Natural Gas ◽  
Ignition Delay ◽  
Laminar Flame ◽  
Initial Conditions ◽  
Initial Pressure ◽  
Fuel Mixture ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Ic Engine ◽  
The Impact

Abstract Two equations are developed to estimate laminar flame speed and ignition delay for different alkane mixtures at a range of engine-relevant conditions. Fuel mixtures of methane, ethane, propane, butane, and pentane were selected by analyzing the natural gas composition in a natural gas pipeline located in the Midwestern United States. The laminar flame speed and ignition delay were calculated for each mixture at each set of conditions using Cantera, a chemical kinetics solver. The range of initial conditions for laminar flame speed includes temperatures from 300 to 700 K, pressures from 1 to 40 bar, equivalence ratios from 0.4 to 1.2, and residual fractions from 0% to 20%. These data were then fit to a non-linear regression. The range of initial conditions for the ignition delay equation includes temperatures from 1100 to 2000 K, pressures from 1 to 40 bar, equivalence ratios from 0.4 to 1.15, and residual fractions from 0% to 20%. These data were fit to a previously developed equation. Sensitivity studies were conducted on each equation to quantify the impact of the independent variables on the target variable. This showed that, for laminar flame speed, the initial pressure, temperature, and equivalence ratio had the largest impact, with fuel composition having a lesser impact. For ignition delay, the temperature and pressure were shown to have the largest impact. There is a room for improvement, namely, increasing the fuel mixture variability and range of initial conditions, and developing a better fit to the data.

Ignition Delay Time and Laminar Flame Speed Calculations for Natural Gas/Hydrogen Blends at Elevated Pressures

2012 ◽  
Author(s):  
Marissa Brower ◽  
Eric Petersen ◽  
Wayne Metcalfe ◽  
Henry J. Curran ◽  
Marc Füri ◽  
...  
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Hydrogen Addition

Applications of natural gas and hydrogen co-firing have received increased attention in the gas turbine market, which aims at higher flexibility due to concerns over the availability of fuels. While much work has been done in the development of a fuels database and corresponding chemical kinetics mechanism for natural gas mixtures, there are nonetheless few if any data for mixtures with high levels of hydrogen at conditions of interest to gas turbines. The focus of the present paper is on gas turbine engines with primary and secondary reaction zones as represented in the Alstom and Rolls Royce product portfolio. The present effort includes a parametric study, a gas turbine model study, and turbulent flame speed predictions. Using a highly optimized chemical kinetics mechanism, ignition delay times and laminar burning velocities were calculated for fuels from pure methane to pure hydrogen and with natural gas/hydrogen mixtures. A wide range of engine-relevant conditions were studied: pressures from 1 to 30 atm, flame temperatures from 1600 to 2200 K, primary combustor inlet temperature from 300 to 900 K, and secondary combustor inlet temperatures from 900 to 1400 K. Hydrogen addition was found to increase the reactivity of hydrocarbon fuels at all conditions by increasing the laminar flame speed and decreasing the ignition delay time. Predictions of turbulent flame speeds from the laminar flame speeds show that hydrogen addition affects the reactivity more when turbulence is considered. This combined effort of industrial and university partners brings together the know-how of applied, as well as experimental and theoretical disciplines.

scholarly journals Comparative Study on Chemical Kinetics Mechanisms for Methane-Based Fuel Mixtures under Engine-Relevant Conditions

Energies ◽  
2021 ◽  
Vol 14 (10) ◽  
pp. 2834
Author(s):  
Amin Paykani
Keyword(s):  
Experimental Data ◽  
Natural Gas ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
High Pressures ◽  
Laminar Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Si Engine ◽  
Fuel Blends

The use of natural gas in pure or in a blended form with hydrogen and syngas in spark ignition (SI) engines has received much attention in recent years. They have higher diffusion coefficient and laminar flame speed, a small quenching distance and wider flammability limit which compensate the demerits of the lean-burn natural gas combustion. Therefore, a careful examination of the chemical kinetics of combustion of gaseous fuel blends is of great importance. In this paper, performance of the various chemical kinetics mechanisms is compared against experimental data, accumulated for methane-based fuel blends under engine-relevant conditions to find the most appropriate mechanism in engine simulations. Pure methane, methane/syngas, and methane/propane blends are mainly studied at various temperatures, pressures, and equivalence ratios. The ignition delay time and laminar flame speed are used as quantitative metrics to compare the simulation results with the data from experiments. The mechanisms were shown to be mainly consistent with the experimental data of lean and stoichiometric mixtures at high pressures. It was also shown that the GRI-3.0 and 290Rxn mechanisms have high compatibility with the ignition delay times and laminar flame speed at high pressures and lean conditions, and they can be utilized for simulations of SI engine combustion due to their lower computational cost. The results of present research provide an important contribution to the methane-based fuel blends combustion simulation under SI engine-relevant conditions.

scholarly journals Effects of oil and water contamination on natural gas engine combustion processes

2017 ◽  
Author(s):  
Shyam Menon ◽  
Himakar Ganti ◽  
Kyle Evan Niemeyer ◽  
Christopher Hagen
Keyword(s):  
Natural Gas ◽  
Ignition Delay ◽  
Laminar Flame ◽  
Combustion Process ◽  
Flame Speed ◽  
Slight Reduction ◽  
Laminar Flame Speed ◽  
Autoignition Temperature ◽  
Engine Combustion ◽  
Combustion Processes

Abundant availability and potential for lower emissions are drivers for increased utilization of natural gas in automotive engines for transportation applications. A novel bimodal engine has been developed that allows on-board refueling of natural gas by utilizing the engine as a compressor. Engine compression however, results in altering the initial state of the natural gas. Increase in temperature and addition of oil are two key effects attributed to the onboard refueling process. A secondary effect is the presence of water in the natural gas supply line. This study investigates the effect of upstream conditions of natural gas on three parameters: autoignition temperature, ignition delay, and laminar flame speed. These parameters play key roles in the engine combustion process. Parametric studies are conducted by varying the initial mixture temperature, water, and oil content in the fuel. The studies utilize numerical simulations conducted with detailed chemistry for natural gas with n-heptane used as a surrogate for oil. Water addition to natural gas at 1–5% by volume did not result in any major changes in the combustion processes, other than a slight reduction in laminar flame speeds. Oil addition of 1–5% by volume reduced autoignition temperature by 5–10% and ignition delay by 27–95% depending on the initial temperature. Sensitivity analysis showed that this was likely due to decrease in the sensitivity of two recombination reactions with oil addition. Evolution profiles of key radical species also showed increasing mole fraction of the hydroperoxy radical at lower temperature that likely aids in reducing the ignition delay. Oil addition resulted in a relatively small increase in the laminar flame speed of 1.7% along with an increase in the adiabatic flame temperature. These results help inform the combustion process and performance to be expected from the bimodal engine.

Ignition Delay Time and Laminar Flame Speed Calculations for Natural Gas/Hydrogen Blends at Elevated Pressures

2013 ◽  
Vol 135 (2) ◽  
Author(s):  
Marissa Brower ◽  
Eric L. Petersen ◽  
Wayne Metcalfe ◽  
Henry J. Curran ◽  
Marc Füri ◽  
...  
Keyword(s):  
Natural Gas ◽  
Gas Turbine ◽  
Chemical Kinetics ◽  
Ignition Delay ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Turbulent Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Hydrogen Addition

Applications of natural gas and hydrogen co-firing have received increased attention in the gas turbine market, which aims at higher flexibility due to concerns over the availability of fuels. While much work has been done in the development of a fuels database and corresponding chemical kinetics mechanism for natural gas mixtures, there are nonetheless few if any data for mixtures with high levels of hydrogen at conditions of interest to gas turbines. The focus of the present paper is on gas turbine engines with primary and secondary reaction zones as represented in the Alstom and Rolls Royce product portfolio. The present effort includes a parametric study, a gas turbine model study, and turbulent flame speed predictions. Using a highly optimized chemical kinetics mechanism, ignition delay times and laminar burning velocities were calculated for fuels from pure methane to pure hydrogen and with natural gas/hydrogen mixtures. A wide range of engine-relevant conditions were studied: pressures from 1 to 30 atm, flame temperatures from 1600 to 2200 K, primary combustor inlet temperature from 300 to 900 K, and secondary combustor inlet temperatures from 900 to 1400 K. Hydrogen addition was found to increase the reactivity of hydrocarbon fuels at all conditions by increasing the laminar flame speed and decreasing the ignition delay time. Predictions of turbulent flame speeds from the laminar flame speeds show that hydrogen addition affects the reactivity more when turbulence is considered. This combined effort of industrial and university partners brings together the know-how of applied as well as experimental and theoretical disciplines.

Laminar flame speed correlations for methane, ethane, propane and their mixtures, and natural gas and gasoline for spark-ignition engine simulations

2017 ◽  
Vol 18 (9) ◽  
pp. 951-970 ◽  
Author(s):  
Riccardo Amirante ◽  
Elia Distaso ◽  
Paolo Tamburrano ◽  
Rolf D Reitz
Keyword(s):  
Natural Gas ◽  
Laminar Flame ◽  
Spark Ignition ◽  
Flame Speed ◽  
Operating Conditions ◽  
Spark Ignition Engine ◽  
Computational Time ◽  
Laminar Flame Speed ◽  
Spark Ignition Engines ◽  
Empirical Correlations

The laminar flame speed plays an important role in spark-ignition engines, as well as in many other combustion applications, such as in designing burners and predicting explosions. For this reason, it has been object of extensive research. Analytical correlations that allow it to be calculated have been developed and are used in engine simulations. They are usually preferred to detailed chemical kinetic models for saving computational time. Therefore, an accurate as possible formulation for such expressions is needed for successful simulations. However, many previous empirical correlations have been based on a limited set of experimental measurements, which have been often carried out over a limited range of operating conditions. Thus, it can result in low accuracy and usability. In this study, measurements of laminar flame speeds obtained by several workers are collected, compared and critically analyzed with the aim to develop more accurate empirical correlations for laminar flame speeds as a function of equivalence ratio and unburned mixture temperature and pressure over a wide range of operating conditions, namely [Formula: see text], [Formula: see text] and [Formula: see text]. The purpose is to provide simple and workable expressions for modeling the laminar flame speed of practical fuels used in spark-ignition engines. Pure compounds, such as methane and propane and binary mixtures of methane/ethane and methane/propane, as well as more complex fuels including natural gas and gasoline, are considered. A comparison with available empirical correlations in the literature is also provided.

Evaluation of Kinetic Mechanisms for Direct Fired Supercritical Oxy-Combustion of Natural Gas

2016 ◽  
Author(s):  
Shane Coogan ◽  
Xiang Gao ◽  
Aaron McClung ◽  
Wenting Sun
Keyword(s):  
Carbon Dioxide ◽  
Natural Gas ◽  
San Diego ◽  
Laminar Flame ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Validation Data ◽  
Data Set ◽  
Reduced Mechanism ◽  
Kinetic Mechanisms

Existing kinetic mechanisms for natural gas combustion are not validated under supercritical oxy-fuel conditions because of the lack of experimental validation data. Our studies show that different mechanisms have different predictions under supercritical oxy-fuel conditions. Therefore, preliminary designers may experience difficulties when selecting a mechanism for a numerical model. This paper evaluates the performance of existing chemical kinetic mechanisms and produces a reduced mechanism for preliminary designers based on the results of the evaluation. Specifically, the mechanisms considered were GRI-Mech 3.0, USC-II, San Diego 204-10-04, NUIG-I, and NUIG-III. The set of mechanisms was modeled in Cantera and compared against the literature data closest to the application range. The high pressure data set included autoignition delay time in nitrogen and argon diluents up to 85 atm and laminar flame speed in helium diluent up to 60 atm. The high carbon dioxide data set included laminar flame speed with 70% carbon dioxide diluent and the carbon monoxide species profile in an isothermal reactor with up to 95% carbon dioxide diluent. All mechanisms performed adequately against at least one dataset. Among the evaluated mechanisms, USC-II has the best overall performance and is preferred over the other mechanisms for use in the preliminary design of supercritical oxy-combustors. This is a significant distinction; USC-II predicts slower kinetics than GRI-Mech 3.0 and San Diego 2014 at the combustor conditions expected in a recompression cycle. Finally, the global pathway selection method was used to reduce the USC-II model from 111 species, 784 reactions to a 27 species, 150 reactions mechanism. Performance of the reduced mechanism was verified against USC-II over the range relevant for high inlet temperature supercritical oxy-combustion.

Optical and Numerical Investigations of Flame Propagation in a Heavy Duty Spark Ignited Natural Gas Engine

2021 ◽  
Author(s):  
Jinlong Liu ◽  
Christopher Ulishney ◽  
Cosmin E. Dumitrescu
Keyword(s):  
Natural Gas ◽  
Flame Propagation ◽  
Turbulence Intensity ◽  
Laminar Flame ◽  
Combustion Process ◽  
Combustion Efficiency ◽  
Flame Speed ◽  
Laminar Flame Speed ◽  
Heavy Duty ◽  
Piston Chamber

Abstract Increasing the natural gas (NG) use in heavy-duty engines is beneficial for reducing greenhouse-gas emissions from power generation and transportation. However, converting compression ignition (CI) engines to NG spark ignition operation can increase methane emissions without expensive aftertreatment, thereby defeating the purpose of utilizing a low carbon fuel. The widely accepted explanation for the low combustion efficiency in such retrofitted engines is the lower laminar flame speed of natural gas. In addition, diesel engine’s larger bowl size compared to the traditional gasoline engines increases the flame travel length inside the chamber and extends the combustion duration. However, optical measurements performed in this study suggested that a fast-propagating flame was developed inside the cylinder even at extremely lean operation. This was supported by a three-dimensional numerical simulation, which indicated that the squish region of the bowl-in-piston chamber generated a high turbulence intensity inside the bowl. However, the flame propagation experienced a sudden 2.25x reduction in speed when transiting from the bowl to the squish region. Such a phenomenon was caused by the large decrease in the turbulence intensity inside the squish region during the combustion process. Moreover, the squish volume trapped an important fuel fraction, and it is this fraction that experienced a slow and inefficient burning process during the expansion stroke. This resulted in increased methane emissions and reduced combustion efficiency. Overall, it was the specifics of the combustion process inside a bowl-in-piston chamber not the methane’s slow laminar flame speed that contributed to the low methane combustion efficiency for the retrofitted engine. The results suggest that optimizing the chamber shape is paramount to boost engine efficiency and decrease its emissions.

Numerical Study on the Effect of Real Syngas Compositions on Ignition Delay Times and Laminar Flame Speeds at Gas Turbine Conditions

2013 ◽  
Author(s):  
Olivier Mathieu ◽  
Eric L. Petersen ◽  
Alexander Heufer ◽  
Nicola Donohoe ◽  
Wayne Metcalfe ◽  
...  
Keyword(s):  
Ignition Delay ◽  
Delay Time ◽  
Gas Turbines ◽  
Ignition Delay Time ◽  
Laminar Flame ◽  
Numerical Study ◽  
Fuel Mixture ◽  
Flame Speed ◽  
Operating Conditions ◽  
Combustion Properties

Depending on the feedstock and the production method, the composition of syngas can include (in addition to H2 and CO) small hydrocarbons, diluents (CO2, water, and N2), and impurities (H2S, NH3, NOx, etc.). Despite this fact, most of the studies on syngas combustion do not include hydrocarbons or impurities and in some cases not even diluents in the fuel mixture composition. Hence, studies with realistic syngas composition are necessary to help designing gas turbines. The aim of this work was to investigate numerically the effect of the variation in the syngas composition on some fundamental combustion properties of premixed systems such as laminar flame speed and ignition delay time at realistic engine operating conditions. Several pressures, temperatures, and equivalence ratios were investigated. To perform this parametric study, a state-of-the-art C0-C5 detailed kinetics mechanism was used. Results of this study showed that the addition of hydrocarbons generally reduces the reactivity of the mixture (longer ignition delay time, slower flame speed) due to chemical kinetic effects. The amplitude of this effect is however dependent on the nature and concentration of the hydrocarbon as well as the initial condition (pressure, temperature, and equivalence ratio).

Laminar Flame Speed Experiments of Alternative Liquid Fuels

2019 ◽  
Author(s):  
Charles L. Keesee ◽  
Bing Guo ◽  
Eric L. Petersen
Keyword(s):  
Equivalence Ratio ◽  
Laminar Flame ◽  
Initial Conditions ◽  
Synthetic Jet ◽  
Flame Speed ◽  
Liquid Fuels ◽  
Jet Fuels ◽  
Data Sets ◽  
Laminar Flame Speed ◽  
Best Parameter

Abstract New laminar flame speed experiments have been collected for multiple alternative liquid fuels. Understanding the combustion characteristics of these synthetic fuels is an important step in developing new chemical kinetics mechanisms that can be applied to real fuels. Included in this study are two synthetic Jet fuels: Syntroleum S-8 and Shell GTL. The precise composition of these fuels is known to change from sample to sample. Since these are low vapor pressure fuels, there are additional uncertainties in their introduction into gas-phase mixtures, leading to uncertainty in the mixture equivalence ratio. An in-situ laser absorption technique was implemented to verify the procedure for filling the vessel and to minimize and quantify the uncertainty in the experimental equivalence ratio. The diagnostic utilized a 3.39-μm HeNe laser in conjunction with Beer’s Law. The resulting spherically expanding flame experiments were conducted over a range of equivalence ratios from φ = 0.7 to φ = 1.5 at initial conditions of 1 atm and 403 K in the high-temperature, high-pressure constant-volume vessel at Texas A&M University. The experimental results show that both fuels have similar flame speeds with a peak value just under 60 cm/s. However, it is shown that when comparing the results from different data sets for these real fuels, equivalence ratio is not necessarily the best parameter to use. Fuel mole fraction may be a better parameter to use as it is independent of the average fuel molecule or fuel surrogate used to calculate equivalence ratio in these real fuel/air mixtures.

Sign in / Sign up

Export Citation Format

Share Document