Two-Phase Performance of a Hybrid Jet Plus Multipass Microchannel Heat Sink

2019 ◽  
Vol 12 (1) ◽  
Author(s):  
Shailesh N. Joshi ◽  
Danny J. Lohan ◽  
Ercan M. Dede
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Rate ◽  
Heat Sink ◽  
Maximum Pressure ◽  
Microchannel Heat Sink ◽  
Large Area ◽  
Two Phase ◽  
Maximum Heat ◽  
Flow Rates

Abstract The heat transfer and fluid flow performance of a hybrid jet plus multipass microchannel heat sink in two-phase operation is evaluated for the cooling of a single large area, 3.61 cm2, heat source. The two-layer branching microchannel heat sink is evaluated using HFE-7100 as the coolant at three inlet volumetric flow rates of 150, 300, and 450 ml/min. The boiling performance is highest for the flow rate of 450 ml/min with the maximum heat flux value of 174 W/cm2. Critical heat flux (CHF) was observed at two of the tested flow rates, 150 and 300 ml/min, before reaching the maximum operating temperature for the serpentine heater. At 450 ml/min, the heater reached the maximum allowable temperature prior to observing CHF. The maximum pressure drop for the heat sink is 34.1 kPa at a heat flux of 164 W/cm2. Further, the peak heat transfer coefficient value of the heat sink is 28,700 W/m2 K at a heat flux value of 174 W/cm2 and a flow rate of 450 ml/min. Finally, a validated correlation of the single device cooler is presented that predicts heat transfer performance and can be utilized in the design of multidevice coolers.

Numerical and Experimental Investigations on Heat Transfer Phenomena of an Aluminium Microchannel Heat Sink

2011 ◽  
Vol 145 ◽  
pp. 129-133 ◽  
Author(s):  
Thanhtrung Dang ◽  
Ngoctan Tran ◽  
Jyh Tong Teng
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Mass Flow Rate ◽  
Mass Flow ◽  
Flow Rate ◽  
Heat Sink ◽  
Inlet Temperature ◽  
Outlet Temperature ◽  
Microchannel Heat Sink ◽  
Maximum Heat

The study was done both numerically and experimentally on the heat transfer behaviors of a microchannel heat sink. The solver of numerical simulations (CFD - ACE+software package) was developed by using the finite volume method. This numerical method was performed to simulate for an overall microchannel heat sink, including the channels, substrate, manifolds of channels as well as the covered top wall. Numerical results associated with such kinds of overall microchannel heat sinks are rarely seen in the literatures. For cases done in this study, a heat flux of 9.6 W/cm2was achieved for the microchannel heat sink having the inlet temperature of 25 °C and mass flow rate of 0.4 g/s with the uniform surface temperature of bottom wall of the substrate of 50 °C; besides, the maximum heat transfer effectiveness of this device reached 94.4%. Moreover, in this study, when the mass flow rate increases, the outlet temperature decreases; however, as the mass flow rate increases, the heat flux of this heat sink increases also. In addition, the results obtained from the numerical analyses were in good agreement with those obtained from the experiments as well as those from the literatures, with the maximum discrepancies of the heat fluxes estimated to be less than 6 %.

An Experimental Study of Two Phase Flow in Impinging Micro Channels

2013 ◽  
Author(s):  
Liang-Han Chien ◽  
Han-Yang Liu ◽  
Wun-Rong Liao
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Flow Rate ◽  
Heat Sink ◽  
Heat Transfer Performance ◽  
Experimental Result ◽  
Working Fluid ◽  
Transfer Performance ◽  
Two Phase ◽  
Micro Channels

A heat sink integrating micro-channels with multiple jets was designed to achieve better heat transfer performance for chip cooling. Dielectric fluid FC-72 was the working fluid. The heat sink contained 11 micro-channels, and each channel was 0.8 mm high, 0.6 mm wide, and 12 mm in length. There were 3 or 5 pores on each micro-channel. The pore diameters were either 0.24 or 0.4 mm, and the pore spacing ranged from 1.5 to 3 mm. In the tests, the saturation temperature of cooling device was set at 30 and 50°C, and the volume flow rate ranged from 9.1 to 73.6 ml/min per channel (total flow rate = 100∼810 ml/min). The experimental result showed that heat transfer performance increased with increasing flow rate for single phase heat transfer. For heat flux between 20 and 100 kW/m2, the wall superheat decreases with increasing flow rate at a fixed heat flux. However, the influence of the flow rate diminished when the channels are in two phase heat transfer regime. Except for the lowest flow rate (9.1 ml/min), the heat transfer performance increased with increasing jet diameter/spacing ratios. The best surface had three nozzles of 0.4 mm diameter in 3.0 mm jet spacing. It had the lowest thermal resistance of 0.0611 K / W in the range of 200 ∼ 240 W heat input.

Experimental Study on Two-Phase Heat Transfer of FC-72 in Microchannels Heat Sink

2009 ◽  
Author(s):  
Xiao Hu ◽  
Guiping Lin ◽  
Hongxing Zhang
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Pressure Drop ◽  
Flow Rate ◽  
Mass Flux ◽  
Heat Sink ◽  
Heat Fluxes ◽  
High Mass ◽  
Two Phase ◽  
Two Phase Heat Transfer

A closed-loop two-phase microchannels cooling system using a micro-gear pump was built in this paper. The microchannels heat sink was made of oxygen-free copper, and 14 parallel microchannels with the dimension of 0.8mm(W)×1.5mm(D)×20mm(L) were formed by electric spark drilling followed by linear cutting which separated the channels from each other. The heat transfer performance was evaluated by the fluid temperature, the pressure drop across the micro-channels and the volumetric flow rate. Experiments were performed with refrigerant FC-72 which spanned the following conditions: initial pressure of Pin = 73 kPa, mass velocity of G = 94 – 333 kg/m2s, outlet quality of xe,out = 0 – superheat and heat flux of q″= 25–140 W/cm2. The result showed that, the maximum heat flux achieved 96 W/cm2, as the heating surface temperature was kept below 85 °C and critical heat flux occurred in the condition of low flow rate. Average two-phase heat transfer coefficients increased with the heat flux at low mass flux (G = 94 and 180 kg/m2s) and all heat fluxes, high mass flux (G = 333 kg/m2s) and all heat fluxes, and moderate mass fluxes (G = 224kg/m2s) under low and moderate heat fluxes (q″<110 W/cm2 for G = 224 kg/m2s), which was a feature of nucleate boiling mechanism. Pressure drop through microchannels heat sink was found to be below 4kPa.

scholarly journals Flow Boiling Heat Transfer to a Dielectric Coolant in a Microchannel Heat Sink

2005 ◽  
Author(s):  
Tailian Chen ◽  
Suresh V. Garimella
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Critical Heat Flux ◽  
Flow Rate ◽  
Heat Sink ◽  
Boiling Heat Transfer ◽  
Flow Boiling ◽  
Thermal Design ◽  
Microchannel Heat Sink ◽  
Flow Boiling Heat Transfer

This paper presents an experimental study of flow boiling heat transfer in a microchannel heat sink. The dielectric fluid Fluorinert FC-77 is used as the boiling liquid after it is fully degassed. The experiments were performed at three flow rates ranging from 30 to 50 ml/min. The heat transfer coefficients, as well as the critical heat flux, were found to increase with flow rate. Wall temperature measurements at three locations (near the inlet, near the exit, and in the middle of heat sink) reveal that wall dryout first occurs near the exit of the microchannels. The ratio of heat transfer rate under critical heat flux conditions to the limiting evaporation rate was found to decrease with increasing flow rate, asymptotically approaching unity. Predictions from a number of correlations for nucleate boiling heat transfer in the literature are compared against the experimental results to identify those that provide a good match. The results of this work provide guidelines for the thermal design of microchannel heat sinks in two-phase flow.   This paper was also originally published as part of the Proceedings of the ASME 2005 Heat Transfer Summer Conference.

scholarly journals Effect of liquid cooling on PCR performance with the parametric study of cross-section shapes of microchannels

2021 ◽  
Vol 11 (1) ◽  
Author(s):  
Yousef Alihosseini ◽  
Mohammad Reza Azaddel ◽  
Sahel Moslemi ◽  
Mehdi Mohammadi ◽  
Ali Pormohammad ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Cross Section ◽  
Cross Sections ◽  
Heat Sink ◽  
Evaluation Criteria ◽  
Circular Cross Section ◽  
Microchannel Heat Sink ◽  
Liquid Cooling ◽  
Maximum Heat ◽  
Maximum Heat Transfer

AbstractIn recent years, PCR-based methods as a rapid and high accurate technique in the industry and medical fields have been expanded rapidly. Where we are faced with the COVID-19 pandemic, the necessity of a rapid diagnosis has felt more than ever. In the current interdisciplinary study, we have proposed, developed, and characterized a state-of-the-art liquid cooling design to accelerate the PCR procedure. A numerical simulation approach is utilized to evaluate 15 different cross-sections of the microchannel heat sink and select the best shape to achieve this goal. Also, crucial heat sink parameters are characterized, e.g., heat transfer coefficient, pressure drop, performance evaluation criteria, and fluid flow. The achieved result showed that the circular cross-section is the most efficient shape for the microchannel heat sink, which has a maximum heat transfer enhancement of 25% compared to the square shape at the Reynolds number of 1150. In the next phase of the study, the circular cross-section microchannel is located below the PCR device to evaluate the cooling rate of the PCR. Also, the results demonstrate that it takes 16.5 s to cool saliva samples in the PCR well, which saves up to 157.5 s for the whole amplification procedure compared to the conventional air fans. Another advantage of using the microchannel heat sink is that it takes up a little space compared to other common cooling methods.

Performance Comparison of Microchannel Heat Sink Using Boron-Based Ceramic Materials

2021 ◽  
Vol 1163 ◽  
pp. 73-88
Author(s):  
Md Tanbir Sarowar
Keyword(s):  
Heat Transfer ◽  
Heat Flux ◽  
Heat Sink ◽  
Electronic Devices ◽  
Ceramic Materials ◽  
Substrate Material ◽  
Heat Sinks ◽  
Maximum Temperature ◽  
Microchannel Heat Sink ◽  
Small Surface

Microchannel heat sink plays a vital role in removing a considerable amount of heat flux from a small surface area from different electronic devices. In recent times, the rapid development of electronic devices requires the improvement of these heat sinks to a greater extent. In this aspect, the selection of appropriate substrate materials of the heat sinks is of vital importance. In this paper, three boron-based ultra-high temperature ceramic materials (ZrB2, TiB2, and HfB2) are compared as a substrate material for the microchannel heat sink using a numerical approach. The fluid flow and heat transfer are analyzed using the finite volume method. The results showed that the maximum temperature of the heat source didn’t exceed 355K at 3.6MWm-2 for any material. The results also indicated HfB2 and TiB2 to be more useful as a substrate material than ZrB2. By applying 3.6 MWm-2 heat flux at the source, the maximum obtained surface heat transfer coefficient was 175.2 KWm-2K-1 in a heat sink having substrate material HfB2.

Numerical Investigation of Flow Boiling in a Manifold Microchannel Heat Sink With Conjugate Heat Transfer

2019 ◽  
Author(s):  
Zhichuan Sun ◽  
Yang Luo ◽  
Junye Li ◽  
Wei Li ◽  
Jingzhi Zhang ◽  
...  
Keyword(s):  
Heat Transfer ◽  
Numerical Investigation ◽  
Heat Sink ◽  
Conjugate Heat Transfer ◽  
Flow Boiling ◽  
High Heat Flux ◽  
Microchannel Heat Sink ◽  
Two Phase ◽  
Boiling Process ◽  
Manifold Microchannel

Abstract The manifold microchannel heat sink receives an increasing number of attention lately due to its high heat flux dissipation. Numerical investigation of boiling phenomena in manifold microchannel (MMC) heat sinks remains a challenge due to the complexity of fluid route and the limitation of numerical accuracy. In this study, a computational fluid dynamics (CFD) approach including subcooled two-phase flow boiling process and conjugate heat transfer effect is performed using a MMC unit cell model. Different from steady-state single phase prediction in MMC heat sink, this type of modeling allows for the transient simulation for two-phase interface evolution during the boiling process. A validation case is conducted to validate the heat transfer phenomenon among three phases. Besides, this model is used for the assessment of the manifold dimensions in terms of inlet and outlet widths at the mass flux of 1300 kg/m2·s. With different ratios of inlet-to-outlet area, the thermal resistances remain nearly stable.

Sign in / Sign up

Export Citation Format

Share Document