An Environment Friendly Approach to Reduce the Breakdown Pressure of High Strength Unconventional Rocks by Cyclic Hydraulic Fracturing

2019 ◽  
Vol 142 (4) ◽  
Author(s):  
Zeeshan Tariq ◽  
Mohamed Mahmoud ◽  
Abdulazeez Abdulraheem ◽  
Dhafer Al-Shehri ◽  
Mobeen Murtaza
Keyword(s):  
Hydraulic Fracturing ◽  
High Strength ◽  
Progressive Increase ◽  
New Method ◽  
Hydraulic Fractures ◽  
Breakdown Pressure ◽  
Environment Friendly ◽  
Rock Types ◽  
Pressurization Rate ◽  
Tight Rocks

Abstract Unconventional hydrocarbon resources mostly found in highly stressed, overpressured, and deep formations, where the rock strength and integrity are very high. When fracturing these kinds of rocks, the hydraulic fracturing operation becomes much more challenging and difficult and in some cases reaches to the maximum pumping capacity limits without generating any fracture. This reduces the operational gap to optimally place the hydraulic fractures. Current stimulation methods to reduce the fracture pressures involvement with adverse environmental effects and high costs due to the entailment of water mixed with huge volumes of chemicals. In this study, a new environment friendly approach to reduce the breakdown pressure of the unconventional rock is presented. The new method incorporates the injection of chemical-free fracturing fluid in a series of cycles with a progressive increase of the pressurization rate in each cycle. This study is carried out on different cement blocks with varying petrophysical and mechanical properties to simulate real rock types. The results showed that the new method of cyclic fracturing can reduce the breakdown pressure to 24.6% in ultra-tight rocks, 19% in tight rocks, and 14.8% in medium- to low-permeability rocks. This reduction in breakdown pressure helped to overcome the operational challenges in the field and makes the fracturing operation much greener.

The effect of stress on the primary permeability of rock cores—a facet of hydraulic fracturing

1981 ◽  
Vol 18 (2) ◽  
pp. 195-204 ◽  
Author(s):  
R. Heystee ◽  
J.-C. Roegiers
Keyword(s):  
Rock Mass ◽  
Hydraulic Fracturing ◽  
The State ◽  
Stress Conditions ◽  
Breakdown Pressure ◽  
Rock Types ◽  
State Of Stress ◽  
Pressurization Rate ◽  
Fluid Penetration ◽  
Fracturing Experiments

Recent laboratory hydraulic fracturing experiments have shown that fluid penetration into the rock mass adjacent to the borehole being pressurized has a significant influence on the magnitude of the breakdown pressure. One factor affecting the degree of penetration of the pressurizing fluid is the permeability of the rock mass, which in turn is a function of the state of stress present in the rock mass. To study this permeability–stress relationship, a radial permeameter was constructed and three rock types tested. Derived expressions show that during radially divergent and convergent flow in the permeameter, the state of stress in the rock specimen is tensile and compressive respectively. The radial permeameter test results show that the permeability of rock increases significantly under tensile stress conditions and reduces under compressive stress conditions. The results from this study were used to develop a conceptual model which explains the dependency of breakdown pressure levels on the pressurization rate.

scholarly journals An Experimental Study to Reduce the Fracture Pressure of High Strength Rocks Using a Novel Thermochemical Fracturing Approach

Geofluids ◽  
2019 ◽  
Vol 2019 ◽  
pp. 1-16 ◽  
Author(s):  
Zeeshan Tariq ◽  
Mohamed A. Mahmoud ◽  
A. Abdulraheem ◽  
Ayman Al-Nakhli ◽  
Mohammed BaTaweel
Keyword(s):  
Pressure Rise ◽  
High Strength ◽  
Hydrocarbon Reservoirs ◽  
Hydraulic Fractures ◽  
Breakdown Pressure ◽  
Fracture Pressure ◽  
Breakdown Time ◽  
Operational Window ◽  
Fracturing Experiments ◽  
Engineering Practices

Current oil prices and global financial situations underline the need for the best engineering practices to recover remaining oil from unconventional hydrocarbon reservoirs. These hydrocarbon reservoirs are mostly situated in deep and overpressured formations, with high rock strength and integrity. Breakdown pressure of the rock is a function of their tensile strength and in situ stresses acting on them. Fracturing stimulation techniques become challenging when treating these types of rocks, and many cases approached to the operational limits. This leaves a small operational window to initiate and place hydraulic fractures. In this study, a new methodology to reduce the breakdown pressure of the high stressed rock is presented. The new method enables the fracturing of high stressed rocks more economically and efficiently. Fracturing experiments were carried out on different blocks, and the breakdown pressure was measured by creating a simulated borehole at the center of the block. Thermochemical fluids were injected to create the microfractures. These microfractures improved the permeability and porosity and reduced the elastic strength of the subjected samples prior to the main hydraulic fracturing job. The posttreatment experimental analysis confirmed the presence of microfractures which were originated due to the pressure pulse generated from the thermochemical reaction. The results of this study showed that the newly formulated method of thermochemical fracturing reduced the breakdown pressure by 38% in slim borehole blocks and 60% in large borehole blocks. Results also showed that the breakdown time to initiate the fractures was reduced to 19% in slim borehole blocks and 17% in large borehole blocks. The reduction in breakdown pressure and breakdown time happened due to the creation of microfractures by the pressure rise phenomenon in a new thermochemical fracturing approach.

Geologic Controls on Gas Production and Hydraulic-Fracturing Flowback in Tight Gas Sandstones of the Late Jurassic Monteith Formation, Deep Basin, Alberta, Canada

2016 ◽  
Vol 19 (01) ◽  
pp. 024-040 ◽  
Author(s):  
Liliana Zambrano ◽  
Per K. Pedersen ◽  
Roberto Aguilera
Keyword(s):  
Hydraulic Fracturing ◽  
Gas Production ◽  
Production Performance ◽  
Rock Properties ◽  
Hydraulic Fractures ◽  
Tight Gas ◽  
Deep Basin ◽  
Rock Types ◽  
Sandstone Reservoirs ◽  
Geologic Controls

Summary A comparison of rock properties integrated with production performance and hydraulic-fracturing flowback (FB) of the uppermost lithostratigraphic “Monteith A” and the lowermost portion “Monteith C” of the Monteith Formation in the Western Canada Sedimentary Basin (WCSB) in Alberta is carried out with the use of existing producing gas wells. The analyses are targeted to understand the major geologic controls that differentiate the two tight gas sandstone reservoirs. This study consists of basic analytical tools available for geological characterization of tight gas reservoirs that is based on the identification and comparison of different rock types such as depositional, petrographic, and hydraulic for each lithostratigraphic unit of the Monteith Formation. As these low-matrix-permeability sandstone reservoirs were subjected to intense post-depositional diagenesis, a comparison of the various rock types allows the generation of more-accurate reservoir description, and a better understanding of the key geologic characteristics that control gas-production potential and possible impact on hydraulic-fracturing FB. Well performance and FB were the focus of many previous simulation and geochemical studies. In contrast, we find that an adequate understanding of the rocks hosting hydraulic fractures is a necessary complement to those studies for estimating FB times. This understanding was lacking in some previous studies. As a result, a new method is proposed on the basis of a crossplot of cumulative gas production vs. square root of time for estimating FB time. It is concluded that the “Monteith A” unit has better rock quality than the “Monteith C” unit because of less-heterogeneous reservoir geometry, less-complex mineralogical composition, and larger pore-throat apertures.

scholarly journals Effect of Joint Geometrical Parameters on Hydraulic Fracture Network Propagation in Naturally Jointed Shale Reservoirs

Geofluids ◽  
2018 ◽  
Vol 2018 ◽  
pp. 1-23 ◽  
Author(s):  
Zhaohui Chong ◽  
Qiangling Yao ◽  
Xuehua Li
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Fracture Network ◽  
Hydraulic Fractures ◽  
Geometrical Parameters ◽  
Breakdown Pressure ◽  
Opening Mode ◽  
Hydraulic Fracture Network ◽  
Shale Reservoirs ◽  
Network Pattern

The presence of a significant amount of discontinuous joints results in the inhomogeneous nature of the shale reservoirs. The geometrical parameters of these joints exert effects on the propagation of a hydraulic fracture network in the hydraulic fracturing process. Therefore, mechanisms of fluid injection-induced fracture initiation and propagation in jointed reservoirs should be well understood to unleash the full potential of hydraulic fracturing. In this paper, a coupled hydromechanical model based on the discrete element method is developed to explore the effect of the geometrical parameters of the joints on the breakdown pressure, the number and proportion of hydraulic fractures, and the hydraulic fracture network pattern generated in shale reservoirs. The microparameters of the matrix and joint used in the shale reservoir model are calibrated through the physical experiment. The hydraulic parameters used in the model are validated through comparing the breakdown pressure derived from numerical modeling against that calculated from the theoretical equation. Sensitivity analysis is performed on the geometrical parameters of the joints. Results demonstrate that the HFN pattern resulting from hydraulic fracturing can be roughly divided into four types, i.e., crossing mode, tip-to-tip mode, step path mode, and opening mode. As β (joint orientation with respect to horizontal principal stress in plane) increases from 0° to 15° or 30°, the hydraulic fracture network pattern changes from tip-to-tip mode to crossing mode, followed by a gradual decrease in the breakdown pressure and the number of cracks. In this case, the hydraulic fracture network pattern is controlled by both γ (joint step angle) and β. When β is 45° or 60°, the crossing mode gains dominance, and the breakdown pressure and the number of cracks reach the lowest level. In this case, the HFN pattern is essentially dependent on β and d (joint spacing). As β reaches 75° or 90°, the step path mode is ubiquitous in all shale reservoirs, and the breakdown pressure and the number of the cracks both increase. In this case, β has a direct effect on the HFN pattern. In shale reservoirs with the same β, either decrease in k (joint persistency) and e (joint aperture) or increase in d leads to the increase in the breakdown pressure and the number of cracks. It is also found that changes in d and e result in the variation in the proportion of different types of hydraulic fractures. The opening mode of the hydraulic fracture network pattern is observed when e increases to 1.2 × 10−2 m.

scholarly journals A multi-perforation staged fracturing experimental study on hydraulic fracture initiation and propagation

2020 ◽  
Vol 38 (6) ◽  
pp. 2466-2484
Author(s):  
Jianguang Wei ◽  
Saipeng Huang ◽  
Guangwei Hao ◽  
Jiangtao Li ◽  
Xiaofeng Zhou ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fracture ◽  
Oil And Gas ◽  
Fracture Initiation ◽  
Fracture Network ◽  
Hydraulic Fractures ◽  
Breakdown Pressure ◽  
Tight Sandstone ◽  
Heterogeneous Samples ◽  
Initiation And Propagation

Hydraulic fracture initiation and propagation are extremely important on deciding the production capacity and are crucial for oil and gas exploration and development. Based on a self-designed system, multi-perforation cluster-staged fracturing in thick tight sandstone reservoir was simulated in the laboratory. Moreover, the technology of staged fracturing during casing completion was achieved by using a preformed perforated wellbore. Three hydraulic fracturing methods, including single-perforation cluster fracturing, multi-perforation cluster conventional fracturing and multi-perforation cluster staged fracturing, were applied and studied, respectively. The results clearly indicate that the hydraulic fractures resulting from single-perforation cluster fracturing are relatively simple, which is difficult to form fracture network. In contrast, multi-perforation cluster-staged fracturing has more probability to produce complex fractures including major fracture and its branched fractures, especially in heterogeneous samples. Furthermore, the propagation direction of hydraulic fractures tends to change in heterogeneous samples, which is more likely to form a multi-directional hydraulic fracture network. The fracture area is greatly increased when the perforation cluster density increases in multi-perforation cluster conventional fracturing and multi-perforation cluster-staged fracturing. Moreover, higher perforation cluster densities and larger stage numbers are beneficial to hydraulic fracture initiation. The breakdown pressure in homogeneous samples is much higher than that in heterogeneous samples during hydraulic fracturing. In addition, the time of first fracture initiation has the trend that the shorter the initiation time is, the higher the breakdown pressure is. The results of this study provide meaningful suggestions for enhancing the production mechanism of multi-perforation cluster staged fracturing.

Chemically-Induced Pressure Pulse: Fracturing Competent Reservoirs

2021 ◽  
Author(s):  
Ayman R. Al-Nakhli ◽  
Zeeshan Tariq ◽  
Mohamed Mahmoud ◽  
Abdulazeez Abdulraheem
Keyword(s):  
Hydraulic Fracturing ◽  
Rock Fracture ◽  
Applied Pressure ◽  
Hydraulic Fractures ◽  
Breakdown Pressure ◽  
Hydrocarbon Production ◽  
Fracture Pressure ◽  
Micro Cracks ◽  
Chemically Induced ◽  
Fracturing Experiments

Abstract Commercial volumes of hydrocarbon production from tight unconventional reservoirs need massive hydraulic fracturing operations. Tight unconventional formations are typically located inside deep and over-pressured formations where the rock fracture pressure with slickwater becomes so high because of huge in situ stresses. Therefore, several lost potentials and failures were recorded because of high pumping pressure requirements and reservoir tightness. In this study, thermochemical fluids are introduced as a replacement for slickwater. These thermochemical fluids are capable of reducing the rock fracture pressure by generating micro-cracks and tiny fractures along with the main hydraulic fractures. Thermochemical upon reaction can generate heat and pressure simultaneously. In this study, several hydraulic fracturing experiments in the laboratory on different synthetic cement samples blocks were carried out. Cement blocks were made up of several combinations of cement and sand ratios to simulate real rock scenarios. Results showed that fracturing with thermochemical fluids can reduce the breakdown pressure of the cement blocks by 30%, while applied pressure was reduced up to 88%, when using thermochemical fluid, compared to slickwater. In basins with excessive tectonic stresses, the current invention can become an enabler to fracture and stimulate well stages which otherwise left untreated. A new methodology is developed to lower the breakdown pressure of such reservoirs, and enable fracturing. Keywords: Unconventional formation; breakdown pressure; thermochemicals; micro fractures.

scholarly journals Experimental Study on the Initiation and Propagation of Multi-Cluster Hydraulic Fractures within One Stage in Horizontal Wells

Energies ◽  
2021 ◽  
Vol 14 (17) ◽  
pp. 5357
Author(s):  
Zhenhui Bi ◽  
Lei Wang ◽  
Hanzhi Yang ◽  
Yintong Guo ◽  
Xin Chang ◽  
...  
Keyword(s):  
Hydraulic Fracturing ◽  
Hydraulic Fractures ◽  
Breakdown Pressure ◽  
Multiple Fractures ◽  
Previous Fracture ◽  
One Stage ◽  
Initiation And Propagation ◽  
Pump Rate ◽  
Subsequent Fracture ◽  
Fracture Multiple

Competitive propagation of fractures initiated from multiple perforation clusters is universal in hydraulic fracturing of unconventional reservoirs, which largely influences stimulation. However, the propagation mechanism of multi-fractures has not been fully revealed for the lack of a targeted laboratory observation. In this study, a physical simulation experiment system was developed for investigating the initiation and propagation of multi-cluster hydraulic fractures. Different from the traditional hydro-fracking test system, the new one was equipped with a multi-channel shunting module and a strain monitoring system, which could guarantee the full fracture extension at each perforation clusters and measure the internal deformation of specimens, respectively. Several groups of true tri-axial fracturing tests were performed, considering the factors of in situ stress, cluster spacing, pumping rate, and bedding structures. The results showed that initiation of multi-cluster hydraulic fractures within one stage could be simultaneous or successive according to the difference of the breakdown pressure and fracturing fluid injection. For simultaneous initiation, the breakdown pressure of the subsequent fracture was lower than or equal to the value of the previous fracture. Multiple fractures tended to attract and merge. For successive initiation, the breakdown pressures of fractures were gradually increasing. The subsequent fracture tended to intersect with or deviated from the previous fracture. Multiple fractures interaction was aggravated by the decrease of horizontal stress difference, bedding number and cluster spacing, and weakened by the increase of pump rate. The propagation area of multiple fractures increased with the pump rate, decreased with the cluster spacing. The strain response characteristics corresponded with the initiation and propagation of fracture, which was conducive to understanding the process of the fracturing. The test results provide a basis for optimum design of hydraulic fracturing.

Sign in / Sign up

Export Citation Format

Share Document