Heat Transfer and Friction Factor Correlations for Solar Air Heater With Gap in V-Rib With Symmetrical Gap and Staggered Ribs

2019 ◽  
Vol 12 (3) ◽  
Author(s):  
Sumer Singh Patel ◽  
Atul Lanjewar
Keyword(s):  
Heat Transfer ◽  
Friction Factor ◽  
Smooth Surface ◽  
Heat Transfer Analysis ◽  
Operating Parameters ◽  
Solar Air Heater ◽  
Gap Size ◽  
Maximum Enhancement ◽  
Air Heater ◽  
Relative Roughness

Abstract The present experimental study is concerned with heat transfer analysis of air flowing in solar air heater duct with a gap in V-rib with symmetrical gap and staggered ribs geometry. The investigated parameters are Reynolds number (Re) of 4000–14,000, relative roughness pitch (p/e) of 12, relative roughness height (e/Dh) of 0.043, angle of attack (α) of 60 deg, relative staggered rib pitch (p′/p) of 0.65, relative gap size (g/e) of 4, relative staggered rib size (r/e) of 4, relative gap position of additional gap in each symmetrical rib elements (d/w) of 0.65, relative gap size of additional gap in each symmetrical rib elements (g′/e) of 1, number of main gaps (Ng) of 1, 2, 3, 4, and number of additional gap (ng) varying from 1 to 5. Fourteen roughened absorber plates were tested. The maximum enhancement in Nusselt number (Nu) and friction factor (f) was 2.34 and 2.79 times that of smooth surface corresponding to the number of main gaps (Ng) of 4 with the number of additional gaps (ng) of 4. The performance of the gap in V-rib with symmetrical gap and staggered rib geometry has been compared with the existing latest V-rib geometry and smooth surface. The proposed gap in V-rib with symmetrical gap and staggered ribs geometry has a better performance than the existing latest V-rib geometry. The following correlations have been developed for heat transfer and friction factor in terms of roughness and operating parameters. Heat transfer:Nur=0.0073(Re)0.9788(Ng)0.2790(ng)0.0184exp[−0.1678(ln(Ng))2]exp[−0.0129(ln(ng))2] Friction factor:fr=0.0477(Re)−0.0678(Ng)0.5919(ng)−0.0562exp[−0.4922(ln(Ng))2]exp[−0.0487(ln(ng))2]

Thermal–hydraulic analysis of a solar air heater fitted with a wire-roughened absorber plate

2021 ◽  
pp. 095440892110590
Author(s):  
Nanjundappa Madhukeshwara ◽  
A Alhadhrami ◽  
Hassan A H Alzahrani ◽  
B H Prasanna
Keyword(s):  
Heat Transfer ◽  
Friction Factor ◽  
Efficiency Index ◽  
Hydraulic Performance ◽  
Index Formula ◽  
Solar Air Heater ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness ◽  
Nusselt Numbers

This study is to evaluate heat transmission and friction in a rectangular solar air heater with a V-shaped wire rib roughness on the absorber plate that operates in fully formed turbulent flow. Additionally, studies are performed to generate prediction equations for the average friction factor, Stanton number, and efficiency index. The Reynolds number [Formula: see text]–[Formula: see text], angle of attack [Formula: see text]20[Formula: see text]–90[Formula: see text]), relative roughness pitch [Formula: see text]–[Formula: see text], relative roughness height [Formula: see text]–[Formula: see text], and the aspect ratio [Formula: see text]–[Formula: see text] was varied. The efficiency index [Formula: see text] is commonly employed as a thermo-hydraulic performance metric. It is computed as [Formula: see text]. The wire roughness and airflow parameters [Formula: see text] are optimized to maximize heat transfer while retaining minimal friction losses. On the basis of resemblance criteria, average Stanton numbers, average Nusselt numbers, and even average friction factors are derived. The results are compared to those obtained with a smooth absorber duct under similar airflow circumstances in order to assess the increase in heat transfer coefficient and friction factor. The [Formula: see text], and [Formula: see text] have a significant influence on thermo–hydraulic performance, according to these studies. With [Formula: see text], [Formula: see text], [Formula: see text], and [Formula: see text], the optimal configuration geometry for wire roughness and solar air heater duct is identified.

scholarly journals CFD Analysis to Study Effect of Circular Vortex Generator Placed in Inlet Section to Investigate Heat Transfer Aspects of Solar Air Heater

2014 ◽  
Vol 2014 ◽  
pp. 1-11 ◽  
Author(s):  
Vipin B. Gawande ◽  
A. S. Dhoble ◽  
D. B. Zodpe
Keyword(s):  
Heat Transfer ◽  
Nusselt Number ◽  
Friction Factor ◽  
Vortex Generator ◽  
Inlet Section ◽  
Solar Air Heater ◽  
Cfd Analysis ◽  
Absorber Plate ◽  
Air Heater ◽  
Relative Roughness

CFD analysis of 2-dimensional artificially roughened solar air heater duct with additional circular vortex generator, inserted in inlet section is carried out. Circular transverse ribs on the absorber plate are placed as usual. The analysis is done to investigate the effect of inserting additional vortex generator on the heat transfer and flow friction characteristics inside the solar air heater duct. This investigation covers relative roughness pitch in the range of 10 ≤P/e≤ 25 and relevant Reynolds numbers in the range of 3800 ≤ Re ≤ 18000. Relative roughness height (e/D) is kept constant as 0.03 for analysis. The turbulence created due to additional circular vortex generator increases the heat transfer rate and at the same time there is also increase in friction factor values. For combined arrangement of ribs and vortex generator, maximum Nusselt number is found to be 2.05 times that of the smooth duct. The enhancement in Nusselt number with ribs and additional vortex generator is found to be 1.06 times that of duct using ribs alone. The maximum increase in friction factor with ribs and circular vortex generator is found to be 2.91 times that of the smooth duct. Friction factor in a combined arrangement is 1.114 times that in a duct with ribs alone on the absorber plate. The augmentation in Thermal Enhancement Factor (TEF) with vortex generator in inlet section is found to be 1.06 times more than with circular ribs alone on the absorber plate.

Experimental Investigation of Thermohydraulic Performance of the Solar Air Heater Having Arc-Shaped Ribs With Multiple Gaps

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Sheetal Kumar Jain ◽  
Ghanshyam Das Agrawal ◽  
Rohit Misra
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Nusselt Number ◽  
Friction Factor ◽  
Solar Air Heater ◽  
Artificial Roughness ◽  
Absorber Plate ◽  
Maximum Enhancement ◽  
Air Heater ◽  
Absorber Surface

Abstract In the present research, the thermohydraulic performance of a solar air heater having artificial roughness in the form of arc-shaped ribs with multiple gaps has been investigated experimentally and compared with that of a solar air heater having smooth absorber plate. The performance has been investigated in terms of enhancement in the Nusselt number and friction factor. Results of the present work have also been compared with previously published work. Reynolds number and arc angle (α) were varied from 3000 to 18,000 and 30 deg to 75 deg, respectively. Present roughness results in a higher rate of heat transfer from the absorber surface to air, but it also imposes a penalty in terms of the increased friction factor. Maximum enhancement in Nusselt number, friction factor, and thermohydraulic performance parameter for the roughened absorber surface is found to be 3.74, 2.69, and 2.75 times that of the smooth plate, respectively. Correlations of heat transfer and friction factor for proposed roughness have also been developed.

Experimental Investigation of Heat Transfer and Friction Characteristics of Arc-Shaped Roughness Elements Having Central Gaps on the Absorber Plate of Solar Air Heater

2016 ◽  
Vol 138 (4) ◽  
Author(s):  
Navneet Kumar Pandey ◽  
Vijay Kumar Bajpai
Keyword(s):  
Heat Transfer ◽  
Experimental Investigation ◽  
Reynolds Number ◽  
Friction Factor ◽  
Angle Of Attack ◽  
Solar Air Heater ◽  
Maximum Enhancement ◽  
Friction Characteristics ◽  
Air Heater ◽  
Circular Arcs

Thermal performance of solar air heater does not take into account the energy loss due to friction for propelling air through the duct. In this work, an experimental investigation has been carried out to study the effect of heat transfer and friction characteristics of turbulent flow of air passing through rectangular duct which is roughened by circular arcs having gaps of 2 mm in between arranged in angular fashion, and the roughened wall is uniformly heated. The thermal and friction characteristics are governed by duct aspect ratio (W/H), hydraulic diameter (D), and relative roughness pitch (P/e), angle of attack of angular arc (α), and Reynolds number (Re). Experiments encompassed the Reynolds number ranges from 3600 to 15,100, P/e ranges from 6 to 20, and angle of attack of angular arc of flow over the protrusions ranges from 15 deg to 75 deg. The results have also been compared to W-shaped roughness inclined at 45 deg. The maximum enhancement in heat transfer and friction factor is 3.15 and 3.93 times as compared with smooth duct. Arc with gaps have also been observed to be better than their W-shaped counterparts. These experimental results have been used to study their influence on Nusselt number and friction factor, and empirical relations have been derived using regression analysis.

Sign in / Sign up

Export Citation Format

Share Document