Computational Fluid Dynamic Analyses of Flow and Combustion in a Domestic Liquified Petroleum Gas Cookstove Burner—Part I: Design Optimization of Mixing Tube–Burner Assembly

2019 ◽  
Vol 12 (3) ◽  
Author(s):  
Sourav Dey ◽  
Mithun Das ◽  
Ranjan Ganguly ◽  
Amitava Datta ◽  
Meenam M. Verma ◽  
...  
Keyword(s):  
High Efficiency ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Heat Content ◽  
Ambient Air ◽  
High Heat ◽  
Liquefied Petroleum Gas ◽  
Nozzle Position ◽  
Air Ingress ◽  
Tube Assembly

Abstract Liquefied petroleum gas (LPG) is commonly used in domestic kitchen due to its low health and environmental impacts and high heat content compared to other traditional fuels. The growing demand of LPG, notwithstanding its limited reserve, influences the need for performance improvement of the LPG cookstoves. In an LPG cookstove, the fuel–air mixture is prepared in a self-aspirated burner, and burns as a rich premixed flame above the burner. The fuel–air ratio of the reactant mixture influences the burning characteristics and thermal efficiency of the cookstove. This part of work deals with a numerical study of flow and mixing characteristics in the mixing tube and burner assembly of a domestic LPG cookstove. The fuel is injected axially through a narrow nozzle inside the mixing tube causing entrainment of ambient air through the side ports and the end port. The effects of different side-port geometry, nozzle position, inlet fuel pressure, and nozzle throat diameter on the air ingress have been systematically investigated, and the optimum design has been identified. Results of the study provide important information on the design of the practical nozzle and mixing tube assembly of high-efficiency LPG stoves.

Numerical study of fluid dynamic flow within an internal combustion engine cylinder

2017 ◽  
Author(s):  
Ana Marta Souza ◽  
Antônio César Valadares de Oliveira ◽  
Enrico Temporim Ribeiro ◽  
Francisco Souza ◽  
Marcelo Colombo Chiari
Keyword(s):  
Internal Combustion Engine ◽  
Combustion Engine ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Internal Combustion ◽  
Dynamic Flow ◽  
Engine Cylinder

scholarly journals Experimental Investigation and Comparison of the Thermal Performance of Additively and Conventionally Manufactured Heat Exchangers

Metals ◽  
2021 ◽  
Vol 11 (4) ◽  
pp. 574
Author(s):  
Ana Vafadar ◽  
Ferdinando Guzzomi ◽  
Kevin Hayward
Keyword(s):  
Surface Roughness ◽  
Thermal Performance ◽  
Heat Exchangers ◽  
High Efficiency ◽  
Cooling System ◽  
Fluid Dynamic ◽  
Dynamic Performance ◽  
Experimental Studies ◽  
Manufacturing Method ◽  
Industrial Sectors

Air heat exchangers (HXs) are applicable in many industrial sectors because they offer a simple, reliable, and cost-effective cooling system. Additive manufacturing (AM) systems have significant potential in the construction of high-efficiency, lightweight HXs; however, HXs still mainly rely on conventional manufacturing (CM) systems such as milling, and brazing. This is due to the fact that little is known regarding the effects of AM on the performance of AM fabricated HXs. In this research, three air HXs comprising of a single fin fabricated from stainless steel 316 L using AM and CM methods—i.e., the HXs were fabricated by both direct metal printing and milling. To evaluate the fabricated HXs, microstructure images of the HXs were investigated, and the surface roughness of the samples was measured. Furthermore, an experimental test rig was designed and manufactured to conduct the experimental studies, and the thermal performance was investigated using four characteristics: heat transfer coefficient, Nusselt number, thermal fluid dynamic performance, and friction factor. The results showed that the manufacturing method has a considerable effect on the HX thermal performance. Furthermore, the surface roughness and distribution, and quantity of internal voids, which might be created during and after the printing process, affect the performance of HXs.

Un-Shocked High Amplitude Standing Waves in Wave-Shaped Resonators

2012 ◽  
Author(s):  
Dion Savio Antao ◽  
Bakhtier Farouk
Keyword(s):  
Numerical Study ◽  
Fluid Dynamic ◽  
Ambient Pressure ◽  
Standing Waves ◽  
High Amplitude ◽  
Prime Mover ◽  
Non Linear ◽  
Resonator System ◽  
Cylindrical Resonators ◽  
Linear Nature

A numerical study of non-linear, high amplitude standing waves in non-cylindrical circular resonators is reported here. These waves are shock-less and can generate peak acoustic overpressures that can exceed the ambient pressure by three/four times its nominal value. A high fidelity compressible computational fluid dynamic model is used to simulate the phenomena in cylindrical and arbitrarily shaped axisymmetric resonators. A right circular cylinder and frustum of cone are the two geometries studied. The model is validated using past numerical and experimental results of standing waves in cylindrical resonators. The non-linear nature of the harmonic response of the frustum of cone resonator system is investigated for two different working fluids (carbon dioxide and argon) operating at various values of piston amplitude. The high amplitude non-linear oscillations demonstrated can be used as a prime mover in a variety of applications including thermoacoustic cryocooling.

An Integral Heat Sink for Cooling Microelectronic Components

1993 ◽  
Vol 115 (3) ◽  
pp. 284-291 ◽  
Author(s):  
S. H. Bhavnani ◽  
C.-P. Tsai ◽  
R. C. Jaeger ◽  
D. L. Eison
Keyword(s):  
Heat Sink ◽  
Silicon Surface ◽  
Numerical Study ◽  
High Heat ◽  
Heat Fluxes ◽  
Silicon Surfaces ◽  
Source Surface ◽  
Mouth Size ◽  
Severe Constraint ◽  
Boiling Incipience

Liquid immersion cooling is rapidly becoming the mechanism of choice for the newest generation of supercomputers. Miniaturization at both the chip and module level places a severe constraint on the size of the heat sink employed to dissipate the high heat fluxes generated. A study was conducted to develop a surface that could augment boiling heat transfer from silicon surfaces under these constraints. The surface created consists of reversed pyramidal features etched directly on to the silicon surface. Experiments were conducted in a saturated pool of refrigerant-113 at atmospheric pressure. The inexpensive crystallographic etching techniques used to create the enhanced features are described in the paper. The main characteristics of interest in the present study were the incipient boiling superheat and the magnitude of the temperature overshoot at boiling incipience. Results were obtained for test sections with various cavity densities, and compared with data for the smooth untreated surface. It was found that incipient boiling superheat was reduced from a range of 27.0–53.0° C for the untreated silicon surface, to a range of 2.5–15.0° C for the enhanced surfaces. The overshoot also decreased considerably; from about 12.0–18.0° C for two classes of untreated surfaces, to a range of 1.5–5.3° C for the enhanced surfaces. The values of the incipient boiling superheat, and those of the overshoot decreased with a decrease in cavity mouth size. Two ratios of heat source surface area to the area of the enhanced surface were studied. The overshoot values obtained for these surfaces were compared with those observed for some commonly used enhanced surfaces. An elementary numerical study was conducted to estimate the magnitude of heat spreading.

Experimental and Numerical Study of Vortex Induced Vibrations on a Spool Model

2018 ◽  
Author(s):  
David Gross ◽  
Yann Roux ◽  
Benjamin Rousse ◽  
François Pétrié ◽  
Ludovic Assier ◽  
...  
Keyword(s):  
Stokes Equations ◽  
Numerical Study ◽  
Fluid Dynamic ◽  
Navier Stokes ◽  
Navier Stokes Equations ◽  
Flow Perturbation ◽  
Industry Standards ◽  
Vortex Induced Vibrations ◽  
Recommended Practices ◽  
Decay Tests

The problem of Vortex-Induced Vibrations (VIV) on spool and jumper geometries is known to present several drawbacks when approached with conventional engineering tools used in the study of VIV on risers. Current recommended practices can lead to over-conservatism that the industry needs to quantify and minimize within notably cost reduction objectives. Within this purpose, the paper will present a brief critical review of the Industry standards and more particularly focus on both experimental and Computational Fluid Dynamic (CFD) approaches. Both qualitative and quantitative comparisons between basin tests and CFD results for a 2D ‘M-shape’ spool model will be detailed. The results presented here are part of a larger experimental and numerical campaign which considered a number of current velocities, heading and geometry configurations. The vibratory response of the model will be investigated for one of the current velocities and compared with the results obtained through recommended practices (e.g. Shear7 and DNV guidelines). The strategy used by the software K-FSI to solve the fluid-structure interaction (FSI) problem is a partitioned coupling solver between fluid solver (FINE™/Marine) and structural solvers (ARA). FINE™/Marine solves the Reynolds-Averaged Navier-Stokes Equations in a conservative way via the finite volume method and can work on structured or unstructured meshes with arbitrary polyhedrons, while ARA is a nonlinear finite element solver with a large displacement formulation. The experiments were conducted in the BGO FIRST facility located in La Seyne sur Mer, France. Particular attention was paid towards the model design, fabrication, instrumentation and characterization, to ensure an excellent agreement between the structural numerical model and the actual physical model. This included the use of a material with low structural damping, the performance of stiffness and decay tests in air and in still water, plus the rationalization of the instrumentation to be able to capture the response with the minimum flow perturbation or interaction due to instrumentation.

Experimental Investigation on Contact Angle of Sintered Copper Powder Wick

2016 ◽  
Vol 819 ◽  
pp. 575-579 ◽  
Author(s):  
Nandy Putra ◽  
Iwan Setyawan ◽  
Dimas Raditya
Keyword(s):  
Contact Angle ◽  
Copper Powder ◽  
High Speed ◽  
Ambient Air ◽  
Video Camera ◽  
High Heat ◽  
High Heat Flux ◽  
Powder Particle Size ◽  
Air Exposure ◽  
Sintered Copper

Heat pipes are widely used in electronic cooling and other applications that require efficient transport or spreading of heat from local sources of high heat flux. One factor that most affect the performance of this device is the wetting properties of the wick material, whereby a hydrophilic wick material is required to transport the liquid from the evaporator to the condenser. The performance of heat pipe will decrease when the wick surface becomes hydrophobic as indicated by changes in its contact angle (CA). This study aims to determine the effect of ambient air exposure on the wettability of wick material. Wettability for a surface by a certain liquid can be shown by measuring the contact angle of liquid droplets on the surface. In this experiment, the contact angle was captured using a high speed video camera followed by image processing and then measured using Image J software. The surface of the sample/wick is a sintered copper powder which in this study through a process of forming or compaction by various parameters such as powder particle size, compacting pressure and sintering temperature. From the results of this study was found that the longer wicks were exposed in the ambient air, the contact angle of the liquid on the wick surface will be getting increased. After 7 days were contaminated on the ambient air, then all samples have been turned into hydrophobic, CA>90°.

scholarly journals Measurement of Ozone Production Sensor

2010 ◽  
Vol 3 (3) ◽  
pp. 545-555 ◽  
Author(s):  
M. Cazorla ◽  
W. H. Brune
Keyword(s):  
Production Rate ◽  
High Efficiency ◽  
Ambient Air ◽  
Ozone Production ◽  
State University ◽  
Photostationary State ◽  
Sample Chamber ◽  
Efficiency Conversion ◽  
The Difference ◽  
Teflon Film

Abstract. A new ambient air monitor, the Measurement of Ozone Production Sensor (MOPS), measures directly the rate of ozone production in the atmosphere. The sensor consists of two 11.3 L environmental chambers made of UV-transmitting Teflon film, a unit to convert NO2 to O3, and a modified ozone monitor. In the sample chamber, flowing ambient air is exposed to the sunlight so that ozone is produced just as it is in the atmosphere. In the second chamber, called the reference chamber, a UV-blocking film over the Teflon film prevents ozone formation but allows other processes to occur as they do in the sample chamber. The air flows that exit the two chambers are sampled by an ozone monitor operating in differential mode so that the difference between the two ozone signals, divided by the exposure time in the chambers, gives the ozone production rate. High-efficiency conversion of NO2 to O3 prior to detection in the ozone monitor accounts for differences in the NOx photostationary state that can occur in the two chambers. The MOPS measures the ozone production rate, but with the addition of NO to the sampled air flow, the MOPS can be used to study the sensitivity of ozone production to NO. Preliminary studies with the MOPS on the campus of the Pennsylvania State University show the potential of this new technique.

Sign in / Sign up

Export Citation Format

Share Document